Technical Information Micropilot M FMR250

TI390F/24/ae Technical Information Micropilot M FMR250 Level-Radar Smart Transmitter for continuous and non-contact leve...

4 downloads 208 Views 2MB Size
Technical Information

Micropilot M FMR250 Level-Radar Smart Transmitter for continuous and non-contact level measurement in solids. Cost-effective 4 to 20 mA 2-wire technology.

Application The Micropilot M performs continuous, non-contact level measurement especially in powdery to granular bulk solids. Additionally it can be used in liquids as well. Dust, filling noises, temperature layers and gas stratification do not affect measurement. Typical areas of application are: • Level measurement in tall silos with extremely dusty bulk solids e.g. cement, raw meal or animal feed. • Applications with high temperature requirements up to 200 °C (392 °F), e.g. clinker or fly ash. • Applications with highly abrasive bulk solids e.g. ferrite. The FMR250 with DN80 or DN100 horn antenna for all standard applications, particularly also for small nozzle sizes. The FMR250 with DN200 parabolic antenna offers high beam focussing of 4° and is thus ideal for applications with many installations.

TI390F/24/ae

Your benefits • 2-wire technology, low price: 2-wire technology reduces wiring costs and allows easy implementation into existing systems. • Non-contact measurement: Measurement is almost independent from product properties. • Easy on-site operation via menu-driven alphanumeric display. • Easy commissioning, documentation and diagnostics via Endress+Hauser operating software. • Integrated air purge connection for extremely dusty conditions or media tending to create build-up. • Max. measuring range 70 m (229 ft). • Suitable for process temperatures up to 200 °C (392 °F). • HART® or PROFIBUS® PA respectively FOUNDATION™ Fieldbus protocol. • Optional remote display and operation.

Micropilot M FMR250

Table of contents Function and system design. . . . . . . . . . . . . . . . . . . . . 3

Dielectric constant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Measuring principle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Equipment architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Mechanical construction . . . . . . . . . . . . . . . . . . . . . . 24

Measured variable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Measuring range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Measuring conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Operating frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Transmitting power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Design, dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . E+H UNI flange . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Process connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Seal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Human interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Output signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Signal on alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Linearization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Data of the FOUNDATION Fieldbus interface . . . . . . . . . . . . . . . . 9

Operation concept . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Display elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Operating elements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Local operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Remote operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Auxiliary energy . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Cable gland . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Terminal assignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Load HART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Supply voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Cable entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Power consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Current consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Ripple HART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Max. noise HART . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Overvoltage protector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Performance characteristics. . . . . . . . . . . . . . . . . . . . 15 Reference operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Maximum measured error . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Resolution . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Reaction time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 Influence of ambiente temperature . . . . . . . . . . . . . . . . . . . . . . . 15

Operating conditions: Installation . . . . . . . . . . . . . . . 16 Installation instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Beam angle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Installation in vessel FMR250 . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 FMR250 with top target positioner . . . . . . . . . . . . . . . . . . . . . . . 21 Integrated air purge connection . . . . . . . . . . . . . . . . . . . . . . . . . 21

24 26 27 27 27 27 27

28 28 29 30 31

Certificates and approvals . . . . . . . . . . . . . . . . . . . . . 35 CE approval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Ex approval . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . External standards and guidelines . . . . . . . . . . . . . . . . . . . . . . . . RF approvals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

35 35 35 35

Ordering information. . . . . . . . . . . . . . . . . . . . . . . . . 36 Micropilot M FMR250 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39 Weather protection cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Remote display FHX40 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Commubox FXA191 HART . . . . . . . . . . . . . . . . . . . . . . . . . . . . Commubox FXA195 HART . . . . . . . . . . . . . . . . . . . . . . . . . . . . Commubox FXA291 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ToF Adapter FXA291 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

39 39 40 40 40 40

Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Technical Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41 Certificates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Operating conditions: Environment. . . . . . . . . . . . . . 22 Ambient temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Storage temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Climate class . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Degree of protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Vibration resistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Cleaning of the antenna . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Electromagnetic compatibility (EMC). . . . . . . . . . . . . . . . . . . . . . 22

Operating conditions: Process . . . . . . . . . . . . . . . . . . 23 Process temperature range / Process pressure limits . . . . . . . . . . 23

2

Endress+Hauser

Micropilot M FMR250

Function and system design Measuring principle

The Micropilot is a "downward-looking" measuring system, operating based on the time-of-flight method. It measures the distance from the reference point (process connection) to the product surface. Radar impulses are emitted by an antenna, reflected off the product surface and received again by the radar system. Flange: reference point of measurement

20 mA 100% Flange: reference point of measurement

D E F

L 4 mA 0%

Threaded connection 1-½ BSPT (R 1-½”) or 1-½” NPT: reference point of measurement

L00-FMR250xx-15-00-00-en-001

Input The reflected radar impulses are received by the antenna and transmitted into the electronics. A microprocessor evaluates the signal and identifies the level echo caused by the reflection of the radar impulse at the product surface. The unambiguous signal identification is accomplished by the PulseMaster® software, based on many years of experience with time-of-flight technology. The distance D to the product surface is proportional to the time of flight t of the impulse: D = c · t/2, with c being the speed of light. Based on the known empty distance E, the level L is calculated: L=E–D Refer to the above figure for the reference point for "E". The Micropilot is equipped with functions to suppress interference echoes. The user can activate these functions. They ensure that interference echoes (i.e. from internals and struts) are not interpreted as level echo. Output The Micropilot is commissioned by entering an empty distance E (=zero), a full distance F (=span) and an application parameter. The application parameter automatically adapts the instrument to the process conditions. The data points “E” and “F” correspond with 4mA and 20mA for instruments with current output. They correspond with 0 % and 100 % for digital outputs and the display module. A linearization with max. 32 points, based on a table entered either manually or semi-automatically, can be activated locally or remotely. This function provides a measurement in engineering units and a linear output signal for spheres, horizontal cylindrical tanks and vessels with conical outlet.

Endress+Hauser

3

Micropilot M FMR250

Equipment architecture

Stand-alone The instrument provides a 4 to 20 mA output with HART protocol, or PROFIBUS PA respectively FOUNDATION Fieldbus communication. 4 to 20 mA output with HART protocol. The complete measuring system consists of:

PLC - FieldCare - ToF Tool - FieldTool Package

- FieldCare - ToF Tool - FieldTool Package

Service adapter FXA193

Commubox FXA191/195

Transmitter power supply unit RMA422 or RN221N (communication resistor included)

Operating and display module VU331

ENDRESS + HAUSER

%



+

E

dsdmdm df das. asdas fa asas la.

DELTABAR: * * * * * * * * ONLINE 1 QUICK SETUP 2 OPERATING MENU 3 PV 4 SV

HELP

SAVE

9

ENDRESS + HAUSER RMA 422

352 mbar 0 °C

Page Up

Bksp

6 Delete

Page On

#%&

ABC

1

2

Copy

Paste

GHI

3 MNO

5

6

Insert PQRS

+ Hot Key

TUV

W XY Z

8

7

FXA191/195 or DXR375

DEF Hot Key

JKL

4

9

,()‘

_

+*/

.

0

-

375 FIELD COMMUNICATOR

HART handheld DXR375

L00-FMR2xxxx-14-00-06-en-001

Local operation • with display and operating module VU331, • with a Personal Computer, FXA193 and the operating software "ToF Tool - FieldTool Package" respectively "FieldCare". The ToF Tool is a graphical operating software for instruments from Endress+Hauser that operate based on the time-of-flight principle (radar, ultrasonic, guided micro-impulse). It assists with commissioning, securing data, signal analysis and documentation of the measuring point. Remote operation • with HART handheld DXR375, • with a Personal Computer, Commubox FXA191/195 and the operating software "ToF Tool - FieldTool Package" respectively "FieldCare".

4

Endress+Hauser

Micropilot M FMR250

System integration via PROFIBUS PA A maximum of 32 transmitters (8 if mounted in an explosion hazardous location EEx ia IIC according to FISCO-model) can be connected to the bus. The segment coupler provides the operating voltage to the bus. Both on-site as well as remote operation are possible.The complete measuring system consists of: Personal computer e.g. with ToF Tool - FieldTool Package and Profibard resp. Proficard

PLC

Segment coupler PROFIBUS DP ENDRESS + HAUSER

PROFIBUS PA

T

More Functions (valves etc)

Operating and display module VU331

Service adapter · FXA291/ToF Adapter FXA291 · FSA193

ENDRESS + HAUSER

%



+

E

Prosonic M

Micropilot M

Levelflex M ToF Tool - FieldTool Package L00-FMxxxxxx-14-00-06-en-001

System integration via FOUNDATION Fieldbus A maximum of 32 transmitters (standard, EEx em or EEx d) can be connected to the bus. For protection class EEx ia IIC: the max. number of transmitters depends on the established rules and standards for intrinsically safe circuits (EN 60079-14), proof of intrinsically safety. Both on-site as well as remote operation are possible. The complete measuring system consists of:

Personal computer e.g. with NI-FBUS configurator

power supply

FF link

power conditioner

T

T

Additional functions (valves etc.)

Operating and display module VU331

Service adapter • FXA291/ToF Adapter FXA291 • FXA193

ENDRESS + HAUSER



%

+

E

Micropilot M

Prosonic M Levelflex M

ToF Tool FieldTool Package FieldCare

L00-FMxxxxxx-14-00-06-en-003

Endress+Hauser

5

Micropilot M FMR250

System integration via Fieldgate Vendor Managed Inventory By using Fieldgates to interrogate tank or silo levels remotely, suppliers of raw materials can provide their regular customers with information about the current supplies at any time and, for example, account for them in their own production planning. For their part, the Fieldgates monitor the configured level limits and, if required, automatically activate the next supply. The spectrum of options here ranges from a simple purchasing requisition via e-mail through to fully automatic order administration by coupling XML data into the planning systems on both sides. Remote maintenance of measuring equipment Fieldgates not only transfer the current measured values, they also alert the responsible standby personnel, if required, via e-mail or SMS. In the event of an alarm or also when performing routine checks, service technicians can diagnose and configure connected HART devices remotely. All that is required for this is the corresponding HART operating software (e.g. ToF Tool - FieldTool Package, FieldCare, ...) for the connected device. Fieldgate passes on the information transparently, so that all options for the respective operating software are available remotely. Some on-site service operations can be avoided by using remote diagnosis and remote configuration and all others can at least be better planned and prepared. Remote monitoring

Remote confoguration/diagnosis

HTTP script Web browser …

Via HART Client: - ToF Tool - FieldTool Package - FieldCare ...

Multidrop-Connector FXN520

e.g. 2 x RN221N-B …

ENDRESS+HAUSER RN 221N

Fieldgate FXA520

Channel 1

Channel 2

Analog Ethernet GSM FXN 520

ENDRESS+HAUSER RN 221N

Fieldgate FXA520

20 to 45 VDC

Hazardous Area

Non-hazardous Area

. L00-FXA520xx-14-00-06-en-009

Note! The number of instruments which can be connected in mutidrop mode can be calculated by the "FieldNetCalc" program. A description of this program can be found in Technical Information TI 400F (Multidrop Conncector FXN520). The program is available form your Endress+Hauser sales organisation or in the internet at: "www.endress.com Download" (Text Search = "Fieldnetcalc").

6

Endress+Hauser

Micropilot M FMR250

Input Measured variable

The measured variable is the distance between a reference point (refer to fig. on page 2) and a reflective surface (i.e. medium surface). The level is calculated based on the vessel height entered.The level can be converted into other units (volume, mass) by means of a linearization (32 points).

Measuring range

The usable measuring range depends on the size of the antenna, the reflectivity of the medium, the mounting location and eventual interference reflections. The maximum configurable range is 70 m (229 ft) for Micropilot M FMR250. Reduction of the max. possible measuring range through: • Media with poor reflection properties (= small DC). For examples refer to table 1. • Angle of repose. • Extremely loose surfaces of bulk solids, e.g. bulk solids with low bulk weight for pneumatic filling. • Build-up, above all of moist products. Table 1: The following table describes the media groups and the dielectric constant εr. Media group

DC (εr)

Examples

A

1.6 to 1.9

– Plastic granulate – White lime, special cement – Sugar

19 to 16 dB

B

1.9 to 2.5

– Portland cement, plaster

16 to 13 dB

C

2.5 to 4

– Grain, seeds – Ground stones – Sand

13 to 10 dB

D

4 to 7

– Naturally moist (ground) stones, ores – Salt

10 to 7 dB

E

>7

Signal attenuation

– Metallic powder – Carbon black – Coal

< 7 dB

The respective lower group applies for very loose or loosened bulk solids. Antenna selection

Endress+Hauser

Antenna type

Application

FMR250-*4*... 3" (DN80) FMR250-*5*... 4" (DN100)

The FMR250 with 3" (DN80) or 4" (DN100) horn antenna for all standard applications, particularly also for small nozzle sizes. To achieve an optimised signal strength it is recommended to use an antenna with as large as possible diameter. In small tanks in particular, an antenna extension should not be used wherever possible to optimize dynamics at close range.

FMR250-*6*... 8"(DN200)

The FMR250 with 8" (DN200) parabolic antenna offers high beam focussing of 4° and is thus ideal for applications with many installations.

7

Micropilot M FMR250

Measuring conditions

• The measuring range begins, where the beam hits the vessel bottom. Particularly with dish bottoms or conical outlets the level cannot be detected below this point. The maximum measuring range can be increased in such applications by using a top target positioner (see Page 16). • In case of media with a low dielectric constant (groups A and B), the vessel bottom can be visible through the medium at low levels. In order to guarantee the required accuracy in these cases, it is recommended to position the zero-point at a distance C = 2" to 6" (50...150 mm) above the vessel bottom (see Fig.). • In principle it is possible to measure up to the tip of the antenna with FMR250. However, due to considerations regarding abrasion and build-up, the end of the measuring range should not be chosen any closer than A=16" (400 mm, see Fig.) to the tip of the antenna.

A 100%

Measuring range

C 0%

L00-FMR250xx-17-00-00-en-001

Operating frequency

• FMR250: K-band

Transmitting power

Average energy density in beam direction:

8

Distance

Average energy density measuring range = 70 m (229 ft)

3 ft (1 m)

< 64 nW/cm2

16 ft (5 m)

< 2.5 nW/cm2

Endress+Hauser

Micropilot M FMR250

Output Output signal

• 4 to 20 mA with HART protocol • PROFIBUS PA – signal coding: Manchester Bus Powered (MBP); Manchester II – data transmission rate: 31.25 KBit/s, voltage mode • FOUNDATION Fieldbus (H1) – signal coding: Manchester Bus Powered (MBP); Manchester II – data transmission rate: 31.25 KBit/s, voltage mode

Signal on alarm

Error information can be accessed via the following interfaces: • Local display: – Error symbol – Plain text display • Current output • Digital interface

Linearization

The linearization function of the Micropilot M allows the conversion of the measured value into any unit of length or volume. Linearization tables for calculating the volume in cylindrical vessels are pre-programmed. Other tables of up to 32 value pairs can be entered manually or semi-automatically.

Data of the FOUNDATION Fieldbus interface

Basic Data Device Type

100F (hex)

Device Revision

05 (hex)

DD Revision

01 (hex)

CFF Revision

01 (hex)

ITK Version

5.0

ITK-Certification Driver-No.

IT042000

Link Master (LAS) cabable

yes

Link Master / Basic Device selectable

yes; Default: Basic Device

Number VCRs

24

Number of Link-Objects in VFD

24

Virtual communication references (VCRs) Permanent Entries

1

Client VCRs

0

Server VCRs

24

Source VCRs

23

Sink VCRs

0

Subscriber VCRs

23

Publisher VCRs

23

Link Settings

Endress+Hauser

Slot time

4

Min. Inter PDU delay

4

Max. response delay

10

9

Micropilot M FMR250

Transducer Blocks Block

Content

Output values

Sensor Block

contains all parameters related to the mesurement

• level or volume1) (channel 1) • distance (channel 2)

Diagnsotic Block contains diagnostic information

no output values

Display Block

no output values

1)

contains parameters to configure the local display

depends on sensor block configuration

Function Blocks Block

Content

Resource Block

The Resource Block contains all the data that uniquely identifies the field device. It is an electronic version of a nameplate of the device.

Analog Input Block 1 Analog Input Block 2

The AI block takes the manufacturer's input data, selected by channel number, and makes it available to other function blocks at its output.

30 ms

standard

PID Block

The PID block serves as proportional-integral-derivative controller and is used almost universally to do closedloop-control in the field including cascade and feedforward.

80 ms

standard

50 ms

standard

Input Selector Block

The input selector block provides selection of up to four 30 ms inputs and generates an output based on the configured action. This block normally receives its inputs from AI blocks. The block performs maximum, minimum, middle, average and ‘first good’ signal selection.

standard

Signal Characterizer Block

The signal characterizer block has two sections, each 40 ms with an output that is a non-linear function of the respective input. The non-linear function is determined by a single look-up table with 21 arbitrary x-y pairs.

standard

Integrator Block

The Integrator Function Block integrates a variable as a 60 ms function of the time or accumulates the counts from a Pulse Input block. The block may be used as a totalizer that counts up until reset or as a batch totalizer that has a setpoint, where the integrated or accumulated value is compared to pre-trip and trip settings, generating discrete signals when these settings are reached.

standard

Arithmetic Block This block is designed to permit simple use of popular measurement math functions. The user does not have to know how to write equations. The math algorithm is selected by name, chosen by the user for the function to be done.

10

Execution time

Functionality enhanced

Endress+Hauser

Micropilot M FMR250

Auxiliary energy Electrical connection

Terminal compartment Three housings are available: • Aluminium housing F12 with additionally sealed terminal compartment for: – standard, – Intrinsically safe (EEx ia), – Dust ignition proof (EEx ia with dust Ex). • Aluminium housing T12 with separate terminal compartment for: – standard, – Explosion proof (EEx d), – Intrinsically safe (EEx ia), with overvoltage protection, – Dust ignition proof (dust Ex). • 316L housing F23 for: – standard, – Intrinsically safe (EEx ia), – Dust ignition proof (EEx ia with dust Ex). The electronics and current output are galvanically isolated from the antenna circuit.

T12 housing

F12 housing

F23 housing

1 2 3 4

1 2 3 4

1 2 3 4

sealed terminal compartment

L00-FMR2xxxx-04-00-00-en-019

Cable gland

Terminals

Endress+Hauser

Type

Clamping area

Standard, Intrinsically safe, EEx ia

Plastic M20x1.5

5 to 10 mm

EEx em, EEx nA

Metal M20x1.5

7 to 10.5 mm

All

Metal, threaded

1/2" NPT

For wire cross-sections 16 to 18 AWG (0.5 to 2.5 mm2)

11

Micropilot M FMR250

Terminal assignment

2-wire, 4 to 20 mA with HART The 2-wire cable is connected to the screw terminals in the terminal compartment.

Power Alternatively

Cable specification: • A standard installation cable is sufficient if only the analog signal is used. Use a shielded cable when working with a superimposed communications signal (HART). Note! Protective circuitry against reverse polarity, RFI, and over-voltage peaks is built into the device (refer to TI241F »basics for EMC-tests«). Note! See TI402F/00/en for connection to Tank Side Monitor NRF590.

Commubox FXA 191/195 DXR 375

4 to 20 mA

Test sockets for testing of the signal current

1 2 3 4 L- L+ I+

Plant ground

IL00-FMxxxxxx-04-00-00-en-015

PROFIBUS PA The digital communication signal is transmitted to the bus via a 2-wire connection. The bus also provides the auxiliary energy. For further information on the network structure and earthing and for further bus system components such as bus cables, see the relevant documentation, e.g. Operating Instructions BA034S "Guidelines for planning and commissioning PROFIBUS DP/PA" and the PNO Guideline. Cable specification: • Use a twisted, shielded two-wire cable, preferably cable type A

1 2 3 4 – - ++

Plant ground

L00-FMxxxxxx-04-00-00-en-022

Note! For further information on the cable specifications, see Operating Instructions BA034S "Guidelines for planning and commissioning PROFIBUS DP/PA", PNO Guideline 2.092 "PROFIBUS PA User and Installation Guideline" and IEC 61158-2 (MBP). FOUNDATION Fieldbus The digital communication signal is transmitted to the bus via a 2-wire connection. The bus also provides the auxiliary energy. For further information on the network structure and earthing and for further bus system components such as bus cables, see the relevant documentation, e.g. Operating Instructions BA013S "FOUNDATION Fieldbus Overview" and the FONDATION Fieldbus Guideline. Cable specification: • Use a twisted, shielded two-wire cable, preferably cable type A

1 2 3 4 – - ++

Plant ground

L00-FMxxxxxx-04-00-00-en-022

Note! For further information on the cable specifications, see Operating Instructions BA013S "FOUNDATION Fieldbus Overview", FONDATION Fieldbus Guideline and IEC 61158-2 (MBP).

Load HART

12

Minimum load for HART communication: 250 Ω

Endress+Hauser

Micropilot M FMR250

Supply voltage

HART The following values are the voltages across the terminals directly at the instrument:

Communication

Terminal voltage

Current consumption

minimal

maximal

4 mA

16 V

36 V

20 mA

7.5 V

36 V

4 mA

16 V

30 V

20 mA

7.5 V

30 V

HART standard Intrinsically Safe (EEx ia)

Fixed current, adjustable e.g. for solar power operation (measured value transferred at HART)

Fixed current for HART Multidrop mode

1)

Explosion proof (EEx d)

4 mA

16 V

30 V

20 mA

11 V

30 V

Dust explosion proof (dust Ex)

4 mA

16 V

30 V

20 mA

11 V

30 V

standard

11 mA

10 V

36 V

Intrinsically Safe (EEx ia)

11 mA

10 V

30 V

standard

4 mA1))

16 V

36 V

Intrinsically Safe (EEx ia)

4 mA1)

16 V

30 V

Start up current 11 mA.

FOUNDATION Fieldbus Supply voltage

9 V to 32 V 1)

Lift-off voltage

9V

1)

There may be additional restrictions for devices with an explosion protection certificate. Refer to the notes in the appropriate safety instructions (XA).

Cable entry

• Cable gland: M20x1.5 (for EEx d: cable entry) • Cable entry: G ½ or ½" NPT

Power consumption

min. 60 mW, max. 900 mW

Current consumption

HART 3.6 to 22 mA. For HART Multidrop: start up current is 11 mA. PROFIBUS PA Max. 13 mA. FOUNDATION Fieldbus

Endress+Hauser

Basic current

15 mA

In-rush current

≤ 15 mA

Error current

0 mA

FISCO/FNICO compliant

yes

Polarity sensitive

no

13

Micropilot M FMR250

FISCO Ui

17.5 V

Ii

500 mA; with surge arrester 273 mA

Pi

5.5 W; with surge arrester1, 2 W

Ci

5 nF

Li

0.01 mH

Ripple HART

47 to 125 Hz: Uss = 200 mV (at 500 Ω)

Max. noise HART

500 Hz to 10 kHz: Ueff = 2.2 mV (at 500 Ω)

Overvoltage protector

The level transmitter Micropilot M with T12-housing (housing version "D", see ordering information on page 36-38) is equipped with an internal overvoltage protector (600 V surge arrester). Connect the metallic housing of the Micropilot M to the vessel wall or shield directly with an electrically conductive lead to ensure reliable potential matching.

14

Endress+Hauser

Micropilot M FMR250

Performance characteristics Reference operating conditions

• • • • •

Maximum measured error

Typical statements for reference conditions, include linearity, repeatability, and hysteresis: • up to 3 ft (1 m): ±1.18" (30 mm) • above 3 ft (1 m): ±0.60" (15 mm), or 0.04% of measuring range, whatever is larger

Resolution

Digital / analog in % 4 to 20 mA • FMR250: 0.04" (1mm) / 0.03 % of measuring range

Reaction time

The reaction time depends on the parameter settings (min. 1 s). In case of fast level changes, the instrument needs the reaction time to indicate the new value.

Influence of ambiente temperature

The measurements are carried out in accordance with EN 61298-3: • digital output (HART, PROFIBUS PA, FOUNDATION Fieldbus): – FMR250 average TK: 0.20"/10 K (5 mm/10 K), max. 0.60" (15 mm) over the entire temperature range -40 to +176°F (-40 to +80°C) • Current output (additional error, in reference to the span of 16 mA): – Zero point (4 mA) average TK: 0.03 %/10 K, max. 0.45 % over the entire temperature range -40 to +176°F (-40 to +80°C) – Span (20 mA) average TK: 0.09 %/10 K, max. 0.95 % over the entire temperature range -40 to +176°F (-40 to +80°C)

Endress+Hauser

temperature = +20 °C (68 °F) ±5 °C (9 °F) pressure = 1013 mbar abs. (14.7 psia) ±20 mbar (0.3 psi) relative humidity (air) = 65 % ±20% ideal reflector no major interference reflections inside the signal beam

15

Micropilot M FMR250

Operating conditions: Installation Installation instructions

Orientation • Recommended distance (1) wall – outer edge of nozzle: ~1/6 of vessel diameter. However, the device should not, under any circumstances, be mounted less than 20 cm (8") from the vessel wall. Note! If the tank wall is not smooth (corrugated metal, welding seams, irregularities etc.) the distance from the wall should be kept as large as possible. If necessary, use a top target positioner to prevent interference reflections from the tank wall. • Not in the centre (3), interference can cause signal loss. • Not above the fill stream (4). • It is recommended to use a weather protection cover (2) in order to protect the transmitter from direct sun or rain. Assembly and disassembly is simply done by means of a tension clamp (see Accessorieson page 39). • In extremely dusty applications, the integrated air purge connection can prevent clogging of the antenna.

2

3

4

1

L00-FMR250xx-17-00-00-xx-003

Vessel installations • Avoid any installations (1), like limit switches, struts, etc., inside the signal beam (see Beam angle on Page 17). • Symmetrical installations (2), i.e. reinforcing rings, heating coils, etc., can also interfere with the measurement. Optimization options • Antenna size: the bigger the antenna, the smaller the beam angle, the less interference echoes. • Mapping: the measurement can be optimized by means of electronic suppression of interference echoes. • Antenna alignment: refer to "Optimum mounting position" • In devices with top target positioner, the sensor can be optimally aimed within the vessel, and/or interference reflections can be avoided. The max. angle β is ±15°. • In particular, sensor alignment serves to: – prevent interference reflections – extend the maximum possible measuring range in conical outlets. • Metallic screens (3) mounted at a slope spread the radar signals and can, therefore, reduce interference echoes.

1

3

2

Please contact Endress+Hauser for further information. L00-FMR250xx-17-00-00-xx-002

16

Endress+Hauser

Micropilot M FMR250

Measurement in a plastic tank If the outer wall of the tank is made of a non-conductive material (e.g. GRP), microwaves can also be reflected off interfering installations outside the signal beam (e.g. metallic pipes (1), ladders (2), grates (3), …). Therefore, avoid such interfering installations in the signal beam.

auser Endress+H

ENDRESS+HAUS MICROPILOT ER II

VH 00

max. 20

U 16...36 4...20 mAV DC

IP 65

m

TA >70°C

: t >85°C

Made in Germany

Messbereich Measuring range

Maulburg

Order Code: Ser.-No.:

- +

V

H

auser Endress+H

ENDRESS+HAUS MICROPILOT ER II

VH 00

Order Code:

max. 20

U 16...36 4...20 mAV DC

IP 65

m

TA >70°C

TA >70°C

V

H

VH 00

Maulburg

IP 65

m

: t >85°C

Made in Germany

max. 20

U 16...36 4...20 mAV DC

- +

auser Endress+H

ENDRESS+HAUS MICROPILOT ER II

Order Code: Ser.-No.:

Messbereich Measuring range

: t >85°C

Made in Germany

Messbereich Measuring range

Maulburg

Ser.-No.:

- +

V

H

2

3

1

L00-FMR250xx-17-00-00-xx-014

Please contact Endress+Hauser for further information. Beam angle

The beam angle is defined as the angle a where the energy density of the radar waves reaches half the value of the maximum energy density (3dB-width). Microwaves are also emitted outside the signal beam and can be reflected off interfering installations. Beam diameter W as function of antenna type (beam angle α) and measuring distance D:

Parabolic antenna

80 mm / 3"

100 mm / 4"

200 mm / 8"

Beam angle α

10°





Measuring distance (D)

Endress+Hauser

Horn antenna

Antenna size FMR250

Beamwidth diameter (W) D

80 mm / 3"

100 mm / 4"

200 mm / 8"

5 m / 16 ft

0.87 m / 2.80 ft

0.70 m / 2.24 ft

0.35 m / 1.12 ft

10 m / 32 ft

1.75 m / 5.60 ft

1.40 m / 4.48 ft

0.70 m / 2.23 ft

15 m / 49 ft

2.62 m / 8.57 ft

2.10 m / 6.85 ft

1.05 m / 3.42 ft

20 m / 65 ft

3.50 m / 11.37 ft

2.80 m / 9.09 ft

1.40 m / 4.54 ft

30 m / 98 ft

5.25 m / 17.15 ft 4.20 m / 13.71 ft

2.10 m / 6.84 ft

40 m / 131 ft

7.00 m / 22.92 ft 5.59 m / 18.32 ft

2.79 m / 9.15 ft

50 m / 164 ft

8.75 m / 28.70 ft 6.99 m / 22.94 ft

3.50 m / 11.45 ft

W W = 2 . D . tan _ 2 L00-FMR2xxxx-14-00-06-de-027

17

Micropilot M FMR250

Installation in vessel FMR250

Optimum mounting position

90 °

Marker at instrument flange or threaded boss 1)

90°

°

90

1-½” NPT or 1-½” BSPT (R 1-½”)

90

°

ANIS 3” to 8” (DN 80 to 200)

90

°

1)

at version with top target positioner, the marker is at the housing adapter (opposite the air purge connection) L00-FMR250xx-17-00-00-en-009

Standard installation FMR250 with horn antenna • Observe installation instructions on Page 16. • Marker is aligned towards vessel wall. • The marker is always exactly in the middle between two bolt-holes in the flange. • After mounting, the housing can be turned 350° in order to simplify access to the display and the terminal compartment. • The horn antenna should protrude from the nozzle. If this is not possible for mechanical reasons, larger nozzle heights can be accepted. Note! Please contact Endress+Hauser for application with higher nozzle. • Vertical horn antenna. Ideally, the horn antenna should be installed vertically. To avoid interference reflections or for optimum alignment within the vessel, the FMR250 with optional top target positioner can be swiveled by 15° in all directions.

H

ØD

L00-FMR250xx-17-00-00-en-004

1)

18

Antenna size

80 mm / 3"

100 mm / 4"

D [mm / inch]

75 / 3

95 / 3.7

H [mm / inch] (without antenna extension)

< 260 / < 10.2

< 330 / < 12.9

1))

from 28.11.2005: H < 480 mm / 18.8 inch

Endress+Hauser

Micropilot M FMR250

Standard installation FMR250 with parabolic antenna • Observe installation instructions on Page 16. • Marker is aligned towards vessel wall. • The marker is always exactly in the middle between two bolt-holes in the flange. • After mounting, the housing can be turned 350° in order to simplify access to the display and the terminal compartment. • Ideally the parabolic antenna should protrude from the nozzle (1). Particularly when using the top target positioner, please ensure that the parabolic reflector is protruding from the nozzle/roof so as not to inhibit alignment. Note! For application with higher nozzle install parabolic antenna completely in the nozzle (2), including RF-wave guide (3). • Vertical parabolic antenna. Ideally, the parabolic antenna should be installed vertically. To avoid interference reflections or for optimum alignment within the vessel, the FMR250 with optional top target positioner can be swiveled by 15° in all directions.

1

H

ØD

2

3 L00-FMR250xx-17-00-00-en-005

Endress+Hauser

Antenna size

200 mm / 8"

D [mm / inch]

197 / 7.75

H [mm / inch] (without antenna extension)

< 50 / < 1.96

19

Micropilot M FMR250

Examples for installation with small flange (< parabolic reflector)

Standard installation

Nozzle

D

Antenna size D inches (mm) H inches (mm) 1)

H

For installation in nozzle, you can dismantle the parabolic reflector

8” (200 mm) 7.76 (197) < 1.97 (50)

1) without antenna extension

4 bolts

Caution! When installing on hinged flanges, the length of the antenna must be taken into account. Ensure the nozzle/opening is wide enough to accommodate the antenna tip.

L00-FMR250xx-17-00-00-en-007

20

Endress+Hauser

Micropilot M FMR250

FMR250 with top target positioner

Optimum mounting position Using the top target positioner it is possible to tilt the antenna axis by up to 15° in all directions. The top target positioner is used for the optimum alignment of the radar beam with the bulk solids surface.

±15°

±15°

L00-FMR250xx-17-00-00-de-008

Align antenna axis:

Integrated air purge connection

1.

Loosen screws.

2.

Align antenna axis (here this is possible up to max. ±15° in all directions).

3.

Tighten screws.

In extremely dusty applications, the integrated air purge connection can prevent clogging of the antenna. Pulsed operation is recommended. • Pulsed operation: max. pressure of purge air: 87 psi (6 bar abs.) • Permanent operation: recommended pressure range of the purge air: 2.9 to 7.3 psi (200 to 500 mbar). Caution! Make sure to use dry purge air.

Air purge connection: NPT ¼” or G ¼ (max. torque 2.6 lbf ft / 3.5 Nm)

L00-FMR250xx-17-00-00-en-010

Endress+Hauser

21

Micropilot M FMR250

Operating conditions: Environment Ambient temperature range

Ambient temperature for the transmitter: -40 to +80°C (-40 to +176°F), -50°C (-58°F) on request. The functionality of the LCD display may be limited for temperatures Ta+140°F (+60°C). A weather protection cover should be used for outdoor operation if the instrument is exposed to direct sunlight.

Storage temperature

-40 to +80°C (-40 to +176°F), -50°C (-58°F) on request.

Climate class

DIN EN 60068-2-38 (test Z/AD)

Degree of protection

• housing: IP 65, NEMA 4X (open housing and pulled out display: IP20, NEMA 1) • antenna: IP 68 (NEMA 6P)

Vibration resistance

DIN EN 60068-2-64 / IEC 68-2-64: 20 to 2000 Hz, 1 (m/s2)2/Hz

Cleaning of the antenna

The antenna can get contaminated, depending on the application. The emission and reception of microwaves can eventually be hindered. The degree of contamination leading to an error depends on the medium and the reflectivity, mainly determined by the dielectric constant εr. If the medium tends to cause contamination and deposits, cleaning on a regular basis is recommended. Care has to be taken not to damage the antenna in the process of a mechanical or hose-down cleaning (eventually air purge connection). The material compatibility has to be considered if cleaning agents are used! The maximum permitted temperature at the flange should not be exceeded.

Electromagnetic compatibility (EMC)

• Electromagnetic compatibility to EN 61326 and NAMUR recommendation EMC (NE 21). For details refer to the declaration of conformity. • A standard installation cable is sufficient if only the analogue signal is used. Use a screened cable when working with a superimposed communications signal (HART).

22

Endress+Hauser

Micropilot M FMR250

Operating conditions: Process Process temperature range / Process pressure limits

Note! The specified rage may be reduced by the selected process connection. The pressure rating (PN) specified on the nameplate refers to a reference temperature of 20°C, for ASME flanges to 100°F. Observe pressuretemperature dependency. The pressure values permitted at higher temperatures can be found in the following standards: • EN 1092-1: 2001 Tab. 18 With regard to its stability property, the material 1.4435 is identical to 1.4404 which is grouped under 13EO in EN 1092-1 Tab. 18. The chemical composition of the two materials can be identical. • ASME B 16.5a - 1998 Tab. 2-2.2 F316 • ASME B 16.5a - 1998 Tab. 2.3.8 N10276 • JIS B 2220 Type of antenna Seal FMR250

E

Standard

Temperature

FKM Viton GLT -40 to +200 °C (-40 to +392°F)

Pressure

Wetted parts 1)

-1 to 16 bar (-14.5 to 232 psi 1)

PEEK, seal, 316L SS/1.4404/1.4435

↑ Ordering information see Page 36 1)

E+H UNI flange: -1 to 1 bar (-14.5 to 14.5 psi)

Optional top target positioner: ±15°, seal: FMK Viton GLT Dielectric constant

Endress+Hauser

• In free space: εr ≥ 1.6 (for horizontal, even product surfaces: εr ≥ 1.4)

23

Micropilot M FMR250

Mechanical construction Design, dimensions

Housing dimensions Dimensions for process connection and type of antenna see Page 25.

2.56” (65)

max. 4.33” (110)

3.07” (78)

Ø 5.08” (129)

ENDRESS+HAUSER

5.91” (150)

F12 housing (Aluminum) 3.35” (85) L00-F12xxxx-06-00-00-en-001

max. 4.33” (110)

3.70” (94)

2.56” (65)

3.07” (78)

Ø 5.08” (129)

ENDRESS+HAUSER

5.91” (150) T12 housing (Aluminum)

3.35” (85) L00-T12xxxx-06-00-00-en-001

max. 3.70” (94)

1.57” (40)

4.09” (104)

Ø 5.08” (129) 5.91” (150)

F23 housing (316L SS)

L00-F23xxxx-06-00-00-en-001

24

Endress+Hauser

Micropilot M FMR250

Micropilot M FMR250 - process connection, type of antenna Housing dimensions see Page 24.

F12 / T12 / F23 housing

Threaded connection 1-½” NPT or 1 ½” BSPT (R 1 ½”)

Flange, 3” or 4” (DN 80 to 100) or equivalent

Ø 2.36” (60)

Ø 2.36” (60)

Ø 2.36” (60)

Ø 2.36” (60) 5.31” (135)

5.31” (135) 1.69” (43)

Alignment unit with E+H UNI flange, 4” / 8” ( DN 100/200)

E+H UNI flange 8” (DN 200)

5.31” (135)

0.31” (8)

5.31” (135)

0.31” (8)

1.57” (40)

b

Ø 8.86” (4” / DN100) Ø 13.4” (8” / Dn200)

Ø 13.4” (340)

ØD

0.91” (23)

Horn antenna

1.97” (50)

Parabolic antenna

1.97” (50)

1.06” (27)

1.06” (27)

9.84”/17.7” (250/450)

9.84”/17.7” (250/450) L

L 1.97” (50)

1.57” (40)

1.97” (50) 2.95” (75)

Ød L

L

Ød

2.95” (75)

Ød

Ød

Horn antenna

Flange to ANSI B16.5

3” (80 mm) 4” (100 mm) Antenna size L in (mm) 8.31 (211) 11.1 (282) 1) 3.74 (95) d in (mm) 2.95 (75) 1) 16.9” (430 mm) as of November 28, 2005

Flange b

3” 0.94”

4” 0.94”

D

7.50”

9.0”

Parabolic antenna Antenna size L in (mm) d in (mm)

8” (200 mm)

7.68 (195) 7.76 (197)

for Class 150

NOTE: Other process connections (DIN, JIS) are available, please contact Endress+Hauser.

L00-FMR250xx-06-00-00-en-005

Endress+Hauser

25

Micropilot M FMR250

E+H UNI flange

Installation hints The number of bolts has sometimes been reduced. The bolt-holes have been enlarged for adaption of dimensions, therefore, the flange needs to be properly aligned to the counterflange before the bolts are tightened. Dimensions are in inches (mm).

A-A

90 4x

4x90° 6x 60

°

°

E+H UNI flange 4” (DN100) compatible with - ANSI 4” Class 150 - DN100 PN10/16 - JIS 10K 100A

E+H UNI flange 8” (DN200) compatible with - ANSI 8” Class 150 - DN200 PN10/16 - JIS 10K 200A

0.31” (80)

M80x1.5

Ø 0.75” (19)

Ø 1.02” (26)

Ø 1.02” (26)

4x

90

°

Ø 0.91” (23)

A

A

A

A

11.6” (294.5) 6.89” (175)

13.4” (340)

7.30” (185.5) 8.86” (225)

Material: 316L

L00-FMR250xx-06-00-00-en-006

Top target positioner with E+H UNI flange

A-A

Clamping screw 3 x M8 shifted at 120°

Ø 3.35” (85)

A

A 1.57” (40)

0.31” (8)

Viton seal

E+H UNI flange 4”/8” (DN100/DN200) ±15°

L00-FMR250xx-06-00-00-en-007

26

Endress+Hauser

Micropilot M FMR250

Weight

Micropilot M

FMR250

Weight for F12 or T12 housing

Approx. 13 lb (6 kg) + weight of flange

Weight for F23 housing

Approx. 21 lb (9.4 kg) + weight of flange

Material

• Housing: – housing F12/T12: aluminum (AlSi10Mg), seawater-resistant, powder-coated – housing F23: 316L SS, corrosion-resistant steel • Sight window: glass

Process connection

See "Ordering information" on Page 36-38.

Seal

See "Ordering information" on Page 36-38.

Antenna

See "Ordering information" on Page 36-38.

Endress+Hauser

27

Micropilot M FMR250

Human interface Operation concept

The display of the process value and the configuration of the Micropilot occur locally by means of a large 4-line alphanumeric display with plain text information. The guided menu system with integrated help texts ensures a quick and safe commissioning. To access the display the cover of the electronic compartment may be removed even in hazardous area (IS and XP). Remote commissioning, including documentation of the measuring point and in-depth analysis functions, is supported via the ToF Tool, the graphical operating software for E+H time-of-flight systems.

Display elements

Liquid crystal display (LCD): Four lines with 20 characters each. Display contrast adjustable through key combination. LCD (liquid crystal display)

ENDR Order MICR ESS+ OPIL HAUS Ser.-NoCode: OT .: ER

II

IP T

Maulburg

range U 16...36 max. 4...20 20 m mAV DC

65

A >70°C

: t >85°C

Made in Germany

Messbe Measur reich ing

Symbols ENDRESS + HAUSER



+

E

3 keys Snap-fit

L00-FMxxxxxx-07-00-00-en-001

The VU331 LCD display can be removed to ease operation by simply pressing the snap-fit (see graphic above). It is connected to the device by means of a 20" (500 mm) cable. The following table describes the symbols that appear on the liquid crystal display: Sybmol

Meaning ALARM_SYMBOL This alarm symbol appears when the instrument is in an alarm state. If the symbol flashes, this indicates a warning. LOCK_SYMBOL This lock symbol appears when the instrument is locked,i.e. if no input is possible. COM_SYMBOL This communication symbol appears when a data transmission via e.g. HART, PROFIBUS PA or FOUNDATION Fieldbus is in progress. SIMULATION_SWITCH_ENABLE This communication symbol appears when simulation in FOUNDATION Fieldbus is enabled via the DIP switch.

28

Endress+Hauser

Micropilot M FMR250

Operating elements

The operating elements are located inside the housing and are accessible for operation by opening the lid of the housing. Function of the keys Key(s)

Meaning

O or V

Navigate upwards in the selection list Edit numeric value within a function

S or W

Navigate downwards in the selection list Edit numeric value within a function

X or Z F O and F or S and F O and S and F

Endress+Hauser

Navigate to the left within a function group

Navigate to the right within a function group, confirmation.

Contrast settings of the LCD

Hardware lock / unlock After a hardware lock, an operation of the instrument via display or communication is not possible! The hardware can only be unlocked via the display. An unlock parameter must be entered to do so.

29

Micropilot M FMR250

Local operation

Operation with VU331 The LC-Display VU331 allows configuration via 3 keys directly at the instrument. All device functions can be set through a menu system. The menu consists of function groups and functions. Within a function, application parameters can be read or adjusted. The user is guided through a complete configuration procedure. Headline

Position indicator

ENDRESS + HAUSER

Symbol



+

Main value

Bargraph

Unit

E Selection list

Function groups -> Functions HOME

X

F

X

FG00 FG01 FG02 FG03 FG04 FG05 FG06 FG07 ...

O S

F

F ...

F000 F001 F002 F003 F004

F

O S

X

X

Help text

Envelope curve L00-FMRxxxxx-07-00-00-en-002

Operation with handheld unit Field Communicator DXR375 All device functions can be adjusted via a menu operation with the handheld unit DXR375.

dsdmdm df das. asdas fa asas la.

dsdmdm df das. asdas fa asas la.

FMR231: LIC0001 ONLINE 1 GROUP SELECT 2 PV

HELP

8.7 m

FMR231: LIC0001 ONLINE 1 GROUP SELECTION 2 PV

Delete

8.7 m

SAVE

H HELP

Bksp

Delete

Page On

#%&

ABC

Bksp

2

3

Paste

Hot Key

GHI

JKL

MNO

PQRS

1 2 3 4 5

BASIC SETUP SAFETY SETTINGS LINEARISATION EXTENDED CALIB. OUTPUT

Delete

DEF

1 Copy

4

dsdmdm df das. asdas fa asas la.

FMR231: LIC0001 GROUP SELECTION

SAVE

Page Up

5

6

Insert

+ Hot Key

TUV

WXYZ

7

8

9

,()‘

_

+*/

.

0

-

H SAVE

HOME

Bksp

FMR231: LIC0001 BASIC SETUP 1 2 3 4 5

MEASURED VALUE TANK SHAPE MEDIUM PROPERTY PROCESS COND. EMPTY CALIBR.

dsdmdm df das. asdas fa asas la.

Page Up Page On

375 FIELD COMMUNICATOR SAVE

HOME

L00-FMR2xxxx-07-00-00-yy-007

Note! Further information on the handheld unit is given in the respective operating manual included in the transport bag of the DXR375.

30

Endress+Hauser

Micropilot M FMR250

Remote operation

The Micropilot M can be remotely operated via HART, PROFIBUS PA and FOUNDATION Fieldbus. Local adjustments are also possible. ToF Tool – Fieldtool Package The ToF Tool is a graphic and menu-guided operating program for measuring devices from Endress+Hauser. It is used for the commissioning, data storage, signal analysis and documentation of the devices. The following operating systems are supported: WinNT4.0, Win2000 and Windows XP. You can set all parameters via the ToF Tool. The ToF Tool supports the following functions: • Configuration of transmitters in online operation • Singal analysis via envelope curve • Tank linearisation • Loading and saving device data (upload/download) • Documentation of the measuring point Connection options: • HART via Commubox FXA191 and the RS 232 C serial interface of a computer • HART via Commubox FXA195 and the USB port on a computer • PROFIBUS PA via segment coupler and PROFIBUS interface card • FOUNDATION Fieldbus, PROFIBUS PA and HART via the FXA193/FXA291 service interface Note! You can use the ToF Tool to configure the Endress+Hauser parameters for devices with "FOUNDATION Fieldbus signal". You need an FF configuration program to be able to configure all the FF-specific parameters and to integrate the device into an FF network. FieldCare FieldCare is an Endress+Hauser asset management tool based on FDT technology. With FieldCare, you can configure all Endress+Hauser devices as well as devices from other manufacturers that support the FDT standard. The following operating systems are supported: WinNT4.0, Win2000 and Windows XP. FieldCare supports the following functions: • Configuration of transmitters in online operation • Signal analysis via envelope curve • Tank linearization • Loading and saving device data (upload/download) • Documentation of the measuring point Connection options: • HART via Commubox FXA191 and the RS 232 C serial interface of a computer • HART via Commubox FXA195 and the USB port on a computer • PROFIBUS PA via segment coupler and PROFIBUS interface card

Endress+Hauser

31

Micropilot M FMR250

Menu-guided commissioning

MicropilotM-en-415

Signal analysis via envelope curve

MicropilotM-en-416

32

Endress+Hauser

Micropilot M FMR250

Tank linearization

MicropilotM-en-417

Endress+Hauser

33

Micropilot M FMR250

Operation with NI-FBUS configurator (only FOUNDATION Fieldbus) The NI-FBUS Configurator is an easy-to-use graphical environment for creating linkages, loops, and a schedule based on the fieldbus concepts. You can use the NI-FBUS Configurator to configure a fieldbus network as follows: • Set block and device tags • Set device addresses • Create and edit function block control strategies (function block applications) • Configure vendor-defined function and transducer blocks • Create and edit schedules • Read and write to function block control strategies (function block applications) • Invoke Device Description (DD) methods • Display DD menus • Download a configuration • Verify a configuration and compare it to a saved configuration • Monitor a downloaded configuration • Replace devices • Log project download changes • Save and print a configuration

L00-fmxxxxxx-20-00-00-en-001

34

Endress+Hauser

Micropilot M FMR250

Certificates and approvals CE approval

The measuring system meets the legal requirements of the EC-guidelines. Endress+Hauser confirms the instrument passing the required tests by attaching the CE-mark.

Ex approval

See "Ordering information" on Page 36-38.

External standards and guidelines

EN 60529 Protection class of housing (IP-code) EN 61010 Safety regulations for electrical devices for measurement, control, regulation and laboratory use. EN 61326-X EMC product family standard for electrical equipment for measurement, control and laboratory use. NAMUR User association for automation technology in process industries.

RF approvals

Endress+Hauser

R&TTE, FCC

35

Micropilot M FMR250

Ordering information Micropilot M FMR250

Instrument selection

Non-hazardous area

Certificate

XP dust Ex

IS

Type of antenna/ Seal

E FKM Viton GLT

Communication

HART

PA

E FKM Viton GLT

FF

HART

PA

E FKM Viton GLT

FF

HART

PA

FF

Housing F12

F23

T12

F12

F23

T12

T12

L00-FMR250xx-16-00-00-en-001

36

Endress+Hauser

Micropilot M FMR250

Ordering structure Micropilot M FMR250 10

Approval: A 1 4 G B C D E I J Q L S T N U V Y

20

Non-hazardous area ATEX II 1/2G EEx ia IIC T6 ATEX II 1/2G EEx d [ia] IIC T6 ATEX II 3G EEx nA II T6 ATEX II 1/2GD EEx ia IIC T6, Alu blind cover ATEX II 1/2G EEx ia IIC T6, ATEX II 1/3D ATEX II 1/2D, Alu blind cover ATEX II 1/3D NEPSI Ex ia IIC T6 NEPSI Ex d(ia)ia IIC T6 NEPSI DIP TISS EEx d (ia) IIC T3 FM IS-Cl.I/II/III Div.1 Gr.A-G FM XP-Cl.I/II/III Div.1 Gr.A-G CSA General Purpose CSA IS-Cl.I/II/III Div.1 Gr.A-G CSA XP-Cl.I/II/III Div.1 Gr.A-G Special version

Antenna: 4 5 6 9

30

Horn 80mm/3" Horn 100mm/4" Parabolic 200mm/8" Special version

Antenna seal; Temperature: E Y

FKM Viton GLT; -40 to 200°C/-40 to 392 °F Special version

40

Antenna extension: 1 2 3 9

50

Not selected 250mm/10" 450mm/18" Special version

Process connection: GGJ GNJ

Thread EN10226 R1-1/2, 316L Thread ANSI NPT 1-1/2", 316L

X3J

UNI flange DN200/8"/200A, 316L max PN1/14.5lbs/1K, compatible DN200 PN10/16, 8" 150lbs, 10K 200A Top target pos., UNI DN100/4"/100A, 316L max PN1/14.5lbs/1K, compatible DN100 PN10/16, 4" 150lbs, 10K 100A Top target pos., UNI DN200/8"/200A, 316L max PN1/14.5lbs/1K, compatible DN200 PN10/16, 8" 150lbs, 10K 200A

XCJ XEJ

FMR250-

Endress+Hauser

CMJ CQJ

DN80 PN10/16 B1, 316L flange EN1092-1 (DIN2527 C) DN100 PN10/16 B1, 316L flange EN1092-1 (DIN2527 C)

ALJ APJ

3" 150lbs RF, 316/316L flange ANSI B16.5 4" 150lbs RF, 316/316L flange ANSI B16.5

KLJ KPJ YY9

10K 80A RF, 316L flange JIS B2220 10K 100A RF, 316L flange JIS B2220 Special version

Product designation (part 1)

37

Micropilot M FMR250

Ordering structure Micropilot M FMR250 (continued) 60

Output; Operation: A B K C D L E F M Y

70

4-20mA HART; 4-line display VU331, envelope curve display on site 4-20mA HART; w/o display, via communication 4-20mA HART; prepared for FHX40, remote display (Accessory) PROFIBUS PA; 4-line display VU331, envelope curve display on site PROFIBUS PA; w/o display, via communication PROFIBUS PA; prepared for FHX40, remote display (Accessory) FOUNDATION Fieldbus; 4-line display VU331, envelope curve display on site FOUNDATION Fieldbus; w/o display, via communication FOUNDATION Fieldbus; prepared for FHX40, remote display (Accessory) Special version

Housing: A B C D Y

80

F12 Alu, coated IP65 NEMA4X F23 316L IP65 NEMA4X T12 Alu, coated IP65 NEMA4X, separate connection compartment T12 Alu, coated IP65 NEMA4X + OVP, separate connection compartment, OVP = overvoltage protection Special version

Cable entry: 2 3 4 9

90

Gland M20x1.5 (EEx d > thread M20) Thread G1/2 Thread NPT 1/2" Special version

Additional option: K Air purge connection G1/4 M Air purge connection NPT 1/4" Y Special version

FMR250-

38

Complete product designation

Endress+Hauser

Micropilot M FMR250

Accessories Weather protection cover

A Weather protection cover made of stainless steel is recommended for outdoor mounting (order code: 543199-0001). The shipment includes the protective cover and tension clamp.

F12 / F23 / T12 housing

EN D M RE

Orde ICR SS r OP +HA Se Code r.-N ILO US o.: :

T II

Maulburg

ER

IP T

65

A >7

0°C

: t >8

5°C

Made in Germany

Me Messberei asuri ch ng ran ge U 16 ma x. 20 4...20...36 m mAV DC

L00-FMR2xxxx-00-00-06-en-001

Remote display FHX40 Wall-mounting (without mounting bracket)

5.91” (150)

Pipe-mounting (mounting bracket and plate supplied optionally, see product structure)

7.09” (180)

4.80” (122)

Micropilot M Levelflex M Prosonic M

0.33” (8.5)

Separate housing FHX 40, NEMA 4 (IP 65)

6.30” (160)

3.15” (80) EN DR ES S+ HA US ER

Ord er Co Se r.-N de: o.:

A >70

°C

°C

3.46” (88)

Cable 4.72” (120)

65

: t >85

Made in Germany

IP T

Maulburg

Me Messbere asu ich ring ran ge U 16. ma x. 20 4... ..36 20 m mAV DC

4.65” (118)

3.23” (82)

0.25” (6.3)

3.78” (96) max. 3.15” (80) min. 1.18” (30)

4.17” (106) 4.80” (122)

pipe

L00-FMxxxxxx-00-00-06-en-003

Technical data (cable and housing) and product structure:

Endress+Hauser

Max. cable length

20 m (65 ft)

Temperature range

-30 to +70 °C (-22 to 158 °F)

Degree of protection

IP65 acc. to EN 60529 (NEMA 4)

Materials

Housing: AlSi12; cable glands: nickle plated brass

Dimensions [mm] / [inch]

122 x 150 x 80 (HxWxD) / 4.8 x 5.9 x 3.2

39

Micropilot M FMR250

Approval: A 1 S U N K

Nn-hazardous area ATEX II 2 G EEx ia IIC T6, ATEX II 3D FM IS Cl.I Div.1 Gr.A-D CSA IS Cl.I Div.1 Gr.A-D CSA General Purpose TIIS ia IIC T6 (in preparation)

Cable: 1 5

20m/65ft; for HART 20m/65ft; for PROFIBUS PA/FOUNDATION Fieldbus

Additional option: A B

FHX40 -

Basic version Mounting bracket, pipe 1"/ 2"

Complete product designation

For connection of the remote display FHX40 use the cable which fits the communication version of the respective instrument. Commubox FXA191 HART

For intrinsically safe communication with ToF Tool/FieldCare via the RS232C interface. For details refer to TI237F/00/en.

Commubox FXA195 HART

For intrinsically safe communication with ToF Tool/FieldCare via the USB interface. For details refer to TI404F/00/en.

Commubox FXA291

The Commubox FXA291 connects Endress+Hauser field instruments with CDI interface (= Endress+Hauser Common Data Interface) to the USB interface of a personal computer or a notebook. For details refer to TI405C/07/en. Note! For the following Endress+Hauser instruments you need the "ToF Adapter FXA291" as an additional accessory: • • • • • • • • • • •

ToF Adapter FXA291

Cerabar S PMC71, PMP7x Deltabar S PMD7x, FMD7x Deltapilot S FMB70 Gammapilot M FMG60 Levelflex M FMP4x Micropilot FMR130/FMR131 Micropilot M FMR2xx Micropilot S FMR53x, FMR540 Prosonic FMU860/861/862 Prosonic M FMU4x Tank Side Monitor NRF590 (with additional adapter cable)

The ToF Adapter FXA291 connects the Commubox FXA291 via the USB interface of a personal computer or a notebook to the following Endress+Hauser instruments: • • • • • • • • • • •

Cerabar S PMC71, PMP7x Deltabar S PMD7x, FMD7x Deltapilot S FMB70 Gammapilot M FMG60 Levelflex M FMP4x Micropilot FMR130/FMR131 Micropilot M FMR2xx Micropilot S FMR53x, FMR540 Prosonic FMU860/861/862 Prosonic M FMU4x Tank Side Monitor NRF590 (with additional adapter cable)

For details refer to KA271F/00/a2.

40

Endress+Hauser

Micropilot M FMR250

Documentation Technical Information

Fieldgate FXA320, FXA520 Technical Information for Fieldgate FXA320/520, TI369F/00/en.

Operating Instructions

Micropilot M Correlation of operating instructions to the instrument:

Endress+Hauser

Instrument Output

Communication

Operating Instructions

Description of Instrument Functions

Brief Operating Instructions (in the Instrument)

FMR250

A, B, K

HART

BA284F/00/en

BA291F/00/en

KA235F/00/a2

C, D, L

PROFIBUS PA

BA331F/00/de

BA291F/00/de

KA235F/00/a2

E, F, M

FOUNDATION Fieldbus

BA336F/00/de

BA291F/00/de

KA235F/00/a2

41

Micropilot M FMR250

Certificates

Correlation of safety instructions (XA) and certificates (ZE) to the instrument:

Instrument Certificate Explosion protection

Output

Communication

FMR250

PTB 04 ATEX

XA







A

Non-hazardous area

A, B, C, D, K, L E, F, M

HART, PROFIBUS PA FOUNDATION Fieldbus

1

ATEX II 1/2G EEx ia IIC T6

A, B, K

HART

A, B, D

2108

XA313F

C, D, L E, F, M

PROFIBUS PA FOUNDATION Fieldbus

A, B, D

2108

XA343F

A, B, K

HART

C

2108

XA314F

C, D, L E, F, M

PROFIBUS PA FOUNDATION Fieldbus

C

2108

XA344F



2108

XA233F

4

ATEX II 1/2G EEx d [ia] IIC T6

G

ATEX II 3G EEx nA II T6

A, B, C, D, K, L E, F, M

HART, PROFIBUS PA FOUNDATION Fieldbus

B

ATEX II 1/2GD EEx ia IIC T6, Alu blind cover

A, B, K

HART

A, B

2108

XA312F

A, B

HART

D

2108

XA312F

C

D

E

42

Housing

ATEX II 1/2G EEx ia IIC T6 ATEX II 1/3D

ATEX II 1/2D, Alu blind cover

ATEX II 1/3D

C, D, L E, F, M

PROFIBUS PA FOUNDATION Fieldbus

A, B

2108

XA342F

C, D E, F

PROFIBUS PA FOUNDATION Fieldbus

D

2108

XA342F

A, B, K

HART

A, B

2108

XA312F

A, B

HART

D

2108

XA312F

C, D, L E, F, M

PROFIBUS PA FOUNDATION Fieldbus

A, B

2108

XA342F

C, D E, F

PROFIBUS PA FOUNDATION Fieldbus

D

2108

XA342F

A, B, K

HART

C

2108

XA315F

A, B

HART

A, B, D

2108

XA315F

C, D, L E, F, M

PROFIBUS PA FOUNDATION Fieldbus

C

2108

XA345F

C, D E, F

PROFIBUS PA FOUNDATION Fieldbus

A, B, D

2108

XA345F

A, B, K

HART

A, D, C

2108

XA315F

A, B

HART

B

2108

XA315F

C, D, L E, F, M

PROFIBUS PA FOUNDATION Fieldbus

A, D, C

2108

XA345F

C, D E, F

PROFIBUS PA FOUNDATION Fieldbus

B

2108

XA345F

Endress+Hauser

Micropilot M FMR250

Correlation of Control Drawings (ZD) to the instrument: Instrument

Certificate Explosion protection

Output

FMR250

S

A, B, K

HART

A, B

ZD168F/00/en

A, B

HART

D

ZD168F/00/en

ZD

PROFIBUS PA FOUNDATION Fieldbus

A, B

ZD208F/00/en

C, D E, F

PROFIBUS PA FOUNDATION Fieldbus

D

ZD208F/00/en

C

ZD169F/00/en

A, B

ZD170F/00/en

FM XP

A, B, K C, D, L E, F, M

HART PROFIBUS PA FOUNDATION Fieldbus

U

CSA IS

A, B, K

HART

A, B

HART

CSA XP

Housing

C, D, L E, F, M

T

V

Endress+Hauser

FM IS

Communication

D

ZD170F/00/en

C, D, L E, F, M

PROFIBUS PA FOUNDATION Fieldbus

A, B

ZD209F/00/en

C, D E, F

PROFIBUS PA FOUNDATION Fieldbus

D

ZD209F/00/en

A, B, K C, D, L E, F, M

HART PROFIBUS PA FOUNDATION Fieldbus

C

ZD171F/00/en

43

This product may be protected by at least one of the following patents. Further patents are pending. • • • • • • • • • • • • •

US 5,387,918 i EP 0 535 196 US 5,689,265 i EP 0 626 063 US 5,659,321 US 5,614,911 i EP 0 670 048 US 5,594,449 i EP 0 676 037 US 6,047,598 US 5,880,698 US 5,926,152 US 5,969,666 US 5,948,979 US 6,054,946 US 6,087,978 US 6,014,100

United States

Canada

Mexico

Endress+Hauser, Inc. 2350 Endress Place Greenwood, IN 46143 Tel. 317-535-7138 Sales 888-ENDRESS Service 800-642-8737 fax 317-535-8498 [email protected] www.us.endress.com

Endress+Hauser Canada 1075 Sutton Drive Burlington, ON L7L 5Z8 Tel. 905-681-9292 800-668-3199 Fax 905-681-9444 [email protected] www.ca.endress.com

Endress+Hauser, México, S.A. de C.V. Fernando Montes de Oca 21 Edificio A Piso 3 Fracc. Industrial San Nicolás 54030. Tlalnepantla de Baz Estado de México México Tel: +52 55 5321 2080 Fax +52 55 5321 2099 [email protected] www.mx.endress.com

TI390F/24/ae/09.07 © 2007 Endress+Hauser, Inc.