3.
Baud Rate Selection Wire-wrap the desired channel pin (pin ~, 1, 2, or 3) to the correct baud rate pin. The following defines the baud rates at each lettered pin: Baud Rate 150 300 000 1200 2400 4800
Pin Letter U Factory Configuration channel U: 9.6K baud channell: 9.oK baud channel 2: 9.oK baud channel 3: 300 baud
T
V W y
L N
9600
19.2K 38.4K
K Z
4.
Note:
1) In the case of multiple channels at the same baud rate, it is necessary and permissible to daisy chain wire-wraps to conse~utive channel pins. 2) When 110 baud is supplied to a channel by the DLVll-KA option, ensure no baud rate jumper is inserted on that channel.
Communication Line Parameters Each channel is configured as described below for one channel: a.
Pan.ty Inhibit Selection
b. Jumper P
no parity* Pin X to 1 parity enabled Pin X to ~ c.
Number of Data Bits No. of bits 7 8
*Note: 5.
d.
Jumper D
Type Parity
Jumper E
even odd
Pin X to 1 Pin X to ~
Number of Stop Bits NO. of Bits
Pin X to ~ Pin X to 1
1
2
Jumper E must be connected to
~
Factory Configuration 1) No parity 2) Odd parity selected 3) 8 data bits 4) 1 stop blot
Jumper S Pin X to ~ Pin X to 1
or 1 even if no parity is selected
Console-Channel 3 Options Option
Jumper
*00 not send continual breaks to a system so confi.gurerl, as i.t will cause continued re-in~tializing of any device on the bus.
------------~~~~
hc:.It on break Pin X to H reboot on break* Pin X to B .ignore break No jumpers 6.
Parity Selection*
ErA Selection Channel E::A
~
is configured as described below:
Type
Jumpers ~
f1iJ
RS-413, RS-232C
X to 3
X to 3
RS-422
X to 2
X to 2
20mA*
removed
X to 3
*20mA capab~lity requires the DLVll-KA cable option. For TTY's with reader run relays, connect jumper N pin X to Pin R. Use of the DLVll-KA requires a 1.0 A pico-fuse in position Fl.
Channell (Nl, Ml), channel 2 (N2, M2), and channel 3 (N3, M3) are configured in an identical manner. 7.
Miscellaneous Jumper M is for manufacturing only - must be inserted.
Revisioo A
DLVll-J Conf1guration Guide (M8043) I = Jumper Inserted R = Jumper Rel'1Oved D = Don't Care 1.
.ro CHIJ ",.,d ClJl EI" c',l.,ctl-on -
2~3~
{
R3xa
I'..
,~... ~--~""'---"'-!r-:----:::ItU~--..J • • • "'" ~~. ••• Y} • • . . . . . . .1. M\ • • • IIe.W Baud rate • • • "'., N~ • • • 0 I. • K selection • • • • N3
z• •v
•••
eM.. "10 ..
~I
Select the base address for the four consecutive channels on this module (channels 0-+3)
o
•
LoU T
e. . .
..
•
3.....
IA Hle.::tion
Address Selection
Lf'I
D",
,
i - - - - C H l Term, L...._ _ _ CHili Term. L - - - - - C H 2 Term. L...._ _ _ _ CH3 Term.
S ..
Resistor ReSl-stor Resistor Resistor
ok
""•
•
Note:
selected by module
To configul'e address bits as a ~ or a 1, use the following chart:
Ca.>.
~:-l
address bit definition
Jumper
Baeters
"5 ••• "'''3 • • • AIZ • • •
~
address and vector jumpers
..
AlO • • •
•••
ello~
b~ection
C'L • • •
el ••• liS • • •
IlL---_1lL..----_ W
Vector Selection
8
0
f· , I '-J.--.'-/ I I I
I
I
I
Lf'I
I
I
selected by module
I
»>
Note: To configure the vector bits as a ~ or a 1, use the following chart: ',rector bit definition Jumper X to
Pin X to
1
Pw ~
n'~I~o'r" ceO +l
X
C
•.-4
Po
insert jumper
remove jumper
pin X to pin 1
pin X to pin ~
A-8 thru A-U
Chcmnel 3 immedl.ately following chani:.el
...
Wire-Wrap Connections C2-Pin x to Pin ~ Cl-Pin X to Pin ~
L-
as console device
C2-P,-;..n X to Pin 1 Cl-Pin X to Pin 1
to configure the last channel channel 3, at the console address of l77560,the base address of the board must be either 176500 176540 177500
Standard Configuration: Base address: l765XX, console device enabled
C
p,.p,.p,.p,.p,.
Remove
8
•.-4 •.-4
A-7
•.-4 •.-4 •.-4 •.-4 •.-4
1
St,;.udard Configuration: Vector at 3~~ (channel 3 at 60)
III
remove jumper
c c c c
X to
Inse,·t
III
insert jumper
~
1
console mode Pin Pin { V-5 Pin no console Pin :node V-6,V-7
A-6
Note:
Select a base vector for the four consecutive channels on this module (channel 0-+3).
~
pin X to pin ~
-.7 • •
,,8 • • •
r-
~
pin X to pin 1
vc. •• -n ••
All • • •
2.
1
A-5
0
0,0
'I
Cl: Pin X to Pin 1 C2: Pin X to Pin 1