4600 C Montgomery Blvd. NE Albuquerque, NM 87109 main 505.883.4111 www.bpce.com
Feb 15, 2016
Barry Taylor 500 S.TAYLOR, ST. LOBBY BOX 254 SUITE 750 AMARILLO, TX 79101
SUBJECT: Vega Independent School District (VISD) – ADDENDUM #4 Dear Mr. Taylor: Please include the following information in your addendum to the bidders. We have prepared this addendum on a separate sheet such that your office need not retype this addendum information. Sincerely, BRIDGERS & PAXTON CONSULTING ENGINEERS, INC.
Robert Meador, PE Mechanical Project Engineer
Enclosure: Addenda and PDF Sketches
Addendum (RFP) Addendum No.: Addendum No. 4 Date: February 15, 2016 Project:
Vega Independent School District (VISD)
Project No.:
14-0424-002
From:
Bridgers and Paxton Dekker/Perich/Sabatini 7601 Jefferson St. NE, Suite 100 Albuquerque, NM 87109
To:
All Prospective Offerors and Plan Holders
This Addendum forms a part of the Procurement Documents and modifies the Procurement Documents issued by Dekker/Perich/Sabatini (D/P/S) and dated 2/15/2016. Acknowledge receipt of this Addendum on the Proposal Form. Failure to do so may subject the Offeror to disqualification. All other provisions of the Procurement Documents shall remain unchanged. This Addendum contains a total of Click here to enter text. sheet(s).
1.
SPECIFICATIONS: 1.1. Section 2030500-Common Work Requirements 1.1.1.Delete – All references to Uniform Mechanical Code – The International Mechanical Code shall apply. 1.1.2.Delete- All references to Uniform Plumbing Code– The International Plumbing Code shall apply. 1.1.3.Delete- All references to (PSFA) Design Guidelines. Change to: T.E.A. (Texas Education Agency) 1.2. Section 230505-Piping Secialties Subsection 2.18.B 1.2.1. Delete- Reference to City of Las Cruces and Replace with Vega, Texas. 1.3. Section 27 1622 – Cabling For Audio-Visual Systems 1.3.1.Add: New Specification Section 27 1622. 1.4. Section 27 4100 – Audio-Visual Systems 1.4.1.Add: New Specification Section 27 4100.
2.
MAIN BUILDING MECHANICAL DRAWINGS: 2.1. MH101C: LEVEL 1 HVAC PLAN - AREA C 2.1.1. Add: keynote#24,25. See revised sheet MH101C. 2.1.2. Add: 4” Flue and 4”Combustion air from water heaters up to roof. See revised sheet MH101C. 2.2. MH141C: ROOF MECHANICAL PLAN - AREA C 2.2.1. Add: keynote#6,7. See revised sheet MH141C. 2.2.2. Add: 4” Flue and 4” Combustion air from water heaters at the Mech room. See revised sheet MH141C.
3.
MAIN BUILDING PLUMBING DRAWINGS: 3.1. PL100A LOWER LEVEL WASTE & VENT PLAN: 3.1.1.Add: keynote#1 and 2. See revised sheet PL100A 3.2. PL100B LOWER LEVEL WASTE & VENT PLAN: 3.2.1.Add: keynote#1 and 2. See revised sheet PL100B 3.2.2.Add: Condensate piping for split system. Route elevator sump pump discharge piping. See revised sheet PL100B.
500 S.TAYLOR, ST. LOBBY BOX 254 SUITE 750 AMARILLO, TX 79101
Page 2 of 5
3.3. PL101B LEVEL 1 WASTE & VENT PLAN: 3.3.1.Add: Vent piping for art room sink. See revised sheet PL101B. 3.4. PL101C LEVEL 1 WASTE & VENT PLAN: 3.4.1.Add: keynote#4 and 5. See revised sheet PL101C 3.5. PL102A WASTE AND VENT PLAN – AREA A ALTERNATE: 3.5.1.Add: Sheet PL102A. 3.6. PL141 ROOF PLUMBING PLAN: 3.6.1.Add: keynote#1 thur 5. See revised sheet PL141. 3.7. PP101B LEVEL 1 PRESSURE PIPING PLAN: 3.7.1.Add: Art room sink call-out and kitchen sink call-out. See revised sheet PP101B. 3.8. PP101C LEVEL 1 PRESSURE PIPING PLAN: 3.8.1.Add: P20 call-out in Lab 131 and 135. Route water to wall hydrant P16. See revised sheet PP101C. 3.9. P501 PLUMBING DETAIL: 3.9.1.Revise: Floor drain and Domestic water heater detail. See revised Sheet P501. 3.10.
P502 PLUMBING DETAIL: 3.10.1. Add: Science room control panel and Island vent detail. See revised Sheet P502. 3.11. P7001 PLUMBING SPECIFICATIONS: 3.11.1. Add: P5, P6 and P20. Revised P15.See revised Sheet P701. 4.
AG BUILDING PLUMBING DRAWINGS: 4.1. PP101 AG SHOP PRESSURE PIPING PLAN: 4.1.1.Add: Gas piping to Domestic water heater. See revised sheet PP101. 4.2. P500a PLUMBING DETAIL: 4.2.1.Revise: Domestic water heater, floor drain, and wall cleanout details. See revised sheet P500a. 4.3. P501a PLUMBING DETAIL: 4.3.1.Revise: Gas meter/regulator details. See revised sheet P501a. 4.4. P700a PLUMBING SCHEDULES: 4.4.1.Revise: Pump schedules. See revised sheet P700a.
5.
MAIN BUILDING ELECTRICAL DRAWINGS: 5.1. ES101 ELECTRICAL SITE PLAN: 5.1.1.Revise- Location of fire alarm panels 5.2. EL100A LOWER LEVEL LIGHTING PLAN AREA A 5.2.1. Revise -All keyed note numbers have been revised. 5.3. EL100B LOWER LEVEL LIGHTING PLAN AREA B 5.3.1.Revise- All general notes. 5.3.2.Revise- All keyed note numbers have been revised. 5.4. EL101A LEVEL 1 LIGHTING PLAN AREA A 5.4.1.Revise- All general notes. 5.4.2.Revise- All keyed note numbers have been revised. 5.5. EL101B LEVEL 1 LIGHTING PLAN AREA B 5.5.1.Revise- All general notes. 5.5.2.Revise- All keyed note numbers have been revised. 5.6. EL101C LEVEL 1 LIGHTING PLAN AREA C 5.6.1.Revise- All general notes. 5.6.2.Revise- All keyed note numbers have been revised. 5.7. EL102A LIGHTING PLAN-BID LOT#3 5.7.1.Revise- All general notes. 5.8. EP100A LOWER LEVEL POWER PLAN-AREA A 5.8.1.Revise-All keyed note numbers have been revised. 5.9. EP100B LOWER LEVEL POWER PLAN-AREA B 5.9.1.Revise-All keyed note numbers have been revised.
500 S.TAYLOR, ST. LOBBY BOX 254 SUITE 750 AMARILLO, TX 79101
Page 3 of 5
5.9.2.Revise-Southeast corner of plan has architectural changes. 5.10. EP101A LEVEL 1 POWER PLAN-AREA A 5.10.1. Revise-all circuiting. 5.11. EP101B LEVEL 1 POWER PLAN-AREA B 5.11.1. Revise-All Keyed note numbers have been revised. 5.12. EP101C LEVEL 1 POWER PLAN-AREA C 5.12.1. Revise-All Keyed note numbers have been revised. 5.13. EP141A ROOF ELECTRICAL PLAN-AREA A 5.13.1. Revise-All Keyed note numbers have been revised. 5.14. EP141B ROOF ELECTRICAL PLAN-AREA B 5.14.1. Revise-All Keyed note numbers have been revised. 5.15. EP141C ROOF ELECTRICAL PLAN-AREA B 5.15.1. Revise-All Keyed note numbers have been revised. 5.16. FA100B LOWER LEVEL FIRE ALARM PLAN-AREA B 5.16.1. Revise-All Keyed note numbers have been revised. 5.17. FA101A LEVEL 1 FIRE ALARM PLAN-AREA A 5.17.1. Revise-All Keyed note numbers have been revised. 5.18. FA101C LOWER LEVEL FIRE ALARM PLAN-AREA C 5.18.1. Revise-All Keyed note numbers have been revised. 5.19. E401 ENLARGED CONCESSION KITCHEN 128, HOME EC 129 & STORAGES 5.19.1. Revise-All Keyed note numbers have been revised. 5.20. E501 ELECTRICAL DETAILS 5.20.1. Add- Detail D3 Linear Direct-Indirect Support Detail. 5.21. E604 LIGHTING DIAGRAMS & SEQUENCE OF OPERATION 5.21.1. Add-Detail B2 Watt Stopper “DLM” Wiring Diagram. 5.22. E703 ELECTRICAL PANEL SCHEDULES 5.22.1. Revise -Panel Circuiting on Panel L1B. 6.
AG BUILDING ELECTRICAL DRAWINGS: 6.1. EL101 AG SHOP LIGHTING PLAN 6.1.1.Revise- All Keyed note numbers have been revised. 6.2. EP101 AG SHOP POWER / FIRE ALARM PLAN 6.2.1.Revise- All Keyed note numbers have been revised.
7.
MAIN BUILDING TECH DRAWINGS: 7.1. T100A: LOWER LEVEL TECHNOLOGY SYSTEMS PLAN – AREA A 7.1.1.Add: A/V J-Box Tag “J3” to score keeper floor box. See revised sheet T100A. 7.1.2.Add: A/V J-Box Tag “J2” to junction box on west wall of Gym for A/V connection panel. See revised sheet T100A. 7.1.3.Add: Keyed Note #T33. See revised sheet T100A. 7.1.4.Add: Keynote Tag # T33 with leader pointing to A/V rack in room #B102. See revised sheet T100A. 7.2. T101A: LEVEL 1 TECHNOLOGY SYSTEMS PLAN – AREA A 7.2.1.Add: Speaker layout for Gymnasium sound system loudspeakers. See revised sheet T101A. 7.2.2.Add: A/V J-Box “J6” for each of the Gymnasium sound system loudspeakers. See revised sheet T101A. 7.2.3.Add: A/V J-Box/Pull Box “J5” for loudspeaker cabling on east wall of Gym. See revised sheet T101A. 7.2.4.Add: A/V J-Box/Pull Box “J4” for wireless microphone and assistive listening system antenna cabling on east wall of Gym. See revised sheet T101A. 7.3. T601: AUDIO-VISUAL DIAGRAMS 7.3.1.Add: Pathway Diagram D1 “A/V PATHWAY DIAGRAM: GYMNASIUM”. See revised sheet T601. 7.3.2.Revise: Functional Diagram A1 “SOUND SYSTEM FUNCTIONAL DIAGRAM: GYM – A/V SYSTEM TYPE A”. See revised sheet T601.
500 S.TAYLOR, ST. LOBBY BOX 254 SUITE 750 AMARILLO, TX 79101
Page 4 of 5
7.3.3.Replace: AUDIO-VISUAL J-BOX SCHEDULE. See revised sheet T601. 7.3.4.Revise: Keyed Note #1. See revised sheet T601. 7.3.5.Delete: Keyed Notes #2 through #8. See revised sheet T601.
All other provisions of the Contract Documents shall remain unchanged. This addendum is hereby made a part of the Contract Documents to the same extent as those provisions contained in the original documents and all itemized listings thereof. End of Addendum
500 S.TAYLOR, ST. LOBBY BOX 254 SUITE 750 AMARILLO, TX 79101
Page 5 of 5
Vega High School Addition Vega Independent School District
SECTION 27 1622 – CABLING FOR AUDIO-VISUAL SYSTEMS
PART 1 - GENERAL
1.1
RELATED DOCUMENTS A.
1.2
Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1 Specification Sections, apply to this Section.
SUMMARY A.
Work covered by this Section shall consist of furnishing labor, equipment, supplies, materials, and testing unless otherwise specified, and in performing the following operations recognized as necessary for the installation, termination, and labeling of cabling and connectors as described on the Drawings and/or required by these specifications.
B.
Related Sections: The following Sections contain requirements that relate to this Section. 1. 2. 3.
1.3
Division 26, Section 26 0500 “Common Work Results for Electrical”: Power supply, conduit and wiring. Division 27, Section 27 0500, Common Work Results for Communications. Division 27, Section 27 4100, Audio-Visual Systems.
REFERENCES A.
Underwriters Laboratories Inc. (UL)
B.
International Code Council (ICC): 1.
1.4
International Building Code, 2009 Edition as adopted by State of New Mexico 2009 Commercial Building Code.
SUBMITTALS A.
Product Data: For each type of product indicated. Include physical characteristics, UL classification types, conductor sizes, nominal impedances, and nominal capacitances. Reference each product to a location or “type” on Drawings. Test and evaluation data.
B.
Shop Drawings: The shop drawings listed below are required of the Contractor. Submit all Shop Drawings complete as a single submission. Isolated items will not be accepted, except with prior approval. 1. 2.
Cabling Schedule: A list containing the cable type, cable marker identifier, and origination and destination location and connector types for each cable. Examples of the Contractor’s final cable marking technique for each cable type.
Cabling for Audio-Visual Systems
27 1622 - 1
Vega High School Addition Vega Independent School District
1.5
QUALITY ASSURANCE A.
BICSI is an industry trade association. See Editing Instruction No. 2 in the Evaluations for summaries of qualifications for registration.
B.
Installer Qualifications: Cabling Installer must have personnel certified by BICSI on staff. 1. 2.
3. C.
Testing Agency Qualifications: An NRTL. 1.
1.6
Layout Responsibility: Preparation of Shop Drawings and Cabling Administration Drawings, Cabling Administration Drawings, and field testing program development by an RCDD. Installation Supervision: Installation shall be under the direct supervision of Registered Technician, or Level 2 Installer, who shall be present at all times when Work of this Section is performed at Project site. Testing Supervisor: Currently certified by BICSI as an RCDD to supervise on-site testing.
Testing Agency's Field Supervisor: Currently certified by BICSI as an RCDD to supervise on-site testing.
QUALIFICATIONS A.
Communications Cabling: The Contractor shall have 5 (five) years of documented experience performing cable placement, splicing, termination, connecting, and testing for each of the media types and 3 (three) years of applicable experience with the proposed system manufacturer. In the case of newer technologies that do not have a 3 (three) year history, the Contractor shall have documented experience for at least half of the lifetime of the new technology. The approved contractor shall, at a minimum, maintain a ratio of one manufacturer or BICSI certified installer for every two non-certified installers assigned to the project.
B.
The contractor shall provide resumes for the Project Manager, Supervisors and any skilled technicians or installers. Each resume shall include applicable certification documents provided by the manufacturer or BICSI. 1. 2.
1.7
Project Manager, Supervisors, and Principal Skilled Technicians: minimum of 5 years’ experience in like work. Category 6 Unshielded Twisted Pair and Fiber Optic Cable Technicians: documented training, licensing, and/or certification for the types of media specified, as applicable as well as certification from the manufacturer of the solution chosen by the owner.
PRIOR APPROVAL A.
1.8
For substitutions of products and/or manufacturers specified herein, Contractor shall submit requests for prior approval. Comply with provisions of Bidding Instructions and/or Division 1.
DELIVERY, STORAGE, AND HANDLING A.
Protection: Protect products from damage that may be caused by exposure to water, chemicals, direct sunlight or infestation.
Cabling for Audio-Visual Systems
27 1622 - 2
Vega High School Addition Vega Independent School District
B.
Waste Management and Disposal: Separate waste materials for recycling in accordance with Division 01, Section “Construction Waste Management and Disposal”. 1. 2. 3.
Remove packaging materials from site and dispose of at appropriate recycling facilities. Collect and separate for disposal paper, plastic, corrugated cardboard and/or polystyrene packaging materials in appropriate onsite bins for recycling. Dispose of all non-recyclable packaging materials and debris in a safe and environmentally responsible manner according to the instructions set forth by the General Contractor, local ordinances or codes and the Environmental Protection Agency.
PART 2 - PRODUCTS
2.1
GENERAL A.
Available Manufacturers: Subject to compliance with requirements, provide makes and models as listed below.
B.
The materials and products specified herein reflect the minimum acceptable standards of fabrication and manufacture. All materials and products supplied by the Contractor and specified herein are to be new, unused, of first quality and in original packaging or shipping containers or as shown on drawings and described in Part 3 below (for cabling).
C.
The products listed herein are pre-approved for this project. Substitutions shall be permitted for the manufacturers and products contained herein, provided they equal or exceed the specifications thereof and are pre-approved via formal request.
Cabling for Audio-Visual Systems
27 1622 - 3
Vega High School Addition Vega Independent School District
2.2
BULK CABLING
NOTE: Not all cable types listed are used in this project. Cabling for Audio-Visual Systems Schedule of Approved Bulk Cabling Signal Type/ ID Type / Application DIGITAL / ANALOG AUDIO
DA01
AES3 or Mic / Line (1 Pair)
Cable Type
24 AWG STP
DA02
AES3 or Mic / Line (Snake, 2 Pair)
24 AWG STP
DA04
AES3 or Mic / Line (Snake, 4 Pair)
24 AWG STP
DA06
AES3 or Mic / Line (Snake, 6 Pair)
24 AWG STP
DA12
AES3 or Mic / Line (Snake, 12 Pair)
24 AWG STP
Manuf.
Model
OSP/ Plenum
Nominal O.D. (in)
Belden
1800B
-
0.177
Belden
1801B
Plenum
0.165
Liberty
24-1P-DIG-AUD
-
0.203
Liberty
24-1P-P-DIG-AUDIO
Plenum
0.170
Belden
9729
-
0.266
Belden
89729
Plenum
0.255
Belden
9728
-
0.334
Belden
89728
Plenum
0.307
Belden
9731
-
0.421
Belden
89731
Plenum
0.361
Belden
9734
-
0.575
Belden
89734
Plenum
0.498
Belden
8450
-
0.118
Belden
82761
Plenum
0.116
Liberty
22-1P-EZ
-
0.142
Liberty
22-1P-CMP-EZ
Plenum
0.130
Belden
8723
-
0.160
Belden
82723
Plenum
0.153
Liberty
22-2P-INDSH-GRY
Liberty
22-2P-PINDSH-WHT
Belden
8777
-
0.273
Belden
82777
Plenum
0.234
Liberty
22-3P-INDSH-GRY
ANALOG AUDIO
AA01
AA02
AA03
AA04
Mic / Line Audio (Mono Signal)
Mic / Line Audio (Stereo Signal)
Mic / Line Audio (Snake, 3 Pair)
Mic / Line Audio (Snake, 4 Pair)
Cabling for Audio-Visual Systems
22 AWG STP
22 AWG STP
22 AWG STP
22 AWG STP
Plenum
-
Liberty
22-3P-PINDSH-WHT
Belden
8778
Plenum -
0.362
Belden
82778
Plenum
0.309
Liberty
22-4P-INDSH-GRY
Liberty
22-4P-PINDSH-WHT
Plenum
27 1622 - 4
Vega High School Addition Vega Independent School District Cabling for Audio-Visual Systems Schedule of Approved Bulk Cabling (cont'd) Type/ Signal ID Type / Application LOUDSPEAKER
L01
L02
L03
L04
L05
Loudspeaker (Constant Voltage)
Loudspeaker (Constant Voltage)
Loudspeaker (Low-Impedance)
Loudspeaker(LowImpedance)
Loudspeaker (Low-Impedance)
Cable Type
18 AWG UTP
16 AWG UTP
14 AWG UTP
12 AWG UTP
10 AWG UTP
Manuf.
Model
Belden
8461
Belden
6300UE
Liberty
18-2C-GRY
OSP/ Plenum
Nominal O.D. (in)
-
0.234
Plenum
0.157
-
0.160
Plenum
0.195
-
0.274
Plenum
0.180
Liberty
18-2C-P
Belden
8471
Belden
6200UE
Liberty
16-2C-GRY
-
0.183
Liberty
16-2C-TTP
Plenum
0.217
Belden
8473
-
0.340
Belden
5100UP
Plenum
0.260
Liberty
14-2C-GRY
-
0.230
Liberty
14-2C-TTP
Plenum
0.216
Belden
8477
-
0.386
Belden
5000UP
Plenum
0.302
Liberty
12-2C-GRY
-
0.274
Liberty
12-2C-TTP
Plenum
0.257
Belden
5T00UP
-
0.356
Belden
6T00UP
Plenum
0.308
Liberty
10-2C-KO-WHT
-
Liberty
10-2C-TTP-WHT
Plenum
Belden
8240
-
0.193
Belden
88240
Plenum
0.159
Liberty
RG58-CMR
-
0.195
Liberty
RG58-CMP
Plenum
0.178
Belden
9913
-
0.405
Belden
89913
Plenum
0.364
Liberty
WBC-400
-
Liberty
WBC-400P
Plenum
Belden
1530A
-
0.270
Belden
1530AP
Plenum
0.235
Liberty
RG6-CM-BLK
Liberty
RG6-P-CATV-WHT
Belden
1523A
-
0.400
Belden
1523AP
Plenum
0.348
Liberty
RG11-CATV-BLK
Liberty
RG11-P-CATV-WHT
RF DISTRIBUTION
RF01
RF02
RF03
RF04
50-ohm Antenna (Low Loss)
50-ohm Antenna (Ultra Low Loss)
75-ohm TV Distribution (RF)
75-ohm TV Distribution (RF, Ultra Low Loss)
Cabling for Audio-Visual Systems
20 AWG Coax (RG-58 Type)
10 AWG Coax (RG-8 Type)
18 AWG Coax (RG-6 Type)
14 AWG Coax (RG-11 Type)
Plenum
Plenum
27 1622 - 5
Vega High School Addition Vega Independent School District
Cabling for Audio-Visual Systems Schedule of Approved Bulk Cabling (cont'd) Type/ Signal ID Type / Application Cable Type Manuf. SERIAL DIGITAL / ANALOG COMPOSITE VIDEO
DV01
DV02
DV03
DV04
DV11
Serial Digital (HDSDI) or Composite (CVBS) Serial Digital (HDSDI) or Composite (CVBS) (Snake, Bundle of 3) Serial Digital (HDSDI) or Composite (CVBS) (Snake, Bundle of 4) Serial Digital (HDSDI) or Composite (CVBS) (Snake, Bundle of 10) SMPTE 292M / 424M or Composite (CVBS)
20 AWG Coax (RG-59 Type)
Model
OSP/ Plenum
Nominal O.D. (in)
Belden
1505A
-
0.233
Belden
1506A
Plenum
0.196
Liberty
20-CMR-VIDEO
Liberty
20-CMP-VID-COAX
Belden
-
0.236
Plenum
0.207
7794A
-
0.631
Liberty
RGB3C-20-CMR
-
20 AWG Coax (RG-59 Type)
Belden
7795A
-
0.706
20 AWG Coax (RG-59 Type)
Belden
7798A
-
1.166
Belden
1694A
-
0.275
Belden
1695A
Plenum
0.234
Liberty
18-CMR-SD
-
0.272
Liberty
18-CMP-VID-COAX
Plenum
0.237
20 AWG Coax (RG-59 Type)
18 AWG Coax (RG-6 Type)
DV12
SMPTE 292M / 424M or Composite (CVBS) (Snake, Bundle of 3)
18 AWG Coax (RG-6 Type)
Belden
7710A
-
0.770
DV13
SMPTE 292M / 424M or Composite (CVBS) (Snake, Bundle of 4)
18 AWG Coax (RG-6 Type)
Belden
7711A
-
0.900
DV14
SMPTE 292M / 424M or Composite (CVBS) (Snake, Bundle of 10)
18 AWG Coax (RG-6 Type)
Belden
7713A
-
1.386
Belden
1808A
-
0.255
Belden Liberty Liberty
7700A SV-PVC SV-PLN
Plenum Plenum
0.460 0.270 0.230
-
0.320
Plenum -
0.276 0.401
S-VIDEO
SV01
S-Video (Y/C)
26-30 AWG Coax, Stranded (Qty.2 bundled)
COMPONENT VIDEO CV01
Component Video (Y/Pb/Pr)
Cabling for Audio-Visual Systems
25 AWG Coax (Qty.3 bundled)
Belden
1277R
Belden Liberty
1277P RGB3-MINI
27 1622 - 6
Vega High School Addition Vega Independent School District
Cabling for Audio-Visual Systems Schedule of Approved Bulk Cabling (cont'd) Type/ Signal ID Type / Application RGBHV VIDEO
PV01
PV02
RGBHV Video
RGBHV Video (Super High Res)
Cable Type
25 AWG Coax (Qty.5 bundled)
20 AWG Coax (Qty.5 bundled)
CRESTRON DIGITALMEDIA (DM) 24 AWG x8 UTP + 24 AWG x8 STP DM01 DigitalMedia + 22 AWG x2 STP + 18 AWG x2 UTP DigitalMedia (DM) “D” only – for upgrade of existing DM02 QuickMedia “QM” 24 AWG x8 STP type cabling (reduced conduit capacity requirements) DM03
DigitalMedia (DM) 8G
24 AWG x8 STP
CresFiber - For: DigitalMedia Fiber DigitalMedia 8G 50/125 micron DM11 Fiber MM Fiber x4 Crestron HDMI over Fiber CRESTRON QUICKMEDIA (QM) 24 AWG x8 UTP + QM01 QuickMedia (QM) 22 AWG x2 STP + 18 AWG x2 UTP CRESTRON IMEDIA (IM) 24 AWG x8 UTP IM01 iMedia (iM) + 20 AWG Drain
Cabling for Audio-Visual Systems
Manuf.
Model
OSP/ Plenum
Nominal O.D. (in)
Belden
1279R
-
0.403
Belden
1279P
Plenum
0.335
Liberty
RGB5C-25-CM
-
0.350
Liberty
RGB5C-25-CMP
Plenum
0.315
Belden
7796A
-
0.790
Belden
1283S5
Plenum
0.529
Liberty
RGB5C-20-CMR
-
0.740
Crestron Crestron Liberty
DM-CBL-NP DM-CBL-P LLINX-DM
Plenum -
0.580 0.580 0.613
Liberty
LLINX-QM-P + 24-4P-P-L6SH
Plenum
0.20 x 0.40 + 0.268
Crestron Crestron Liberty
DM-CBL-D-NP DM-CBL-D-P 24-4P-L6ASH
Plenum -
0.300 0.300 0.319
Liberty
24-4P-P-L6[A]SH
Plenum
0.268
Crestron Crestron Liberty Liberty
DM-CBL-8G-NP DM-CBL-8G-P LLINX-HD LLINX-P-HD
Plenum Plenum
0.244 0.244 0.250 0.250
Crestron
CRESFIBER8G-NP
-
0.313
Crestron
CRESFIBER8G-P
Plenum
0.313
Plenum Crestron Crestron Liberty
CRESCAT-QM-NP CRESCAT-QM-P n/a
Plenum -
0.236 x 0.480 0.216 x 0.431
Liberty
LLINX-QM-P
Plenum
0.20 x 0.40
Crestron
n/a
Crestron
CRESCAT-IM-P-DRN
Plenum
0.248 x 0.433
27 1622 - 7
Vega High School Addition Vega Independent School District
Cabling for Audio-Visual Systems Schedule of Approved Bulk Cabling (cont'd) Type/ Signal ID Type / Application CRESTRON CRESNET
Cable Type
CN01
Cresnet
22 AWG x2 STP + 18 AWG x2 UTP
CN02
Cresnet "HighPower"
22 AWG x2 STP + 12 AWG x2 UTP
Manuf.
Model
Crestron Crestron Liberty Liberty Crestron Crestron Liberty Liberty
CRESNET-NP CRESNET-P LLINX-U LLINX-U-P CRESNET-HP-NP n/a LLINX-U-HP n/a
Belden
OSP/ Plenum
Nominal O.D. (in)
Plenum Plenum Plenum Plenum
0.250 0.216 0.246 0.205 0.330
1700A
-
0.200
Belden
1701A
Plenum
0.195
Liberty
24-4P-L5-EN
-
0.197
Liberty
24-4P-P-L5-EN
Plenum
0.180
0.315
UTP
U01
U02
U12
U13
Ethernet/ A/V over UTP (Cat5e)
Ethernet/ A/V over UTP (Cat6)
A/V over UTP (Cat5e Low-Skew)
A/V over UTP (Cat6 Low-Skew)
24 AWG UTP (4pr)
23 AWG UTP (4pr)
24 AWG UTP (4pr, Low-Skew)
23 AWG UTP (4pr, Low-Skew)
Belden
7851A
-
0.315
Belden
7852A
Plenum
0.290
Liberty
24-4P-L6-EN
-
0.220
Liberty
24-4P-P-L6-EN
Plenum
0.215
Berk-Tek
10139885
OSP
0.250
Belden
7988R
-
0.204
Belden
7988P
Plenum
0.193
Belden
7989R
-
0.365
Belden
7989P
Plenum
0.365
Liberty
TRUPHASE
-
0.205
Liberty
TRUPHASE-P
Plenum
0.170
Belden
1533R
-
0.260
Belden
1533P
Plenum
0.235
Liberty
24-4P-L5SH-EN
-
0.237
STP
S01
S02
Ethernet/ A/V over STP (Cat5e)
Ethernet/ A/V over STP (Cat6)
Cabling for Audio-Visual Systems
24 AWG ScTP (4pr)
23 AWG ScTP (4pr)
Liberty
24-4P-P-L5SH
Plenum
0.225
Belden
1351A
-
0.290
Belden
1352A
Plenum
0.285
Liberty
24-4P-L6SH
-
0.270
Liberty
24-4P-P-L6SH
Plenum
0.268
27 1622 - 8
Vega High School Addition Vega Independent School District
Cabling for Audio-Visual Systems Schedule of Approved Bulk Cabling (cont'd) Type/ ID FIBER
Signal Type / Application
Cable Type
Manuf.
Model
OSP/ Plenum
Nominal O.D. (in)
F06
SM Fiber (Bundle of 6)
250 micron
Mohawk
M9W810
OSP
0.255
F12
SM Fiber (Bundle of 12)
250 micron
Mohawk
M9W811
OSP
0.255
F24
SM Fiber (Bundle of 24)
250 micron
Mohawk
M9W812
OSP
.245 x .495
Belden
8104
-
0.302
Belden
88104
Plenum
0.259
Liberty
24-4P-SH-LIBII
-
0.210
Liberty
24-4P-PLCSH
Plenum
0.210
Belden
9842
-
0.340
Belden
82842
Plenum
0.273
Liberty
24-2P-485
-
0.326
Liberty
24-2P-P485-WHT
Plenum
0.277
Belden
8761
-
0.175
Belden
82761
Plenum
0.116
CONTROL
C01
C02
C11
IR & Serial Control (RS-232/-422)
Serial Control (RS485) or DMX-512 (4-cond) Dry Contact & Signal Input/Output
24 AWG STP (4pr)
24 AWG STP (2pr)
22 AWG STP (1pr)
[End]
Cabling for Audio-Visual Systems
27 1622 - 9
Vega High School Addition Vega Independent School District
2.3
APPROVED CABLE ASSEMBLIES & ADAPTERS
NOTE: Not all cable assemblies and adapters listed are used in this project. Cabling for Audio-Visual Systems Schedule of Approved Cable Assemblies & Adapters TYPE
MFR
PART #
MODEL #
DESCRIPTION
ANALOG AUDIO - UNBALANCED AU01
Tecnec
N/A
2P-2P-3
RCA Stereo Audio, Male-to-Male, 3ft
AU02
Tecnec
N/A
2P-2P-6
RCA Stereo Audio, Male-to-Male, 6ft
AU03
Tecnec
N/A
2P-2P-10
RCA Stereo Audio, Male-to-Male, 10ft
AU04
Tecnec
N/A
2P-2P-15
RCA Stereo Audio, Male-to-Male, 15ft
AU05
Tecnec
N/A
2P-2P-25
RCA Stereo Audio, Male-to-Male, 25ft
AU06
Tecnec
N/A
2P-2P-50
RCA Stereo Audio, Male-to-Male, 50ft
AU07
Tecnec
N/A
2P-2P-75
RCA Stereo Audio, Male-to-Male, 75ft
AU08
Tecnec
N/A
2P-2P-100
RCA Stereo Audio, Male-to-Male, 100ft
AU11
Extron
26-641-06
A-RCA/6
RCA Stereo Audio, Male-to-Male, 6ft
AU12
Extron
26-641-10
A-RCA/10
RCA Stereo Audio, Male-to-Male, 10ft
AU13
Extron
26-641-25
A-RCA/25
RCA Stereo Audio, Male-to-Male, 25ft
AU21
Tecnec
N/A
MPS-MPS-3
3.5mm Stereo Audio, Male-to-Male, 3ft
AU22
Tecnec
N/A
MPS-MPS-6
3.5mm Stereo Audio, Male-to-Male, 6ft
AU23
Tecnec
N/A
MPS-MPS-10
3.5mm Stereo Audio, Male-to-Male, 10ft
AU24
Tecnec
N/A
MPS-MPS-15
3.5mm Stereo Audio, Male-to-Male, 15ft
AU25
Tecnec
N/A
MPS-MPS-25
3.5mm Stereo Audio, Male-to-Male, 25ft
AU26
Tecnec
N/A
MPS-MPS-50
3.5mm Stereo Audio, Male-to-Male, 50ft
AU27
Tecnec
N/A
MPS-MPS-75
3.5mm Stereo Audio, Male-to-Male, 75ft
AU28
Tecnec
N/A
MPS-MPS-100
3.5mm Stereo Audio, Male-to-Male, 100ft
AU31
Extron
26-571-01
A-MINI/2
3.5mm Stereo Audio, Male-to-Male, 2ft
AU32
Extron
26-571-03
A-MINI/6
3.5mm Stereo Audio, Male-to-Male, 6ft
AU33
Extron
26-571-05
A-MINI/10
3.5mm Stereo Audio, Male-to-Male, 10ft
AU34
Extron
26-571-06
A-MINI/12
3.5mm Stereo Audio, Male-to-Male, 12ft
AU35
Extron
26-571-07
A-MINI/25
3.5mm Stereo Audio, Male-to-Male, 25ft
ANALOG AUDIO - BALANCED Gepco, Canare, Whirlwind, Switchcraft, ADC AUDIO & VIDEO PATCH CORDS Gepco, Canare, Whirlwind, Switchcraft, ADC
Cabling for Audio-Visual Systems
27 1622 - 10
Vega High School Addition Vega Independent School District
Cabling for Audio-Visual Systems Schedule of Approved Cable Assemblies & Adapters (cont'd) TYPE
MFR
PART #
MODEL #
DESCRIPTION
DIGITAL AUDIO AD01
Tecnec N/A
SPDIF1.5
SPDIF RCA 75ohm, Male-to-Male, 18in
AD02
Tecnec N/A
SPDIF3
SPDIF RCA 75ohm, Male-to-Male, 3ft
AD03
Tecnec N/A
SPDIF6
SPDIF RCA 75ohm, Male-to-Male, 6ft
AD04
Tecnec N/A
SPDIF10
SPDIF RCA 75ohm, Male-to-Male, 10ft
AD05
Tecnec N/A
SPDIF15
SPDIF RCA 75ohm, Male-to-Male, 15ft
AD06
Tecnec N/A
SPDIF20
SPDIF RCA 75ohm, Male-to-Male, 20ft
AD07
Tecnec N/A
SPDIF25
SPDIF RCA 75ohm, Male-to-Male, 25ft
AD08
Tecnec N/A
SPDIF30
SPDIF RCA 75ohm, Male-to-Male, 30ft
AD09
Tecnec N/A
SPDIF40
SPDIF RCA 75ohm, Male-to-Male, 40ft
AD10
Tecnec N/A
SPDIF50
SPDIF RCA 75ohm, Male-to-Male, 50ft
AD11
Tecnec N/A
OPT-103
Optical Toslink, 3ft
AD12
Tecnec N/A
OPT-106
Optical Toslink, 6ft
AD13
Tecnec N/A
OPT-110
Optical Toslink, 10ft
AD14
Tecnec N/A
OPT-130
Optical Toslink, 30ft
AD15
Tecnec N/A
OPT-150
Optical Toslink, 50ft
RF DISTRIBUTION RF01
Extron 26-383-01 RG6-BNC/3
RG6 BNC 75ohm, Male-to-Male, 3ft
RF02
Extron 26-383-12 RG6-BNC/6
RG6 BNC 75ohm, Male-to-Male, 6ft
RF03
Extron 26-383-07 RG6-BNC/12 RG6 BNC 75ohm, Male-to-Male, 12ft
RF04
Extron 26-383-04 RG6-BNC/25 RG6 BNC 75ohm, Male-to-Male, 25ft
RF05
Extron 26-383-13 RG6-BNC/35 RG6 BNC 75ohm, Male-to-Male, 35ft
RF06
Extron 26-383-05 RG6-BNC/50 RG6 BNC 75ohm, Male-to-Male, 50ft
RF07
Extron 26-383-06 RG6-BNC/75 RG6 BNC 75ohm, Male-to-Male, 75ft
RF08
Extron 26-383-03 RG6-BNC/100 RG6 BNC 75ohm, Male-to-Male, 100ft
COMPOSITE VIDEO CVBS01 Extron 26-600-03 RCA/3
RCA Composite Video, Male-to-Male, 3ft
CVBS02 Extron 26-600-01 RCA/6
RCA Composite Video, Male-to-Male, 6ft
CVBS03 Extron 26-600-15 RCA/15
RCA Composite Video, Male-to-Male, 15ft
CVBS11 Extron 26-643-06 AV-RCA/6
RCA Composite Video & Stereo Audio, Male-to-Male, 6ft
CVBS12 Extron 26-643-20 AV-RCA/20
RCA Composite Video & Stereo Audio, Male-to-Male, 20ft
Cabling for Audio-Visual Systems
27 1622 - 11
Vega High School Addition Vega Independent School District Cabling for Audio-Visual Systems Schedule of Approved Cable Assemblies & Adapters (cont'd) TYPE MFR PART # MODEL # DESCRIPTION DUBBING CABLES RCA Composite Video + Stereo Audio, Male-to-Male, DUB11 Tecnec N/A 3PG-3PG-3 3ft RCA Composite Video + Stereo Audio, Male-to-Male, DUB12 Tecnec N/A 3PG-3PG-6 6ft RCA Composite Video + Stereo Audio, Male-toDUB13 Tecnec N/A 3PG-3PG-10 Male,10ft RCA Composite Video + Stereo Audio, Male-to-Male, DUB14 Tecnec N/A 3PG-3PG-15 15ft RCA Composite Video + Stereo Audio, Male-to-Male, DUB15 Tecnec N/A 3PG-3PG-25 25ft RCA Composite Video + Stereo Audio, Male-to-Male, DUB16 Tecnec N/A 3PG-3PG-50 50ft RCA Composite Video + Stereo Audio, Male-to-Male, DUB21 Extron 26-643-06 AV-RCA/6 6ft RCA Composite Video + Stereo Audio, Male-to-Male, DUB22 Extron 26-643-20 AV-RCA/20 20ft BNC Composite Video + RCA Stereo Audio, Male-toDUB31 Tecnec N/A G2PB-2PB-3 Male, 3ft BNC Composite Video + RCA Stereo Audio, Male-toDUB32 Tecnec N/A G2PB-2PB-6 Male, 6ft BNC Composite Video + RCA Stereo Audio, Male-toDUB33 Tecnec N/A G2PB-2PB-10 Male, 10ft BNC Composite Video + RCA Stereo Audio, Male-toDUB34 Tecnec N/A G2PB-2PB-15 Male, 15ft BNC Composite Video + RCA Stereo Audio, Male-toDUB35 Tecnec N/A G2PB-2PB-25 Male, 25ft DUB41 Tecnec N/A G2PS-2PS-3 S-Video + RCA Stereo Audio, Male-to-Male, 3ft DUB42 Tecnec N/A G2PS-2PS-6 S-Video + RCA Stereo Audio, Male-to-Male, 6ft DUB43 Tecnec N/A G2PS-2PS-10 S-Video + RCA Stereo Audio, Male-to-Male, 10ft DUB44 Tecnec N/A G2PS-2PS-15 S-Video + RCA Stereo Audio, Male-to-Male, 15ft DUB45 Tecnec N/A G2PS-2PS-25 S-Video + RCA Stereo Audio, Male-to-Male, 25ft
Cabling for Audio-Visual Systems
27 1622 - 12
Vega High School Addition Vega Independent School District S-VIDEO SVID01 SVID02 SVID03 SVID04 SVID05 SVID06 SVID07 SVID08 SVID09 SVID10 SVID11 SVID12 SVID13 SVID14
Tecnec Tecnec Tecnec Tecnec Tecnec Tecnec Tecnec Tecnec Tecnec Tecnec Extron Extron Extron Extron
N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A 26-316-02 26-316-03 26-316-01 26-316-04
Cabling for Audio-Visual Systems
SV4-SV4-1.5 SV4-SV4-3 SV4-SV4-6 SV4-SV4-10 SV4-SV4-15 SV4-SV4-25 SV4-SV4-30 SV4-SV4-50 SV4-SV4-75 SV4-SV4-100 MHR-2-SVM-M/6 MHR-2-SVM-M/12 MHR-2-SVM-M/20 MHR-2-SVM-M/30
4-pin Mini DIN S-Video, Male-to-Male, 1.5ft 4-pin Mini DIN S-Video, Male-to-Male, 3ft 4-pin Mini DIN S-Video, Male-to-Male, 6ft 4-pin Mini DIN S-Video, Male-to-Male, 10ft 4-pin Mini DIN S-Video, Male-to-Male, 15ft 4-pin Mini DIN S-Video, Male-to-Male, 25ft 4-pin Mini DIN S-Video, Male-to-Male, 30ft 4-pin Mini DIN S-Video, Male-to-Male, 50ft 4-pin Mini DIN S-Video, Male-to-Male, 75ft 4-pin Mini DIN S-Video, Male-to-Male, 100ft 4-pin Mini DIN S-Video, Male-to-Male, 6ft 4-pin Mini DIN S-Video, Male-to-Male, 12ft 4-pin Mini DIN S-Video, Male-to-Male, 20ft 4-pin Mini DIN S-Video, Male-to-Male, 30ft
27 1622 - 13
Vega High School Addition Vega Independent School District
Cabling for Audio-Visual Systems Schedule of Approved Cable Assemblies & Adapters (cont'd) TYPE MFR PART # MODEL # DESCRIPTION SVID15 Extron 26-316-05 MHR-2-SVM-M/50 4-pin Mini DIN S-Video, Male-to-Male, 50ft SVID16 Extron 26-316-06 MHR-2-SVM-M/75 4-pin Mini DIN S-Video, Male-to-Male, 75ft SVID17 Extron 26-316-07 MHR-2-SVM-M/100 4-pin Mini DIN S-Video, Male-to-Male, 100ft COMPONENT VIDEO RGB01 Tecnec N/A CV-CV-3 3-RCA Male-to-Male HDTV/Component Video, 3ft RGB02 Tecnec N/A CV-CV-6 3-RCA Male-to-Male HDTV/Component Video, 6ft 3-RCA Male-to-Male HDTV/Component Video, RGB03 Tecnec N/A CV-CV-10 10ft 3-RCA Male-to-Male HDTV/Component Video, RGB04 Tecnec N/A CV-CV-25 25ft 3-RCA Male-to-Male HDTV/Component Video, RGB05 Tecnec N/A CV-CV-50 50ft 3-RCA Male-to-Male HDTV/Component Video, RGB06 Tecnec N/A CV-CV-75 75ft 3-RCA Male-to-Male HDTV/Component Video, RGB07 Tecnec N/A CV-CV-100 100ft RGB11 Extron 26-645-06 HDTV-RCA/6 3-RCA Male-to-Male HDTV/Component Video, 6ft RGBHV RGBHV01 Extron 26-499-01 M59-5-BNC/3 5x BNC Male -to- Male, 24 AWG RG59 Cable, 3ft RGBHV02 Extron 26-499-02 M59-5-BNC/6 5x BNC Male -to- Male, 24 AWG RG59 Cable, 6ft 5x BNC Male -to- Male, 24 AWG RG59 Cable, RGBHV03 Extron 26-499-03 M59-5-BNC/12 12ft 5x BNC Male -to- Male, 24 AWG RG59 Cable, RGBHV04 Extron 26-499-04 M59-5-BNC/25 25ft 5x BNC Male -to- Male, 24 AWG RG59 Cable, RGBHV05 Extron 26-499-12 M59-5-BNC/35 35ft 5x BNC Male -to- Male, 24 AWG RG59 Cable, RGBHV06 Extron 26-499-05 M59-5-BNC/50 50ft 5x BNC Male -to- Male, 24 AWG RG59 Cable, RGBHV07 Extron 26-499-06 M59-5-BNC/75 75ft 5x BNC Male -to- Male, 24 AWG RG59 Cable, RGBHV08 Extron 26-499-07 M59-5-BNC/100 100ft VGA VGA01 Extron 26-238-14 VGA-M-M-MD/3 15-pin HD Mini VGA Male-to-Male, 3ft VGA02 Extron 26-238-01 VGA-M-M-MD/6 15-pin HD Mini VGA Male-to-Male, 6ft VGA03 Extron 26-238-07 VGA-M-M-MD/10 15-pin HD Mini VGA Male-to-Male, 10ft VGA04 Extron 26-238-02 VGA-M-M-MD/15 15-pin HD Mini VGA Male-to-Male, 15ft VGA05 Extron 26-238-03 VGA-M-M-MD/25 15-pin HD Mini VGA Male-to-Male, 25ft VGA06 Extron 26-238-17 VGA-M-M-MD/35 15-pin HD Mini VGA Male-to-Male, 35ft VGA11 Extron 26-112-17 VGA-M-M-MD/3 15-pin HD Mini VGA Male-to-Female, 3ft VGA12 Extron 26-112-15 VGA-M-M-MD/6 15-pin HD Mini VGA Male-to-Female, 6ft VGA13 Extron 26-112-01 VGA-M-M-MD/15 15-pin HD Mini VGA Male-to-Female, 15ft VGA14 Extron 26-112-05 VGA-M-M-MD/25 15-pin HD Mini VGA Male-to-Female, 25ft VGA15 Extron 26-112-28 VGA-M-M-MD/35 15-pin HD Mini VGA Male-to-Female, 35ft NOTE: EQUIVALENT OF ABOVE USING 90-DEG MOLDED CONNECTORS (APPROVED)
Cabling for Audio-Visual Systems
27 1622 - 14
Vega High School Addition Vega Independent School District
Cabling for Audio-Visual Systems Schedule of Approved Cable Assemblies & Adapters (cont'd) TYPE MFR PART # MODEL # DESCRIPTION VGA + STEREO AUDIO 15-pin HD Mini VGA & 3.5mm Stereo Audio MaleVGAA01 Extron 26-490-01 VGA-A-M-M-MD/3 to-Male, 3ft 15-pin HD Mini VGA & 3.5mm Stereo Audio MaleVGAA02 Extron 26-490-02 VGA-A-M-M-MD/6 to-Male, 6ft 15-pin HD Mini VGA & 3.5mm Stereo Audio MaleVGAA03 Extron 26-490-03 VGA-A-M-M-MD/12 to-Male, 12ft 15-pin HD Mini VGA & 3.5mm Stereo Audio MaleVGAA04 Extron 26-490-04 VGA-A-M-M-MD/25 to-Male, 25ft 15-pin HD Mini VGA & 3.5mm Stereo Audio MaleVGAA05 Extron 26-490-07 VGA-A-M-M-MD/35 to-Male, 35ft 15-pin HD Mini VGA & 3.5mm Stereo Audio MaleVGAA06 Extron 26-490-08 VGA-A-M-M-MD/50 to-Male, 50ft DVI DVI01 Extron 26-649-03 DVID-SL-PRO/3 DVI-D Male-to-Male, Single Link, 3ft DVI02 Extron 26-649-06 DVID-SL-PRO/6 DVI-D Male-to-Male, Single Link, 6ft DVI03 Extron 26-649-12 DVID-SL-PRO/12 DVI-D Male-to-Male, Single Link, 12ft DVI04 Extron 26-584-01 IN9700/25 DVI-D Male-to-Male, Single Link, 25ft DVI05 Extron 26-584-02 IN9700/35 DVI-D Male-to-Male, Single Link, 35ft DVI06 Extron 26-584-03 IN9700/50 DVI-D Male-to-Male, Single Link, 50ft DVI11 Extron 26-651-03 DVID-DL-PRO/3 DVI-D Male-to-Male, Dual Link, 3ft DVI12 Extron 26-651-06 DVID-DL-PRO/6 DVI-D Male-to-Male, Dual Link, 6ft DVI13 Extron 26-651-12 DVID-DL-PRO/12 DVI-D Male-to-Male, Dual Link, 12ft HDMI HDMI Male-to-Male, 1.3 Compliant, High Speed, HDMI01 Extron 26-650-03 HDMI-PRO/3 3ft HDMI Male-to-Male, 1.3 Compliant, High Speed, HDMI02 Extron 26-650-06 HDMI-PRO/6 6ft HDMI Male-to-Male, 1.3 Compliant, High Speed, HDMI03 Extron 26-650-12 HDMI-PRO/12 12ft DISPLAYPORT DP01 Extron 26-657-03 DisplayPort-M-M/3 DisplayPort Male-to-Male, 1.1a Compliant 3ft DP02 Extron 26-657-06 DisplayPort-M-M/6 DisplayPort Male-to-Male, 1.1a Compliant 6ft DP03 Extron 26-657-12 DisplayPort-M-M/12 DisplayPort Male-to-Male, 1.1a Compliant 12ft DP04 Extron 26-657-25 DisplayPort-M-M/25 DisplayPort Male-to-Male, 1.1a Compliant 25ft CONTROL CTL01 Extron 26-433-01 232/2 9-pin D RS-232, Male-to-Female, 2ft CTL03 Extron 26-433-03 232/6 9-pin D RS-232, Male-to-Female, 6ft CTL05 Extron 26-433-05 232/10 9-pin D RS-232, Male-to-Female, 10ft CTL06 Extron 26-433-06 232/12 9-pin D RS-232, Male-to-Female, 12ft CTL07 Extron 26-433-07 232/25 9-pin D RS-232, Male-to-Female, 25ft CTL08 Extron 26-433-08 232/50 9-pin D RS-232, Male-to-Female, 50ft
Cabling for Audio-Visual Systems
27 1622 - 15
Vega High School Addition Vega Independent School District
Cabling for Audio-Visual Systems Schedule of Approved Cable Assemblies & Adapters (cont'd) TYPE MFR PART # MODEL # DESCRIPTION ADAPTERS & ADAPTER CABLES Adapter Cable, Stereo Audio, 3.5mm Male -to- RCA ZAU01 Tecnec N/A Y-MPS-2P Male, 6in Adapter Cable, Stereo Audio, 3.5mm Male -to- RCA ZAU02 Tecnec N/A CMR-206 Male, 6ft Adapter Cable, Stereo Audio, 3.5mm Male -to- RCA ZAU03 Extron 26-642-06 TRSM-RCAM-6 Male, 6ft Adapter Cable, Stereo Audio, 3.5mm Male -to- RCA ZAU04 Extron 26-592-01 MSR-6 Female, 6in Adapter Cable, Stereo Audio, Captive Screw -to- RCA ZAU05 Extron 26-575-01 CSR-6 Female, 6in Y-Split Adapter Cable, RCA Male -to- 2x RCA Male, ZAU11 Tecnec N/A Y-P-2P 6in Y-Split Adapter Cable, RCA Male -to- 2x RCA ZAU12 Tecnec N/A Y-P-2PF Female, 6in Y-Split Adapter Cable, RCA Female -to- 2x RCA ZAU12 Tecnec N/A Y-PF-2P Male, 6in Breakout Adapter Cable, Apple iPod Dock Connector ZAU21 Apple N/A MB129LL/B to- RCA Composite Video + RCA Stereo Audio + USB w/ Power Adapter Breakout Adapter Cable, Apple iPod Dock Connector ZAU22 Apple N/A MB128LL/B to- RCA Component Video + RCA Stereo Audio + USB w/ Power Adapter Y-Split Adapter Cable, XLR3 Female -to- 2x XLR3 ZAB01 Tecnec N/A TN-XLF-2XLM-3 Male, 3ft Y-Split Adapter Cable, XLR3 Male -to- 2x XLR3 ZAB02 Tecnec N/A TN-XLM-2XLF-3 Female, 3ft ZAB03 Tecnec N/A BSC3XJSZ Adapter Cable, XLR3 Female -to- 1/4" TRS Male, 3ft Adapter Cable, SPDIF RCA 75ohm -to- AES XLR3-M, ZAD01 Tecnec N/A SPDIF-AES-6 6ft Digital Audio (AES) Impedance Transformer, 110-75 ZAD11 Canare N/A BCJ-XJ-TRB ohm, BNC-F -to- XLR3-F Digital Audio (AES) Impedance Transformer, 110-75 ZAD12 Canare N/A BCJ-XP-TRB ohm, BNC-F -to- XLR3-M ZT01 Extron 100-234-01 T-BNC/10 Termination Plug, BNC 75ohm, Qty(10) Adapter, Composite Video, BNC Female -to- RCA ZV01 Extron 100-226-01 BNCF-RCAM/10 Male , Qty(10) Adapter, Composite Video, RCA Female -to- BNC ZV02 Extron 100-229-01 RCAF-BNCM/10 Male, Qty(10) Adapter, Composite Video, BNC Female -to- Female ZV03 Extron 100-227-01 BNCF-BNCF/10 Barrel Connector, Qty(10) Adapter Cable, Composite Video, RCA Male -to- BNC ZV03 Extron 26-644-06 BNCM-RCAM-6 Male, 6ft Adapter Cable, S-Video, 4-pin Mini DIN Male -to- 2ZS01 Tecnec N/A SV4-2B-6IN BNC Male, 6in Adapter Cable, S-Video, 4-pin Mini DIN Male -to- 2ZS02 Tecnec N/A SV4-2B-3 BNC Male, 3ft
Cabling for Audio-Visual Systems
27 1622 - 16
Vega High School Addition Vega Independent School District
Cabling for Audio-Visual Systems Schedule of Approved Cable Assemblies & Adapters (cont'd) TYPE MFR PART # MODEL # DESCRIPTION Adapter Cable, S-Video, 4-pin Mini DIN Male -to- 2ZS03 Tecnec N/A SV4-2B-6 BNC Male, 6ft Adapter Cable, S-Video, 4-pin Mini DIN Male -to- 2ZS04 Tecnec N/A SV4-2B-10 BNC Male, 10ft Adapter Cable, S-Video, 4-pin Mini DIN Male -to- 2ZS05 Tecnec N/A SV4-2B-15 BNC Male, 15ft Adapter Cable, S-Video, 4-pin Mini DIN Male -to- 2ZS06 Extron 26-353-02 SVHSM-BNCM-1' BNC Male, 1ft Adapter Cable, S-Video, 4-pin Mini DIN Male -to- 2ZS07 Extron 26-353-03 SVHSM-BNCM-3' BNC Male, 3ft Adapter Cable, S-Video, 4-pin Mini DIN Male -to- 2ZS08 Extron 26-353-04 SVHSM-BNCM-6' BNC Male, 6ft Adapter Cable, S-Video, 4-pin Mini DIN Male -to- 2ZS11 Tecnec N/A SV4-2B-6IN BNC Female, 6in Adapter Cable, S-Video, 4-pin Mini DIN Male -to- 2ZS12 Tecnec N/A SV4-2B-6 BNC Female, 6ft Adapter Cable, S-Video, 4-pin Mini DIN Male -to- 2ZS13 Tecnec N/A SV4-2B-15 BNC Female, 15ft Adapter Cable, S-Video, 4-pin Mini DIN Male -to- 2ZS14 Extron 26-353-01 SVHSM-BNCF-8 BNC Female, 8in Adapter Cable, S-Video, 4-pin Mini DIN Male -to- 2ZS15 QVS N/A CSV2RCA10 RCA Male, 10ft Adapter Cable, VGA, 15-pin HD Male -to- 5-BNC ZVGA01 Extron 26-533-01 SYM-BNCM/0.5 Male, 6in Adapter Cable, VGA, 15-pin HD Male -to- 5-BNC ZVGA02 Extron 26-533-11 SYM-BNCM/1 Male, 1ft Adapter Cable, VGA, 15-pin HD Male -to- 5-BNC ZVGA03 Extron 26-533-12 SYM-BNCM/3 Male, 3ft Adapter Cable, VGA, 15-pin HD Male -to- 5-BNC ZVGA04 Extron 26-533-02 SYM-BNCM/6 Male, 6ft Adapter Cable, VGA, 15-pin HD Male -to- 5-BNC ZVGA05 Extron 26-533-03 SYM-BNCM/12 Male, 12ft Adapter Cable, VGA, 15-pin HD Male -to- 5-BNC ZVGA06 Extron 26-533-04 SYM-BNCM/25 Male, 25ft Adapter Cable, VGA, 15-pin HD Male -to- 5-BNC ZVGA07 Extron 26-533-05 SYM-BNCM/50 Male, 50ft Adapter Cable, VGA, 15-pin HD Male -to- 5-BNC ZVGA08 Extron 26-533-06 SYM-BNCM/75 Male, 75ft Adapter Cable, VGA, 15-pin HD Male -to- 5-BNC ZVGA09 Extron 26-533-07 SYM-BNCM/100 Male, 100ft Adapter Cable, VGA, 15-pin HD Male -to- 5-BNC ZVGA11 Extron 26-531-01 SYM-BNCF/0.5 Female, 6in Adapter Cable, VGA, 15-pin HD Male -to- 5-BNC ZVGA12 Extron 26-531-11 SYM-BNCF/1 Female, 1ft Adapter Cable, VGA, 15-pin HD Male -to- 5-BNC ZVGA13 Extron 26-531-12 SYM-BNCF/3 Female, 3ft Adapter Cable, VGA, 15-pin HD Male -to- 5-BNC ZVGA14 Extron 26-531-02 SYM-BNCF/6 Female, 6ft
Cabling for Audio-Visual Systems
27 1622 - 17
Vega High School Addition Vega Independent School District
Cabling for Audio-Visual Systems Schedule of Approved Cable Assemblies & Adapters (cont'd) TYPE MFR PART # MODEL # DESCRIPTION Adapter Cable, VGA, 15-pin HD Male -to- 5-BNC ZVGA15 Extron 26-531-03 SYM-BNCF/12 Female, 12ft Adapter Cable, VGA, 15-pin HD Male -to- 5-BNC ZVGA16 Extron 26-531-04 SYM-BNCF/25 Female, 25ft Adapter Cable, VGA, 15-pin HD Male -to- 5-BNC ZVGA17 Extron 26-531-05 SYM-BNCF/50 Female, 50ft Adapter Cable, VGA, 15-pin HD Male -to- 5-BNC ZVGA18 Extron 26-531-06 SYM-BNCF/75 Female, 75ft Adapter Cable, VGA, 15-pin HD Male -to- 5-BNC ZVGA19 Extron 26-531-07 SYM-BNCF/100 Female, 100ft Adapter Cable Install Kit, Pre-Terminated, VGA 15-pin ZVGA21 Extron 26-511-04 SY-IST/25 HD Male -to- Un-Terminated 5-BNC Female, 25ft Adapter Cable Install Kit, Pre-Terminated, VGA 15-pin ZVGA22 Extron 26-511-05 SY-IST/35 HD Male -to- Un-Terminated 5-BNC Female, 35ft Adapter Cable Install Kit, Pre-Terminated, VGA 15-pin ZVGA23 Extron 26-511-01 SY-IST/50 HD Male -to- Un-Terminated 5-BNC Female, 50ft Adapter Cable Install Kit, Pre-Terminated, VGA 15-pin ZVGA24 Extron 26-511-02 SY-IST/75 HD Male -to- Un-Terminated 5-BNC Female, 75ft Adapter Cable Install Kit, Pre-Terminated, VGA 15-pin ZVGA25 Extron 26-511-03 SY-IST/100 HD Male -to- Un-Terminated 5-BNC Female, 100ft Plenum Adapter Cable Install Kit, Pre-Terminated, VGA ZVGA31 Extron 26-512-04 SY-IST/25 15-pin HD Male -to- Un-Terminated 5-BNC Female, 25ft Plenum Adapter Cable Install Kit, Pre-Terminated, VGA ZVGA32 Extron 26-512-05 SY-IST/35 15-pin HD Male -to- Un-Terminated 5-BNC Female, 35ft Plenum Adapter Cable Install Kit, Pre-Terminated, VGA ZVGA33 Extron 26-512-01 SY-IST/50 15-pin HD Male -to- Un-Terminated 5-BNC Female, 50ft Plenum Adapter Cable Install Kit, Pre-Terminated, VGA ZVGA34 Extron 26-512-02 SY-IST/75 15-pin HD Male -to- Un-Terminated 5-BNC Female, 75ft Plenum Adapter Cable Install Kit, Pre-Terminated, VGA ZVGA35 Extron 26-512-03 SY-IST/100 15-pin HD Male -to- Un-Terminated 5-BNC Female, 100ft Adapter, DVI-A Male -to- VGA 15-pin HD Female, ZDVI01 Extron 26-589-01 DVIAM-VGAF Molded Adapter Cable, DVI-A Male -to- VGA 15-pin HD ZDVI02 Extron 26-619-01 DVIAM-VGAF Female, 6in DVIAMAdapter Cable, DVI-A Male -to- VGA 15-pin HD Male, ZDVI03 Extron 26-540-01 VGAM/6.5 6.5ft ZDVI11 Extron 26-614-01 HDMI-DVI-D/3 Adapter Cable, HDMI Male -to- DVI-D Male, 3ft ZDVI12 Extron 26-614-02 HDMI-DVI-D/6 Adapter Cable, HDMI Male -to- DVI-D Male, 6ft ZDVI13 Extron 26-614-03 HDMI-DVI-D/12 Adapter Cable, HDMI Male -to- DVI-D Male, 12ft ZHD01 Extron 26-617-01 HDMIM-DVIDF Adapter, HDMI Male -to- DVI-D Female, Molded ZHD02 Extron 26-616-01 HDMIF-DVIDM Adapter, HDMI Female -to- DVI-D Male, Molded ZHD03 Extron 26-618-01 HDMIF-DVIDF Adapter, HDMI Female -to- DVI-D Female, Molded ZC01 Extron 70-335-01 CFG-CABLE Adapter Cable, 9-pin D-Sub Female -to- 2.5mm TRS, 6ft [End]
Cabling for Audio-Visual Systems
27 1622 - 18
Vega High School Addition Vega Independent School District
2.4
APPROVED CABLE CONNECTORS
NOTE: Not all cable connectors listed are used in this project. Cabling for Audio-Visual Systems Schedule of Approved Cable Connectors TYPE MFR PART # XLR
MODEL #
Extron, Canare, Switchcraft, Neutrik
DESCRIPTION Line Plugs & Connectors; Bulkhead / Panel-Mount Barrels & Receptacles
TRS Liberty Extron
100-331-01
ACPS-GB-AU 3.5MM-MINI-STEREO-HQ/10
Extron, Canare, Switchcraft, Neutrik
1/4" TRS Male Connector (Qty. 1) 3.5mm TRS Male Connector (Qty. 10) Line Plugs & Connectors; Bulkhead / Panel-Mount Barrels & Receptacles
RCA Extron, Canare, Switchcraft, Neutrik, ADC
Line Plugs & Connectors; Bulkhead / Panel-Mount Barrels & Receptacles
CAPTIVE SCREW Extron
3.5mm Captive Screw Connectors (Pole Qty Varies)
Extron, Canare, Switchcraft, Neutrik, ADC
Line Plugs & Connectors; Bulkhead / Panel-Mount Barrels & Receptacles
Extron, Canare, Switchcraft, Neutrik, ADC
Line Plugs & Connectors; Bulkhead / Panel-Mount Barrels & Receptacles
Canare, ADC
Line Plugs & Connectors; Bulkhead / Panel-Mount Barrels & Receptacles
F-TYPE
BNC
TRIAX
HYBRID FIBER OPTIC (SMPTE 304M) Line Plugs & Connectors; Bulkhead / Panel-Mount Barrels & Receptacles
Canare, ADC, Lemo MINI-DIN Extron
100-330-01
SV-HQ/10
Extron, Switchcraft
4-pin Mini DIN Male Connector (Qty. 10) Line Plugs & Connectors; Bulkhead / Panel-Mount Barrels & Receptacles
FIBER OPTIC Switchcraft, Neutrik, Extron, Crestron
Cabling for Audio-Visual Systems
27 1622 - 19
Vega High School Addition Vega Independent School District
Cabling for Audio-Visual Systems Schedule of Approved Cable Connectors (cont'd) TYPE MFR PART # MODEL # D-SUB Extron 100-066-51 9D-MALE-CONNECTOR/10 Extron 100-067-51 9D-FEMALE-CONNECTOR/10 Extron
100-070-51
15HD-MALE-CONNECTOR/10
Extron
100-071-51
15HD-FEMALE-CONNECTOR/10
TecNec
DP25B
TecNec
DJ25B
TecNec
DE25B
TecNec
DZ25B
Extron, Switchcraft, Neutrik Extron USB, FIREWIRE, PS/2 Switchcraft, Neutrik, Quiktron/Cables To Go LOUDSPEAKER (SPEAKON, HPC, BANANA) Switchcraft, Neutrik IMPEDANCE MATCHING TRANSFORMERS Canare, Switchcraft, Neutrik, ADC, Whirlwind
DESCRIPTION 9-pin (DE9) Connector, Male (Qty. 10) 9-pin (DE9) Connector, Female (Qty. 10) 15-pin (DE9) HD15 Connector, Male (Qty. 10) 15-pin (DE9) HD15 Connector, Female (Qty. 10) 25-pin (DB25) Connector Body, Male (Qty. 1) 25-pin (DB25) Connector Body, Female (Qty. 1) Plastic Hood for 25-pin (DB25) Connector, Gray Color (Qty. 1) Metal Hood for 25-pin (DB25) Connector, Die-Cast Zinc Alloy (Qty. 1) Line Plugs & Connectors; Bulkhead / Panel-Mount Barrels & Receptacles Gender Changers
[End]
Cabling for Audio-Visual Systems
27 1622 - 20
Vega High School Addition Vega Independent School District
PART 3 - EXECUTION
3.1
STANDARDS A.
All cabling and termination shall be executed in adherence to standard industry practices such as those outlined in the following: 1. 2. 3. 4.
3.2
NECA 1, Good Workmanship in Electrical Contracting Philip Giddings, Audio Systems Design and Installation. Boston: Focal Press, 1990. Kenneth T. Deschler, Cable System Design and Installation. McGraw-Hill, Inc. 1987. InfoComm International, AV Installation Handbook – Second Edition: The Best Practices for Quality Audiovisual Systems. InfoComm International, 2007. Fairfax, VA
EXAMINATION A.
Site Verification of Conditions: 1. 2. 3.
3.3
Verify that conditions of substrates and pathways previously installed under other sections or contracts are acceptable with cable installation. Inform Owner of unacceptable conditions immediately upon discovery. Proceed with installation only after unacceptable conditions have been corrected.
CABLE LENGTHS A.
3.4
Cable Length Verification: Cable lengths where given in the Specification, for bulk or manufactured cable assemblies, have been provided to assist the Contractor in the bidding process. Cable run lengths, where specified, are end-point-to-end-point estimates and include consideration for tails. Estimates may be based upon cable tray systems; raceways, conduit runs, and furniture layouts indicated on construction drawings and may vary from the actual installed cable pathways. It is responsibility of the Contractor to field verify required cable lengths for bulk cable or manufactured cable assemblies prior to ordering.
INSTALLATION A.
Non-contiguous cable support mechanisms such as hangers, rings, and hooks shall not be spaced farther than four (4) feet apart. All manufactured raceways used for cables shall be installed according to the raceway manufacturer’s specifications.
B.
Cable runs shall be supported with devices designed for this purpose and are to be installed independent of any other structural component.
C.
Cables routed vertically up walls, or between floors as vertical riser, shall be supported with clamps or other mechanisms. These supports shall occur at least three times per floor.
D.
Cable pulling tension may not exceed manufacturer recommendations. Where cable-pulling lubricant is used, the lubricant must be compatible (non-damaging) with the conduit and cable sleeve materials and must not harden over time to prevent future pulls.
E.
Cable stapling of any recognized media type shall not be permitted.
Cabling for Audio-Visual Systems
27 1622 - 21
Vega High School Addition Vega Independent School District
F.
Cables shall be dressed in conveniently sized bundles and either laced or banded. Lacing or banding shall not be so tight as to deform cable bundles.
G.
Cabling installed with a bend radius less than that recommended by the cabling manufacturer is not acceptable.
H.
Cables and bundles terminating at equipment or connector panels shall be supported so as not to put strain on connections or connectors.
I.
All cables, with the exception of video or pulse cables, which must be cut to an electrical length, shall be cut to the length dictated by the run. No splices shall be permitted in any pull boxes without prior approval of the Consultant.
J.
Cabling for equipment mounted in drawers or on slides shall be provided with a service loop of appropriate length. A cable management support for the service loop shall be provided to prevent the service loop travel from interfering with the operation of the drawer or slide, or snagging on adjacent cabling.
K.
Install wiring in raceway and cable tray except within consoles, cabinets, desks, and counters. Conceal raceway and wiring except in unfinished spaces.
L.
Microphone level, line level, loudspeaker level, and video lines shall all be run in separate conduits, trough, raceway divider, and cable bundles. Low voltage DC and control may be run along with any but microphone- or line- level audio cable runs.
M.
Use NRTL-listed plenum cable in environmental air spaces, including plenum ceilings. Conceal raceway and cables except in unfinished spaces.
N.
Install LAN cables using techniques, practices, and methods that are consistent with Category 5E/6 rating of components and that ensure Category 5E/6 performance of completed and linked signal paths, end to end.
O.
Install cables without damaging conductors, shield, or jacket.
P.
Repair damage to adjacent materials caused by cable work.
3.5
TERMINATION A.
Contractor to follow approved Manufacturer procedures for termination instructions for the specific products being installed.
B.
All termination components must meet or exceed all specifications for given media type and application as described in this document and system drawings.
C.
Crimp on connectors shall be installed only on the appropriate size cable using the manufacturer recommended crimp tool and die set.
D.
Connections to electronic devices providing screw terminals shall be terminated using the appropriate gauge insulated spade or ring crimp terminal connector and crimp tool.
Cabling for Audio-Visual Systems
27 1622 - 22
Vega High School Addition Vega Independent School District
E.
All mechanical solder-on connectors shall be attached to cable ends using rosin core solder.
F.
Audio signal cable shields shall be protected with the appropriate gauge Teflon or heat-shrinkable tubing. The jacket end of each audio cable shall be fitted with the appropriate gauge heat shrinkable tubing to provide additional protection to the base of the shield or shield foil. This also applies to the inside of mechanical connectors and cables that terminate at partitioned barrier strips.
3.6
GROUNDING A.
Comply with Division 26 requirements for grounding and bonding for electrical systems.
B.
Comply with IEEE 1100, "Power and Grounding Sensitive Electronic Equipment."
C.
Ground cable shields, drain conductors, and equipment to eliminate shock hazard and to minimize ground loops, common-mode returns, noise pickup, cross talk, and other impairments.
D.
Bond shields and drain conductors to ground at only one point in each circuit.
3.7
IDENTIFICATION A.
In addition to requirements in this Article, comply with applicable requirements in Division 26 requirements for identification for electrical systems and with TIA/EIA-606.
B.
Labeling: 1. 2.
3.
4.
5.
6.
Label products in a logical, legible and permanent manner corresponding to the Drawings. Wording, format, style, color and arrangement of text will be subject to the Architect’s approval. Label all wall plates for input, output and control receptacles as well as connector mounting plates in floor boxes using 1/8” engraved lettering filled with black paint if plate is light colored and filled with white paint if plate is dark colored. Provide engraved labels similar to Lamicoid, Traffolyte or equal and approved, squarely and permanently attached to label patch panels, barrier strips, terminals, transformers, switches, relays and similar devices as well as front and rear of all signal processing equipment (e.g. PA, LIM, EQ). Label all controls on distribution amplifiers, mixers, etc. as to the function of each. Label all permanent wiring on both ends with approved permanent clip-on type or sleeve type markers. Wrap-around adhesive labels will not be accepted unless completely covered with clear heat shrink tubing. Label all portable equipment with permanent labels showing ownership by Owner. Label all portable cables similarly with printed heat-shrinkable tags located 12 inches from the male connector end. Use 1/8” block letters and verify acceptability of wording with the A/V Design Consultant prior to engraving or printing labels. Sample labels: (DVD Wire End) CABLE # A107 DVD-1 AUDIO IN L ROUTER AUDIO OUT 12L
C.
(Router Wire End) CABLE # A107 ROUTER AUDIO OUT 12L DVD-1 AUDIO IN L
At completion, all cabling labels and schedules shall reflect as-built conditions.
Cabling for Audio-Visual Systems
27 1622 - 23
Vega High School Addition Vega Independent School District
3.8
CLEANING A.
Upon completion, remove surplus materials, trash, tools and equipment.
END OF SECTION
Cabling for Audio-Visual Systems
27 1622 - 24
Vega High School Addition Vega Independent School District
SECTION 27 4100 - AUDIO-VISUAL SYSTEMS
PART 1 - GENERAL
1.1
RELATED DOCUMENTS A.
1.2
Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to this Section.
SCOPE OF WORK A.
Work covered by this Section shall consist of furnishing labor, equipment, supplies, materials, and testing unless otherwise specified, and in performing the following operations recognized as necessary for the installation, termination, testing and labeling of all telecommunications infrastructure as described on the Drawings and/or required by these specifications. 1. 2. 3. 4. 5.
1.3
Furnishing equipment, cabling, supplies, and materials Furnishing labor for installation, testing, software programming, and user training. Third party testing and commissioning Service and maintenance contract All other operations that are not explicitly described herein but are necessary for a complete functioning system which shall adhere to the performance parameters as described on the drawings and/or required by these specifications.
Related Sections: The following Sections contain requirements that relate to this Section. 1. 2.
1.4
Division 26, Section 26 0500 “Common Work Results for Electrical”: Power supply, conduit and wiring. Division 27, Section 27 1622, Cabling for Audio-Visual Systems.
REFERENCES A.
Underwriters Laboratories Inc. (UL)
B.
International Code Council (ICC): 1.
1.5
International Building Code, 2009 Edition as adopted by State of New Mexico 2009 Commercial Building Code.
DEFINITIONS A.
Terms: 1. 2. 3.
4. 5.
Bidder: Entity generating the bid response. Contractor: Successful Bidder to whom the Owner has awarded the contract. Installer (a.k.a. “Audiovisual Systems Integrator” or similar): Actual entity providing the audiovisual systems installation. Generally equivalent to “Contractor” or else a sub-contractor hired by the Contractor. Furnish: Indicates the responsibility to ship or deliver the item to the job site, freight prepaid, for receipt, staging and installation by others. Install or Installation: Indicates the responsibility of receiving the item at the job site, providing adequate storage, unpacking or uncrating the item, physically securing the item or otherwise
Audio Visual Systems
27 4100 - 1
Vega High School Addition Vega Independent School District
6. 7.
making ready the item for its intended use by following the instructions and approved methods of the manufacturer and those contained herein. Provide: Indicates the responsibility to both “Furnish” and “Install.” Installation Materials: Shall refer to installed materials which may or may not be explicitly specified herein, but which are essential to a complete functioning system such as the following: a.
b. c.
d. 8. 9.
10. 11.
NIC or Not In Contract: Equivalent to “Provided by Others”. OFCI or Owner Furnished Contractor Installed: Shall refer to equipment that will be furnished by the Owner for installation by the Contractor. The Contractor shall be responsible for installing and integrating this equipment as detailed herein. The term “shall” is mandatory; the term “will” is informative; and the term “should” is advisory. Format or Aspect Ratio: Proportion of image area expressed as a ratio of width/height. a. b. c.
B.
Concealed cabling, exposed and/or loose cabling, cable terminations, cable adapters, cable management, cable labeling, cable dressing, and patch cords (voice, data, audio and/or video) Custom connection panels and/or blank cover panels for rough-in devices (wall boxes, floor boxes, ceiling boxes, cubbies) or rack-mounted termination/patch fields. Equipment rack fit-out accessories: Ganging hardware, leveling feet, floor anchors, raised floor pedestals, riser bases, caster bases, doors, locks, side panels, rear panels, top panels, vent blockers, ventilation fans, thermostats, power distribution strips, grounding lugs, grounding bus bars, vertical & horizontal cable lacing bars, rack and/or equipment labels, rack shelves, rack mounts, rack storage drawers, security rack panels, blank rack panels, and rack header identification panels. Any unmentioned materials as needed to install the systems defined herein.
4:3 or “NTSC” or “SD” or “SDTV” or “Legacy Video” Format: 1.33:1. 16:9 or “HD” or “HDTV” Wide Format: 1.78:1. 16:10 or “Computer” Wide Format: 1.60:1.
Acronyms: 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17.
ADA: Americans with Disabilities Act ALS: Assistive Listening System intended for persons with hearing disabilities AV: Audio-Video or Audio-Visual BGM: Background Music CATV: Community Access Television (aka “cable television”) CPU: Central Processing Unit DSP: Digital Signal Processor DVD: Digital Video Disc or Digital Versatile Disc. This acronym refers to the standard optical disc format for playback of audiovisual and/or multi-media. FPD: Flat Panel Display FM: Frequency Modulation. Also refers to the electromagnetic band of frequencies between 88 – 108 MHz used for radio broadcasting within the United States. IP: Internet Protocol IR: Infrared IT: Information Technology LAN: Local Area Network LCD: Liquid Crystal Display, a type of flat panel display MATV: Master Antenna Television PC: Personal Computer. This acronym applies to stationary “tower” or “desktop” workstations, in addition to portable “notebook” or “laptop” computers.
Audio Visual Systems
27 4100 - 2
Vega High School Addition Vega Independent School District
18. 19. 20. 21. 22. 23. 24. 25. 26. 27.
1.6
PDP: Plasma Display Panel, a type of flat panel display RF: Radio Frequency TO: Telecommunications Outlet – contains one or more service drops for data/voice systems. TV: Television UHF: Ultra High Frequency band of electromagnetic waves, currently 470 – 806 MHz for television broadcasting within the United States. UPS: Uninterruptible Power Supply. USB: Universal Serial Bus, a serial bus standard to interface data devices. VHF: Very High Frequency band of electromagnetic waves, currently 55 – 88 MHz for television broadcasting within the United States. VHS: Video Home System. This acronym refers to the standard consumer-grade video cassette format for playback of audiovisual media. WAN: Wide Area Network.
SYSTEM NARRATIVE
A.
Gymnasium – A/V System Type “A”: The Gymnasium shall employ a built-in sound reinforcement system consisting of: 1. 2.
3.
4. 5. 6.
7.
Sound reinforcement system shall be designed around an audio Digital Signal Processor (DSP). Various loudspeakers shall be provided with configurations and locations selected to ensure even audio coverage of both the bleacher seating areas and the playing court with good intelligibility for reproduced speech and program content as well as adequate undistorted headroom to overcome typical crowd noise at high school level sporting events. Two primary types of loudspeakers will be used in this system: a. Ceiling-hung full-range loudspeaker cabinets with low-frequency response extending to below 100 Hz. These loudspeakers will provide directed coverage of the bleacher seating areas. b. Full-range coaxial ceiling speakers designed for high-ceiling applications installed in surface-mount enclosures/baffles. These loudspeakers shall be attached to the structural ceiling deck in an arrangement which provides even coverage of the playing court area. Provide (4) wireless microphone systems each with (1) hand-held transmitter and (1) beltpack transmitter with lapel microphone. Provide antenna combiner and remote mount antennas in Gym area. Provide microphone/line level input connections at multiple locations throughout the Gym area connected back to the rack mounted sound system. Provide rack mounted A/V control panel at the A/V equipment rack. Provide wall-mounted cabinet-style A/V equipment rack in adjacent storage room. Rack will include the following: a. Extra capacity (mounting space, power distribution, and thermal control) for future Owner provided equipment. b. Power distribution system with power conditioning. c. Forced air ventilation with thermally controlled fans. d. Locking storage drawers. e. Vented locking front door. f. Wire management hardware. g. Blank or vented covers over all empty rack spaces. Complete FM Assistive Listening System (ALS) to meet ADA Code: a. FM ALS Transmitter installed in the A/V equipment rack. b. Extend antenna from rack to Gym area. c. Provide receivers and inductive neck loops per ADA code. Provide: (1) Transmitter, (Qty 28) Receivers, and (Qty 7) Inductive Neck Loops. d. Receivers and accessories to be stored in locking storage case.
Audio Visual Systems
27 4100 - 3
Vega High School Addition Vega Independent School District
1.7
DESIGN PRINCIPLES A.
Flexibility: The facility’s cable pathway infrastructure (utilized for audiovisual signals, as well as relevant data/voice and AC power signals) shall be sufficiently flexible to allow future expansion of the audiovisual systems. Design parameters for such expansion are in accordance with the Owner’s long-term goals and expectations for such systems, as outlined within this section.
B.
Cost Effectiveness: The AV systems shall utilize limited resources with utmost efficiency. Emphasis lies on common usability and current technology standards, and not on emerging technology trends or enhanced features.
C.
Ease of Operation: The AV systems shall require a minimal amount of Owner training for successful operation. User interfaces (control panels, signal connection panels, etc.) shall have a consistent look and feel throughout the facility.
D.
Sustainability: The AV systems shall be designed with a high degree of reliability in mind. Operation of such systems shall require minimal ongoing maintenance, as well as minimal investment by the Owner in dedicated support personnel. It is recommended that the Owner establish an agreement with the AV systems integrator, to secure warranty service calls and/or ongoing maintenance support.
E.
Network Connectivity: With the convergence of audiovisual and information technologies, careful planning must occur to ensure that network connectivity is provided for IP-enabled audiovisual devices and systems. Telecommunications outlets and their port quantities must be coordinated to meet or exceed the requirements of the appropriate audiovisual equipment. Discussion with the Owner’s IT staff/entity will be required to ensure proper coordination between the audiovisual systems and the network design.
1.8
PERFORMANCE REQUIREMENTS A.
All Audiovisual Systems shall interface and be compatible with each other.
B.
Audio 1. 2.
Polarity: Absolute signal polarity will be maintained throughout the signal chain such that a positive signal at the input produces a corresponding positive excursion at the loudspeakers. Electronics: The audio system electronics shall deliver the following minimum performance standards as measured from all source inputs for microphones, disc and/or cassette playback devices, etc., through all mixers, audio distribution amplifiers, routers, etc., to all audio signal destinations. a. b. c.
3.
Frequency Response: +/- 0.5dB, 20-20,000 Hz Hum and Noise: -70 dBu, 20-20,000 Hz, un-weighted Distortion: 0.1% THD, 20-20,000 Hz
Speech Signal: The system shall provide a speech signal in the audience seating area that meets the following requirements: a. b. c. d.
Audio Visual Systems
Frequency response within +/- 3 dB from 500 Hz to 15,000 Hz. Overall SPL variance of +/- 3 dB. Measured percentage articulation loss of consonants (Alcons) of 10% or lower. Maximum average SPL of 97 dB (flat), with 10 dB of undistorted headroom available.
27 4100 - 4
Vega High School Addition Vega Independent School District
1.9
SUBMITTALS A.
Product Data: For all proposed equipment, cables and connectors, and faceplates for evaluation of technical features. Reference each product to a location on Drawings. Include the following: 1. 2. 3. 4. 5.
B.
Shop Drawings: The shop drawings listed below are required of the Contractor. Submit all Shop Drawings complete as a single submission. Isolated items will not be accepted, except with prior approval. 1. 2.
3. 4. 5. 6. 7. 8. 9.
10.
11.
C.
Manufacturer’s submittal sheet (if applicable). Manufacturer’s published specification “cut” sheets. Operating characteristics, furnished specialties, and accessories. Physical data (dimensions, weight, line art and/or photos). Test and evaluation data (frequency and phase plots at on-axis and multiple off-axis incidence angles, impedance plot, 1/3-octave polar coverage patterns, etc.)
System Narrative: Concise narrative description of the system’s performance capabilities, physical connection topology, and sequence of operation for each different “scene” or “mode”. Schematic: Detailed wiring diagrams showing interconnection of components and products, wiring and cabling diagrams depicting cable types and designators, and device designators. Provide connector designations and terminal strip identification, along with color codes for cables connecting to these devices. Give each component a unique designator and use this designator consistently throughout the project. Diagrams for cable management system – e.g., inside equipment racks, in cable tray, etc. Cabling Schedule: A list containing the cable type, cable marker identifier, and origination and destination location and connector types for each cable. Mounting Details for Loudspeakers: Scaled drawings of complete mounting details, hardware and support surfaces, including details on all load requirements, safety factors, and structural materials. Panels: Scaled drawings of interconnect panels. Equipment & Panel Labels: A list containing the identifier label for all panels and rack mounted equipment. Include information on label type and construction. Equipment Rack Layouts: Fully detailed rack drawings (rack front elevations) indicating equipment orientation within the equipment rack. DSP Functional Diagrams: Complete functional diagrams of all DSP programming and configurations. These diagrams shall utilize functional blocks to graphically depict the routing and processing applied to an audio signal as it passes through the DSP. Cable Routing / Riser Diagram: Diagram showing conduits/pathways for audio and control cabling with clear indications of which cables will be installed in each pathway. Cabling installed in each pathway may be called out via tags on the diagram or via cable run schedule(s) included with the diagram. All cable runs shall be identified with cable ID tags which match those shown on the signal flow diagram described above. The Consultant’s details, diagrams, elevations, and section views from the project documents in electronic format (i.e. CAD/BIM files) will not be supplied to the Contractor for their use as part of submittals. The Consultant’s plan views (i.e. floor plans, reflected ceiling plans, etc.) from the project documents in electronic format may be supplied to the Contractor for their use as part of submittals upon written request with completion of associated indemnity agreements.
Calculations: 1. 2.
Loudspeaker Cabling: Provide calculations for loudspeaker cable sizing based on load impedance, voltage drop, and damping factors. Output Limiters: Provide calculations for proper output compressor/limiter settings in DSP units to prevent loudspeaker damage.
Audio Visual Systems
27 4100 - 5
Vega High School Addition Vega Independent School District
D.
Project planning documents as specified in Part 3.
E.
Product Samples – To be provided upon request only: 1. 2. 3. 4. 5.
F.
Field quality-control test reports: For speech and program audio amplification systems identified herein to ensure proper speech intelligibility, gain-before-feedback, loudness and coverage uniformity under typical operating circumstances. 1. 2. 3. 4.
G.
2. 3. 4. 5. 6. 7.
A.
Measured ambient noise levels with all normal systems operating (HVAC, lighting, etc) and with all components of sound reinforcement system powered on without any amplified signal. Measured electrical impedance for all loudspeaker channels. Plots of system Reverberation Time (RT) measurements. Plots of system Sound Pressure Level (SPL) histograms.
Equipment Rack Identification Panel: 1.
1.10
Cabling and connectors – typical for each type Cable marking samples: As described in Section 27 1622. Equipment labels Connection panel / faceplate with etched engraving Equipment rack identification panel – refer to paragraph (G) below.
Within each room containing equipment racks for audio-visual systems, a custom graphical identification panel shall be installed within one (1) of the equipment rack(s) in that room. All equipment rack identification panels in the facility shall be identical. Submit preliminary graphical layout of this panel to the Architect / Engineer for review, included on a CD-ROM using a common digital image format such as JPEG, GIF, TIFF or Bitmap. The panel design shall include the following – no exceptions: Installer’s name and contact information Design Engineer’s name and contact information Owner’s name and a brief description/identifier of the project or system type. The panel shall be mounted in the top rack space unless otherwise indicated on the Drawings.
CLOSEOUT DOCUMENTATION Operation and Maintenance Data: Complete operating instructions and features available. In addition to items specified in Division 01 Section "Operation and Maintenance Data" include the following: 1. 2.
3. 4. 5. 6. 7.
Equipment documentation and instructions. Operating documentation, manuals, and software for equipment and all installed peripherals and features. Software shall include system restore, emergency boot diskettes, and drivers for all installed hardware. Hard copies of manufacturer's specification sheets, operating specifications, design guides, user's guides for software and hardware System installation and setup guides, with data forms to plan and record options and setup decisions. Quick-reference guides for the installed systems. This includes both touchpanel and general system quick-reference guides. Two (2) CD-ROM/DVD-ROMs with electronic copies of all submittal items listed above. CD/DVDs will contain bookmarked PDF files, easily searchable by owner. PDF files on CD-ROM of all submittal items listed above.
B.
PDF files on CD-ROM with serial numbers for equipment. List to include the associated manufacturer/ model number and the location of the equipment
C.
As-built shop drawings.
Audio Visual Systems
27 4100 - 6
Vega High School Addition Vega Independent School District
1.11 A.
QUALITY ASSURANCE Installer Qualifications: As part of the Bid Response and Submittal Documents, the Contractor shall furnish evidence of his/her qualifications to perform the work specified. Evidence of Contractor qualifications shall include the following: 1.
2.
3. 4.
The Bidder shall clearly identify project team members (Installers) pertaining to the installation of AV systems. Team members to be identified shall be Principal, Project Manager, Chief Engineer, Senior Field Technician, and Software Programmer. The documentation shall include the individual’s name, years with firm, and brief resume of the employee’s past projects. Resumes shall include a listing of years of experience and any special training, certification by trade associations, and any applicable certification documentation for the proposed system. Due to the complexity of the control & automation system, a manufacturer-certified software programmer shall be required to author the programming component of this project. The Contractor shall include in the Bid Response, the name and office location of the manufacturer certified person or entity that will provide programming for the remote control system. The resume shall include a listing of years of experience and include a statement of manufacturer authorization, certification, and qualification. A list of equipment manufacturer product lines, relevant to the project, for which the Contractor is authorized as a Distributor, Dealer, and Installer. A list of equipment manufacturer product lines, relevant to the project, for which the Contractor is authorized to provide warranty repair service.
B.
All provided Installer and Programmer Qualifications (listed above) shall be current and valid at the time of bidding. For example, the Contractor shall not list a product manufacturer or line for which he/she is not a dealer on the bid due date, but for which he/she hopes or intends to become a dealer in the future.
C.
Source Limitations: Obtain common materials and equipment through one source from a single manufacturer as much as practical.
D.
All equipment for this installation shall be new (packaged in the manufacturer’s original packaging), less than one year from the date of manufacture, and without blemish or defect.
E.
The Contractor shall maintain the same project manager and field supervisor throughout the installation, and will maintain the same installers.
F.
The Contractor shall supply and install any incidental equipment needed in order to result in a complete and operable system without claim for additional payment, even if such equipment is not listed in this Specification.
G.
All work related to this Specification shall be completed in a professional manner by fully qualified workers.
H.
Reliability: The systems shall be designed to provide professional quality operation over a period of several years without the need for continual maintenance. Equipment that has a high failure rate is not acceptable for installation as part of these systems.
I.
Pre-installation meeting: Conduct pre-installation meeting with other trades to: 1. 2. 3.
Verify project requirements and manufacturers’ instructions Coordinate environmental conditioning of the space (temperature & humidity) Coordinate elements attaching to, penetrating through, or concealed above/behind work in this section.
Audio Visual Systems
27 4100 - 7
Vega High School Addition Vega Independent School District
J.
Electrical Components, Devices, and Accessories: Listed and labeled as defined in NFPA 70, Article 100, by a testing agency acceptable to authorities having jurisdiction, and marked for intended use.
K.
Comply with NFPA 70, "National Electrical Code."
1.12 A.
DELIVERY, STORAGE, AND HANDLING Equipment, Cabling and Installation Materials: 1.
2.
3. 4.
5. 6.
Costs of all shipping to the site, and of all unusual storage requirements, shall be borne by the Contractor. It shall be the responsibility of the Contractor to make appropriate arrangements, and to coordinate with the authorized personnel at the site, for the proper acceptance, handling, protections, and storage of equipment so delivered. Store in temperature- and humidity-controlled environment in original manufacturer's sealed containers. Maintain ambient temperature between 50 and 85 deg F (10 and 30 deg C), and not more than 80 percent relative humidity, non-condensing. Open each container; verify contents against packing list, and file copy of packing list, complete with container identification for inclusion in operation and maintenance data. Mark packing list with designations that have been assigned to materials and equipment for recording in the system labeling schedules that are generated by cable and asset management system specified in Part 2. Save original manufacturer's containers and packing materials and deliver as directed under provisions covering extra materials. Waste Management and Disposal: Separate waste materials for recycling in accordance with Division 01, Section “Construction Waste Management and Disposal”. a. b. c.
1.13
Remove packaging materials from site and dispose of at appropriate recycling facilities. Collect and separate for disposal paper, plastic, corrugated cardboard and/or polystyrene packaging materials in appropriate onsite bins for recycling. Dispose of all non-recyclable packaging materials and debris in a safe and environmentally responsible manner according to the instructions set forth by the General Contractor, local ordinances or codes and the Environmental Protection Agency.
PROJECT CONDITIONS
A.
Environmental Conditions: System shall be capable of withstanding the following environmental conditions without mechanical or electrical damage or degradation of operating capability.
B.
Interior, Controlled Environment: System components installed in temperature-controlled interior environments shall be rated for continuous operation in ambient conditions of 36 to 122 deg F (2 to 50 deg C) and 20 to 90 percent relative humidity.
1.14
WARRANTY
A.
Project Warranty: Refer to Contract Conditions for project warranty provisions.
B.
Manufacturer Warranties: Submit to Owner or Owner’s Representative all written and dated warranties, in addition to completed product support registration cards, as issued by product manufacturers warranting all individual components against defects in materials or manufacturing, for the periods established by said manufacturers. The start date of the warranties shall be the date of final system acceptance.
Audio Visual Systems
27 4100 - 8
Vega High School Addition Vega Independent School District
C.
System Warranty: The Bidding Contractor or sub-contractor (Installer) shall make known, in writing, at time of Bid any exceptions that might exist between conditions described herein and Installer’s policy of warranty. After acceptance of bid, all conditions and requirements of warranty described herein shall apply. 1. 2.
3. 4.
5.
6.
7.
8.
9.
1.15
The Installer shall guarantee all provided equipment, materials, and labor for a period of 1 year from the date of final acceptance. Equipment that the Installer does not provide as part of this contract is exempt from this warranty coverage. However, the installation labor and materials associated with any equipment installed by the Installer, including OFCI items, shall be covered under this warranty. During the warranty period, within 24 hours of notification, the Installer shall answer all service calls and requests for information. During the warranty period, within 72 hours of original notification, the Installer shall provide emergency service to restore operation of the system, replacing defective materials, repairing faulty workmanship, making temporary repairs, and providing loaner equipment as necessary, all at no charge. The Installer shall notify the Owner after any service call whether such call is or is not covered under the warranty. The Owner may be billed for non-warranty calls. The Installer shall notify the Owner of any service call or work to be performed for which charges may be incurred before such work commences. Improper functioning, for warranty purposes, means failure of the system to meet the intentions of the specification because of internal defects. It does not include Owner-caused malfunctions such as re-adjustment of the controls, re-tuning of the system, or injury to the system beyond normal wear. Nor does the warranty cover paint, exterior finishes, fuses, lamps (including projection lamps) or associated labor, unless the damage or failure results from defective materials or workmanship covered by the warranty. The Installer shall take such actions at the time of installation to ensure that all equipment is installed in accordance with the manufacturer recommended environmental and electrical operating conditions and requirements. After installation, the Installer shall be responsible for the repair or replacement of said equipment that the Installer provided which fails due to environmental or electrical conditions, even if not covered by the manufacturer’s warranty. The Installer shall not be held responsible for damages due to changes in environmental conditions which occur after system acceptance. If the Installer has modified certain components, the manufacturer’s warranty for such components may become void. In such a case, the Installer is responsible for providing warranty coverage equal to that originally provided by the manufacturer. Certain subsystems and system components may require installation by authorized representatives in order for the complete manufacturer warranty to apply. If this pertains to any subsystem or component for this project, it is the Installer’s responsibility to make arrangements for the complete manufacturer warranty to apply. These arrangements are to be made at no additional cost to the Owner.
SERVICE CONTRACT
A.
As part of this Specification, the Contractor shall initiate a one-year service contract to commence on the date of final acceptance and continue to the first anniversary of the date of final acceptance as defined in ‘System Acceptance’. The scope of the service contract would normally extend beyond warranty service calls, to include ongoing support of the AV systems such as maintenance, periodic replacement of consumables, Owner training or assistance, and/or additional design-build agreements.
B.
As part of the Bid Response, the Contractor shall provide the Owner with a proposal for continuation of the service contract to include Year Two, Year Three and Year Four of operation. All terms and conditions of the Year One Warranty shall apply.
Audio Visual Systems
27 4100 - 9
Vega High School Addition Vega Independent School District
1.16 A.
PRIOR APPROVAL For substitutions of products specified herein, Contractor shall submit requests for prior approval at least 10 days prior to submitting bids, and in accordance with the provisions of Bidding Instructions and/or Division 1.
PART 2 - PRODUCTS
2.1
GENERAL A.
Provide products quantities as required. If a quantity is given, provide at least the given amount.
B.
Products shall be new, free from defects and listed by UL when an applicable UL Standard exists. Provide Products of a given type from one manufacturer.
C.
Regardless of the length or completeness of the descriptive paragraph under article titled “Manufacturers and Products”, provide Products complying with the specified manufacturer's published specifications.
D.
Take care during installation to prevent scratches, dents, chips, etc.
2.2
MANUFACTURERS AND PRODUCTS A.
If a specified product has been discontinued by a manufacturer, provide the replacement model (as certified by the manufacturer) at no additional cost.
B.
Where required provide manufacturer’s rack mount adapter or one manufactured by Middle Atlantic or Winsted.
C.
Provide complete and fully functional systems, including items that are not explicitly described herein, but are necessary for a complete functioning system which shall adhere to the performance parameters as described on the drawings and/or required by these specifications. Items shall include, but are not limited to, all required mounting hardware and faceplates.
2.3
SOFTWARE A.
All commercial software used, shall be registered to Owner, in Owner’s name. Owner to be supplied with all software documentation including copies of software registration.
B.
Contractor shall load and test the required software on an Owner furnished computer and load and test all required updates to A/V control panels. If desired by Owner, provide a complete and fully functional network management system.
C.
Coordinate all required management, control and monitoring functions with the Owner. If network management is desired by the Owner, minimum requirements shall include: 1. 2.
Event scheduling System control of individual systems
Audio Visual Systems
27 4100 - 10
Vega High School Addition Vega Independent School District
2.4
GYMNASIUM SOUND SYSTEM A.
Provide product makes and models as listed in APPENDIX A attached to the end of this Section. 1.
2.5
Provide complete and fully functional systems, including items that are not explicitly described herein, but are necessary for a complete functioning system which shall adhere to the performance parameters as described on the drawings and/or required by these specifications. Items shall include, but are not limited to, all required mounting hardware and faceplates.
CABLING A.
2.6
Refer to Section 27 1622, Cabling for Audio-Visual Systems as well as APPENDIX A attached to the end of this Section.
PRODUCT SUBSTITUTIONS A.
Refer to “Prior Approval” in Part 1 of this document.
B.
The materials and products specified herein reflect the minimum acceptable standards of fabrication and manufacture. All materials and products supplied by the Contractor and specified herein are to be new, unused, of first quality and in original packaging or shipping containers or as shown on drawings.
C.
The products listed herein are pre-approved for this project. Substitutions shall be permitted for the manufacturers and products contained herein, provided they equal or exceed the specifications thereof and are approved via formal request.
2.7
SCHEDULE OF AUDIO-VISUAL SYSTEM TYPES FOR EACH SPACE
AUDIO-VISUAL SYSTEM TYPE SCHEDULE ROOM NO.
ROOM NAME
B100
GYMNASIUM
B102
PA
200A
BLEACHERS
200B
BLEACHERS
2.8
A/V SYSTEM TYPE
QTY
NOTES
A
1
SYSTEM SPANS ALL ROOMS RACK IN #B102
SURGE PROTECTION A.
Surge Protection: Protect components from voltage surges originating external to equipment housing and entering through power, communication, signal, control, or sensing leads. Include surge protection for external wiring of each conductor-entry connection to components. 1.
2.
Minimum Protection for Power Connections 120 V and More: Auxiliary panel suppressors complying with requirements in Division 26 Section "Transient-Voltage Suppression for LowVoltage Electrical Power Circuits." Minimum Protection for Communication, Signal, Control, and Low-Voltage Power Connections: Comply with requirements in Division 26 Section "Transient-Voltage Suppression for LowVoltage Electrical Power Circuits" as recommended by manufacturer for type of line being protected.
Audio Visual Systems
27 4100 - 11
Vega High School Addition Vega Independent School District
PART 3 - EXECUTION
3.1
EXAMINATION A.
Examine pathway elements intended for cables. Check raceways, cable trays, and other elements for compliance with space allocations, installation tolerances, hazards to cable installation, and other conditions affecting installation.
B.
Examine roughing-in for LAN and control cable conduit systems to AV equipment, PCs, speakers, microphones and other cable-connected devices to verify actual locations of conduit and back boxes before device installation.
C.
Proceed with installation only after unsatisfactory conditions have been corrected.
3.2
PREPARATION A.
Comply with EIA/TIA-606, "Administration Standard for the Telecommunications Infrastructure of Commercial Buildings."
B.
In meetings with Architect and Owner, present Project planning documents and review, adjust, and prepare final setup documents. Use final documents to set up system software.
3.3
GENERAL INSTALLATION PRACTICES A.
All equipment with the exception of portable equipment shall be firmly fastened or attached in place. A safety factor of at least four shall be utilized for all brackets, fasteners and attachments.
B.
In the installation of equipment and cable, consideration shall be given not only to operational efficiency, but also to overall aesthetic factors.
C.
The Contractor shall insure that all equipment is installed such that proper cooling and ventilation is insured.
D.
All equipment shall be installed in a manner, which prevents hum, RF/EMI/EMF interference, and mechanical vibration based noises (e.g. fan mounts, etc.)
E.
All equipment shall be protected from construction dust and debris until final acceptance of the system.
F.
All equipment shall be protected from theft until final acceptance of the system.
G.
The Contractor shall be under obligation to protect completed work and uncompleted work against damage or loss until the Owner has given final acceptance. Should the need arise to repair work or replace items. The Contractor shall do so at no cost to the Owner.
Audio Visual Systems
27 4100 - 12
Vega High School Addition Vega Independent School District
3.4
FURNITURE A.
3.5
The Contractor shall ensure that equipment or mounting hardware is compatible with and suitable for installation in furniture specified by the Architect, Consultant, or Furniture Supplier. It shall further be the Contractor’s responsibility to ensure that such coordination with the Architect, Consultant, or Furniture Supplier occurs. The Contractor shall exchange with and follow such Shop Drawings as to ensure that dimensions and structural supports are adequate for the installation of specified equipment. It is the Contractor’s responsibility that the request and delivery of such critical coordination information is satisfactorily executed. Inasmuch as the Contractor has control over the delivery of such information, he shall deliver it as requested by the Architect, Consultant, or Furniture Supplier.
EQUIPMENT RACKS AND CABLE MANAGEMENT A.
Use tamper-resistant Torx type mounting screws for all rack-mounted A/V equipment.
B.
Racks shall be installed in such a way so as to permit access to all equipment for service.
C.
All equipment in racks shall be fitted with vent panels and/or fans as required to provide ventilation and cooling according to equipment manufacturer’s recommendations.
D.
Adjacent racks shall be bolted together with appropriate ganging hardware.
E.
As a general practice, all power cables, control cables, and high-level cables shall be dressed to the left rear of an equipment rack. Audio and video cables shall be dressed to the right rear of the rack. Audio, video and control cables shall be bundled separately and spaced not less than three (3) inches apart.
F.
Internal equipment rack cabling shall be supported by lacing strips, support brackets, or other cable management systems as required to ensure that all cabling is supported in both the vertical and horizontal planes within the rack.
G.
With the exception of ganged equipment rack assemblies, cabling routed between equipment racks or pieces of equipment exterior to equipment racks, or extending to the greater facility cabling infrastructure, shall be completely protected, end-to-end, by a raceway, wire-way, or duct appropriately sized for the cable run.
H.
Cabling between rolling pieces of equipment not housed in rack cabinets or a rolling equipment rack and any device to which it is connected, shall be protected by a split-loom corrugated tubing wrap or other such flexible cable management system appropriately sized for the cable run.
I.
Any controls not to be adjusted by the user and accessible from the front of the equipment rack must be furnished with security panels.
J.
UL Listing: Rack system shall be UL Listed in the US and Canada.
3.6
CABLING A.
3.7
Refer to Section 271622, Cabling for Audio-Visual Systems.
GROUNDING A.
Comply with Division 26 Section "Grounding and Bonding for Electrical Systems."
B.
Comply with IEEE 1100, "Power and Grounding Sensitive Electronic Equipment."
Audio Visual Systems
27 4100 - 13
Vega High School Addition Vega Independent School District
C.
Ground cable shields, drain conductors, and equipment to eliminate shock hazard and to minimize ground loops, common-mode returns, noise pickup, cross talk, and other impairments.
D.
Bond shields and drain conductors to ground at only one point in each circuit.
3.8
IDENTIFICATION A.
All equipment components shall be identified with a unique, permanently affixed laser-engraved label. Provide a schedule or database of labels and identifiers to Owner at completion of project installation.
B.
Cable Labeling: Comply with Section 271622, Cabling for Audio-Visual Systems.
C.
At completion, all labels and schedules shall reflect as-built conditions.
3.9
FIELD QUALITY CONTROL A.
Manufacturer's Field Service: Engage a factory-authorized service representative to inspect fieldassembled components and equipment installation, including connections. Report results in writing.
B.
Testing Agency: Owner will engage a qualified testing and inspecting agency to perform field tests and inspections and prepare test reports as required.
C.
System Set-up and Tuning 1.
D.
Optimization: The Contractor shall install, configure, adjust, program, and calibrate all components in order to optimize the performance of all individual subsystems and the system as a whole.
Preliminary Tests: 1.
2.
3.
General: Once the system is installed, the Contractor shall complete the following preliminary tests and prepare a written test report for the Consultant. The test report will list the results of each of the tests described in this section and certify that the installation is complete. Control: Upon completion of installation, the Contractor shall test each function of each control station, push-button panel, touch screen panel, computer control interface, and all components connected to or interfaced to the Control System to verify proper operation and that each switch and indicator operates as intended. Audio: The Contractor shall perform the following tests: a.
b. c. d. e. f.
Audio Visual Systems
Prior to the termination of audio amplifiers to speakers, the Contractor shall measure the resistance of the speaker line with reference to ground to determine that no short circuits or paths to ground exist in the line. The Contractor shall connect the speaker to the cable and measure the impedance of each speaker line using a 1,000Hz signal applied to the line. The Contractor shall submit a list, to the Consultant, by cable number, of the impedance of each speaker line. This test shall be performed with the amplifier disconnected from the speaker line and the speaker connected to the speaker line. Verify all loudspeakers are functioning. Verify that the system meets all Performance Requirements as outlined in this section. Verify that all equipment, panels, and cables are labeled correctly. Verify each item of equipment is functioning as intended. Verify the installation is the same as specified.
27 4100 - 14
Vega High School Addition Vega Independent School District
E.
Final Tests 1.
2.
3.
F.
3.10 A.
3.11 A.
3.12
Upon approval of the Contractor's test report, and at a time that is mutually acceptable to the Contractor, Owner and Consultant, the Contractor shall assist the Consultant and Owner in final system tests and adjustments. The Contractor shall allow one (1) day to perform the tests. The Contractor's representatives assisting in the performance of these tests shall be thoroughly familiar with the details of the system and shall include the field supervisor responsible for installing the system. To demonstrate the good working order of all playback devices in the system the Contractor shall make available high quality source materials for all audio and video media types represented in the system. The Contractor shall demonstrate operation of all subsystems, including audio and video recording, displays, cameras, camera controls, streaming, control system and so on, meets or exceeds the criteria as outlined in this section.
Remove and replace malfunctioning devices and circuits and retest as specified above.
STARTUP SERVICE Engage a factory-authorized service representative to supervise and assist with startup service as needed. Complete installation and startup checks according to approved procedures and with manufacturer's written instructions.
PROTECTION Maintain strict security during the installation of equipment and software. Rooms housing the AV components that have been powered up shall be locked and secured, with an activated access-control system or keyed system during periods when a qualified operator in the employ of Contractor is not present.
DEMONSTRATION
A.
Engage a factory-authorized service representative to train Owner's maintenance personnel to adjust, operate, and maintain AV system. Refer to Division 01 Section "Demonstration and Training."
B.
The Contractor shall provide a total of four (4) hours of on-site training for the Owner’s staff at a time that is mutually agreeable for the Owner and Contractor. The Contractor should anticipate two sessions of two hours each. The Owner may choose to have the sessions spread out over a maximum of two different days. Final acceptance and/or final payment for the system shall not be delayed due to scheduling delays beyond the control of the Contractor.
C.
In addition, the Contractor is responsible for scheduling and coordinating the specified manufacturer training with the Owner.
Audio Visual Systems
27 4100 - 15
Vega High School Addition Vega Independent School District
3.13 A.
SYSTEM ACCEPTANCE Upon successful completion of Final Tests, Documentation and Training, the Contractor shall notify the Owner, in writing, that the system is complete. The Owner shall have fifteen (15) days to generate a “punch list” of omissions, adjustments, corrections and the like and respond in writing to the Contractor. In the absence of such a “Punch List,” the system shall be considered to be complete. The warranty shall commence on the fifteenth day after the Contractor’s notification of completion of work, and the Owner shall process final payment. In the event that further work is required to complete this project, the Contractor shall be prepared to continue work, without additional compensation, until the system is accepted.
APPENDIX A: BASIS OF DESIGN SYSTEM CONFIGURATION [Attached to End of Document]
END OF SECTION
Audio Visual Systems
27 4100 - 16
Vega High School Addition Vega Independent School District
Vega High School Addition - Audio/Visual Systems APPENDIX A: Basis of Design System Configuration NOTE: THIS LIST CONSTITUTES THE EQUIPMENT USED IN THE "BASIS OF DESIGN" FOR THE AUDIOVISUAL SYSTEM. UNDER NO CIRCUMSTANCES SHALL THIS EQUIPMENT LIST BE TAKEN AS A COMPREHENSIVE LISTING OF ALL EQUIPMENT REQUIRED FOR A COMPLETE AND FUNCTIONAL SYSTEM AS SPECIFIED. CONTRACTOR IS RESPONSIBLE FOR PERFORMING THEIR OWN EQUIPMENT TAKE-OFFS AND VERIFYING ALL REQUIRED EQUIPMENT AND MATERIALS ARE PROVIDED. 1. Provide all necessary materials, turn-key installation, testing, and commissioning. 2. Provide all necessary software programming for automation control system, audio DSP, etc. 3. Provide end-user training as specified within these specifications. 4. The specific system configurations are listed in the following table. Each ‘system type’ includes a list of key components & instructions which is intended to serve as the basis-of-design / proof-of-concept; however these lists may not be comprehensive of all required materials, cabling, hardware etc. The contractor shall verify all specified components and instructions for compatibility with the intended functionality of the specified Audio-Visual systems – and provide additional materials etc. as required to perform the work – for turn-key installation of these systems.
Ref #
Item / Description
Make / Model
Unit Qty
A/V SYSTEM TYPE A: Gymnasium - [Begin] Loudspeakers: 1 2
Main Full-Range Loudspeaker Cabinet, 15" DualConcentric Driver, 75-degree Horizontal x 40-degree Vertical Dispersion, 58Hz - 30kHz Frequency Response, Black Color
Tannoy VX 15Q (8001 8310)
4
3
Yoke for Suspending Loudspeaker Cabinet
Tannoy VX 15 V YOKE (8001 7220)
4
4
12" Ceiling Loudspeaker, Coaxial 2-Way Type with 1" Compression Driver, Full Range, 33Hz - 21kHz Atlas 12CXT60 Frequency Response, 70V with 7.5, 15, 30, and 60 Watt Taps
5 6 7
Square Surface Mount Enclosure for Ceiling Loudspeaker, Paint to Match Ceiling Color Square Baffle for Loudspeaker Back Can, White Color, Paint to Match Ceiling Color Sound Reinforcement System:
2
Atlas Q4412
2
Atlas 164-12A
2
8
Audio Power Amplifier, 1200W @ 70V Split Between 2Labgruppen E12:2 ch with Support for Asymmetric Channel Loading, 1RU
2
9
Audio Power Amplifier, 400W @ 70V Split Between 2Labgruppen E4:2 ch with Support for Asymmetric Channel Loading, 1RU
1
10 11 12
Custom Wall Mounted Audio Input Connection Panel, (1) XLR Microphone Input and (1) Stereo RCA LinePanelCrafters Level Input, 1-Gang Passive Audio Summing Adapter with RCA Inputs and Extron ASA 141 (60-804-01) Transformer Balanced/Unbalanced Output Audio DSP, 10 Mic/Line Inputs, 6 Line Mic/Outputs, Biamp Nexia CS RS-232 and Ethernet Controllable, 1RU
Audio Visual Systems - Appendix A
2 3 1
27 4100 - 17
Vega High School Addition Vega Independent School District Ref #
Item / Description
A/V SYSTEM TYPE A: Gymnasium - [Begin]
13
14 15 16
Wireless Microphone Kit, includes (1) Rack Mount Receiver, (1) Handheld Stick Microphone, and (1) Body-Worn Transmitter with Cardioid Lavalier (ClipOn) Microphone
Shure SLX124/85/SM58-xx - includes the following: - (1) SLX4 Diversity Receiver - (1) SLX1 Bodypack Transmitter - (1) SLX2 Handheld Transmitter - (1) SM58 Dynamic Cardioid Mic Capsule - (1) WL185 Cardioid Lavalier Mic
Wireless Microphone Antenna Combiner, Antenna and Shure UA844SWB Power Outputs for (4) Receivers, 1RU Wireless Microphone Antenna In-Line Amplifier with Shure UA830 Mounting Bracket Wireless Microphone Antenna, 1/2 Wave Shure UA8 Omnidirectional Type
17
Input Cable for iPod/Media Player Connection to Wireless Microphone Beltpack Transmitter, Stereo 3.5mm Phone to Mono TA4F Mini-XLR with MonoSumming Network, 18"
18
Assistive Listening System (ALS):
Unit Qty
Make / Model
4
1 2 2
Roth Sound i-Kenny Kable
1
19
Intelligent Assistive Listening System (ALS) With Receivers for ADA Compliance in Rooms Up to 100 People, 72 MHz, Includes: (1) Stationary RF Transmitter (PPA T45) (1) Coaxial Antenna (ANT 005) (1) Rack Mounting Kit (RPK 005) (4) Portable RF Receivers (PPA R37) (4) Earbuds (EAR 013) (2) Neck Loops (NKL 001) (4) Pair Alkaline AA Batteries (BAT 001-2) (1) RCA to RCA Audio Cable (WCA 013) (1) Notification Wall Placard / Sign (IDP 008)
Williams Sound PPA 457 PRO
1
20
Portable RF Receiver Package, 72 MHz, Includes: (1) Portable RF Receiver (PPA R37) (1) Belt Clip (CLP 023) (1) Earbud (EAR 013) (1) Pair Alkaline AA Batteries (BAT 001-2)
Williams Sound PPA R37
24
Neck Loop, T-coil Capable, 18" Long Carrying/Storage Case for (22) RF Receivers and Accessories Control System: 7" Wall Mount Touchpanel, Uses Core 3 UI, Black Color Custom Rack Mount Panel For Touchpanel and Audio Connections, 3RU
Williams Sound NKL 001
5
Williams Sound CCS 036
1
Crestron TSW-750-B-S
1
PanelCrafters B87109-WQ442771
1
Crestron 3-Series Control Processor, DIN Rail Mount
Crestron DIN-AP3
1
Crestron PW-2407RU
1
Hammond Manufacturing RMAD19003BK
1
21 22 23 24 25 26 27 28 29
Power Supply for Control Processor, 18W Cresnet Power Rack Mount Adjustable DIN Rail for Control Processor, 2RU
PoE Ethernet Switch, 5 Ports -> 4 PoE + 1 Black Box LPB1205A Unpowered, 10/100/1000 Mbps, 61.4W PoE Capacity
Audio Visual Systems - Appendix A
1
27 4100 - 18
Vega High School Addition Vega Independent School District Ref #
Item / Description
A/V SYSTEM TYPE A:Power Gymnasium - [Begin] Uninterruptible Supply (UPS) for DSP and 30 Control Processor, 450VA, USB and RS-232 Control, 1RU 31 Bulk Cabling and Connectors:
Unit Qty
Make / Model
1
APC SC450RM1U / Smart-UPS SC 450VA
32
Shielded Twisted Pair Stereo Audio Cable, plenum, 2 pairs plus shield
Bulk Cable Type "AA02" - Refer to part 2.02 Bulk Cabling in Specification Section 271622 Cabling for Audio-Visual Systems
LOT
33
RS-232 Control Cable, Plenum
Bulk Cable Type "C01" - Refer to part 2.02 Bulk Cabling in Specification Section 271622 Cabling for Audio-Visual Systems
LOT
34 35 36 37 38 39 40 41 42 43 44 45
Bulk Cable Type "Lxx" - Refer to part 2.02 Bulk Speaker Cable, Plenum, Verify Required Cable Gauge Cabling in Specification Section 271622 Cabling for Based on Actual Conduit Runs Audio-Visual Systems Equipment Rack: Wall Mount Equipment Cabinet, 21RU x 20" Useable Depth, Multi-section Swing-out design, 200lb Weight Capacity Locking Vented Front Door for 21RU Rack, 64% Open Area Rear Rack Rails, 21RU Fan Kit, Includes: (2) 4.5" Fans, (2) Fan Guards, and Vent Blockers Thermal Fan Controller Rack Mount Power Distribution Unit, 1RU, Spike and Surge Protection, EMI Filter, No Front Power Switch Rack Mount Storage Drawer, 2 space Security Rack Screws with Torx (Star) Security Bit, Provide Bit to Owner Upon Project Closeout Blank Rack Panels - Solid Blank Rack Panels - Vented
LOT
Middle Atlantic DWR-21-22
1
Middle Atlantic LVFD-21
1
Middle Atlantic DWR-RR21
1
Middle Atlantic DWR-FK22
1
Middle Atlantic FC-4-1CA
1
Middle Atlantic PD-915R-PL
1
Middle Atlantic Products D2
1
Middle Atlantic HTX (with TBIT)
1
Middle Atlantic EBx Middle Atlantic VTx
LOT LOT
46 [End]
Audio Visual Systems - Appendix A
27 4100 - 19
2
31'-6"
8
27'-10"
12'-6"
10
11
3'-2"
11'-2"
12
14
1'-1"
GENERAL SHEET NOTES
15
12'-0"
2'-8"
SEE SB102C MATCHLINE
5 1'-0 1/2"
10
1
5'-0"
E4
1'-0 1/2"
SB301
E4
A5
SB301
D6 SB301 0 ] F5 '-5" 7 [9
TOP OF SLAB ELEV = [ 100'-0" ]
1
4 1'-4"
1'-0 1/2"
D1 SF201
D2 SB303
[97'-6"]
2
D4
22
1 SF20
C3
B4
SB302
SB302
" 4 3/4
SB301
SF401
SB302
SB302
F4 0
26
A4 SB301
13
B2
TOP (E) OF SLAB ELEV = [ 98'-8" ]
INDICATES GRADE BEAM TYPE. SEE SCHEDULE ON SB503 FOR SIZE AND REINFORCING INDICATES BOTTOM OF GRADE BEAM ELEVATION.
GB-1 [97'-0"]
SB303 SIM
9'-4"
2
SB301
1
9"
D3
A1
SB302
-2 ] PC '-0" 7 [9
H ARC SEE
1 7
RN
INDICATES BOTTOM OF FOOTING ELEVATION.
1'-4"
TOP OF SLAB ELEV = [ 100'-0" ]
26
1'-4"
" 19'-3
E2
3
SB301
15
INDICATES CONCRETE MICROPILE TYPE. SEE SCHEDULE ON SB503 FOR DESIGN SERVICE LOAD. INDICATES FOOTING TYPE. SEE SB503 FOR SIZE AND REINFORCEMENT.
P1
CF24
3
TOP (E) OF SLAB ELEV = [ 95'-2" ]
3
H ARC SEE
13
INDICATES FOOTING STEP. SEE B3/SB501.
2
D1
SB301
CF24
" 12'-5
C3
2 SF20
D NS E EN ON A L I CE
2/10/2016
INDICATES BOTTOM OF FOOTING ELEVATION.
3
7
SI
INDICATES FOOTING TYPE. SEE SB503 FOR SIZE AND REINFORCEMENT.
C A1
INDICATES FOOTING TYPE. SEE SCHEDULE ON SHEET SB503 FOR SIZE AND REINFORCING. INDICATES BOTTOM OF FOOTING ELEVATION.
3
2
SIM
TYP 4 LOCATIONS
SB302
HIGH
25
SB301
C3/SF503, COORDINATE LOCATION AND SIZE WITH ARCHITECTURAL
B2
1
D4 " 14'-1 H /ARC RD W COO
7'-0"
4'-8"
D4
SB301
A2
-3 ] PC '-8" 5 [9
A3
SB302
C2
L
PROJECT
INDICATES SLAB ISOLATION JOINT. SEE E6/SB501.
D
i
X
F-1092
E1
16
TOP OF SLAB ELEV = [ 98'-8" ]
D4
2
7
RP
5'-0"
1'-4"
5'-5"
RQ
SB301
A6
"] -0 8' [9
" 17'-3 H /ARC RD W COO
" 8'-11
" 10'-7
RR
C3
3
SB303
H ARC SEE
23. 24. 25. 26.
S
FOUNDATION LEGEND
26
H ARC SEE
19. 20. 21. 22.
O F TE
85682
D.2
2
12
21
C
SB301
2
3" 8'-4"
-0 PC
4'-4"
SB301
SB303
C2
H ARC SEE
5'-6"
SIM
B6
2
21
D3
18'-11"
A2
E
7'-11"
D1
SB303
RS
F
SB301
B2
7
8
9
-0 PC
7'-6"
7
RT
13
11
22
TYP
A3
SB302
16. 17. 18.
SB301
2'-0"
2'-0"
SB301
"] '-4 5 [9
3'-1"
22
A4
.
3.1
"] '-8 5 [9
PC -1
1'-4" [9 F50 6' -1 "] 1'-4 1/2"
3
13
PC -3
5'-3 1/2"
SEE ARCH
15.00°
SIM
7
14. 15.
[96'-2"]
2
RU
CF24A
1 SF20
1
13.
5
1'-0 1/2"
XRB
F6 [9 5' -1 0 0" ]
1
D3
E AT
n
CHARLES R. HANSON
E
1'-0 1/2"
SB301
6 1/2"
SB301
i ch/Sabat i
.
D1
D1
R2.9
G
SB301
OF
"] '-5 7 [9
SB301
8. 9. 10. 11. 12.
er /P
PR
0 F5
B5
D6
7
SB301
R3
2
TYP
ARCHITECT
L td
A1
G
SIM
1
7.
SIM
5" CONCRETE SLAB-ON-GRADE WITH #4 @ 18" OC EACH WAY, SEE A6/SB501. SLAB CONTROL JOINT, SEE C6/SB501. COLUMN ISOLATION JOINT/BLOCK-OUT, SEE E6/SB501. ELONGATED BLOCK-OUT TO FACILITATE BRACE FRAME. (2) #4 x 5'-0" AT RE-ENTRANT CORNERS. SEE DETAIL E5/SB501. SUMP PIT, COORDINATE SIZE AND LOCATION WITH ARCHITECTURAL DRAWINGS. SEE E6/SB301. 8" THICK CONCRETE SLAB WITH #5 @ 12" OC EACH WAY TOP AND BOTTOM. SEE B5/SB502. (NO CONTROL JOINTS) INFILL DEPRESSION WITH EPS-12 GEOFOAM, SEE B4/SB302. REPAIR EXISTING SLAB, SEE A2/SB501. PROVIDE PONY WALL SUPPORT PER DETAIL E1/SB501. CONTRACTOR TO VERIFY DIMENSIONS. SEE DETAIL C1/SB501 FOR RAMP DETAIL, COORDINATE WITH ARCHITECTURAL FOR DIMENSIONS. LOCATE EXISTING FOUNDATION, IF EXISTING FOUNDATION INTERFERES WITH MICROPILE CAP INSTALLATION, CONTACT ENGINEER. VERTICAL BARS AND DOWELS AT THESE LOCATIONS SHALL BE #8 @ 6" OC. SLOPE SLAB TO DRAIN MAX 1/8" PER FOOT. MAINTAIN THICKNESS OF SLAB. COORDINATE EXTENTS AND LOCATIONS WITH ARCHITECTURAL. COORDINATE RAMP DIMENSIONS WITH ARCHITECTURAL. 1 NOT USED. TRENCH DRAIN. COORDINATE LOCATION WITH ARCHITECTURAL AND PLUMBING. STEP ADJACENT FOUNDATION ADDITIONAL 8" DOWN. MOP SINK. COORDINATE WITH ARCHITECTURAL AND PLUMBING. MAX RETAINAGE = 2'-0". 4'-0"x4'-0" SLOPE TO DRAIN. MAX SLOPE TO DRAIN = 1/8"/FT. MAX DEPRESSION = 1/2" MECHANICA DUCT OPENING IN SLAB, COORDINATE SIZE AND LOCATION WITH MECHANICAL. SEE A5/SB502 FOR SLAB REINFORCING. 12" THICKENED SLAB, #4 @ 12" OC EACH WAY 3" FROM THE BOTTOM OF THE SLAB. 3 SEE C5/SB301 FOR ROOF DRAIN DETAIL THROUGH SLAB/STEM WALL. BRACE ARCHITECTURAL WALL AT FLOOR LINE PER DETAIL C6/SB301. REPAIR AND REPOINT CRACKED JOINTS IN EXISTING MASONRY WALLS WITHIN THE AUDITORIUM, TYPICAL ALL INTERIOR WALLS.
S A
5
3
1. 2. 3. 4. 5. 6.
SIM
[96'-2"]
[9 F50 6' -1 "]
5
2
,
-2 ] PC '-0" 7 [9
-6 PC "] -0 7' [9
SEE SB102A
RV
CF24A
TOP OF SLAB ELEV = [ 98'-8" ]
MATCHLINE
26'-10"
1
CF24A
8'-5"
24'-3"
2
42'-10"
TYP
SB301
D
SHEET KEYED NOTES
SEE ARCH
E4
R
0 F5 "] -5 7' [9
SB301
H
EE
B5
G.9
SB301
SB303
G IN
24
C2
B5
1'-0 1/2"
2'-7"
H
15
[9 F60 7' -2 "]
3
[9 F50 7' -5 "]
[97'-6"]
[97'-6"]
CF24A
CF24A
SIM
SB301
200 Longhorn Street Vega, TX 79092
2
F6 [9 5' -1 0 0" ]
SF201
[96'-2"]
C5
CF24A
"] -2 ' 7 [9
[9 F50 6' -1 "]
21'-5"
E
0 ] F4 '-5" 7 [9
0 ] F5 '-5" 7 [9
0 F7
[96'-2"]
"] -2 ' 7 [9
[97'-6"]
4
0 F6
26
INDICATES FOOTING STEP. SEE B3/SB501.
[97'-0"]
1'-0 1/2"
J
3
VEGA ISD HIGH SCHOOL
4
A. REFERENCE FINISHED FLOOR ELEVATION AT THE FOUNDATION LEVEL = 100'0" UNO, SEE CIVIL FOR MSLE. B. SEE ARCHITECTURAL DRAWINGS FOR DIMENSIONS NOT SHOWN. C. SEE SHEETS SB301 THRU SB601 FOR FOUNDATION SECTIONS, DETAILS AND SCHEDULES. D. DIMENSIONS ARE TO FACE OF CONCRETE STEMWALL OR FACE OF MASONRY OR CONCRETE UNLESS SHOWN HEREIN. E. FOR LAP SPLICE AND EMBEDMENT SCHEDULE, STANDARD HOOK, END HOOK TYPES, STIRRUP AND TIE HOOKS, SEE SB503. F. SEE ARCHITECTURAL FOR EXACT DIMENSIONS AND LOCATIONS OF STEPS AND DEPRESSIONS IN INTERIOR SLAB. G. AVOID INSTALLING PIPES, CONDUIT, ETC BENEATH COLUMN FOOTINGS. WHERE PIPES AND CONDUIT MUST PASS UNDER CONTINUOUS FOUNDATION OR THROUGH STEMWALLS SEE DETAILS E2, D2, AND C2 ON SB501. WHERE PIPES OR CONDUIT MUST PASS THROUGH GRADE BEAMS, SEE DETAIL A1/SB501. H. CONTRACTOR SHALL COORDINATE INSTALLATION OF ELEVATOR GUIDE RAILS SUPPORT POSTS WITH ELEVATOR SUPPLIERS DRAWINGS. I. CONTRACTOR SHALL COORDINATE ELEVATOR PIT DIMENSIONS AND LOCATION SHOWN ON PLAN AND SECTION WITH ELEVATOR SUPPLIERS DRAWINGS. J. CONTRACTOR SHALL COORDINATE OPENINGS AND TOP OF STEM WALL WITH ARCHITECTURAL AND CIVIL. ANY DISCREPANCIES SHALL BE REPORTED TO ARCHITECT FOR RESOLUTION. K. ALL BASEMENT RETAINING WALLS SHALL BE SHORED BY CONTRACTOR BEFORE BACKFILLING. SEE S001 FOR ADDITIONAL INFORMATION. 1 L. NOT ALL KEYED NOTES MAY APPLY TO THIS SHEET. M. SEE C5/SB301 FOR ROOF DRAIN INSET INTO SLAB. COORDINATE WITH PLUMBING AND ARCHITECTURAL FOR LOCATIONS.
ST
11'-2"
7
Dek ke r
40'-2"
5
[97'-0"]
6'-0"
4
6
[98'-0"]
3
5
[98'-0"]
1'-0 1/2"
1
4
[98'-0"]
0.5
3
[98'-0"]
1
INDICATES MASONRY WALL.
TYP
B
WP
1 1
A4
0" 21'-1
7
SB302
5
SB301
A2
SB302
SB302
A2
1 TOP (E) OF SLAB ELEV = [98'-8"]
3
5
E4 B5
5 GB-1
8"
5'-4"
RG
7
E4
/2" 3'-0 1
SB302
B2
A2
SF201
SB303
15.00°
22'-6"
SB302 B5
SB301
SB303
-2 ] PC '-4" 5 [9
"]
ADDENDUM 001
2
2/9/16
ADDENDUM 003
3
2/11/16
ADDENDUM 004
20'-10"
3'-5" 2'-8"
KEYPLAN
14'-5"
SB301
6.5
8
9
10
13
14
15
16 DRAWN BY
SB302
AREA C
8.8
EXISTING
" 15'-5
-0 PC
" 15'-2
E4
A1
-0 PC
3'-1"
"] [96'-8 1 B G
4'-8"
SB302
INE CHL MAT 2A SB10 SEE
4'-4"
RB
2'-4"
3'-6"
R7 " 25'-5
R5
R8
CH, BB 01.22.2016
PROJECT NO: MATCH LINE
" 12'-8
REVIEWED BY DATE
R9
RW
14-0424.002
DRAWING NAME
R8.1
FOUNDATION PLAN - AREA B AREA B
R6 AREA A
" 10'-4
RA
R3
NORTH
1/8" = 1'-0"
2
3
4
5
INE CH L MAT
R2.9
A1 FOUNDATION PLAN - AREA B 1
2/4/16
SF202
8" 1'-0"
1'-6"
D5
E1
1
B2
SB303
" 10'-0
SB302
9'-8"
2/10/2016 11:34:45 AM
SB301
-0 PC
E4 D6
REVISIONS
24
10
RD
A
"] [96'-8 GB-1
GB-1 [95'-4"] 24
E4
4'-4"
RE
GB-3 [96'-8"] 1
A1
-0 PC
"]
[96'-8
/2" 1'-0 1
GB-1
" 11'-6
2
-0 PC
/2" 1'-0 1
SB303
-4 PC "] -8 6' [9
10
[96'-8
1'-0"
RF 1
GB-1 [96'-8"]
1
SB303
13
B
A
R
SB303
3'-2"
RJ
C3/SF503, COORDINATE LOCATION AND SIZE WITH ARCHITECTURAL
INDICATES MASONRY PILASTER. SEE A1/SF503. INDICATES MASONRY WALL REINFORCEMENT. SEE A6/SF503. INDICATES MASONRY CONTROL JOINT (MCJ). SEE D6/SF503. INDICATES SLAB DEPRESSION. SEE D4/SB501 AND E4/SB501 FOR SLAB-ON-GRADE. AT ELEVATED SLAB, SEE C6/SB502.
1 1/2"
7
5
1'-0 1/2"
E4
MP-1
SB302
2
4
8S532P
5
SF503 12
5
-7 ] PC '-4" 5 [9
-5 ] PC '-5" 6 [9
D1
D3
A2
.
SB303
5'-1"
SB302
MCJ
A4
B2 7
22'-10"
SB301
RK
SHEET NO.
SB102B 6
2
3
W14x22
/4 x1 5 x S5 HS
W14x22
F
6"
6"
A1 SF301
3'-1"
R
EE
G IN
INDICATES THRU PLATE CONNECTION, SEE A5/SF502.
1
HSS6x4x5/16 [ 108'-8" ]
B
W18x40 [ 108'-8" ]
A 0 D .25 x0 2 U S5 1/ HS x6x 2 S1 HS
U
T
U
U
U
H SS 6x 6x 1/ 4
REVISIONS 1
2/4/16
ADDENDUM 001
2
2/9/16
ADDENDUM 003
3
2/11/16
ADDENDUM 004
1
D5 SF202
22'-6"
B3
2'-2"
1'-0"
20'-10"
3'-5" 2'-8"
KEYPLAN
14'-5"
SF301
6.5
B6
9
10
13
14
15
16
6"
DRAWN BY " 15'-5
B
SF502
AREA C
8.8
2'-4"
EXISTING
MATCH LINE
R7
R8
RW CH, BB 01.22.2016
PROJECT NO:
R9
3'-6"
REVIEWED BY DATE
" 12'-8
INE CHL MAT 3A SF10 SEE
4'-4"
R5
8
14-0424.002
DRAWING NAME
R8.1
ROOF FRAMING PLAN - AREA B
R6
AREA B AREA A
NORTH
1/8" = 1'-0"
3
4
5
INE CH L MAT
R3
2
ST
7'-11" 42'-10"
A
9
1/2 6x x 2 S1 HS
INDICATES COLUMN SIZE.
SF301
1/4 4x T x S6 OS P HS
T
1
1/4 4x x S6 HS
U
SF201
D
HSS6x4x5/16 LLH [ 108'-8" ]
INDICATES BASE PLATE TYPE, SEE A3/SB503.
D3
1
A1 ROOF FRAMING PLAN - AREA B 1
Dek ke r
19
8'-5"
3'-4" MIN
2
1/2 6x 2x S1 /8 HS 6x3 x S8 HS x1/2 6 2x S1 HS
J
D6
200 Longhorn Street Vega, TX 79092
(4) EQ SPACES
INDICATES BRACE FRAME, SEE SF201 FOR ELEVATIONS.
1/2 6x 2x S1 /8 HS 6x3 x S8 HS x1/2 6 2x S1 HS
" 15'-2
2/10/2016 11:35:25 AM
/4 x1 x4 S6 HS
/16 0 x5 0.25 4 x x S4 S5 HS HS
SF301
6"
1/4 5x x S5 HS
B3
RA
INDICATES TOP OF STEEL ELEVATION.
1
" 25'-5
RB
[110'-0"]
14
SF301
W18x35
J
SF301
4'-8"
SF301
SF301
INDICATES ADDITIONAL CAMBER.
D
x14 W12 1/2" ] '-10 [ 112
RD
(B) W14x22 (30)
INDICATES ADDITIONAL CAMBER. INDICATES TOP OF STEEL ELEVATION.
[110'-0"] B5
INDICATES BRACE FRAME, SEE SF201 FOR ELEVATIONS.
SF301 22K4
22K4
6 5/1 x x5 S5 S H
B
INDICATES COLUMN SIZE. A
W14x22
W16x26
INDICATES BASE PLATE TYPE, SEE A3/SB503.
22K4
H
1
H SS 6x 6x 1/ 4
INDICATES THRU PLATE CONNECTION, SEE A5/SF502.
M
/16 x5 4 4x SS
W12x19
20K4
20K4
5 REVISIONS A6
5
20K4
20K4
20K4
1
2/4/16
ADDENDUM 001
3
2/11/16
ADDENDUM 004
SF201
W12x19
12K1
12K1
SI
INDICATES BEAM SIZE.
B
/4 x1 5 x S5 HS
L
KEYPLAN
J
MATCHLINE
12K1
13
26K6
26K6
12K1
B
/16 x5 x4 S4 HS
1'-0"
26K6
13
W16x26
7'-3"
26K6
12K1
INDICATES BLOCKING BETWEEN JOISTS FOR LENGTH OF BEAM, SEE DETAIL D1/SF502.
(B) W16x26
1,125 LBS 12K1
/4 x1 x5 S5 HS
L
A4
1
12K1
B
M
1
N
(2) EQ SPACES (2) EQ SPACES
26K6
(4) EQ SPACES
2'-1" 6'-2"
/4 x1 x5 S5 HS
B
26K6
12K1
12K1
26K6
P
INDICATES MASONRY WALL.
ML-1
INDICATES MASONRY LINTEL. SEE A2/SF503 FOR REINFORCING. SEE ARCH FOR SIZE AND LOCATION.
(B) W14x22
SF301
Q
13
/4 x1 5 x S5 HS
W21x50
1
12K1 1,150 LBS
(2) EQ SPACES
W21x50 10'-8"
26K6 B5
INDICATES WALL OPENING, SEE A2/SF503 FOR REINFORCEMENT. SEE ARCH FOR EXTENT OF OPENING.
W14x22
(2) EQ SPACES
9'-4"
26K6
12K1
/16 x5 x5 S5 HS
1
13
B
26K6
B
SF502
SF301
SF502
1,125 LBS W12x14
(2) EQ SPACES (2) EQ SPACES
W24x55
(2) EQ SPACES
1
26K6
(2) EQ SPACES
26K6
(2) EQ SPACES
W12x14 W12x14
8'-7"
S
20K4
B4
INDICATES STEEL STUD WALL.
C2
C6
SF502
T
INDICATES WALL OPENING, SEE B3/SF501 AND A4/SF501 FOR SCHEDULE AND FRAMING. SEE ARCH FOR EXTENT OF OPENING.
1
20K4
E4 W16x31
R
12K1
SF301
i
X
PROJECT
INDICATES STEEL DECK TYPE. SEE TYPICAL STEEL DECK DETAILS ON SHEET A6/SF501.
1-
C4
N
(2) EQ SPACES
SF301
13
(4) EQ SPACES
/4 x1 x5 S5 HS
B
C5
1
1
19'-3"
20K4
885 LBS 12K1
1
O F TE
n
F-1092
FRAMING LEGEND
/16 x5 5 5x SS
20K4
W24x55
1
(B) W14x22
SF301
SF201
H
1
W16x31
12K1 (4) EQ SPACES
5
(4) EQ SPACES
20K4 B5
1
W16x31
C1
A4 SF502
4
4
(4) EQ SPACES
(B) W16x26
9'-3"
U
12K1
1
W21x44
W14x22
12K1
7
C2 SF301
W16x31
L
1
13
/16 x5 x5 S5 HS
22K4
B
/16 x5 4 x S4 HS
W14x22
J
885 LBS W12x14
24K5
5 .37 x0 S6 HS
C
D
S
A
SF201
12K1
W12x19
E AT
85682
/4 x1 x4 S4 HS
V
x S6 S H
SF502
D
C3
M
1/8" = 1'-0"
24K5
50 0.2
i ch/Sabat i
CHARLES R. HANSON
D5
0 .25 x0 S6 HS
10'-0" 1'-1"
W12x19
er /P
2" EXPANSION JOINT
D1
ML-3 W12x14
W18x40 (30)
SF202
SF303
ARCHITECT
20
(2) EQ SPACES
SF302
H
1/4 8x x S8 HS
3
16. 17. 18. 19. 20.
BRIDGING: PER SJI MANUAL/UPLIFT REQUIREMENTS, EQUALLY SPACED. WELD TO TOP AND BOTTOM CHORD OF JOIST. L3x3x1/4 DIAGONAL BRIDGING SEE C2/SF501 FOR SIMILIAR ATTACHMENT. 2 COORDINATE. SEE E5/SF501 FOR RTU SUPPORT. BOTTOM FLANGE BRACE AT ROOF PERPENDICULAR TO FRAMING, EQUALLY SPACED UNLESS NOTED OTHERWISE. SEE C2/SF501. BOTTOM FLANGE BRACE AT ROOF PARALLEL TO FRAMING, EQUALLY SPACED UNLESS NOTED OTHERWISE. SEE B2/SF501. EXISTING MASONRY WALL BELOW. ROOF HATCH, COORDINATE EXACT LOCATION WITH ARCHITECTURAL. SEE A5/SF501 FOR FRAMING. SEE E1/SF103A FOR LOADING DIAGRAM FOR THESE JOISTS ONLY. HSS4x4x1/4 STRUTS @ 16" OC. FAN SUPPORT MAX WEIGHT = 500 LBS, COORDINATE BEAM LOCATION WITH ARCHITECTURAL. BASKET BALL SUPPORT, COORDINATE BEAM LOCATION WITH ARCHITECTURAL / MANUFACTURER. SEE D2/SF301 FOR BRACING AT BASKETBALL ATTACHMENTS SEE D1/SF301 FOR DUCTS ENTERING INTO TORNADO SHELTER. COORDINATE SIZE AND LOCATION WITH MECHANICAL. FOR MECHANICAL DUCT OPENINGS, FRAME PER A5/SF501. COORDINATE SIZE AND LOCATION WITH MECHANICAL. NEW OPENINGS IN EXISTING MASONRY WALL, SEE DETAIL C3/SF503. EDGE OF NEW OPENING SHALL BE LOCATED A MINIMUM OF 2' AWAY FROM EXISTING BEAM BEARING. PROVIDE ANGLE STRONG BACKS ON THE INTERIOR SIDE OF THE WALL ON EACH SIDE OF THE OPENING. FOUR SIDED SCORE BOARD, MAX. WEIGHT = 1500 LBS. CONTRACTOR TO COORDINATE BEAM LOCATION WITH MFG. PROVIDE DUCT SUPPORTS PER E3/SF301. COORDINATE WITH MECHANICAL. EXISTING OPENING IN ROOF. INFILL OPENING WITH DECK TYPE 1 PER DETAIL A2/SF501. 600S162-68 AT 8" OC. SEE B5/SF301 FOR SIMILAR WALL CONSTRUCTION. 3 BOTTOM OF DECK = 111'-2". SEE DETAIL E3/SF503 FOR OPENING DETAIL BETWEEN SHUTTER AND MECHANICAL AIR INTAKE.
ML-3
ML-3
W12x19 (10)
(4) EQ SPACES
1,125 LBS
W18x40 (30)
(3) EQ SPACES
1'-9"
D1 2" EXPANSION JOINT
/16 x5 x4 S4 HS
A2 ROOF FRAMING PLAN BID LOT #4
W18x40 (30)
W12x19 (10)
12
/4 x1 x8 S8 HS
W
SF502
H
W.2
D5
(4) EQ SPACES
3
W.1
12
W18x40 (30)
(2) EQ SPACES
20
W18x40 (30)
15.
(4) EQ SPACES
W18x40 (30)
W16x26
W12x19 (10)
W18x40 (30)
SF302
(2) EQ SPACES
W18x40 (30)
14.
W12x19 (10) W21x44 (22)
E5 SF303
13.
E1
(2) EQ SPACES
SF303
12.
SF302
(4) EQ SPACES
W18x40 (30)
W18x40 (30)
11.
E1
ML-3
W12x19 (10)
SF302
12
12
W18x40 (30)
ML-3
ML-1 W18x40 (30)
8. 9. 10.
1,125 LBS
12
Y.9
G
/16 x5 8 x S8 HS
W12x19 (10)
W12x19 (10)
E5
W21x44 (22)
(4) EQ SPACES
2
SF302
W12x19 (10)
W21x44 (22)
W18x40 (30)
6. 7.
W18x40 (30)
W16x26
6 H 5/1 x x8 D1 S8 S H SF202
G
5.
12 W12x19 (10)
1. 2. 3. 4.
E2
6 5/1 8x W18x40 (22)
16'-4"
SF303
x S8 S H
W18x40 (30)
20
W18x40 (30)
W12x19 (10) 1,125 LBS
W18x40 (22)
ML-3
SF302
3
ML-3
11'-5" (5) EQ SPACES
(5) EQ SPACES
ML-3
W18x40 (30)
E1
20'-7"
Z
1'-9"
W12x19 (10)
W24x76 (34)
ML-3
W24x76 (34)
1,125 LBS W12x19 (10)
C5
(5) EQ SPACES
12'-8"
9"
1'-9" 27'-6" 9"
W12x19 (10)
W18x40 (30)
W18x40 (30)
Y
H
G
/16 x5 8 8x SS
3
.
W12x19 (10) 1,125 LBS
3 20
12
/16 x5 x8 S8 HS
SF302
W18x40 (30)
12
C5 SF303
W18x40 (30) 12
W12x19 (10)
G
Z.1
/16 x5 x8 S8 HS
E1
H
W18x40 (30)
ML-3
SF502
SHEET KEYED NOTES
E
W18x40 (30)
2
SF502
W12x19 (10)
W18x40 (30)
20
D5
1,125 LBS
2
D5
OF
SF302
2
W18x40 (30)
20
SF502
20
L td
W18x40 (30)
SF303
3
W18x40 (30)
D5
W18x40 (30)
,
SF502
3
12
3
3
PR
D
E2
SF303 D5
20
3
B6
SF303
W18x40 (30)
20
SF302
SF303
S A
3
20
H
B6
B6
(3) EQ SPACES
ML-3
B6 W18x40 (30)
3
/16 x5 8 x S8 HS
SF202
Z.9 Z.8
D1
3
ML-3
SF303
/16 x5 x8 S8 HS
H
SF302
Y.9
D2
ML-3
A6
19'-7"
D2
1'-9"
Z
R
SF202
SF302
H
1/4 8x x S8 HS
EE
SF303
D1
ML-3
SF302
11"
D2
(4) EQ SPACES
31'-6"
/4 x1 x8 S8 HS
11'-2"
H
31'-6"
11"
A6
D2 11"
31'-6"
G IN
31'-6"
(4) EQ SPACES
11"
(3) EQ SPACES
7'-9"
3
6'-0"
5.1
5
(3) EQ SPACES
4
(4) EQ SPACES
3
(2) EQ SPACES
2
(2) EQ SPACES
1.9
200 Longhorn Street Vega, TX 79092
2
VEGA ISD HIGH SCHOOL
1.9
ST
1
E
Dek ke r
0.5
A. PROVIDE JOIST BRIDGING IN ACCORDANCE WITH LATEST EDITION OF SJI STANDARD SPECIFICATIONS. B. REFER TO ARCHITECTURAL DRAWINGS FOR SIZE AND LOCATION OF STUD WALL OPENINGS. SEE B3/SF501 FOR LINTEL FRAMING AND SCHEDULE. C. "K" SERIES ROOF JOIST SEATS SHALL BE 2 1/2" DEEP AND "LH" SERIES ROOF JOISTS SHALL BE 5" DEEP, UNLESS NOTED OTHERWISE. TOP OF STEEL BEAMS WHICH ARE PARALLEL TO JOISTS SHALL BE 2 1/2" HIGHER THAN TOP OF GIRDER AT EACH END, UNLESS NOTED OTHERWISE. D. WHERE JOISTS SUPPORT CONCENTRATED LOADS, SEE C5/SF501. E. SLAB EDGE AT ELEVATOR PIT SHALL BE VERIFIED WITH ELEVATOR SUPPLIERS DRAWINGS. F. SEE A5/SF501 FOR MISCELLANEOUS OPENINGS IN ROOF DECK. G. GENERAL CONTRACTOR IS TO COORDINATE DIMENSIONS OF ROOF TOP MECHANICAL UNITS DUCT OPENINGS. H. MECHANICAL UNITS 300# AND HEAVIER ARE SHOWN ON PLAN. MAXIMUM WEIGHT IS SHOWN. I. SEE D1/SF503 FOR LOOSE LINTEL VENEER SUPPORT AT ARCHITECTURAL OPENINGS LESS THAN 8'-0" OC, UNO. COORDINATE LOCATIONS/SIZE WITH ARCH. FOR OPENINGS EXCEEDING 8'-0", SEE PLAN FOR SUPPORT, UNO. J. NOT ALL KEYED NOTES MAY APPLY TO THIS SHEET. K. NOT ALL OPENINGS ARE LOCATED ON PLAN, COORDINATE WITH ARCHITECTURAL, MECHANICAL, PIPING, AND ELECTRICAL. SEE DETAIL A5/SF501. L. FOR DUCTS AND PIPES ENTERING SIDEWALL OF THE SHELTER SEE DETAIL C2/SF302 AND C6/SF503. M. BOTTOM OF DECK ELEVATION = 113'-8" UNO.
DRAWN BY REVIEWED BY
AREA C
SEE SF103B
DATE
5
MATCH LINE
A
CH, BB 01.22.2016
PROJECT NO:
J
RW
14-0424.002
DRAWING NAME
ROOF FRAMING PLAN - AREA C AREA B
NORTH
A1 ROOF FRAMING PLAN - AREA C 1/8" = 1'-0"
1
2
3
4
5
INE CH L MAT
2/10/2016 11:35:32 AM
AREA A
SHEET NO.
SF103C 6
(2) 8" DEEP BOND BEAMS W/ CONT REINF IN EACH, TOP BOND BEAM REINF IS DISCONTINUOUS AT BEAM BEARING, TYP MASONRY WALL REINFORCEMENT, SEE PLAN
STEEL BEAM BEYOND, SEE PLAN PL 3/4"x12"x10" WITH (2) 3/4"x6" HAS SPACED 8" APART CENTERED ON PLATE
CMU WALL, SEE PLAN
1/8
ROOF DECK, SEE PLAN
DECK, SEE PLAN
SEE C4/SF302 FOR VENEER SUPPORT
1/8
JOIST BEARING SEE PLAN L5x3x1/4 LLH
SEE
SLAB DOWELS
PLAN
DECK, SEE PLAN
ATTACH METAL DECK WITH SHOT PINS AT 16" OC, TYP
VENEER, SEE ARCH ADDITIONAL CHORD REINFORCEMENT, (4) # 6 CONTINUOUS
SIZE AND SPACING OF SLAB DOWELS TO MATCH SLAB REINFORCEMENT
3/4" = 1'-0"
T O WALL SEE PLAN SEE C4/SF302 FOR VENEER SUPPORT
POST, SEE PLAN
SHELTER ROOF FRAMING SECTION
D2
3/4" = 1'-0" T O WALL SEE PLAN
L3x3x1/4 BRIDGING WELD EACH SIDE WITH 3/16 WELD ON EACH SIDE OF ANGLE
ROOF DECK, SEE PLAN
L5x5x1/4x1'-0" LONG ATTACHED WITH (2) 3/4"Ø DIAMETER SCREW ANCHORS
NOT USED
CMU WALL, SEE PLAN
D3 D3/SF302 - SECTION
D4 SECTION
3/4" = 1'-0"
T O STEEL SEE PLAN 5/16" PLATE DUCT ASSEMBLY CONT, WELD ALL JOINTS 1/8" MIN
L5x3x1/4 LLH ROOF DECK, SEE PLAN
ADDITIONAL BRIDGING AT DUCT ASSEMBLY CENTERLINE
BUILD MASONRY TIGHT TO DUCT ASSEMBLY, TYP, ALL SIDES
8"
RETURN ON DUCT ASSEMBLY MAY TURN DOWN OR EITHER SIDE, SEE MECH
L4x4x1/4 FRAME W/ (2) 1/2"Ø SCREW ANCHORS ON EACH SIDE
A2 SIM
C1 SECTION
C2
3/4" = 1'-0"
OPENING SEE MECH
STRUCTURAL SIDEWALL DUCT ASSEMBLY DETAIL
i ch/Sabat i
E AT
O F TE
n
i
X
CHARLES R. HANSON
85682 S
L SI
JOIST, SEE PLAN PL3/8"x6"x0'-9" WITH (2) 1/2"Øx4" HAS
D NS E EN ON A L I CE
2/10/2016
F-1092
PROJECT
SF302
D6
3/4" = 1'-0"
1'-0"
1'-0"
1'-0"
SEE PLAN FOR WALL REINFORCING
SEE PLAN
ROOF DECK, SEE PLAN
SF301
er /P
JOIST BEARING AT CMU WALL 3/4" = 1'-0"
3/4" = 1'-0"
L5x3x1/4 LLH
T O BRNG SEE PLAN
ARCHITECT
DECK, SEE PLAN
8" OR 12" CMU WALL, SEE PLAN FOR REINF
1
SF301
JOIST, SEE PLAN
1/8
VENEER COORDINATE WITH ARCH FOR LOCATION
C5
4"
C
EACH JOINT
JOIST, SEE PLAN
NOTE: IF CONCRETE BEAM IS ENCOUNTERED ABOVE WALL, CONTACT ENGINEER OR ARCHITECT IMMEDIATELY FOR RESOLUTION
SHELTER ROOF FRAMING SECTION
1
4"x12" POCKET IN CMU WALL
T O SAWCUT WALL 98'-0"
A2
SEE C4/SF302 FOR VENEER SUPPORT
1/8 (1) #5 CONTINUOUS IN 8" CMU BOND BEAM ((2) #5 CONTINUOUS IN 12" CMU) JOIST BEARING SEE PLAN
PL1/2"x5x10 W/ (2) 1/2" Ø THREADED RODS EXPOSED 4" INTO CONC
3/16
MASONRY WALL REINFORCEMENT, SEE PLAN
T O WALL SEE ARCH
CHANNEL W/ (2) 1/2"Ø THRU BOLTS
3" 6" 3"
6" 3"
MASONRY WALL REINFORCEMENT, SEE PLAN
SF301
CMU WALL, SEE PLAN
CONT PL3/8x10
CONTINUOUS L5x3x1/4 LLH WITH 1/2"Øx3 /12" SCREW ANCHOR @ 24" OC INTO BOND BEAM
A2
.
L5x5x1/4x1'-0" LONG ATTACHED WITH (2) 3/4"Ø DIAMETER SCREW ANCHORS
3/4" = 1'-0"
ROOF DECK, SEE PLAN
2 1/2"
(2) 8" DEEP BOND BEAMS W/ CONT REINF IN EACH, TOP BOND BEAM REINF IS DISCONTINUOUS AT BEAM BEARING, TYP
3/4" = 1'-0"
E
L3x3x1/4 BRIDGING WELD EACH SIDE WITH 3/16 WELD ON EACH SIDE OF ANGLE
(2) 8" DEEP BOND BEAMS W/ CONT REINF IN EACH, TOP BOND BEAM REINF IS DISCONTINUOUS AT BEAM BEARING, TYP
E6 SECTION
L td
2 1/2" TYP
E5 SECTION
,
3"
E4 SECTION
3/16
NOTE: NO BRIDGING AT SIM
OF
SF301
T O STEEL SEE PLAN
PL 3/4"x6"x1'-4" W/3-1/2"Øx4" HAS
L3x3x1/4xJOIST DEPTH WITH (2) 1/2'Ø x 3 1/4" EXPANSION ANCHORS INTO GROUTED CELLS
PR
B6
DECK, SEE PLAN
JOIST, SEE PLAN
BEAM OR JOIST, SEE PLAN BRIDGING, PER JOIST MANUFACTURER
SF302
SIM
E3
8" DEEP BOND BEAM WITH (1) #5 CONT
T O STEEL SEE PLAN
VENEER COORDINATE WITH ARCH FOR LOCATION
D6
8" MASONRY WALL WITH #5 @ 24" OC VERTICAL, EMBED REINFORCEMENT 4" INTO CONCRETE WITH ADHESIVE PER S001
TO PARAPET SEE ARCH
8" OR 12" CMU WALL, SEE PLAN FOR REINFORCING
SIM
E6
DECK, SEE PLAN
S A
2"
ADDITIONAL CHORD REINFORCEMENT, (4) # 6 CONTINUOUS
SEE PLAN
ATTACH METAL DECK WITH SHOT PINS AT 16" OC, TYP.
3/4" = 1'-0"
2"
2" EXP JOINT
8" DEEP BOND BEAM WITH (1) #5 CONT
JOIST, SEE PLAN
ATTACH METAL DECK WITH SHOT PINS AT 16" OC, TYP.
SHELTER ROOF FRAMING SECTION
E2
8" MASONRY WALL WITH #5 @ 24" OC VERTICAL, EMBED REINFORCEMENT 4" INTO CONCRETE WITH ADHESIVE PER S001
STEEL BEAM BEYOND, SEE PLAN
TYP
1/8
VENEER, COORDINATE WITH ARCH FOR LOCATIONS
(2) #5 CONTINUOUS IN BOND BEAM, TYP JOIST BEARING SEE PLAN
(1) #5 CONTINUOUS IN 8" CMU BOND BEAM ((2) #5 CONTINUOUS IN 12" CMU) T O JOIST VARIES
JOIST BEARING EL SEE PLAN
SEE C4/SF302 FOR VENEER SUPPORT
SF302
3/4" = 1'-0"
GRID
D1
ROOF DECK, SEE PLAN
JOIST, SEE PLAN
MASONRY WALL REINFORCEMENT, SEE PLAN
SHELTER ROOF FRAMING SECTION
TO PARAPET SEE ARCH
D
CMU WALL, SEE PLAN
SEE PLAN
2'-0"
END PLATE
E1
8"x16" POCKET IN 12" CMU WALL
R
3/16
(2) 8" DEEP BOND BEAMS W/ CONT REINF IN EACH, TOP BOND BEAM REINF IS DISCONTINUOUS AT BEAM BEARING, TYP
T O STEEL SEE PLAN
SF301
CONT L6x6x5/16 WITH 3/4"Øx8" SCREW ANCHOR @ 16" OC INTO GROUTED CELLS UNO
T O WALL SEE ARCH
EE
ADDITIONAL CHORD REINFORCEMENT, (4) # 6 CONTINUOUS
SF302
A2
CONT L6x6x5/16 WITH 3/4"Øx8" SCREW ANCHOR @ 16" OC INTO GROUTED CELLS UNO
G IN
T O STEEL SEE PLAN
E5
12" CMU WALL, SEE PLAN FOR REINFORCEMENT
6
(2) #5 CONT IN CMU BOND BEAM
VENEER COORDINATE WITH ARCH FOR LOCATION
DECK, SEE PLAN 3/16
2-6 CONT PL3/8x(MASONRY WIDTH + 8")
3/16
(2) #5 CONTINUOUS IN CMU BOND WALL
VENEER, SEE ARCH
(2) CHANNELS W/ (2) 1/2"Ø THRU BOLTS POST, SEE PLAN
3/16
PL1/2"x5x10 W/ (2) 1/2" Ø THREADED RODS EXPOSED 4" INTO CONC
CHIP OUT MASONRY AND GROUT BELOW BASEPLATE AS REQUIRED TO PROVIDE FLAT BEARING SURFACE. MINIMUM GROUT THICKNESS = 2".
FILL POCKET WITH COMPRESSIBLE FILLER
CMU WALL, SEE PLAN FOR REINF
DECK, SEE PLAN
VENEER COORDINATE WITH ARCH FOR LOCATION
7" MIN BRNG HAND TIGHTEN NUTS ONLY (2) LONG SLOTTED HOLES
1"
4"
(1) #5 CONTINUOUS IN 8" CMU BOND BEAM ((2) #5 CONTINUOUS IN 12" CMU)
FILL POCKET WITH COMPRESSIBLE FILLER
NON-SHRINK GROUT BELOW PLATE
SEE D3/SF302 FOR ADDITIONAL INFORMATION
REBAR SHALL BE CONTINUOUS UNDER BEAM BEARING
PL3/4"x6"x1'-0" W/ (3) 1/2"Øx6" HAS & (2) 3/4"Ø STUD BOLTS
FLUSH PILASTER, SEE PLAN FOR REINFORCING
D6 SF302
NOTE: IF CONCRETE BEAM IS ENCOUNTERED WITHIN WALL, CONTACT ENGINEER OR ARCHITECT IMMEDIATELY FOR RESOLUTION
C3 SECTION
C4 SECTION
3/4" = 1'-0"
EACH BEAM
1/8
SEE PLAN 1"
CONTINUOUS L5x5x1/2 WITH 5/8"Ø x 5" SCREW ANCHORS AT 16" OC
CONTINUOUS L5x3x1/4 LLH WITH 1/2"Øx3 /12" SCREW ANCHOR @ 24" OC INTO BOND BEAM
CONT L5x3x1/4 W/ 1/2"Øx5" SCREW ANCHOR PER S001 @ 16" OC INTO GROUTED BOND BEAM
C5
3/4" = 1'-0"
BEAM BEARING ON CMU WALL 12" 3/4" = 1'-0"
C6
BEAM BEARING ON CMU WALL
PL1/2"x5"x0'-10" WITH (2) 1/2"Øx6" HAS AND (2) 1/2"Ø STUD BOLTS. USE LONG SLOTED HOLES IN BEAM AND HAND TIGHTEN NUTS ONLY
3/4" = 1'-0"
3/4" = 1'-0" L3x3x1/4 @ 2'-0" OC WITH PL1/2"x6"x0'-6" EACH END
200 Longhorn Street Vega, TX 79092
DECK, SEE PLAN VENEER, SEE ARCH
T O WALL SEE PLAN
8"
POUR CONCRETE AROUND BEAM BEARING (1'-4" MAX POCKET WIDTH)
SIZE AND SPACING OF SLAB DOWELS TO MATCH SLAB REINFORCEMENT
T O WALL SEE PLAN
5
VEGA ISD HIGH SCHOOL
VENEER, SEE ARCH ADDITIONAL CHORD REINFORCEMENT, (4) # 6 CONTINUOUS
8" DEEP BOND BEAM WITH (1) #5 CONT
SEE PLAN
L4x4x1/4 EACH SIDE
8" MASONRY WALL WITH #5 @ 24" OC VERTICAL, EMBED REINFORCEMENT 4" INTO CONCRETE WITH ADHESIVE PER S001
4
ST
SHEET METAL OR OTHER CLOSURE, TYP, AT BEAM POCKET DECK, SEE PLAN
E
TO PARAPET SEE ARCH
8" MASONRY WALL WITH #5 @ 24" OC VERTICAL, EMBED REINFORCEMENT 4" INTO CONCRETE WITH ADHESIVE PER S001
8" DEEP BOND BEAM WITH (1) #5 CONT
3
SEE PLAN
TO PARAPET SEE ARCH
2
Dek ke r
1
(2) 1/2"Ø x 4" LAG SCREW #5 U-BAR
CONT L6x6x5/16 LLH W/ 3/4"Ø x 8" EXP ANCHOR @ 16" OC INTO BOND BEAM UNO
1/2"Ø THREADED ROD @16" OC EPOXIED 4" INTO GROUTED CELL. PROVIDE SCREEN @HOLLOW CELL TYP
PROVIDE SSL IN GIRDER FLANGE PARALLEL TO JOIST GIRDER SPAN DECK, SEE PLAN JOIST, SEE PLAN
CMU WALL, SEE PLAN (2) #5 CONT IN CMU BOND BEAM AT DECK ATTACHMENT LOCATIONS
3/16 EXISTING GLUELAM BEAM SEE A3/SF302 FOR INFORMATION
4"
24" MIN
PL1 1/4"x11"x1'-4" W/ (2) 3/4"Ø x 12" EMBED, TYPE "A" ANCHOR RODS PER A3/SB503 1 2" NON-SHRINK GROUT
PROVIDE TIES @ 4" OC IN CONC BEARING CAP
SAWCUT LINE
3"
3/16
EXISTING CMU
4000PSI CONC BEARING CAP
GIRDER BRNG SEE PLAN
EXISTING VENEER 3/16
1/2"Ø THREADED ROD @16" OC EPOXIED 4" INTO GROUTED CELL. PROVIDE SCREEN @HOLLOW CELL TYP
EXISTING VENEER
WF STRONG BACK
B3
B4
SECTION @ WIND GIRT AND EXISTING WALL
OPEN FACES OF BLOCK TO ALLOW FLOW OF CONCRETE FILL
3/4" = 1'-0"
REVISIONS 1
2/4/16
ADDENDUM 001
3
2/11/16
ADDENDUM 004
CONT 6x4x5/16, LLV
3/16 EXISTING VENEER
3/16 3
HSS WIND GIRT, SEE PLAN
8"
1/4" CAP PL, SHOP WELDED TO HSS WITH 3/16" BUTT WELD 1'-0"
TYP. 3/16 L4x4x1/4 x 0'-4" WITH 1/2"Ø THREADED ROD @16" OC EPOXIED 4" INTO EXISTING CMU WALL BOTH SIDES (2 PER CONNECTION)
EXISTING CMU
A1 GIRDER AT PILASTER SECTION 3/4" = 1'-0"
2
L8x6x9/16 SPANNING OPENING, LLH, SEE DETAIL C3/SF503 FOR BEARING ON EACH SIDE OF OPENING
3
2-12
TYP
HSS WIND GIRT, SEE PLAN PL 1"x4"x4" @ 16" OC
3/16
4
3/16
1-12
SECTION @ WIND GIRT AND EXISTING WALL
BB, RW
DECK, SEE PLAN
REVIEWED BY
CH, BB
DATE
14-0424.002
DRAWING NAME
FRAMING SECTIONS
3/4" = 1'-0"
5
01.22.2016
PROJECT NO:
A6 PILASTER SECTION
3/4" = 1'-0"
4
DRAWN BY
MASONRY PILASTER, SEE PLAN FOR SIZE AND REINF
1/4
CONT PL 5/16x8
CONT L5x3x1/4 LLH W/ 5/8"Ø x 4 1/2" EXP ANCHOR @ 24" OC INTO BOND BEAM UNO
(2) #5 CONT IN CMU BOND BEAM AT DECK ATTACHMENT LOCATIONS
CONT PL 3/16x10
A4
A3
CMU WALL, SEE PLAN
1 1/2"
1/2" x 4" LAG SCREW WITH WASHERS IN EACH PLATE WITHIN OVERSIZED HOLE. PL3/8"x4"x"A" @ 2'-0" OC
EXISTING VENEER
2/10/2016 11:35:40 AM
BEAM BEARING ON END OF CMU WALL
1/2"Ø THREADED ROD @16" OC EPOXIED 4" INTO GROUTED CELL. PROVIDE SCREEN @HOLLOW CELL TYP
EXISTING CMU
DO NOT MAKE POSITIVE CONNECTION BETWEEN GIRDER CHORD AND STABILIZING PLATE
1
(3) #7 @ 8" OC WITH #3 TIES @ 8" OC
L3x3x1/4 @ 2'-0" OC WITH PL1/2"x6"x0'-6" EACH END
EXISTING GLULAM BEAM
A
B6
3/4" = 1'-0"
(2) 1/2"Ø x 4" LAG SCREW
BUILT-UP "T" SECTION FROM 3/4" THICK PLATE WITH 1'-0" WIDE FLANGE. ATTACH TO CMU WALL WITH (4) 3/4"Ø x 5 1/2" EXP ANCHORS @ 8" OC
NON-SHRINK GROUT AS REQUIRED FOR COURSING PL1/2"x6"x1'-0" AT 8" CMU; PL1/2"x8"x1'-0" AT 12" CMU WITH (2) 1/2"Ø x 8" HAS
EXISTING CMU
(3) - #5 "U" BAR - 1 AT EACH CELL OF PILASTER
MASONRY PILASTER, SEE PLAN FOR SIZE AND REINF
T O STEEL SEE PLAN
EXISTING CONCRETE MEZZANINE FLOOR TO BE REMOVED
EXISTING CONCRETE
JOIST GIRDER, SEE PLAN 12" DEEP BEARING SEAT - JOIST MANUFACTURER VERIFY
CONT 8x6x7/16 LLH, TOP AND BOTTOM WITH 3/4" A307 THRU BOLT @ 16" OC
3
HSS WIND GIRT, SEE PLAN
B
L2x3x1/4 WITH 1/2"Ø EXP ANCHOR, LONG LEG PARALLEL TO BEAM WEB
6
SHEET NO.
SF302
1
2
3
4
5
6
R2 2
5
E
6'-2"
6'-2"
6'-2"
5'-6"
Z.9
6'-2"
R1
6'-2" 6'-2"
Z
5'-6"
R2
6'-2"
5'-6"
R2
R1.8
R1.8
7'-8"
5'-6"
7'-8"
WIND UPLIFT DIAGRAM BID LOT 4
A6 E1
SB304
WIND UPLIFT DIAGRAM BID LOT 3
SF502 1
E1
5
2
SF502 ARCHITECT
ST
6'-2"
6'-2" 6'-2"
SF502
6'-2"
.7
20 C12x
C1
20 C12x
SF502
S
SI
6'-2"
EE
D NS E EN ON A L I CE
G IN
6'-2"
C1
L
R
85682 E
6'-2"
SF502
i
X
CHARLES R. HANSON OF
D
B1
O F TE
.
RM
SF502 SIM
PR
RM
E AT
n
L td
B1
i ch/Sabat i
S A
SIM
er /P
,
Z
Dek ke r
6'-8"
2/10/2016
F-1092
SIM
PROJECT
.7
A1 SF502
20 C12x
6'-2"
1 6'-0"
T
B6
6'-0"
B1 SB303
SB304
B1 SB301
1
6'-0"
6'-0"
C
C1 LOWER FOUNDATION PLAN - AREA A
0.5
C3 FOUNDATION PLAN - AREA A
1/4" = 1'-0"
1/4" = 1'-0"
11 6'-0"
J R9 R9
6'-0"
H 6'-0"
200 Longhorn Street Vega, TX 79092
.7
VEGA ISD HIGH SCHOOL
.7
SF502 SIM
20 C12x
A1
4" CONCRETE SLAB ON 10 GA PAN WITH L4x4x5/16 STIFFENERS AT 2'-0" OC
6'-0"
6'-0"
6'-0"
" 8'-10
SIM E1
B
SF502
RV
20 C12x
SF502
SIM
B1 SF502
.7
REVISIONS
3 " 8'-10
C1
" 8'-10
.7
20 C12x
20 C12x
SF502
.7
A
A1 SF502
RK
6'-0"
SF502 SIM
A1 SF502
2
2/9/16
ADDENDUM 003
3
2/11/16
ADDENDUM 004
LEGEGEND 28.4 PSF
184 PSF
DRAWN BY
RW
REVIEWED BY
3
RK
26.8 PSF
175 PSF
B1
CH, BB
DATE
01.22.2016
PROJECT NO: " 8'-10
20 C12x
A
ADDENDUM 001
SIM 1
SB301
2/4/16
SF502
B1
C1
1
6'-0"
S
2
20.7 C12x 0 .25 x0 S3 HS
SIM
RN
6'-0"
4" CONCRETE SLAB ON 10 GA PAN WITH L4x4x5/16 STIFFENERS AT 2'-0" OC
E1
RN
6'-0"
20.4 PSF
134 PSF
14-0424.002
DRAWING NAME
.7
ENLARGED PLANS
R3 21.7 PSF
118 PSF
18.3 PSF 2/10/2016 11:35:51 AM
RA 17.2 PSF
A1 LOWER FOUNDATION PLAN - AREA B
A3 FOUNDATION PLAN - AREA B
1/4" = 1'-0"
1
R2
1/4" = 1'-0"
2
3
SHEET NO.
A5 WIND UPLIFT DIAGRAM
SF401
1" = 20'-0"
4
5
6
1
2
3
4
SEE ARCH
#4 x 3'-0" MATCH QUANTITY WITH HORIZONTAL BOND BEAM REINFORCEMENT
PROVIDE LIP IN BRICK TO FIT SUPPORT ANGLE
WRAP PIPE WITH COMRESSIBLE MATERIAL
SPAN (FEET)
SUPPORTED VENEER MAX HEIGHT
LINTEL
0'-0" - 4'-0"
14'-0"
L4x3 1/2x3/8 LLV
4'-1" - 8'-0"
14'-0"
L6x3 1/2x3/8 LLV
8" SQ
NOTES: 1. TABLE IS BASED ON A MAXIMUM SUPPORTED BRICK VENEER INDICATED IN TABLE GREATER HEIGHTS REQUIRE ADDITIONAL DESIGN. 2. SEE DETAIL D1/SF503 FOR ELEVATION. 3. SEE D1/SF503 FOR BRICK TERMINATION AT SILLS AND TOP OF WALL. 4. TIES SHALL BE SEISMIC RATED, SEE SPECIFICATIONS.
E1 LOOSE LINTEL SCHEDULE 3/4" = 1'-0"
1 NOTE: SEE C3 AND D3 ON SF302 FOR INFO NOT SHOWN
HSS12x3x3/16
(E) MASONRY WALL
BOND BEAM REINF
DETAIL B 1/4
T O OPENING SEE ARCH
HSS12x3x3/16
POST, SEE PLAN
FRESH AIR VENT, SEE MECH
STEEL PIPE SLEEVE WITH ID MIN 2" GREATER THAN OD OF PIPE
DETAIL DOES NOT APPLY TO SHELTER, SEE C6/SF503
PL1/2"x6"x10" W/ (2) 1/2"x6" HAS
SHUTTER, SEE ARCH ATTACHMENT PER MFG.
OPENING, SEE ARCH
DOWEL TO MATCH SIZE AND QUANTITY OF WALL REINFORCEMENT TYPICAL EACH SIDE OF OPENING
MAX TIE SPACING= 18" OC VERT & 18" OC HORIZ
CONT ANGLE, SEE SCHED
E
SECTION A
BRICK VENEER, SEE ARCH
LINTEL, SEE PLAN FOR SIZE
6
LINTEL, SEE PLAN
JOINT REINF, SEE SPECIFICATIONS
STUD, SEE PLAN
5
3
ADD CONTINUOUSLY WELDED STEEL SHIMS AS REQUIRED TO OBTAIN TIGHT FIT
DETAIL B
NO PIPES SHALL PASS THRU FOOTING
LAP 40 BAR DIA OR 24" MIN
SECTION A
E3 WALL DETAIL
E2 TYP PIPE PENETRATION 3/4" = 1'-0"
E5 MASONRY DETAIL
3/4" = 1'-0"
E6 STEP IN BOND BEAM
3/4" = 1'-0"
3/4" = 1'-0"
CONTRACTOR TO LOCATE CONC FNDN PRIOR TO STARTING WORK
EA SIM
OPENING, SEE SCHEDULE COORDINATE WITH ARCHITECTURAL
7.
WIDTH OF OPENING B
9. PL1/2"x6x8" CENTERED
D1 LOOSE LINTEL ELEVATION
D3 NEW OPENING IN (E) MASONRY WALL
0" TO 12" OPENINGS
3/4" = 1'-0"
L4x4x1/4 STRONGBACKS ANCHORED TO EXISTING MASONRY WITH 1/2"x6" ADHESIVE ANCHORS AND OPENING AS WELDED TO LINTEL REQUIRED INCLUDING ANGLES WITH 3/16" WELD, MECH DUCT ONLY AT AREAS NOTED ON OPENINGS PER MECH PLAN
EA STUD SEE ARCH
LIPPED MASONRY VENEER SEE SECTION FOR STUD SIZE 24" MAX
BRICK TIE TOP OF WALL/SOFFIT
C
(E) MASONRY WALL (2) #4 x 6'-0" HORIZONTAL CENTERED ABOVE AND BELOW OPENING
24" MAX
GLAZING, SEE ARCH, ATTACH GLAZING TO ANGLE
WELDED ATTACHMENT BY PRECAST MANUFACTURER
(2) #4 x 4'-6" VERTICAL CENTERED EACH SIDE OF OPENING
SEE PLAN
CONT L3x3x3/16 ACCROSS OPENING
SEE SECTION FOR STUD SIZE BRICK TIE
W
LINTEL
B
W
LINTEL
B
≤ 4'-0"
(2) L5x3x1/4
8"
≤ 4'-0"
(2) L6x6x5/16
16"
≤ 6-8"
(2) L7x4x3/8
16"
≤ 6-8"
(2) L8x6x3/8
24"
B
B
1/8
C2
NEW OPENING SECTION A - TYPE 1 8" MASONRY
3/4" = 1'-0"
1/8
C3 TYP OPENING IN (E) 8" CMU
SECTION A - TYPE 2 12" MASONRY OR 8" MASONRY WITH 4" VENEER
(2) VERT IN GROUTED CELL AS SHOWN TO MATCH VERT WALL REINF
HORIZONTAL REINFORCING IN BOND BEAM WITH STANDARD 180° HOOK
CLOSURE PL5/16"xDEPTHx WIDTH OF OPENING
C5 12" CMU WALL END
TYPE 1: SINGLE WYTHE 8" MASONRY WALL.
3/4" = 1'-0"
MARK
DEPTH (D)
BOTTOM REINF
TOP REINF
STIRRUPS & SPACING
ML-1
1'-4"
#5
#5
-
ML-2
5'-4"
#6
#6
#3 @ 32" OC
ML-3
2'-0"
#5
#5
-
(1) VERTICAL IN GROUTED CELL AS SHOWN TO MATCH VERTICAL WALL REINFORCING
HORIZONAL REINFORCING IN BOND BEAM
CORNER BAR TO MATCH SIZE AND SPACING OF HORIZONTAL WALL REINFORCING
(2) VERTICAL IN GROUTED CELL AS SHOWN TO MATCH VERTICAL WALL REINFORCING
CMU FILLER PIECE
LAP SPLICE
B ALTERNATE STIRRUPS
LENGTH
DEPTH (D)
TOP REINF
VERTICAL REINFORCING, SEE SCHEDULE WIDTH
8" NOMINAL OR 12" NOMINAL
ALL LINTELS SHALL BE CLOSED BOTTOM LINTEL BLOCKS
LINTEL DETAIL 40 BAR Ø
OPENING,
2'-0" MIN
SEE ARCH LINTEL DETAIL
LENGTH
MP-1 MP-2
2/10/2016 2:03:56 PM
A
WIDTH
VERT REINF
TIES
SEE D5/SF503 1
16"
12"
(4) #5
#2 @ 8" OC
NOTES: 1. PROVIDE FOUNDATION DOWELS TO MATCH AND LAP VERTICAL PILASTER REINFORCING. 2. GROUT SOLID ALL MASONRY CELLS WITHIN PILASTER LENGTH. 3. WHERE PILASTER OCCURS NEXT TO MASONRY OPENING, LINTEL REINFORCING SHALL EXTEND INTO PILASTER AS INDICATED ON CMU WALL REINFORCING DIAGRAM. JAMB REINFOCRING SHALL BE ELIMINATED TO ALLOW FOR PLACEMENT OF CONTINUOUS PILASTER REINFORCING. 4. PILASTER TIES ARE IN ADDITION TO BOND BEAM REINFORCING AND HORIZOTAL JOINT REINFORCING.
A1
MASONRY PILASTER REINFORCING 3/4" = 1'-0"
2
FLOOR LEVEL BOND BEAM. SEE CMU WALL REINF DIAGRAM.
3
EXTEND GROUTED LINTEL 40 BAR DIAMETER (A MINIMUM OF 2'-0") BEYOND FACE OF OPENING EACH SIDE FOR STRAIGHT LINTEL REINF AND 1'-4" FOR LINTEL REINF WITH STANDARD ACI HOOK.
1'-4" MIN
5
USE LINTEL BLOCKS ONLY FOR BOTTOM COURSE OF LINTEL BEAMS.
5
CONTINUE VERT WALL REINF OVER OPENING. ANCHOR VERT REINF INTO LINTEL BEAM WITH STANDARD ACI HOOK.
6
BOND BEAM EXTENDED 24" BEYOND FACE OF REINF WITH (1) #4 UNO.
7
STIRRUP, SEE SCHEDULE FOR SIZE AND SPACING.
8
TURNED DOWN SLAB EDGE AT FLOOR LEVEL OPENINGS.
GROUT ALL REINF CELLS AND CONTINUE REINF TO FULL HEIGHT OF WALL, TYP
1 OPENING, SEE ARCH
TYPE
SEE CMU WALL REINF DIAGRAM FOR SPLICES IN VERT REINF.
3
MASONRY PILASTER SCHEDULE MARK
1
4
7
TYPE 1
NOTE: ALL HORIZONTAL REINFORCING IN BOND BEAMS SHALL BE CONTINUOUS AROUND CORNER OR HAVE CORNER BARS OF THE SAME SIZE AND LAP OF 48 BAR DIAMETERS OR 24" MINIMUM.
KEYED NOTES
BOTTOM REINF
TIES, SEE SCHEDULE
4
JAMB DETAIL
T O SLAB SEE PLAN
GROUT SOLID AFTER INSTALLATION
BOND BEAM W/ CONT REINFORCEMENT ABOVE & BELOW OPENINGS
NOTE: THESE SIDEWALL DETAILS SHALL BE USED IN THE SHELTER ENVELOPE, COORDINATE EXACT LOCATION WITH MEP
C6
SECTION
MASONRY WALL, SEE SECTIONS & DETAILS
MASONRY WALL, SEE SECTIONS AND DETAILS
STRUCTURAL SIDEWALL PIPE PENETRATION DETAIL 3/4" = 1'-0"
B4 12" CMU WALL CORNER 3/4" = 1'-0"
SPLICE VERTICAL BARS PER C3/SB503, OR WITH MECHANICAL COUPLERS WHICH DEVELOP 125% OF ASTM SPECIFIED YIELD STRENGTH WHEN CLEARANCES ARE LIMITED. (LAP WITH FOOTING DOWELS PER C3/SB503)
B5
R
EE
REVISIONS
PLACE MORTAR ON CROSS WEBS ADJACENT TO CELLS WHICH WILL BE GROUTED TO PREVENT LEAKAGE
3/4" = 1'-0"
(1) VERT IN EACH OF 4 GROUTED CELLS AS SHOWN TO MATCH VERT WALL REINFORCING
(1) VERTICAL IN EACH OF 3 GROUTED CELLS AS SHOWN TO MATCH VERTICAL WALL REINFORCING
REINFORCING SYMBOL FROM PLAN
12S(2)532P
NOMINAL THICKNESS OF CMU IN INCHES 8 - 8" CMU WALL 12 - 12" CMU WALL CODE FOR HORIZONTAL REINF AS FOLLOWS: S - STANDARD TRUSS TYPE 9 GA JOINT REINF @ 16" OC MAX A - #5 @ 32" OC IN GROUTED BOND BEAM
SEE PLAN FOR CONTINUOUS AROUND CORNER JOINT REINFORCING
SEE PLAN FOR JOINT REINFORCING
1
2/4/16
ADDENDUM 001
3
2/11/16
ADDENDUM 004
A4
TYPICAL 8" CMU WALL CORNER 3/4" = 1'-0"
4
A5
FOOTING OR GRADE BEAM
TYPICAL 8" CMU WALL INTERSECTION 3/4" = 1'-0"
5
P - PARTIALLY GROUTED WALL. GROUT WALL AT REINFORCED CELLS ONLY S - SOLID GROUT WALL. GROUT ALL CELLS INCLUDING CELLS WITHOUT VERTICAL REINFORCING CODE FOR VERTICAL REINFORCING AS FOLLOWS: FIRST DIGIT IS BAR SIZE, NEXT TWO INDICATE SPACING IN INCHES CODE INDICATING TWO VERTICAL REINFORCING BARS ARE REQUIRED
BOND BEAMS SHALL BE REINFORCED (1) #5 HORIZONTAL IN 8" CMU AND (2) #5 CONTINUOUS IN 12" CMU UNLESS NOTED OTHERWISE. BOND BEAMS ARE REQUIRED AT FIRST COURSE ABOVE FOOTING, AT FINISHED FLOOR ELEVATION, AT FIRST FULL COURSE BELOW JOIST/BEAM BEARING, AT COURSE PARALLEL WITH DECK EDGE ANGLE, AT TOP OF WALLS, AND AT ALL OTHER LOCATIONS SHOWN ON PLAN OR IN DETAILS.
JAMB DETAILS (UNO ON PLAN)
3
1
HORIZONTAL JOINT REINFORCING PER SYMBOL
12" CMU WALL INTERSECTION
6
A2 TYPICAL MASONRY WALL OPENING
G IN
CELLS CONTAINING STEEL ARE FILLED WITH GROUT UNO; VERTICAL CELL SHOULD PROVIDE A CONTINUOUS CAVITY FREE OF MORTAR DROPPINGS AND AT LEAST 3"x4" IN SIZE. AT TOP OF INTERMEDIATE GROUT LIFTS, HOLD GROUT 2" BELOW TOP OF BLOCK. GROUT ALL CELLS SOLID BELOW GRADE. ALL REINFORCED CELLS ARE GROUTED
LOW LIFT-GROUTING TECHNIQUE, GROUT IS PLACED IN LIFTS TO 4'-0" MAX
GROUT ALL REINF CELLS & CONTINUE REINF TO FULL HEIGHT OF WALL, TYP
2'-0"
NOTE: VERTICAL REINFORCING FULL HEIGHT OF WALL
VERTICAL REINFORCING PER SYMBOL, BOND BEAM REINFORCING PER NOTE
OPENINGS LARGER THAN 8'-0"
2
1/4" FLANGE PLATE, EACH SIDE
REINFORCING CENTERED IN BLOCK CAVITY (UNO)
2
3/4" = 1'-0"
1
MASONRY CONTROL JOINT
CMU WALL REINF, UNO. PROVIDE (1) BAR EACH CELL. SIZE OF BARS TO MATCH VERT
OPENINGS UP TO 8'-0"
2/10/2016
HOLD REINF IN POSITION AT INTERVALS OF 96 BAR DIAMETERS (MAX WITH "REBAR POSITIONERS" (MIN OF 2 PER BAR) ALL REINF SHALL BE ANCHORED IN POSITION PRIOR TO PLACING GROUT
1'-4"
8
SHELTER CONSTURCTION, SEE PLAN & SECTIONS
TYPE 2: SINGLE WYTHE 12" MASONRY WALL OR SINGLE WYTHE 8" WALL WITH 4" VENEER.
VERTICAL WALL REINFORCING
NOTE: BOND BEAM REINFORCING AND HORIZONTAL JOINT REINFORCING NOT SHOWN FOR CLARITY.
3/4"Ø THRU-BOLT, TOP & BOTTOM
3/4" = 1'-0"
CMU LINTEL SCHEDULE
D NS E EN ON A L I CE
3/4" = 1'-0"
ELEVATION
2-12
CONTRACTOR TO IDENTIFY IN THE FIELD THE WALL TYPE FOR EACH OPENING IN EXISTING WALLS.
SI
D6 MASONRY CONTROL JOINT
SEE ARCH
CLOSURE PL3/16"x7"x WIDTH OF OPENING
CONSTRUCTION SEQUENCE 1. ROUT MORTAR JOINT TO HALF WALL DEPTH AND INSERT FIRST ANGLE. 2. ROUT OPPOSITE JOINT AND INSERT SECOND ANGLE. 3. SAWCUT CMU FOR OPENING AND REMOVE. 4. ATTACH CLOSURE PLATE TO ANGLES.
PLAN
SEE SCHEDULE EACH SIDE
2-12
S
SEE ARCH FOR JOINT SEALANT (BOTH SIDES)
4" TYP
(E) VENEER
SEE ARCH
W
(1) VERTICAL IN EACH OF 2 GROUTED CELLS AS SHOWN TO MATCH VERTICAL WALL REINFORCING
NOTE: TOP OF OPENING SHALL NOT BE WITHIN 2'-0" OF BEAM BEARING OR 2'-8" BELOW CONCRETE SLAB PIPE PROTECTION, SEE SECTION, TYP
(E) CMU WALL
85682 L
PROJECT
(E) MASONRY LINTEL SCHEDULE TYPE 2
SEE SCHEDULE EACH SIDE
TYPICAL CMU OPENING 2'-0" MAX
AT SILL
3/4" = 1'-0"
A
1'-4"
3/4" = 1'-0"
(E) CMU WALL
12" TO 24" OPENINGS
C1 BRICK TERMINATION
(E) MASONRY LINTEL SCHEDULE TYPE 1
NOTE: OPENING MUST BE AT LEAST 4'-0" AWAY FROM JAMBS, LINTELS, OR MASONRY CONTROL JOINTS.
EA STUD SEE ARCH
CONT L3x3x3/16, ATTACH VENEER TO ANGLE
6'-0" TYP
CONT L4x4x3/16
1'-4"
D5 MP-1 MASONRY PILASTER
3/4" = 1'-0"
CHARLES R. HANSON
SEE PLAN FOR JOINT REINFORCING, DISCONTINUE JOINT REINFORCING AT MCJ
F-1092
B
DETAIL B-B
ATTACH VENEER TO ANGLE W/ METAL WALL TIE
8.
i
X
200 Longhorn Street Vega, TX 79092
SHIM AS REQ'D
2 1/2" CLR, TYP
O F TE
VEGA ISD HIGH SCHOOL
TEMP SUPPORT
6.
E AT
n
{
D
PREFORMED CONTINUOUS NEOPRENE EXPANSION JOINT
4" TYP
(2) #4 x 3'-0" HORIZONTAL CENTERED ABOVE AND BELOW OPENING
ELEVATION
SEE SCHEDULE
BRICK VENEER
5.
i ch/Sabat i
.
HSS8x2x1/4 TYP
12" MAX
4.
E
FOR EXTENTS
DETAIL A-A
2"
er /P
OF
SEE ARCH
ARCHITECT
PR
2"
VERTICAL WALL REINFORCING
ST
2"
SEE ARCH FOR EXTENTS
2"
#3 TIES @ 8" OC
Dek ke r
8"
BOND BEAM REINFORCING
1'-0" LAP
SHELTER CONSTRUCTION
A
(8) #7 VERTICAL
CARDBOARD SLEEVE, TAPE END OF SLEEVE AND GREASE DOWEL
1 1/2" TYP
3.
MASONRY / BRICK VENEER WALL
HSS8x2x1/4
(2) #4 x 2'-0" VERTICAL CENTERED EACH SIDE OF OPENING
2"
ANGLE LINTEL
GRID
L td
SF503
2.
ROUT MORTAR JOINT THROUGH WALL DEPTH FOR LENGTH OF NEW OPENING PLUS DISTANCE SHOWN EACH SIDE. INSERT ANGLES EACH SIDE CENTERED OVER NEW OPENING IN ROUTED MORTAR JOINT. INSERT PLATE UNDER ANGLES IN ROUTED MORTAR JOINT AT NEW OPENING. WELD PLATE TO ANGLES AS SHOWN IN DETAIL C3/SF503. SAWCUT THOUGH MASONRY AND BRICK WALL FROM EACH SIDE AT CENTER OF NEW OPENING; INSTALL TEMPORARY SUPPORT. SAWCUT THROUGH MASONRY AND BRICK WALL FROM EACH SIDE AT JAMB LOCATIONS, REMOVE MASONRY INSIDE NEW OPENING EXTENTS. INSTALL BASEPLATES AT LOCATIONS AS SHOWN IN DETAIL B-B. INSERT VERTICAL 8"x2" HSS AT EACH SIDE OF OPENING, AT ANGLE BEARING AS SHOWN IN DETAIL A-A. WELD HSS TO ANGLE LINTEL AND BASEPLATES AS SHOWN IN THE DETAILS. REPAIR SLAB PER A2/SB501.
,
E1
NOTE: COORDINATE LOCATION AND SIZE OF OPENING WITH ARCHITECTURAL
1.
A
S A
LINTEL SUPPORT ANGLE, SEE E1/SF503
8" MAX
4" BEARING TYP
PLATE WIDTH OF OPENING
CONSTRUCTION SEQUENCE:
2 1/2" CLR, TYP
ANGLE PER DETAIL C3/SF503, EACH SIDE
OPENING AS REQUIRED INCLUDING "GLASS BLOCK" LOCATIONS PER ARCH
TRANSVERSE WALL
CONTRACTOR TO VERIFY
2'-0"
12" = Wt
A6
TYPICAL REINFORCED CONCRETE MASONRY CONSTRUCTION 3/4" = 1'-0"
6
DRAWN BY
BB, RW
REVIEWED BY
CH, BB
DATE
01.22.2016
PROJECT NO:
14-0424.002
DRAWING NAME
MASONRY DETAILS
SHEET NO.
SF503
1
2
3
4
5
6
GENERAL SHEET NOTES
D. E. F. G. H. I. J.
E K.
S
R EG I
C H ARL E 18563
OF
TE
X
ARCHITECT
10" 17' -
6" 65' 0" 10' -
R3
D
TE
Y L OR
20
A5 / AE100A
C
R6
R5
MATCHLINE
T
EC T
T
R8
AR
R BAR E T
TA
S A
R9
ED
IT
REFERENCE KEYNOTES
ER
H
ST
L.
S
B. C.
ALL PLAN DIMENSIONS ARE TO FACE OF STUD, FACE OF CMU, OR CENTER OF COLUMN UNLESS NOTED OTHERWISE. REFER TO EXTERIOR ELEVATIONS FOR LOCATIONS, TYPE AND FINISH OF ALL EXTERIOR WALLS. ABUSE RESISTANT GYPSUM BOARD TO BE INSTALLED ON ALL HALLWAY, LOBBY, VESTIBULE, AND STORAGE ROOM WALLS UNLESS NOTED OTHERWISE. REFERENCE FINISH FLOOR ELEVATION = 100'-0" (MSLE). REF: CIVIL DRAWINGS FOR MSLE. REFER TO INTERIOR ELEVATIONS FOR INSTRUCTION SURFACE MOUNTING HEIGHTS. ALIGN NEW FINISHES WITH EXISTING WHERE APPLICABLE, TAPE AND TEXTURE. ALL GYPSUM BOARD CORNERS TO RECEIVE FULL HEIGHT CORNER GYPSUM BOARD CORNER GUARDS. ALL GYPSUM CEILING CORNERS TO RECEIVE FULL LENGTH CORNER GUARDS. FINAL LOCATION OF PAPER TOWEL DISPENSER TO BE COORDINATED WITH ARCHITECT. MASONRY JOINT LOCATIONS: EQUALLY SPACED ON MASONRY DIMENSIONS, WITH SPANS NOT TO EXCEED 20'-0" O.C. COORDINATE WITH ARCHITECT PRIOR TO FABRICATION. COORDINATE LOCATION WITH TILE JOINTS. ALL EXPOSED INTERIOR CMU WALLS TO BE PAINTED. COLOR TO BE SELECTED BY ARCHITECT. REFER TO INTERIOR FINISH SHEETS. GYPSUM CONTROL JOINT LOCATIONS: SPANS NOT TO EXCEED 20'-0" O.C. COORDINATE LOCATIONS WITH ARCHITECT PRIOR TO FABRICATION / INSTALLATION. COORDINATE LOCATIONS WITH TILE JOINTS. BASKETBALL COURT STRIPING IS SHOWN FOR REFERENCE ONLY. REFER TO INTERIOR FINISH SHEETS.
A
A.
WHIRLPOOL 0" 27' -
6
PROJECT 7" 27' -
6
TRAINING
8" 10' -
B116
ICE MACHINE
A5 B B112
AE402
GIRLS JV
4 B113
B111
D
B116
B111
FILM ROOM
ELEC
10" 32' -
7" 10' -
B114
B107
B121
JANITOR COACH RR
RS
B121
B115
B109
0" 10' -
C1
ELEV
AE451
2" 45' -
D
BOYS COACH
5" 17' -
B119
UNIFORM STOR B120
B B123
" 7' - 4
B122
B124 A B123
INTERIOR ELEVATIONS B127
XX-XXX
X
TACKBOARD, REFER TO INTERIORS
TB-1, TB-2, ETC.
MARKERBOARD, REFER TO INTERIORS
MB-1, MB-2, ETC.
FORBO TACKWALL, REFER TO INTERIORS
TW-1
B132 B131
B133
" 8' - 0
BOYS VISITOR B131
6"
" 3' - 6
4
100% BID DOCUMENTS
EXISTING TO REMAIN
2" 16' -
" 6' - 2
" 5' - 7
B128
" 4' - 0
EXISTING TO REMAIN
REVISIONS
Addendum 004 - 02.15.2016
A5
GIRLS VISITOR
AE401
B133
B129
RG
X
X
CORRIDOR
B132
4
XX-XXX
9" 24' -
4" 11' -
" 7' - 0
XX-XXX
IT 4
0" 10' -
0" 27' -
RJ
XX
X
B
AE301
BUILDING SECTION / WALL SECTION
EXTERIOR ELEVATIONS
4
B127
A5
1i XX
XX
0" 12' -
B122
8" 67' -
BOYS JV
B123
PARTITION ASSEMBLY TYPE
CORRIDOR
BOYS VARSITY
BOYS
XX
STAIR 1
B124
9" 10' -
B118
RK
WINDOW TYPE
B126
FILM ROOM
RN
LEGEND
W
8" 10' -
B120
2"
D2 B118
B119
" 7' - 0
AE451
B106
" 8' - 0
B102 B106
CORRIDOR
0" 21' -
" 9' - 3
B109
PA
B117 112'
" 6' - 0
C
B117
2A
B115
B108
AE301
B107
B108
8" 10' -
B2
ELEC
4
GIRLS COACH
RR
2" 13' -
B114
W
GIRLS VARSITY
UNIFORM STOR
200 Longhorn Street Vega, TX 79092
B112
8" 16' -
A B112
XRB
VEGA ISD HIGH SCHOOL
B113
GIRLS
OFFICIALS
KEY PLAN - NTS
B128 10" 23' 8" 11' -
OFFICIALS RR
RE
8" 41' -
B129
DRAWN BY
KLS
REVIEWED BY
CBT
DATE LEVEL 1 ABOVE
01.21.2016
PROJECT NO:
14-0424.002
DRAWING NAME
A
LOWER LEVEL FLOOR PLAN AREA B
AREA B AREA A
2/15/2016 4:57:07 PM
0A AE10 A5 /
1
2
3
NORTH
A5 4
LOWER LEVEL FLOOR PLAN - AREA A 1/8" = 1'-0"
0'
5
4'
8'
SHEET NO.
NORTH
AE100B
16'
6
2
3
4
5
6
GENERAL SHEET NOTES
E5 AE201
1.9
2
3
A.
4
5
5.1
B. C. D. E. F. G. H. I.
BID LOT #4, RE: D2/AE101C 77' - 4"
J.
E K.
Z
L. VEST
ALL PLAN DIMENSIONS ARE TO FACE OF STUD, FACE OF CMU, OR CENTER OF COLUMN UNLESS NOTED OTHERWISE. REFER TO EXTERIOR ELEVATIONS FOR LOCATIONS, TYPE AND FINISH OF ALL EXTERIOR WALLS. ABUSE RESISTANT GYPSUM BOARD TO BE INSTALLED ON ALL HALLWAY, LOBBY, VESTIBULE, AND STORAGE ROOM WALLS UNLESS NOTED OTHERWISE. REFERENCE FINISH FLOOR ELEVATION = 100'-0" (MSLE). REF: CIVIL DRAWINGS FOR MSLE. REFER TO INTERIOR ELEVATIONS FOR INSTRUCTION SURFACE MOUNTING HEIGHTS. ALIGN NEW FINISHES WITH EXISTING WHERE APPLICABLE, TAPE AND TEXTURE. ALL GYPSUM BOARD CORNERS TO RECEIVE FULL HEIGHT CORNER GYPSUM BOARD CORNER GUARDS. ALL GYPSUM CEILING CORNERS TO RECEIVE FULL LENGTH CORNER GUARDS. FINAL LOCATION OF PAPER TOWEL DISPENSER TO BE COORDINATED WITH ARCHITECT. MASONRY JOINT LOCATIONS: EQUALLY SPACED ON MASONRY DIMENSIONS, WITH SPANS NOT TO EXCEED 20'-0" O.C. COORDINATE WITH ARCHITECT PRIOR TO FABRICATION. COORDINATE LOCATION WITH TILE JOINTS. ALL EXPOSED INTERIOR CMU WALLS TO BE PAINTED. COLOR TO BE SELECTED BY ARCHITECT. REFER TO INTERIOR FINISH SHEETS. GYPSUM CONTROL JOINT LOCATIONS: SPANS NOT TO EXCEED 20'-0" O.C. COORDINATE LOCATIONS WITH ARCHITECT PRIOR TO FABRICATION / INSTALLATION. COORDINATE LOCATIONS WITH TILE JOINTS. BASKETBALL COURT STRIPING IS SHOWN FOR REFERENCE ONLY. REFER TO INTERIOR FINISH SHEETS.
153
Y.9 Y
CLASSROOM
CLASSROOM
149
148
STOR STOR
CORRIDOR
148A STOR
ST R EG I
98' - 8"
146
REFERENCE KEYNOTES
T
A
W.1 W
145
TE
18563
OF
TE
X
ARCHITECT
BOYS
GIRLS
C
Y L OR
CLASSROOM
147
T
EC T
CLASSROOM
S
W.2
AR
R BAR E T
TA
X
ED
IT
147A
ER
H
146A
S
STOR
S
152
A
149A
C H ARL E
1
144
STAFF RR
143
V
ELEC
STOR
150
IDF
137A
141
U
JAN
VEST
139
142
F CORRIDOR STOR
138
136A
SPEC ED
137
T
184' - 0"
1
D
CLASSROOM
136
PROJECT
S
LAB
135
R Q
CLASSROOM
134
T
N
C5
MECH
F154 F
STOR/PREP
STOR
133
134A
AE201
STOR
T
132A
M CLASSROOM
132
0.5
L
LAB
131
MATCHLINE
A5 / AE101C A5 / AE101B
7
STOR
130B
J
130
CLASSROOM
129
C
11 12
LIFESKILLS
54' - 8"
RR
130A
F
2448
2472
128A
G.9
2472
STOR
STOR
STOR
129A
128B
STOR
125A
2472
51' - 4"
H
2448
WARMING KITCHEN
A5 / AE101B
MEDIA CENTER
ART
125
123
128
MATCHLINE
LEGEND
CONCESSION
A5 / AE101A
127
G
R1.8
- 4" 101'
KILN
123A
COMPUTER LAB
119 BOYS
RT FILM
XX
D.2
117A
102
XX EXTERIOR ELEVATIONS
F
RE SCO ER P KEE
JANITOR
CORRIDOR
120
117
X INTERIOR ELEVATIONS
CLASSROOM
FAM RR
116 M W
TEST STOR
STOR
122B
122A
115A
XX-XXX
122C
STAGE
AUDITORIUM
A124
A119
X
X
OFFICE
115
X
EXISTING 6'-0" (VERIFY) OPENING TO REMAIN PROVIDE NEW PAIR OF 90 MIN. RATED DOORS AND FRAME
122
104
ELEV
TACKBOARD, REFER TO INTERIORS
TB-1, TB-2, ETC.
MARKERBOARD, REFER TO INTERIORS
MB-1, MB-2, ETC.
FORBO TACKWALL, REFER TO INTERIORS
TW-1
M
RN
RS
XX-XXX
D CORRIDOR
RV
XX-XXX
A132
ELEC
STUDENT COMMONS
RR
B
BUILDING SECTION / WALL SECTION
E
CORRIDOR
118
156
1i XX
F
123B
121
GIRLS
TRACK
PARTITION ASSEMBLY TYPE
14
F
STOR
3.1 R2.1
XX
VEST
124
R2
WINDOW TYPE
W FILES CONF
112
108
113
103A
GYMNASIUM
STOR
CORRIDOR
RK
EXISTING TO REMAIN
C
106
EXISTING TO REMAIN
WORKROOM ISS
RQ
100% BID DOCUMENTS
111
B100
REVISIONS
109
41
107 NURSE
RJ
B
VEST
100
KEY PLAN - NTS
VEST
101
169
A
STOR
138'
164
4"
RM
109A
PRINC
105
RG
STAIR 2
A125
LOUNGE
RECEPTION
103
8
R8.2
RE
8.8
9
13 15 16
RD AREA C 8" 49' -
RB A
RF
R6
R5
FILM
120'
4"
R2.9
R8.1
REVIEWED BY
CBT
DATE
EXST TO REMAIN
MATCH LINE
01.21.2016 14-0424.002
DRAWING NAME
LEVEL 1 FLOOR PLAN AREA A A5 1 AE20
NORTH
4
NORTH
LEVEL 1 FLOOR PLAN 1/16" = 1'-0"
0'
5
8'
16'
32'
INE CH L MAT
3
KLS
PROJECT NO:
A5 2
DRAWN BY
AREA B
1B AE10 A5 / 1A AE10 A5 /
2/16/2016 11:00:22 AM
R7 R8
PROPOSED NEW
R9
EXISTING
R3
RA 1
Date 1 Revision ADDENDUM 004 -1 02.15.2016
PROP STOR
114
BID LOT #3, RE: A1/AE101A
200 Longhorn Street Vega, TX 79092
AE201
VEGA ISD HIGH SCHOOL
64' - 0"
P
B5
SHEET NO.
AE101 6
1
2
3
4
5
6
GENERAL SHEET NOTES A.
5
11' - 2"
B. C. D. E. F. G.
31' - 6"
H. I.
A5 / AE101C MATCHLINE
MB-1
125B
130A
129
128B
11' - 4"
6' - 9"
40' - 6"
26' - 3"
INTERIOR ARCHITECTURAL JOINT SYSTEM (EJ-01) EXTERIOR ARCHITECTURAL JOINT SYSTEM (EJ-2) KILN, OPCI THERAPY SWING CLEAR AREA, REFER TO RCP FOOD SERVICE EQUIPMENT
ED
AR
R BAR E T
T
C
A
TE
18563
OF
TE
X
ARCHITECT
16' - 6"
ART 123
125
TB-3
A134
46' - 11"
2A 2
MEDIA CENTER
6' - 1"
1' - 2"
2
2
127
07 9500.01 07 9500.02 10 9600.02 10 9600.04 11 4000.01
2A
12A
16' - 5"
ER
STOR
9A
CONCESSION
12B
REFERENCE KEYNOTES
A135
3' - 1" 2' - 6"
2
2
A5 / AE101A KA
4' - 10"
126
128
MATCHLINE
5' - 10"
MAINTENANCE
AE222
1' - 9"
4' - 11"
5' - 11"
WARMING KITCHEN
125A
AF404
2
2448
2
AE302
C1
35' - 6"
127
E2
2A
C5
D
2472
2472
2472
129A
2448
6' - 9"
128B
2
MB-1
125A
STOR
2
AE202
Y L OR
2
E1
A3
EC T
STOR
9A
STOR
H (ABOVE)
(ABOVE)
T
2 11 4000.01 128A
AF404 H
TA
9A
TB-3
2' - 8"
B2
AE401
17' - 0"
FE
2A
E4
23' - 4"
S
G.9
2
STOR
130
130A
ST
RR
15' - 3"
LIFESKILLS
IT
H
A
130B
TW-1
5' - 2"
" 60
MB-4
3' - 1"
L.
R EG I
R
130B
8' - 10"
TB-1
129A
STOR
2
2
4' - 8"
12
H
4' - 4"
2A
11
10 9600.04
1' - 0 1/8"
129
2
10
2
23' - 3"
6' - 4"
CLASSROOM
2 13' - 5"
5' - 6"
2
13
7
2A
2
130
129B
K.
8' - 0"
1A
MB-1
TB-1
J.
7' - 3"
5' - 7"
J
1
MB-1
FE
E
10' - 8"
FE
10
S
10"
39' - 4"
4
AE302
A
A5
3
S
1
C H ARL E
0.5
ALL PLAN DIMENSIONS ARE TO FACE OF STUD, FACE OF CMU, OR CENTER OF COLUMN UNLESS NOTED OTHERWISE. REFER TO EXTERIOR ELEVATIONS FOR LOCATIONS, TYPE AND FINISH OF ALL EXTERIOR WALLS. ABUSE RESISTANT GYPSUM BOARD TO BE INSTALLED ON ALL HALLWAY, LOBBY, VESTIBULE, AND STORAGE ROOM WALLS UNLESS NOTED OTHERWISE. REFERENCE FINISH FLOOR ELEVATION = 100'-0" (MSLE). REF: CIVIL DRAWINGS FOR MSLE. REFER TO INTERIOR ELEVATIONS FOR INSTRUCTION SURFACE MOUNTING HEIGHTS. ALIGN NEW FINISHES WITH EXISTING WHERE APPLICABLE, TAPE AND TEXTURE. ALL GYPSUM BOARD CORNERS TO RECEIVE FULL HEIGHT CORNER GYPSUM BOARD CORNER GUARDS. ALL GYPSUM CEILING CORNERS TO RECEIVE FULL LENGTH CORNER GUARDS. FINAL LOCATION OF PAPER TOWEL DISPENSER TO BE COORDINATED WITH ARCHITECT. MASONRY JOINT LOCATIONS: EQUALLY SPACED ON MASONRY DIMENSIONS, WITH SPANS NOT TO EXCEED 20'-0" O.C. COORDINATE WITH ARCHITECT PRIOR TO FABRICATION. COORDINATE LOCATION WITH TILE JOINTS. ALL EXPOSED INTERIOR CMU WALLS TO BE PAINTED. COLOR TO BE SELECTED BY ARCHITECT. REFER TO INTERIOR FINISH SHEETS. GYPSUM CONTROL JOINT LOCATIONS: SPANS NOT TO EXCEED 20'-0" O.C. COORDINATE LOCATIONS WITH ARCHITECT PRIOR TO FABRICATION / INSTALLATION. COORDINATE LOCATIONS WITH TILE JOINTS. BASKETBALL COURT STRIPING IS SHOWN FOR REFERENCE ONLY. REFER TO INTERIOR FINISH SHEETS.
1
FF TO MATCH EXISTING:98' - 8"
STOR
B2
COMPUTER LAB 9" 22' -
8
110
118
ELEC 121A
122
" 8' - 6
B5 AE501
AE451
AE401
AE451
M
115
122D
" 2' - 8
OFFICE
10
115A
STOR
122B
W
10
108 1" 7' - 1
2
2
" 9' - 4
0" 18' -
CORRIDOR ISS
114
INTERIOR ELEVATIONS
101C
164
VEST
RG
14A
101
WORKROOM
A3 2
AF403
PROP STOR
" 2' - 8
5' - 5"
TACKBOARD, REFER TO INTERIORS
TB-1, TB-2, ETC.
MARKERBOARD, REFER TO INTERIORS
MB-1, MB-2, ETC.
FORBO TACKWALL, REFER TO INTERIORS
TW-1
6' - 8"
F
100B
100A
B
RAMP UP: 1/12 SLOPE
D3
VEST
AE452
100
B 6' - 0"
6' - 8"
10' - 6"
6' - 8"
101A
4" 30' -
" 1' - 0
14B
7
ADDENDUM 004 - 02.15.2016
6' - 8"
E 15 6' - 8"
6' - 8"
6' - 8"
KEY PLAN - NTS
2' - 10"
67' - 0"
2" 10' -
B1 AE302 B5
1" 13' -
R8.2
R6
AE302
8
8.8
9
13
16
AREA C
4
R9
A 0" 40' -
R8
MATCH LINE
R8.1
PROPOSED NEW
RB
AE301
E5
R2.9
01.21.2016 14-0424.002
AREA B AREA A NORTH
A5
D5 3 AE20
3
4
LEVEL 1 FLOOR PLAN - AREA B 1/8" = 1'-0"
0'
5
4'
8'
16'
NORTH
INE CH L MAT
R3
CBT
LEVEL 1 FLOOR PLAN - AREA B
R6
1A AE10 A5 /
RA
R5
REVIEWED BY
DRAWING NAME
EXST TO REMAIN
AE203 D5
KLS
PROJECT NO:
AE501
R7
DRAWN BY
DATE
E4
AE501
R8
2/12/2016 11:09:21 AM
EXISTING
D6
R7
2
REVISIONS
A
E
07 9500.02
EXISTING TO REMAIN
1' - 0"
R5
1
100% BID DOCUMENTS
EXISTING TO REMAIN
07 9500.01
LEVEL 1 FF: 100'-0"
AF403
4" 30' -
R4
3
109A
9A
B
164
R3
LOUNGE
2
A1/A2
STOR
R2
FF: 98' - 8"
RECEPTION 103
X
X
FF: 95' - 2"
109
18' - 5"
103
XX-XXX
1
109A 8
X
106
FE " 1' - 6
" 1' - 6
FE
AE301
XX-XXX X
2A
105
8" 20' -
A5
XX-XXX
EXTERIOR ELEVATIONS
105
2
XX
A125
PRINC
2
BUILDING SECTION / WALL SECTION
XX
RJ
111
107
156A
1i XX
STOR
CORRIDOR
107
" 2' - 8
2
NURSE
A119
PARTITION ASSEMBLY TYPE
111
2A
104
A124
XX
C 109
" 6' - 1
2" 10' -
19
AUDITORIUM
" 7' - 8
2
103D
112
10' - 2"
113 113
103B
2
FILES
0" 9' - 1
103A 103C
" 2' - 8
4" 18' -
4" 17' -
CONF
W 10
STAGE
WINDOW TYPE
112
10
10
MB-1
A1
LEGEND
2
M 108
4" 17' -
" 2' - 8
" 2' - 3
2
1
122C
122A
MB-1
EXST BO AUDITORIUM:95' - 2"
FF: 98' - 8"
2A
15' - 0"
" 9' - 9
9A
122C
2
A1
122B
9
RK
C2
10
D3
1
5" 17' -
" 2' - 4
115A
AF404
SIM.
RD
D
2
CLASSROOM
1
114
RE
2
122
103A
RF
RAMP UP: 1/12 SLOPE
10" 19' -
1
115
9A
R1
RAMP UP: 1/12 SLOPE
MB-4
TEST STOR
RM
E
FF: 98' - 8"
D.2
FF TO MATCH EXST:98' - 8"
AE452
116
M
B
2 AE22
C3
B1
1 AE22
117C
AE401
A132
FE
2
C3
/8" 5'-1 5
6" 10' -
FF TO MATCH EXST:98' - 8"
2
FAM RR
0" 18' -
RN
A1
" 9' - 6
117
" 9' - 5
102
C1 104
120
2
E5
" 8' - 4
AE453
156B
F
CORRIDOR
" 8' - 0
10" 25' -
LEVEL 1 FF: 100'-0"
5 AE22
" 7' - 0 " 2' - 1
" 8' - 4
LOPE 1/12 S : P U RAMP
" 3' - 4
0" 4' - 1
ELEV 0" 18' -
" 2' - 8
A1
117A
" 2' - 8
RQ
07 9500.02
3
FF TO MATCH EXST:98' - 8"
2
20
B1
4" 14' -
CORRIDOR
STUDENT COMMONS
" 7' - 2
" 4' - 9
JANITOR
RR
AE452
2 6"
" 4' - 0
B2
9A
117A
8
" 3' - 2
4" 39' -
0" 33' -
BOYS
120
AE301
A2
119
RT
C
1
15
GIRLS
CORRIDOR
156
10 9600.02 18"
3 2
14
123B
121
MB-4
2
TRACK
KILN
123A
123
" 3' - 4
RV
TB-1
1
AE401
TB-1
7' - 9"
TB-2
1
200 Longhorn Street Vega, TX 79092
2
1
VEGA ISD HIGH SCHOOL
3.1
AF403
A133.2
100
1' - 11"
3
11' - 5"
B2
2
2A
2"
16
6' - 3"
18"
124
PROJECT
ELEC 123B
11"
6"
2
123A
124A
21 125 121B
AE301
9
TW-1
124B
VEST
128A
KB D2
128
G
SHEET NO.
AE101B 6
1
2
3
4
5
6
GENERAL SHEET NOTES A.
1.9
2
3
4
5
5.1
B. C. D. E. F. G.
1.9
2
C5
C5
3
4
AE202
5
H. I.
AE202
5.1
J.
E
2' - 3" 2' - 3" 6' - 8"
31' - 6"
K. 31' - 6"
BID LOT #4, RE: D2/AE101C
L.
ALL PLAN DIMENSIONS ARE TO FACE OF STUD, FACE OF CMU, OR CENTER OF COLUMN UNLESS NOTED OTHERWISE. REFER TO EXTERIOR ELEVATIONS FOR LOCATIONS, TYPE AND FINISH OF ALL EXTERIOR WALLS. ABUSE RESISTANT GYPSUM BOARD TO BE INSTALLED ON ALL HALLWAY, LOBBY, VESTIBULE, AND STORAGE ROOM WALLS UNLESS NOTED OTHERWISE. REFERENCE FINISH FLOOR ELEVATION = 100'-0" (MSLE). REF: CIVIL DRAWINGS FOR MSLE. REFER TO INTERIOR ELEVATIONS FOR INSTRUCTION SURFACE MOUNTING HEIGHTS. ALIGN NEW FINISHES WITH EXISTING WHERE APPLICABLE, TAPE AND TEXTURE. ALL GYPSUM BOARD CORNERS TO RECEIVE FULL HEIGHT CORNER GYPSUM BOARD CORNER GUARDS. ALL GYPSUM CEILING CORNERS TO RECEIVE FULL LENGTH CORNER GUARDS. FINAL LOCATION OF PAPER TOWEL DISPENSER TO BE COORDINATED WITH ARCHITECT. MASONRY JOINT LOCATIONS: EQUALLY SPACED ON MASONRY DIMENSIONS, WITH SPANS NOT TO EXCEED 20'-0" O.C. COORDINATE WITH ARCHITECT PRIOR TO FABRICATION. COORDINATE LOCATION WITH TILE JOINTS. ALL EXPOSED INTERIOR CMU WALLS TO BE PAINTED. COLOR TO BE SELECTED BY ARCHITECT. REFER TO INTERIOR FINISH SHEETS. GYPSUM CONTROL JOINT LOCATIONS: SPANS NOT TO EXCEED 20'-0" O.C. COORDINATE LOCATIONS WITH ARCHITECT PRIOR TO FABRICATION / INSTALLATION. COORDINATE LOCATIONS WITH TILE JOINTS. BASKETBALL COURT STRIPING IS SHOWN FOR REFERENCE ONLY. REFER TO INTERIOR FINISH SHEETS.
A5 AE302 2' - 3" 2' - 3" 31' - 6"
2
14
STOR
Y.9
149
2
AE221
2
2
2
2
2
149A
TB-1
TB-1
E5
147A
NORTH
146
S
S A
R EG I
C H ARL E
146A
1
2 1
CLASSROOM
152
146
D
MB-1
147
E3 AE302
D
08 1163.02
07 9500.02
14
D 14
1
14
08 1163.02
14
MB-1
MB-1
W
144
145
07 9500.01
GIRLS
144
V
D5
139
AE401
137A
150
137A
6' - 4"
U TB-1
A3
TB-1
2
AF404
8' - 0"
SPEC ED
TB-1
2
2
LEGEND STOR
2
D4
136A
2
136
1
1 10' - 5"
22
142
B2
2
137
4' - 5"
VEST
13
141
137
1
138
142B
142A
AE221
15' - 0"
150
AE302
IDF
7' - 7"
STOR
7' - 6"
ELEC
7' - 7"
4' - 4"
E5
9' - 2"
CORRIDOR 141
AE501
2
B4
CLASSROOM
2
138
MB-1
A
B1
PARTITION ASSEMBLY TYPE
1i XX
BUILDING SECTION / WALL SECTION
XX XX-XXX
LAB
AF403
XX EXTERIOR ELEVATIONS 19' - 3"
135 MB-1 MB-1 48' - 0"
8' - 0"
S
XX-XXX
10 12' - 0"
9' - 1"
FE
T
XX
136
CORRIDOR
10
WINDOW TYPE
AE202
8' - 0"
C
JAN
6' - 8"
143
143
139
15' - 4"
STAFF RR
12' - 10"
145
AE401
136A
B5
AE202
07 9500.02
BOYS
5' - 10"
E5
2"
2"
W.1
D
CORRIDOR 1
28' - 10"
W.2
CLASSROOM
3' - 4"
16'
3' - 4"
8'
6' - 8"
4'
STOR 2
1 2' - 8"
0'
2
147
PROJECT
2
FE
2
LEVEL 1 FLOOR PLAN - BID LOT #4 1/8" = 1'-0"
1
AE501
TB-1
2
2
147A
X
STOR 148A
TB-1
STOR
D2
2
A
X
2
INTERIOR ELEVATIONS
X
XX-XXX
MB-2
2
133B
134
10 1
TB-3
2
2
131
2
KEY PLAN - NTS 2
9' - 7"
CLASSROOM 132
10 D1 10"
39' - 4"
AE221
2
E1 MB-1
8' - 0"
131
ADDENDUM 004 - 02.15.2016
132
1
2
LAB
REVISIONS
132A
2
1 A
100% BID DOCUMENTS
STOR
10"
M
0.5
EXISTING TO REMAIN
134A
11' - 2"
8' - 0"
T
10
L
STOR
TB-1
8
7' - 6"
10A
TW-1
EXISTING TO REMAIN
TB-1 MB-2
FORBO TACKWALL, REFER TO INTERIORS
27' - 4"
133
MB-2
MB-1, MB-2, ETC.
1
7' - 6"
N
MARKERBOARD, REFER TO INTERIORS
134
8
133A
154
STOR/PREP
TB-1, TB-2, ETC.
132A
MECH
CLASSROOM TB-3
10' - 6"
28' - 4"
2A
TACKBOARD, REFER TO INTERIORS
2
2
TB-4
154
A
134A
10
MB-2
Q
7' - 10"
T
10
10
135
8' - 0"
D5 AE302
P
MB-1
R
X
X
1
B
200 Longhorn Street Vega, TX 79092
148
X
148
VEGA ISD HIGH SCHOOL
149
TE
ARCHITECT
2' - 8"
CLASSROOM
OF
3' - 4"
CLASSROOM
2
7' - 6"
D
18563
F1
3' - 4"
1
D
21' - 2"
TE
28' - 8"
149A
Y
2
28' - 8"
D
C1
AF404
Z 1
2' - 11"
9' - 10"
C
A150A
TB-1
14
ST
153A MB-1 2' - 11"
21' - 2"
B1 TB-1
6' - 0"
153B
6' - 0" 3' - 4"
D
6' - 8"
2
148
A
INTERIOR ARCHITECTURAL JOINT SYSTEM (EJ-01) EXTERIOR ARCHITECTURAL JOINT SYSTEM (EJ-2) STORM SHUTTER DOOR
2' - 8"
STOR
07 9500.01 07 9500.02 08 1163.02
T
148A
2
A151A
149
AE202
D
CLASSROOM MB-1
AD150
CLASSROOM
REFERENCE KEYNOTES
AR
R BAR E T
146A
2
2
D
7' - 6"
AD151
STOR
2
2
14' - 0"
2
153
3' - 4"
MB-1
MB-1
2 2
2' - 8"
B5 AD150A
AD151A
14' - 0"
21' - 2"
08 1163.02
VEST
ED
Y L OR
2' - 11"
MB-1
T
9' - 10"
MB-1
08 1163.02
S
C1
2' - 11"
D
Y.9
22
ER
EC T
D
A150
AE302
Z
TA
A151
AE322
IT
CLASSROOM
3' - 4" 2' - 8" 3' - 4"
D
CLASSROOM
21' - 2"
AE202
14
H
3' - 4" 2' - 8" 3' - 4"
14
31' - 6"
A5
A2
A153 D
6' - 8"
3' - 4"
VEST
A2 AE322
MB-2
3' - 4"
MB-2
152
MB-2
6' - 8"
6' - 8"
MB-2
A 31' - 6"
AREA C
DRAWN BY
KLS
REVIEWED BY
CBT
DATE
01.21.2016
10 PROJECT NO:
J
1
MB-1
TB-1
1A
MB-1
MATCH LINE
14-0424.002
DRAWING NAME
LEVEL 1 FLOOR PLAN - AREA C
2A 129B
13
10' - 8"
MB-1
125B
FE
A
MATCHLINE
FE
MATCHLINE A5 / AE101B
130
2
AREA B
NORTH
NORTH
A5 1
2
3
4
LEVEL 1 FLOOR PLAN - AREA C 1/8" = 1'-0"
0'
5
4'
8'
16'
INE CH L MAT
2/11/2016 11:26:18 AM
AREA A
SHEET NO.
AE101C 6
1
2
3
4
5
6
GENERAL SHEET NOTES 2
3
4
5
5.1
A. B.
BID LOT #4, RE: E1/AE141
23 0000.01 117' - 4" 17' - 6"
E
C4
C4
C4
AE542
AE542
AE542
Z
Z
Y.9
Y.9
C4
C4
AE542
AE542
8' - 6"
Y
ROOF PLAN - AREA C BID LOT #4
E1
40' - 2"
1/16" = 1'-0"
0'
12 '
24 '
36 '
W.1
D
W
07 7200.01 117' - 4"
V
A4 AE542
U 1
D
T
A
T
AE542
Y L OR
B1
C
EC T
W.2
T
TA
117' - 4"
AR
R BAR E T
IT
117' - 4"
ED
H
X
ER
S
ROOF SLOPE SHALL BE 3/8" PER FOOT MINIMUM UNLESS OTHERWISE NOTED. MAINTAIN MINIMUM VERTICAL FOR ROOFING MEMBRANE AT ALL FLASHING, PER MANUFACTURERS RECOMMENDATIONS. C. PROVIDE ROOF PROTECTION PADS AS SPECIFIED. INSTALL PER ROOF SYSTEMS MANUFACTURER'S RECOMMENDATIONS AT SERVICE SIDE OF MECHANICAL UNITS AND 4'-0" X 4'-0" AT ROOF HATCH. D. WHERE EXPOSED GAS LINES OR OTHER PIPES AND CONDUITS CROSS ROOF USE PREMANUFACTURED ROLLER LOW PROFILE PIPE SUPPORTS PER CODE REQUIREMENTS. E. ALL EXPOSED GAS PIPING ON ROOF TO BE PAINTED SAFETY YELLOW F. ALL ROOF TOP PENETRATIONS MUST BE A MINIMUM OF 8" ABOVE FINISHED ROOF SYSTEM INCLUDING ROOF HATCH. PENETRATIONS TO HAVE A MINIMUM OF 18" RADIUS CLEAR SPACE. G. ALL MECHANICAL EQUIPMENT CURBING MUST ALLOW FOR 18" CLEARANCE ABOVE FINISHED ROOF SYSTEM. H. WATER TEST CRICKETS TO INSURE POSITIVE DRAINAGE. ANY ROOFTOP EQUIPMENT 1.5 FEET WIDE OR GREATER SHALL HAVE CRICKET INSTALLED ON HIGH SIDE OF UNIT. I. WHERE EXPOSED GAS LINES OR OTHER PIPES AND CONDUITS CROSS ROOF USE PREMANUFACTURED ROLLER LOW PROFILE PIPE SUPPORTS PER CODE REQUIREMENTS. J. FOR TYPICAL ROOF PENETRATION DETAILS REFER TO ROOF DETAILS (TYP.). K. FOR ADDITIONAL ROOF PENETRATION DETAILS REFER TO M.E.P. DRAWINGS, (TYP.). L. ALL EXPOSED METAL FLASHING/TRIM PIECES ARE TO BE 24 GA. PRE-FINISHED GALVANIZED STEEL (U.N.O.) PAINT ALL EXPOSED METAL FLASHING/TRIM PIECES THAT ARE NOT PRE-FINISHED, AS WELL AS ALL EXPOSED MISCELLANEOUS PIECES (TYP.) GALVANIZE ALL METAL FLASHING/TRIM PIECES THAT ARE NOT SEEN. M. ALL TAPERED INSULATION CRICKETS OVER METAL ROOF DECK (3/4"/FT. MIN. SLOPE) AS WELL AS, AT HIGH SIDE OF ALL MECHANICAL UNITS, SKYLIGHTS, ROOF HATCHES, & MISCELLANEOUS ROOF PENETRATIONS, TO SHED WATER AROUND, AND TO INSURE POSITIVE ROOF DRAINAGE (TYP.). N. ALL WOOD BLOCKING AT ROOF EDGES, RIDGES, ETC. TO BE FABRICATED FROM CONT. MIN. 2X6'S FRWD BLOCKING. PROVIDE BIGGER 2X FR-WD AS REQUIRED, PER DETAIL DIMENSIONS (TYP.). O. REFER TO M.E.P. & STRUCTURAL DRAWINGS FOR LOCATIONS OF ROOFTOP MECHANICAL EQUIPMENT AND ADDITIONAL INFO, (TYP.). P. ALL GUTTERS (IF REQUIRED OR SHOWN) TO BE PRE-FINISHED 24 GA. GALVANIZED STEEL (GUTTER SIZES PER ROOF LEGEND) (TYP. U.N.O.) PROVIDE PAINTED 1/4" X 1 1/2" GALVANIZED STEEL BENT PLATE BRACKETS AND 14 GA. X 1" GALVANIZED STEEL SPACERS AT 36" O.C. MAX., STAGGER W/ EACH OTHER AT 18" O.C. (TYP.) PROVIDE PREFINISHED GUTTER E.J.'S PER SMACNA, FIGURE 1-7, (TYP.) PROVIDE 1/4" HARDWARE CLOTH SCREENS AT ALL GUTTERS PER SMACNA, FIGURE 1-24, FIG. B (TYP.) LOCATE GUTTER E.J.'S PER ROOF PLAN, (30' MAX. SPAN) (TYP.). Q. ALL EXTERNAL DOWNSPOUTS TO BE PRE-FINISHED 24 GA. GALVANIZED STEEL PER SMACNA, FIGURE 1-32, FIG. B, (TYP.) DOWNSPOUTS ARE 4"X6". (TYP. U.N.O.) LOCATE INDICATED PER ROOF PLAN, (TYP.) PROVIDE PAINTED 15 GA.X2" GALVANIZED STEEL HANGERS AT 48" O.C., MAX. PER SMACNA FIGURE I35, FIG. B, (TYP.) PROVIDE PAINTED VANDALPROOF STRAINERS AT EACH DOWNSPOUT, (TYP.) . R. INSURE ROOF DRAINS, RINGS, CLAMPS, AND LEAD ROOF DRAIN FLASHINGS ARE USED. S. PROVIDE STEP FLASHING AT SLOPED ROOF HI/LO CONDITIONS. T. VERIFY ELEVATION OF ROOF DRAIN RELATIVE TO OVERFLOW SCUPPER PRIOR TO INSTALLATION OF SCUPPERS, REFER TO ROOF DETAILS. U. FURNISH AND INSTALL 16 GA. SHEET METAL VANDAL GUARDS ON ALL METAL LINES/PIPING TO THE ROOF. VANDAL GUARDS SHALL BE PAINTED, AS DIRECTED BY ARCHITECT. V. FURNISH TWO YEAR WARRANTY FROM BOTH ROOFING COMPANY AND MANUFACTURE. PROVIDE ROOFING COMPANY'S WRITTEN ROOFING AND FLASHING INSPECTION AND SERVICE GUARANTEE AGAINST FAULTY WORKMANSHIP AND DEFECTIVE MATERIAL FOR TWO YEARS. REQUIRE A SEPARATE WARRANTY IN SHEET METAL SECTION OF SPECIFICATIONS. W. U.N.O. PAINT EXPOSED METAL FLASHING/TRIM PIECES THAT ARE NOT PRE-FINISHED, AS WELL AS ALL EXPOSED MISCELLANEOUS STEEL PIECES. X. PROVIDE ALL MISCELLANEOUS STEEL FRAMING MEMBERS/PIECES, REQUIRED FOR FRAMING OPENINGS IN ROOF, WALLS, FLOORS, ETC. WHERE MEMBERS (SUCH AS LINTELS) ARE EXPOSED, THEN THEY ARE TO BE PAINTED, AS DIRECTED BY ARCHITECT.
TE
S
1.9
5.1
18563
OF
A
5
AE542
S
4
ST
3
R EG I
2
C H ARL E
1.9
C4
TE
X
ARCHITECT
A4 AE542 PROJECT
S
REFERENCE KEYNOTES
A4
REPAIR ROOF AT LOCATION OF ROOF PENETRATION. PARAPET LADDER COLLECTOR BOX WITH OVERFLOW AND 6" X 6" DOWNSPOUT INSTALL NEW DOWNSPOUT TO SERVE EXISTING COLLECTOR BOX. DRAIN ONTO NEW ROOF ADJACENT ROOF HATCH
AE542
07 7200.01
P N M 0.5
L MATCHLINE
AREA C AREA B
10
7
11
12
A4
J
AE542
117' - 4"
A4 AE542
C
H G.9
A4
SIM
AE542
MATCHLINE
AREA B 1' - 8"
AREA A
G 07 6200.03
SIM
TYP
B4
R1.8
R2.1
R2
E4
TYP.
11' - 8"
3.1
AE542
07 6200.06
D1
F
AE542
RT
07 6200.03
AE541
LEGEND
E
05 5000.08
D.2
124' - 0"
APPROXIMATE LOCATION OF ROOF OPENING - REPAIR AND ENCLOSE PER MANUFACTURER REQUIREMENTS
1" 15' -
3' - 1"
07 7200.01
RR
B
TYP
B4
R1.8 R2
EXISTING TO REMAIN
AE542
LOW
/ 3/8"
AE542
RQ
AE542
RK
HIGH TYP B4
117' - 4"
B3
RN
1'-0"
C2
" 2' - 4
LOW B3
RJ
AE542
LOW
RG
/ 3/8"
B2 121' - 4"
1'-0"
RM RM
11"
A2
HIGH
BID LOT #3, RE: A1/AE141
REVISIONS
0" 6' - 1
" 6' - 8
B
A1
AE542
A3
07 6200.06
AE542
AE542 A2
RE
AE542
KEY PLAN - NTS
A
118' - 8"
AE542 D5
07 6200.06
AE542
RB
07 6200.03
PROPOSED NEW
RD
C2
100% BID DOCUMENTS
C
02 4119.24
AE542
AE542
6' - 8"
HIGH TYP
AE542
C2
EXISTING TO REMAIN
D
AE542
10" 20' -
B4
R1
02 4119.24 D1
RV
200 Longhorn Street Vega, TX 79092
Q
02 4119.24 05 5000.08 07 6200.03 07 6200.06
VEGA ISD HIGH SCHOOL
R
R8.2
AE542
8 8.8 9
13 14 15
EXST TO REMAIN
16
DRAWN BY
D5
AREA C
AE542
EXISTING
NK
REVIEWED BY DATE PROJECT NO:
A 07 6200.03 B4
TYP
AE542
12 '
24 '
R8.1
R9
ROOF PLAN AREA B AREA A
NORTH
A5
36 '
2
3
14-0424.002
DRAWING NAME
4
NORTH
ROOF PLAN 1/16" = 1'-0"
0'
5
8'
16'
32'
INE CH L MAT
1
ROOF PLAN - AREA A BID LOT #3 0'
R2.9
R6
R7 R8
MATCH LINE
R3 B AREA
RA
R5
A AREA
2/11/2016 11:14:13 AM
07 6200.03
1/16" = 1'-0"
01.21.2016
114' - 0"
RF
A1
CBT
SHEET NO.
AE141 6
1
2
3
4
5
6 DIMENSIONAL CAST METAL LETTERS AT MAIN ENTRY
EXISTING MASONRY WALL TO REMAIN VERIFY CONDITONS IN FIELD
5/8" ROOF PARAPET SHEATHING
WRAP BUR SYSTEM UNDER COPING
ANCHOR FLASHING AND FILL WITH SEALANT
CANT STRIP FIRE RETARDANT TREATED WOOD BLOCKING
T.O.P. RE: ELEV.
METAL FLASHING
1/2" COVER BOARD
COMPRESSIBLE INSULATION 12" MIN.
1/2" DENSDECK
1/2" DENSDECK WRAP BUR SYSTEM UNDER COPING
METAL COMPOSITE WALL PANELS
CANT STRIP 1/2" COVER BOARD
8" MIN.
FIRE RETARDANT TREATED WOOD BLOCKING
ROOF ARCHITECTURAL JOINT SYSTEM (EJ-4)
E
MANUFACTURED COPING
WRAP BUR SYSTEM UNDER COPING
D4
ROOF INSULATION
AE542
1/2" DENSDECK
FIRE RETARDANT TREATED WOOD BLOCKING PRE-FINISHED METAL COPING CONTINUOUS WEATHERPROOF MEMBRANE ON TOP OF WALL TURNED DOWN BOTH SIDES
T.O.P. RE: ELEV.
STEEL ROOF DECK ADJUSTABLE MASONRY VENEER ANCHOR
REFER TO STRUCTURAL
METAL COMPOSITE SOFFIT PANELS ADJUSTABLE MASONRY VENEER ANCHOR
AR T
C
S
R BAR E T
C H ARL E
Y L OR
EC T
TA
R EG I
ED
IT
METAL FLASHING
ER
H
ST
2"
WRAP BUR SYSTEM UNDER COPING
ADJUSTABLE MASONRY VENEER ANCHOR
WRAP BUR SYSTEM UNDER COPING
T.O.P. RE: ELEV.
ADJUSTABLE MASONRY VENEER ANCHOR
0"
6"
12 "
D4
1" AIR SPACE
1/2" COVER BOARD 1/2" DENSDECK
COPING DETAIL 3" = 1'-0"
0"
ADJUSTABLE MASONRY VENEER ANCHOR
3"
6"
D5
9"
TE
18563
OF
A
BRICK MASONRY VENEER SYSTEM
WRAP BUR SYSTEM UNDER COPING
18 "
A
T
1 1/2" = 1'-0"
S
D1
ROOF EXPANSION JOINT DETAIL
S
RE: RCP
CANT STRIP
TE
X
PARAPET DETAIL 1 1/2" = 1'-0"
0"
6"
12 "
18 " ARCHITECT
ROOF INSULATION 1 1/2" CONTINUOUS RIGID INSULATION CONTINUOUS WEATHERPROOF MEMBRANE ON TOP OF WALL TURNED DOWN BOTH SIDES
CANT STRIP
C2
1 1/2" = 1'-0"
0"
6"
BRICK MASONRY VENEER SYSTEM 2 7/8" AIR SPACE
1/2" COVER BOARD 1/2" DENSDECK
12 "
18 "
WRAP BUR SYSTEM UNDER COPING
WEATHER BARRIER BRICK MASONRY VENEER SYSTEM
ADJUSTABLE MASONRY VENEER ANCHOR
ROOF INSULATION
1 1/2" CONTINUOUS RIGID INSULATION
1/2" DENSDECK CONCRETE OVER METAL DECK
A3
T.O.P. RE: ELEV. PROJECT
WRAP BUR SYSTEM UNDER COPING
PARAPET DETAIL AT 8" CMU & BRICK VENEER
SHEET WASHER FASTENERS
T.O.P. RE: ELEV.
WEEP HOLES AS REQUIRED
WEATHER BARRIER
AE542 INSIDE CLOSURE WITH TAPE SEALANT TOP AND BOTTOM
PRE-FINISHED METAL COPING
CORRUGATED METAL WALL PANEL WITH EXPOSED FASTENERS
T.O.P. RE: ROOF
FIRE RETARDANT TREATED WOOD NAILER
C4
INSIDE CLOSURE WITH TAPE SEALANT TOP AND BOTTOM
CANT STRIP WRAP BUR SYSTEM UNDER COPING 1/2" COVER BOARD
1/2" COVER BOARD 1/2" DENSDECK
CONCRETE UNIT MASONRY SYSTEM
5/8" WALL SHEATHING WEATHER BARRIER
CANT STRIP ROOF INSULATION
WRAP BUR SYSTEM UNDER COPING 1/2" COVER BOARD 1/2" DENSDECK
CONCRETE OVER METAL DECK
BRICK MASONRY VENEER SYSTEM 1" AIR SPACE 1 1/2" CONTINUOUS RIGID INSULATION
WEEP/VENT 1" AIR SPACE
1/2" DENSDECK
1 1/2" CONTINUOUS RIGID INSULATION STEEL EDGE ANGLE
STEEL EDGE ANGLE
METAL FLASHING
BACKER ROD AND SEALANT METAL TERMINATION BAR WEATHER BARRIER CANT STRIP
METAL FLASHING
FIRE RETARDANT TREATED WOOD BLOCKING 12" MIN
STEEL ROOF DECK
2"
1/2" DENSDECK COMPRESSIBLE INSULATION
CANT STRIP
12 "
18 "
CANT STRIP
1/2" DENSDECK
WRAP BUR SYSTEM UNDER COPING 1/2" COVER BOARD 1/2" DENSDECK
ROOF INSULATION
AE542
SHEET WASHER FASTENERS
T.O.P. RE: ELEV.
3" = 1'-0"
0"
3"
6"
9"
PRE-FINISHED METAL COPING
FIRE RETARDANT TREATED WOOD BLOCKING
T.O.P. RE: ELEV.
BRICK MASONRY VENEER SYSTEM WRAP BUR SYSTEM UNDER COPING
1" AIR SPACE
1/2" DENSDECK
WEATHER BARRIER BRICK MASONRY VENEER SYSTEM
ADJUSTABLE MASONRY VENEER ANCHOR
ROOF INSULATION
1 1/2" CONTINUOUS RIGID INSULATION
1/2" DENSDECK
WEEP HOLES AS REQUIRED
WEATHER BARRIER
STEEL ROOF DECK
1/2" DENSDECK
COPING DETAIL AT SHELTER
CONTINUOUS WEATHERPROOF MEMBRANE ON TOP OF WALL TURNED DOWN BOTH SIDES
B5
1/2" COVER BOARD
1/2" COVER BOARD
STEEL BEAM (REFER TO STRUCTURAL)
6"
WRAP BUR SYSTEM UNDER COPING
WRAP BUR SYSTEM UNDER COPING
METAL TERMINATION BAR
12" MIN.
STEEL ROOF DECK
0"
C5
ADJUSTABLE MASONRY VENEER ANCHOR WEEP HOLES AS REQUIRED
BRICK MASONRY VENEER SYSTEM
METAL FLASHING
PARAPET DETAIL AT SHELTER 1 1/2" = 1'-0"
6"
5/8" ROOF PARAPET SHEATHING
4" TYP
C
WEEP/VENT
ROOF ARCHITECTURAL JOINT SYSTEM (EJ-4)
CANT STRIP
1 1/2" CONTINUOUS RIGID INSULATION
STEEL BEAM
WEATHER BARRIER
CLOSED CELL MASONRY UNIT
WRAP BUR SYSTEM UNDER COPING
BRICK MASONRY VENEER SYSTEM
8" MIN FLASHING HGT
WRAP BUR SYSTEM UNDER COPING
ADJUSTABLE MASONRY VENEER ANCHOR
T.O.P. RE: ELEV.
200 Longhorn Street Vega, TX 79092
D
C5 AE542
VEGA ISD HIGH SCHOOL
STEEL EDGE ANGLE
8" MIN FLASHING HGT
STEEL ROOF DECK
PRE-FINISHED METAL COPING
FIRE RETARDANT TREATED WOOD BLOCKING
6"
WEATHER BARRIER
4" TYP
1/2" DENSDECK
ADJUSTABLE MASONRY VENEER ANCHOR
STEEL EDGE ANGLE
STEEL ROOF DECK 1 1/2" CONTINUOUS RIGID INSULATION 1/2" DENSDECK
B1
ROOF EXPANSION JOINT DETAIL 1 1/2" = 1'-0"
0"
6"
12 "
PARAPET DETAIL
B2
18 "
1 1/2" = 1'-0"
0"
6"
12 "
B
B3
18 "
ROOF DETAIL - WALL TO ROOF 1 1/2" = 1'-0"
0"
6"
12 "
B4
18 "
PARAPET DETAIL AT CMU & BRICK VENEER 1 1/2" = 1'-0"
0"
6"
12 "
B5
18 "
COPING DETAIL AT CMU & BRICK VENEER 3" = 1'-0"
0"
3"
6"
9"
A3 AE542
INSIDE CLOSURE WITH TAPE SEALANT TOP AND BOTTOM
ROOF ARCHITECTURAL JOINT SYSTEM (EJ-4)
1
PRE-FINISHED METAL COPING FIRE RETARDANT TREATED WOOD BLOCKING
INSIDE CLOSURE WITH TAPE SEALANT TOP AND BOTTOM METAL FLASHING
BRICK MASONRY VENEER SYSTEM
4" TYP.
CANT STRIP 1/2" COVER BOARD WRAP BUR SYSTEM UNDER COPING
REVISIONS
INSIDE CLOSURE WITH TAPE SEALANT TOP AND BOTTOM
COMPRESSIBLE INSULATION
BATT INSULATION
COPING BEYOND CONTINUOUS WEATHERPROOF MEMBRANE ON TOP OF WALL TURNED DOWN BOTH SIDES
5/8" ROOF PARAPET SHEATHING
METAL FLASHING
T.O.P. RE: ELEV. 113' - 4 1/2" VERIFY
WEEP/VENT 1" AIR SPACE CANT STRIP WRAP BUR SYSTEM UNDER COPING 1/2" COVER BOARD
ROOF INSULATION BATT INSULATION 6"
3 5/8"
WEATHER BARRIER 1 1/2" CONTINUOUS RIGID INSULATION CORRUGATED METAL WALL PANEL WITH EXPOSED FASTENERS
1/2" DENSDECK
2"
A
STEEL ROOF DECK
BRICK MASONRY VENEER SYSTEM WEEP/VENT ADJUSTABLE MASONRY VENEER ANCHOR
5/8" ROOF PARAPET SHEATHING
ROOF INSULATION
STEEL BEAM (SEE STRUCTURAL)
2/15/2016 11:48:51 AM
A5 AE542
SHEET WASHER FASTENERS
CANT STRIP WRAP BUR SYSTEM UNDER COPING
BRICK MASONRY VENEER SYSTEM
FIRE RETARDANT TREATED WOOD BLOCKING
DRAWN BY REVIEWED BY DATE
ADJUSTABLE MASONRY VENEER ANCHOR
BRICK MASONRY VENEER SYSTEM
5/8" ROOF PARAPET SHEATHING
1 1/2" CONTINUOUS RIGID INSULATION
A1
INTERIOR ARCHITECTURAL JOINT SYSTEM (EJ-01)
ROOF EXPANSION JOINT DETAIL 1 1/2" = 1'-0"
0"
1
6"
12 "
18 "
01.21.2016
PROJECT NO:
14-0424.002
ROOF DETAILS
ADJUSTABLE MASONRY VENEER ANCHOR 1 1/2" CONTINUOUS RIGID INSULATION
STEEL EDGE ANGLE
RE: RCP
GYPSUM BOARD
BT/AL
DRAWING NAME
WEEP HOLES AS REQUIRED
WEATHER BARRIER
1/2" DENSDECK
AM
WEATHER BARRIER
STEEL ROOF DECK 111' - 2" BOTTOM OF DECK
WEATHER BARRIER
T.O.P. RE: ELEV.
WRAP BUR SYSTEM UNDER COPING
1 1/4" AIR SPACE
1/2" COVER BOARD
Date 1 Revision ADDENDUM 004 -1 02.15.2016
PRE-FINISHED METAL COPING
5/8" WALL SHEATHING
METAL STUD, 3-5/8" RE: RCP
CONTINUOUS WEATHERPROOF MEMBRANE ON TOP OF WALL TURNED DOWN BOTH SIDES
1 1/2" CONTINUOUS RIGID INSULATION
WEATHER BARRIER
CLIP
2'1'- -210" 1/2"
METAL TERMINATION BAR 12" MIN.
1/2" DENSDECK
100% BID DOCUMENTS
WEEP/VENT
WEATHER BARRIER
METAL TERMINATION BAR
12" MIN.
BRICK MASONRY VENEER SYSTEM
CORRUGATED METAL WALL PANEL WITH EXPOSED FASTENERS
6"
CORRUGATED METAL WALL PANEL WITH EXPOSED FASTENERS
4" TYP.
WEATHER BARRIER
METAL STUD
T.O.P. RE: ELEV.
INSIDE CLOSURE WITH TAPE SEALANT TOP AND BOTTOM
8" MIN FLASHING HGT
5/8" ROOF PARAPET SHEATHING
5/8" WALL SHEATHING STEEL ROOF DECK STEEL EDGE ANGLE
A2
PARAPET DETAIL 1 1/2" = 1'-0"
0"
2
6"
12 "
A3
18 "
3
COPING DETAIL 3" = 1'-0"
0"
3"
6"
A4
9"
4
PARAPET DETAIL AT STUD & BRICK VENEER 1 1/2" = 1'-0"
0"
6"
12 "
A5
18 "
5
SHEET NO.
COPING DETAIL AT STUD & BRICK VENEER 3" = 1'-0"
0"
3"
6"
9"
6
AE542
1
2
3
4
5
6
GENERAL SHEET NOTES 3
4
5 5.1 A. B. C.
D. E. RG-01
VEST
16 RG-02
A153
SD-01 375
SD-01 375
SD-02 200
CLASSROOM A150
16"x16"
21
18"x18"
SD-01 375
8"x6" 18"x18"
STOR A151 A151A
Z
SD-02 100
1.9
2
3
4
5 5.1
RG-02
STOR
TO RTU-01B
20
A150A
CORRIDOR
Z
A152
Y.9
1
CLASSROOM 149
CLASSROOM 148
Y.9
40"x16"
RG-01
RG-01
20"x20"
16
LV-5
SD-01 325
SD-01 325
15
RG-01
RG-02
12"x8"
M
SCALE: 1/8" = 1'-0"
0'
4'
8'
STOR 149A
16'
8"x6"
CLASSROOM 149 RG-02
STOR 147A
3 $ $
RG-02
$ $
18"x18"
SD-01 375 SD-01 375
X
8"x6"
TO RTU-05
RG-01
TO RTU-04
SD-01 375
40"x16"
CLASSROOM 146
4
10"x14"
10"x14"
18"x18" M
SD-01 375
LV-8
W.2
CLASSROOM 147
40"x16"
LV-10
RG-01
40"x16"
18"x18"
10"x12"
12"x12" EG-02 140
SD-02 150
C
STOR 137A
FC-01
SD-02 90
SD-02 90
FC-02 1/2" RS 1/4" RL
RG-02
SD-01 150
12"x10"
8"x6"
TO RTU-07
8"x6"
SD-01 150
SD-01 375
7
RG-01 SD-01 400
SPEC ED 137
10"x10"
16"x16" 18"x18"
17
SD-01 375
102840 I C E N S E E SS G IO N A L E N
PROJECT
3
CLASSROOM 136
SD-01 375
16"x16"
T
SD-02 100 STOR 136A RG-02
A
Abbas 2016.02.15 13:22:30-07'00'
SD-01 375
10"x14"
10"x14"
22. 23. 24. 25.
RG-02
RG-01 SD-01 400
21.
SD-02 280
10"ø
TO RTU-06 1
17. 18. 19. 20.
VEST 142
TO RTU-08 SD-01 400
16.
BOYS 144
EG-02 400
SD-02 90
12"ø
18"x18"
IDF 141
8"x6"
U
EG-02 90
16"x12"
1
6
SD-02 150
JAN 139
16"x16"
STAFF RR 143
ELEC 150
CORRIDOR 138
14
RG-01
10"x12" 6"ø
10"x12" 6"ø
EG-02 370
SD-01 400
14. 15.
5
10"x12"
1/2" RS 1/4" RL
LV-9
SD-01 375
16"x16"
16
W.1
V
16
20"x20"
RG-01
W
6. 7. 8. 9. 10. 11. 12. 13.
15
SD-01 20"x20" 375
RG-01
GIRLS 145
40"x16"
M
LV-7
SD-01 375
5.
SD-01 375
16"x16"
15
4.
SD-02 100 STOR 146A RG-02
8"x6"
RG-02 SD-02 100
3.
E O F T EX
ABBAS SHIRIAN OF
LEVEL 1 HVAC PLAN - AREA C ALT
SD-02 100 STOR 148A
16"x16" TO RTU-03
TO RTU-02
2.
AT
L
SD-01 325
SD-02 100 8"x6"
40"x16"
SD-01 375
ARCHITECT
PR
D2
SD-01 375
PROVIDE DUCTLESS SPLIT COOLING UNIT. INSTALL UNIT LEVEL ON WALL FOR PROPER CONDENSATE DRAINAGE. COORDINATE INSTALLATION WITH ROOM EQUIPMENT. UNIT CONDENSATE LINE SIZED PER MANUFACTURER, PUMPED TO JANITORS SINK OR FLOOR SINK. REFER TO PLUMBING DRAWINGS FOR ADDITIONAL INFORMATION. PROVIDE LIQUID AND VAPOR PIPING. SIZE PIPING, TRAP AND SLOPE REFRIGERANT LINES PER MANUFACTURER'S INSTRUCTIONS. CONTRACTOR TO COORDINATE SHORTEST ROUTING TO ASSOCIATED REMOTE CONDENSING UNIT. PROVIDE ALL VALVES AND ACCESSORIES FOR A COMPLETE AND OPERATIONAL SYSTEM. REFER TO DETAILS AND EQUIPMENT SCHEDULE FOR ADDITIONAL INFORMATION. 16"X16" SUPPLY AND 18"X18" RETURN DUCT UP TO RTU-02 ON THE ROOF. NOTE ELBOW AND VERTICAL DUCTWORK UP TO UNIT SHALL BE 5/16" WELDED CARBON STEEL CONSTRUCTION. THIS ROOM IS PART OF THE STORM SHELTER AREA. THE INTENT IS TO PROVIDE HEAVY GAGE DUCTWORK AND ELBOW TO PREVENT HEAVY DEBRI FROM DIRECTLY ENTERING ROOM. PROVIDE ADDITIONAL BRACING TO SUPPORT DUCTWORK VERTICALLY. REFER TO STRUCTURAL DRAWINGS. 16"X16" SUPPLY AND 18"X18" RETURN DUCT UP TO RTU-03 ON THE ROOF. NOTE ELBOW AND VERTICAL DUCTWORK UP TO UNIT SHALL BE 5/16" WELDED CARBON STEEL CONSTRUCTION. THIS ROOM IS PART OF THE STORM SHELTER AREA. THE INTENT IS TO PROVIDE HEAVY GAGE DUCTWORK AND ELBOW TO PREVENT HEAVY DEBRI FROM DIRECTLY ENTERING ROOM.PROVIDE ADDITIONAL BRACING TO SUPPORT DUCTWORK VERTICALLY. REFER TO STRUCTURAL DRAWINGS. 16"X16" SUPPLY AND 18"X18" RETURN DUCT UP TO RTU-04 ON THE ROOF. NOTE ELBOW AND VERTICAL DUCTWORK UP TO UNIT SHALL BE 5/16" WELDED CARBON STEEL CONSTRUCTION. THIS ROOM IS PART OF THE STORM SHELTER AREA. THE INTENT IS TO PROVIDE HEAVY GAGE DUCTWORK AND ELBOW TO PREVENT HEAVY DEBRI FROM DIRECTLY ENTERING ROOM. PROVIDE ADDITIONAL BRACING TO SUPPORT DUCTWORK VERTICALLY. REFER TO STRUCTURAL DRAWINGS. 16"X16" SUPPLY AND 18"X18" RETURN DUCT UP TO RTU-05 ON THE ROOF. NOTE ELBOW AND VERTICAL DUCTWORK UP TO UNIT SHALL BE 5/16" WELDED CARBON STEEL CONSTRUCTION. THIS ROOM IS PART OF THE STORM SHELTER AREA. THE INTENT IS TO PROVIDE HEAVY GAGE DUCTWORK AND ELBOW TO PREVENT HEAVY DEBRI FROM DIRECTLY ENTERING ROOM. PROVIDE ADDITIONAL BRACING TO SUPPORT DUCTWORK VERTICALLY. REFER TO STRUCTURAL DRAWINGS. 16"X16" SUPPLY AND 18"X18" RETURN DUCT UP TO RTU-06 ON THE ROOF. 16"X16" SUPPLY AND 18"X18" RETURN DUCT UP TO RTU-07 ON THE ROOF. 16"X16" SUPPLY AND 18"X18" RETURN DUCT UP TO RTU-08 ON THE ROOF. 16"X16" SUPPLY AND 18"X18" RETURN DUCT UP TO RTU-09 ON THE ROOF. 16"X16" SUPPLY AND 18"X18" RETURN DUCT UP TO RTU-10 ON THE ROOF. 16"X16" SUPPLY AND 18"X18" RETURN DUCT UP TO RTU-11 ON THE ROOF. 16"X16" SUPPLY AND 18"X18" RETURN DUCT UP TO RTU-12 ON THE ROOF. INSTALL SMOKE DETECTOR AND SAMPLING TUBES FURNISHED BY DIVISION 28 IN DUCTWORK. POWER AND WIRING BY DIVISION 26 AND DIVISION 28. 12"X12" EXHAUST DUCT UP TO EF-01 ON THE ROOF. 40"X16" RATED STORM SHELTER VENTILATION LOUVER INSTALLED BELOW WINDOW OPENING. PROVIDE WALL SLEEVE AND MOTORIZED DAMPER INTERLOCKED TO OPEN WITH WALL SWITCH. POWER SHALL BE FROM EMERGENCY BATTERY POWER. 20"X20" (5/16" THICK) CARBON STEEL DUCT UP THROUGH ROOF. TERMINATE ABOVE ROOF WITH GOOSENECK OF SAME CONSTRUCTION. PROVIDE DUCT WITH MOTOIZED DAMPER TO OPEN WITH WALL SWITCH. POWER SHALL BE FROM EMERGENCY BATTERY POWER. 8" DIA STAINLESS STEEL EXHAUST HOOD FROM FUMEHOOD UP TO EXHAUST FAN EF-08 ON ROOF. 8" DIA STAINLESS STEEL EXHAUST HOOD FROM FUMEHOOD UP TO EXHAUST FAN EF-07 ON ROOF. COMBINATION FIRE / SMOKE DAMPER. 16"X16" SUPPLY AND 18"X18" RETURN DUCT UP TO RTU-01A ON THE ROOF. NOTE ELBOW AND VERTICAL DUCTWORK UP TO UNIT SHALL BE 5/16" WELDED CARBON STEEL CONSTRUCTION. THIS ROOM IS PART OF THE STORM SHELTER AREA. THE INTENT IS TO PROVIDE HEAVY GAGE DUCTWORK AND ELBOW TO PREVENT HEAVY DEBRI FROM DIRECTLY ENTERING ROOM. PROVIDE ADDITIONAL BRACING TO SUPPORT DUCTWORK VERTICALLY. REFER TO STRUCTURAL DRAWINGS. 16"X16" SUPPLY AND 18"X18" RETURN DUCT UP TO RTU-01B ON THE ROOF. NOTE ELBOW AND VERTICAL DUCTWORK UP TO UNIT SHALL BE 5/16" WELDED CARBON STEEL CONSTRUCTION. THIS ROOM IS PART OF THE STORM SHELTER AREA. THE INTENT IS TO PROVIDE HEAVY GAGE DUCTWORK AND ELBOW TO PREVENT HEAVY DEBRI FROM DIRECTLY ENTERING ROOM. PROVIDE ADDITIONAL BRACING TO SUPPORT DUCTWORK VERTICALLY. REFER TO STRUCTURAL DRAWINGS. 18"x18", 1" AL EXHAUST DUCT UP TO ROOF EXHAUST FAN EF-10. 18"X18", 1" AL EXHAUST DUCT UP TO ROOF EXHAUST FAN EF-11. EXTEND 4" COMBUSTION AIR DUCT FROM WATER HEATER UP THROUGH ROOF. EXTEND 4" TYPE B FLUE FROM WATER HEATER UP THROUGH ROOF.
S
18"x18"
LV-11
SD-01 325
Y
NORTH
1.
20"x20"
CLASSROOM 148 2
40"x16"
LV-12
15
LV-6
D
SD-01 375 M
16"x16"
10"x14"
SHEET KEYNOTES
SD-01 375
SD-02 200
40"x16"
RG-01
16
R
CLASSROOM
8"x6"
16"x16"
TO RTU-01A
0.5
SD-01 375
D
RG-02
SD-02 100
SD-01 325
EE
SD-01 325
16
16"x16"
10"x14"
15
10"x14"
15
IN
12"x8"
200 Longhorn Street Vega, TX 79092
SD-01 325
RG-01
VEGA ISD HIGH SCHOOL
SD-01 325
E
RG-01
10"x14"
RG-01
ALL RETURN AIR AND GENERAL EXHAUST DUCTWORK SHALL BE 1" ACOUSTICALLY LINED - TYPE D-3 AS SPECIFIED IN SPECIFICATION 230700. ALL SUPPLY DUCTWORK SHALL BE WRAPPED WITH 1.5" INSULATION-TYPE D-1 AS SPECIFIED IN SPECIFICATION 230700. ALL ROUND SUPPLY BRANCH DUCTS CONNECTED TO CEILING SUPPLY DIFFUSERS SHALL MATCH THE NECK DIAMETER OF THE INDICATED SUPPLY DIFFUSER. SEE GRILLES AND DIFFUSERS SCHEDULE ON SHEET M-702 FOR SUPPLY DIFFUSERS REQUIREMENTS. 22"X22" CEILING ACCESS DOORS SHALL BE PROVIDED AT ALL BALANCING DAMPERS, FIRE DAMPERS, FIRE/SMOKE DAMPERS AND SMOKE DETECTORS LOCATED ABOVE HARD CEILINGS. THERMOSTATS SHALL BE MOUNTED AT 48" A.F.F. PROVIDE METAL LOCKING COVERS FOR ALL THERMOSTATS LOCATED IN ALL UNSUPERVISED AREAS THAT ARE ACCESSIBLE TO STUDENTS. ADMIN SPACES, KITCHEN AND OFFICES ARE THE EXCEPTION.
ST
1.9 2
$ EG-01 1000
14"x14"
8
EG-01 1000
14"x14"
18"x18" SD-01 425
S
18"x18"
SD-01 425
22
13
RG-01
RG-01
RG-01
CLASSROOM 134 RG-01
SD-01 375
SD-01 375
RG-01 FSD
16"x16"
19 FSD
18"x18"
10"x10"
12"x14"
R
MECH 154
Q
12"x12"
LAB 135
SD-01 425
T
RG-02
UH-01
SD-01 425
3
P
19
FSD
SD-01 375
SD-01 150
$ EG-01 1000 14"x14"
T
25
SD-01 400
TO RTU-11
SD-02 100
TO RTU-12 8"x6"
CORRIDOR 138 SD-01 400 16"x16"
SD-01 375
FSD
11
L
10"x14"
23
19
LAB 131
RG-01
SD-01 400
FSD
18
SD-01 375
18"x18" SD-01 150
SD-01 400
1
01/29/16
ADDENDUM #01
2
02/05/16
ADDENDUM #02
3
02/15/16
ADDENDUM #04
8"x6"
TO RTU-10
RG-01
EG-01 14"x14" 1000
18"x18"
RG-02
16"x16"
RG-01
M
Addendum 004 REVISIONS
10
SD-02 300
18"x18"
N
SD-01 375
FSD
STOR/PREP 133
24
TO RTU-09
10"x14"
B
10"x14"
9
STOR 134A STOR 132A
KEY PLAN - NTS
SD-02 RG-02100
SD-01 375
DRAWN BY
SD-01 375
REVIEWED BY
CLASSROOM 132
12
J
DATE
16"x16"
18"x18"
RG-01
RG-01
02.15.2016
TO RTU-15
CLASSROOM 129
14-0424.002
DRAWING NAME
MATCH LINE
A3 / MH101B
RLM
AREA C PROJECT NO:
A
NZ
LEVEL 1 HVAC PLAN - AREA C
A3 / MH101B LIFESKILLS 130 AREA B AREA A
A3
1
2
3
LEVEL 1 HVAC PLAN - AREA C SCALE: 1/8" = 1'-0"
4
3.1
0'
5
4'
8'
16'
NORTH
INE CH L MAT
2/12/2016 10:52:07 AM
NORTH
SHEET NO.
MH101C 6
1
2
3
4
5
6
GENERAL SHEET NOTES 1.9 2
3
4
5 5.1 A.
REFER TO SHEET M001 FOR GENERAL NOTES.
1 M301
0.5
20"x20"
1.9
2
3
4
5 5.1
20"x20"
1,115 lb. FOR FUTURE
E
1
RTU-01B
1
Z Y.9
RTU-01A
1,115 lb. FOR FUTURE
20"x20" 20"x20"
1
1
Z
RTU-02
1,125 lb.
Y.9
SHEET KEYNOTES Y
NORTH
D2
ROOF MECHANICAL PLAN - AREA C ALT SCALE: 1/8" = 1'-0"
3.
20"x20" RTU-04
20"x20"
0'
4'
8'
1,125 lb.
16'
RTU-05
W.2
4.
1
1,125 lb.
2
5.
6.
W.1
7.
EF-01
65 lb.
W
CU-02
1
95 lb.
OF
1
PROJECT
3
RTU-06 CU-01
1,125 lb.
3
95 lb.
1/2" RS 1/4" RL
U C
1
RTU-07
885 lb.
8"ø
T
EF-08
155 lb.
S
1
RTU-08
R
Abbas 2016.02.15 13:22:24-07'00'
V 1/2" RS 1/4" RL
102840 I C E N S E E SS G IO N A L E N
L
X
A
ABBAS SHIRIAN PR
2.
D
E O F T EX
S
1,115 lb.
AT
D
20"x20"
EE
RTU-02
IN
1,125 lb.
20"x20"
ARCHITECT
1,125 lb.
200 Longhorn Street Vega, TX 79092
1
PROVIDE ROOFTOP UNIT AND ROOF CURB. ENSURE CURB IS INSTALLED LEVEL FOR PROPER CONDENSATE DRAINAGE FROM UNIT. PROVIDE FLEXIBLE CONNECTORS ON THE SUPPLY AND RETURN AIR DUCT CONNECTIONS AND TRANSITION TO DUCT SIZES SHOWN AT LEVEL BELOW. FOR HORIZONTAL SUPPLY AND RETURN DUCTED UNITS, PROVIDE SHEET METAL SUN SHIELDS AROUND TOP AND SIDES OF FLEX CONNECTORS. PROPERLY SECURE SUN SHIELDS TO UNIT WITH SHEET METAL SCREWS. COORDINATE WITH STRUCTURE. REFER TO DETAILS AND EQUIPMENT SCHEDULE FOR ADDITIONAL INFORMATION.PROVIDE ROOF MOUNTED EXHAUST FAN AND ROOF CURB. INSTALL FAN LEVEL ON CURB. PROVIDE DUCT TRANSITION FROM FAN INLET TO DUCT SIZE INDICATED ON PLANS. EXTEND DUCT DOWN THRU ROOF. COORDINATE WITH STRUCTURE. REFER TO DETAIL AND EQUIPMENT SCHEDULE FOR ADDITIONAL INFORMATION. PROVIDE ROOF MOUNTED EXHAUST FAN AND ROOF CURB. INSTALL FAN LEVEL ON CURB. PROVIDE DUCT TRANSITION FROM FAN INLET TO DUCT SIZE INDICATED ON FLOOR PLANS. EXTEND DUCT DOWN THRU ROOF. COORDINATE WITH STRUCTURE. REFER TO DETAILS AND EQUIPMENT SCHEDULE FOR ADDITIONAL INFORMATION. PROVIDE REMOTE CONDENSING UNIT AND EQUIPMENT SUPPORT RAILS ON ROOF. INSTALL UNIT LEVEL. PROVIDE LIQUID AND VAPOR PIPING. SIZE PIPING, SUPPORT, TRAP AND SLOPE REFRIGERANT LINES PER MANUFACTURER'S INSTRUCTIONS. PROVIDE INSULATION ON REFRIGERANT LINES PER PROJECT SPECIFICATIONS. EXTEND REFRIGERANT PIPING THRU ROOF THRU A SHEET METAL HOOD. ENSURE PIPE THRU ROOF ENCLOSURE IS WEATHER-TIGHT. CONTRACTOR TO COORDINATE SHORTEST ROUTING TO INDOOR UNIT. PROVIDE CONTROL WIRING BETWEEN CONDENSING UNIT AND INDOOR UNIT AND ALL CONTROL COMPONENTS. PROVIDE ALL VALVES AND ACCESSORIES AS REQUIRED BY MANUFACTURER FOR A COMPLETE AND OPERATIONAL SYSTEM. REFER TO DETAILS AND EQUIPMENT SCHEDULE FOR ADDITIONAL INFORMATION. EXHAUST 4" DIA TYP B FLUE UP THROUGH ROOF, LOCAL VENT, & STORM COLLAR, FLASH & COUNTER FLASH WEATHERTIGHT. TERMINATE FLUE 5 FT ABOVE ROOF WITH BRIEDERT TYPE L FLUE CAP. 20"X20" (5/16" THICK) CARBON STEEL DUCT UP THROUGH ROOF. TERMINATE ABOVE ROOF WITH GOOSENECK OF SAME CONSTRUCTION. REFER TO STRUCTURAL REQUIREMENTS FOR ADDITIONAL REQUIREMENTS. 4" COMBUSTION AIR DUCT FROM WATER HEATER AT MECH ROOM. EXTEND COMBUSTION AIR DUCT UP APP.18" ABOVE ROOF AND TERMINATE WITH RAIN CAP. 4" FLUE FROM WATER HEATER AT MECH ROOM. EXTEND UP MIN. 36" ABOVE COMBUSTION AIR OPENING. PROVIDE AND INSTALL ROOF THIMBLE, ROOF JACK, FLASHING, COUNTER FLASHING, AND FLUE CAP.
VEGA ISD HIGH SCHOOL
RTU-03
ST
1.
1
EF-10 RTU-09
1,150 lb. 1
R 4
Q
B
4" FLUE FROM UNIT HEATER
7
P
6
N
1
RTU-10 RTU-10lb. 1,125
3
Addendum 004
3
M
REVISIONS EF-11
1
01/29/16
ADDENDUM #01
2
02/05/16
ADDENDUM #02
3
02/15/16
ADDENDUM #04
RTU-11
1,125 lb.
L
1
KEY PLAN - NTS
EF-07
155 lb. RTU-12 8"ø
J
1,125 lb.
1
DRAWN BY
A3 / MH141B
A3 / MH141B
NZ
REVIEWED BY GEF-02
RLM
AREA C
GEF-01
DATE
02.15.2016
PROJECT NO:
A
DRAWING NAME
MATCH LINE
3.1
14-0424.002
ROOF MECHANICAL PLAN - AREA C
AREA B AREA A
A3
1
2
3
ROOF MECHANICAL PLAN - AREA C SCALE: 1/8" = 1'-0"
0'
4
5
4'
8'
16'
NORTH
INE CH L MAT
2/12/2016 10:52:08 AM
NORTH
SHEET NO.
MH141C 6
1
2
3
4
5
GENERAL SHEET NOTES A. B.
A
B
C
D
D
E
F
AG-EF-02
SEE SHEET P700a FOR PLUMBING FIXTURE ROUGH-IN SCHEDULE. PROVIDE GAS SHUT-OFF VALVE DIRTLEG AND UNION AT GAS FIRED EQUIPMENT.
G
AG-EF-03 3/4" A
P9
1
P9a A
A
1 1/2" G
G
STORAGE 103
A
G 2" G
1 1/4" G
3/4" A 2 A
2
2 AG-RH-02 125 CFH
2" G
CLASSROOM 102
AG-RH-01 125 CFH
AG-RH-02 125 CFH
3/4" A
A
DCW
DCW
2
G
3/4" DCW
3
DCW
GIRLS 110
P3 P1 O R T E I-V 3 K 5 4 G H C _ C N H U A IS T L E
P2
AG-FC-01
A
DHWR
DHW
4
P9b
AG-UH-01 30 CFH
3/4" G
TOOL STORAGE 106 1
G AG-RH-05 125 CFH
3" G
P9
A
1" A
3
2" G
2
AG-RH-06 125 CFH
AG-RH-07 125 CFH
1 1/2" G
AG-RH-08 125 CFH 1 1/4" G
RISE AG-EF-04
6
1" G
3
1" A
G 3/4" A
P9a
2" DCW
5
Abbas 2016.02.15 13:19:08-07'00'
2
2" DCW
DCW
AG-RTU-01 80 CFH
AG-EF-05
AG-1 AD-1
AG-CU-01 ~
7
NORTH
AG SHOP PRESSURE PIPING PLAN
A1
102840 I C E N S E E SS G IO N A L E N
2" G
G
G
~ ~
3" G
P1a
O R T E I-V 3 K 5 4 G H C _ C N H U A IS T L E
4
3" G O R T E I-V 3 K 5 4 G H C _ C N H U A IS T L E
P1a
3
5
P14
DCW
2" DCW
8
A
PROJECT
10
2" DCW 5
3/4" DCW
E O F T EX
ABBAS SHIRIAN OF
3/4" DCW
ELEC./COMP. 107
9
P3 P9b BOYS 109 P3
DCW
AT
L
P3
DCW
DHW
JANITOR P4 108
DWH-1 65 CFH
C
3/4" DCW
2
VEGA ISD CAREER TECHNOLOGY BUILDING
P5
DCW
2
PR
DHW 3/4" DHWR
3/4" DCW
SEAL
SCALE: 1/8" = 1'-0"
0'
4'
8'
16'
B
200 LONGHORN ST. VEGA, TX 79092
DCW
1/2" DCW
1" DCW
DCW
1
1" DCW
DCW
1" DHW
2
2" G 2
ROUTE PIPING ABOVE CEILING. ROUTE PIPING HIGH IN CEILING SPACE. ROUTE PIPING BELOW GRADE. SEE CIVIL DRAWINGS FOR CONTINUATION. GAS METER/REGULATOR SIZED FOR 1175 CFH WITH AN ENTERING HIGH PRESSURE AND LEAVING PRESSURE OF 14" WC. INSTALL PETES PLUGS ON BOTH SIDES OF REGULATOR. REGULATOR SHALL BE VENT LIMITING TYPE. SEE DETAIL C2/P501a FOR GAS METER REGULATOR. 6. SEE DETAIL C4/P501a FOR AIR COMPRESSOR DETAIL. 7. CONDENSATE DRAIN FROM AIR COMPRESSOR SHALL DRAIN TO GRADE IN CODE COMPLIANT MANNER. 8. PROVIDE 18" X 18" ACCESS DOOR. 9. ROUTE FULL SIZE T&P DRAIN RELIEF VALVE TO MOP SINK. SEE DETAIL C1/P500a FOR DOMESTIC WATER HEATER. 10. SEE DETAIL C1/P501a FOR DOMESTIC WATER ENTRY ASSEMBLY.
S
HALLWAY 101
3/4" DCW
1. 2. 3. 4. 5.
R
SHOP 105
EE
1" A
D
2
IN
P6
2" DCW
SHEET KEYNOTES
P9 P9a
ST
OFFICE 104
AG-RH-04 125 CFH
Addendum 004 REVISIONS 4
02/05/16
ADDENDUM #02
5
02/15/16
ADDENDUM #04
DATE REVIEWED BY
AS
DATE
02.15.2016 14-0424.002
PROJECT NO:
DRAWING NAME
A
2/15/2016 12:52:58 PM
AG SHOP PRESSURE PIPING PLAN
SHEET NO
PP101 1
2
3
4
5
1
2
3
4
5
# 1"
1 6
DHW
# 1/1-4"
1-1/4"
# 3/4"
# 3/4"
DCW DCW
G
5
DHW
4
3/4"
# 3/4"
9
1.5 GPM
5
13 10 DHC
2 12
# 3/4"
DHC
D 7
3/4
1 5
5
5
G
D
3
1
# 3/4"
5
5 9
11
6" MIN.
1.5 GPM
5
7 5
2 8
FINISH FLOOR
4 2
14
FLOW
1
EXPANSION TANK P8
8
4" MIN. HOUSEKEEPING PAD
2
FULL SIZED T&P RELIEF VALVE INDIRECTLY DISCHARGED TO MOP SINK, 2X PIPE DIA.
9
CIRCUIT SETTER/BALANCING VALVE
10
PETE'S PLUGS (TYPICAL)
3
PLUG VALVE W/DIRT LEG
11
HEAT TRAP PER MFG. SPEC'S
4
THERMOMETER (TYPICAL)
12
UNION (TYPICAL)
2 3
4
FLOW
5
6
3
2
3
DOMESTIC WATER HEATER
C3
SCALE: 1/4" = 1'-0"
DUCTILE, CAST-IRON, OR PVC WATER
5
PIPE SLEEVE, SEE SPECIFICATIONS
6
MEGALUG PIPE RESTRAINT HARNESS
DUCTILE, CAST-IRON, OR PVC WATER SERVICE.
2 3
MECHANICAL JOINT FROM SUPPLY PIPE TO STAINLESS STEEL, CONTINUE INTO BUILDING WITH STAINLESS STEEL
WATER ENTRY BELOW FOOTING
C4
SCALE: 1/4" = 1'-0"
5
PIPE SLEEVE, SEE SPECIFICATIONS
6
MEGALUG PIPE RESTRAINT HARNESS
5
8
5
WATER ENTRY THRU FOOTING SCALE: 1/4" = 1'-0"
7
5
10
6 4
4 3
8 1 2
4
2
4
4
5
3
B
FINISHED WALL 9
9 1
8
9
12"-18" STAINLESS STEEL ACCESS COVER W/ COUNTERSUNK SCREW
7
1
10
10
FLOW
2
3
FLOOR DRAIN WITH ADJUSTABLE STRAINER, DOUBLE DRAINAGE FLANGE AND WEEP HOLES. SEE FLOOR DRAIN SPECIFICATIONS CLAMP TO 24"x24" AND WATERPROOFING MEMBRANE (NOT REQUIRED FOR SINGLE POUR CONSTRUCTION)
5
5
6
7
4
A1
CLEANOUT TEE
TRAP GUARD WATER SAVING DEVICE SIZED PER DRAIN (IF SPECIFIED)
CLEANOUT PLUG
5
FINISHED FLOOR SLOPED IN ACCORDANCE WITH ARCH. DRAWINGS. COORDINATE WITH STRUCTURAL
1
2
SEE PLUMBING FLOOR PLANS FOR SIZING AND P-TRAP REQUIREMENTS
CONCRETE FLOOR OF TWO POUR
3 8
FOUR BAND HEAVY DUTY CLAMP, SEE SPECIFICATIONS
CAULK AS REQUIRED ON INSTALLATION ABOVE GRADE
4
FLOOR DRAIN SCALE: 1/4" = 1'-0"
R
Addendum 004
FLOW 1
EE
PROJECT
6 7
3
102840 I C E N S E E SS G IO N A L E N
Abbas 2016.02.15 13:19:02-07'00'
MECHANICAL JOINT FROM SUPPLY PIPE TO STAINLESS STEEL, CONTINUE INTO BUILDING WITH STAINLESS STEEL.
6
2
ABBAS SHIRIAN D
SEISMIC STRAPPING PER UPC 508.2 (IF REQUIRED)
CONCRETE THRUST BLOCK SIZED IN ACCORDANCE WITH UBC IF REQUIRED BY AHJ
4
IN
DOMESTIC WATER HEATER, SEE SPEC'S (DWH-1)
NOTE: INSTALL THERMOSTATIC MIXING VALVE ASSEMBLY IN ACCORDANCE WITH MANUFACTURERS RECOMMENDATION. PROVIDE PIPING SCHEMATIC WITH SUBMITTALS
C1
AMES IN-BUILDING RISER. STAINLESS STEEL TYPE 304. SEE PLANS FOR SIZE AND SERVICE
1
OF
C
CONCRETE THRUST BLOCK SIZED IN ACCORDANCE WITH UBC IF REQUIRED BY
4
L
7
AMES IN-BUILDING RISER. STAINLESS STEEL TYPE 304. SEE PLANS FOR SIZE AND
PR
14
1
A
200 LONGHORN ST. VEGA, TX 79092
IN-LINE PUMP ILP-1
COMBUSTION AIR INTAKE AND FLUE BY MECHANICAL
E O F T EX
VEGA ISD CAREER TECHNOLOGY BUILDING
6
13
ST
THERMOSTATIC MIXING VALVE P10
AT
S
5
SEAL
6
A2
WALL CLEANOUT SCALE: 1/4" = 1'-0"
SERVICE LINE, SEE SPECIFICATIONS FOR PIPE MATERIALS. SAME SIZE AS SERVICE LINE, THRU 4" PIPE, MAXIMUM 4" SIZE REQUIRED. CAST IRON SOIL PIPE RISER AND FITTINGS. COMPACTED EARTH, SEE SPECIFICATIONS.
5 6 7
8
SERVICE LINE, SEE SPECIFICATIONS FOR PIPE MATERIALS.
5
CLEANOUT WITH HEAVY DUTY SCORIATED SECURED TOP .
2
SAME SIZE AS SERVICE LINE, THRU 4" PIPE, MAXIMUM 4" SIZE REQUIRED.
6
FINISH HARDSCAPE. SEE SITE PLAN DRAWINGS FOR ELEVATION.
CLEANOUT WITH HEAVY DUTY SCORIATED SECURED TOP . 2" CHAMFER ON ALL COLLARS IN EARTH. FINISH HARDSCAPE. SEE SITE PLAN DRAWINGS FOR ELEVATION.
3
CAST IRON SOIL PIPE RISER AND FITTINGS.
4" THICK CONCRETE PAD. 4
9
1/8TH BEND.
10
WYE FITTING.
DOUBLE CLEANOUT TO GRADE
A3
1
A4
SCALE: 1/4" = 1'-0"
COMPACTED EARTH, SEE SPECIFICATIONS.
7
18"X18"X4" THICK CONCRETE COLLAR.
8
1/8TH BEND.
9
WYE FITTING.
10
2" CHAMFER ON ALL COLLARS IN EARTH.
CLEANOUT TO GRADE
REVISIONS 4
02/05/16
ADDENDUM #02
5
02/15/16
ADDENDUM #04
DATE REVIEWED BY
AS
SCALE: 1/4" = 1'-0" DATE
02.15.2016 14-0424.002
PROJECT NO:
DRAWING NAME
A
2/15/2016 12:52:54 PM
PLUMBING DETAILS
SHEET NO
P500a 1
2
3
4
5
1
2
3
4
5
2
5
5
5
1
SEE PLANS FOR CONTINUATION
6 5
SEE PLAN PP101 FOR CONTINUATION
1
4
D
8
COMPRESSED AIR LINE
4
7
3
MAX. 5'-0" A.F.F.
PRESS. STICH UNION
FINISH GRADE
2
SEE PLANS FOR SIZE SEE CIVIL PLAN FOR CONTINUATION
FINISHED FLOOR HIGH PRESS. LINE SIZED BY GAS CO.
SEE PLANS FOR CONTINUATION
UNION (TYP.)
6
DUPLEX AIR COMP. AG-1
NOTE: COORDINATE INSTALLATION WITH LOCAL GAS UTILITY OFFICIALS AND CONFORM TO THEIR REQUIREMENTS. ANY VARIATION FOR METERING REQUIREMENTS SHALL BE AT THE GAS COMPANY'S DIRECTION.
MANUAL DRAIN VALVE SEAL
COMP. AIR FILTER @: MIN. 147 SCFM MAX PRESS. 232 PSI PROVIDE WALL SUPPORT FOR FILTER
PRESSURE GAUGE
7
SUB-METER AND UNIONS (IF REQUIRED)
8
PT PORT
1
PLUG VALVE
3
REGULATOR TO REDUCE INCOMING HIGH PRESSURE TO 14" W.C.
4
DRAIN
TEST TEE
AT
E O F T EX
A
ABBAS SHIRIAN 102840
OF
I C E N S E E SS G IO N A L E N Abbas 2016.02.15 13:18:55-07'00'
PETES PLUG 5
L
5
C
METER (SEE SITE PLAN FOR SIZE)
PR
2
PRESSURE REGULATOR
R
5
AIR DRYER, AD-1
EE
WYE STRAINER WITH BLOWDOWN VALVE AND HOSE THREAD
GAUGE COCK
5
S
3
LINE SIZE BALL VALVE
4
ELECT. HP. MOTOR
D
2
SLEEVE, MIN. 1" ABOVE FINISHED FLOOR AND SEAL WATER TIGHT
ASME PRESSURE RELIEF VALVE VIBRATION INSOLATOR PRESS. GAGE 0-200 PSI
IN
1
BELT GUARD
ST
1
AIR PRESSURE GAGE
NOTE: COORDINATE INSTALLATION WITH LOCAL GAS UTILITY OFFICIALS AND CONFORM TO THEIR REQUIREMENTS. ANY VARIATION FOR METERING REQUIREMENTS SHALL BE AT THE GAS COMPANY'S DIRECTION.
3
DOMESTIC WATER ENTRY ASSEMBLY
C2
SCALE: 1/4" = 1'-0"
GAS METER/REGULATOR SCALE: 1/4" = 1'-0"
C4
COMPRESSOR AND AIR DRYER ELEVATION
VEGA ISD CAREER TECHNOLOGY BUILDING
C1
SCALE: 1/4" = 1'-0"
B
200 LONGHORN ST. VEGA, TX 79092
PROJECT
Addendum 004 REVISIONS 4
02/05/16
ADDENDUM #02
5
02/15/16
ADDENDUM #04
DATE REVIEWED BY
AS
DATE
02.15.2016 14-0424.002
PROJECT NO:
DRAWING NAME
A
2/15/2016 12:52:56 PM
PLUMBING DETAILS
SHEET NO
P501a 1
2
3
4
5
3
4
5
PLUMBING FIXTURE SPECIFICATIONS
PLUMBING FIXTURE SPECIFICATIONS
PLUMBING FIXTURE SPECIFICATIONS
SYMBOL
SYMBOL
SYMBOL
P6 MULTI-STATION HAND SINK: TYPE: WALL HUNG, 5-STATION, 140 GA. 304 STAINLESS STEEL, ADJUSTABLE LEGS. MOUNTING BRACKET, 102"L X 18"W, 4" CENTER. MFG: BRADLEY NO. S96-051 (6951A-5) SERVICE RQRS:SUPPLY AND WASTE, 1-1/4" IPS. SUPPLY VALVE HANDLES REMOVED OR LOCKED OPEN. FAUCET: 4" CENTER, 4" UNTEGRAL SPOUT, CHROME PLATED, METAL WRISTBLADE HANDLES, 0.5 GPM VANDAL-PROOF AERATOR. MFG: CHICAGO NO. 802-VE2805-317ABCP
P2 URINAL: TYPE:
DESCRIPTION
WALL MOUNTED, SIPHON JET FLUSHING, VITREOUS CHINA, 3/4" TOP SPUD, LOW CONSUMPTION, 0.125 GALLON PER FLUSH. MFG: KOHLER K-4904-ET "BARDON" CARRIER: FLOOR SUPPORTED, CONCEALED IN WALL. MFG: ZURN, WADE, JOSAM OR SMITH. FLUSH VALVE:EXPOSED, MANUAL, CHROME PLATED FLUSHOMETER. 0.125 GALLON PER FLUSH. MTD HEIGHT: SEE ARCHITECTURAL DRAWINGS.
P7 WATER HAMMER ARRESTOR: TYPE: STAINLESS STEEL CONSTRUCTION, PRE-CHARGED, PERMANENTLY SEALED. SEE SHOCK ABSORBER SCHEDULE FOR UNIT SIZE MFG: JAY R. SMITH 5000 SERIES. NOTE: PROVIDE AND INSTALL BEHIND LOCKING 14"X14" ACCESS PANEL. P8 EXPANSION TANK: TYPE: PRE-PRESSURED TANK WITH SEALED-IN AIR CHARGE OF 55 PSI. SIZE: 2.1 GAL, TOTAL VOLUME, 0.9 MAX. ACCEPTANCE. MFG: AMTROL NO. ST-5-C.
P2a URINAL (HANDICAP): TYPE: SAME AS P2 EXCEPT MOUNTING HEIGHT. SEE ARCH. PLANS.
DOMESTIC WATER HEATER SCHEDULE SYMBOL
DWH-1
LOCATION
JANITOR 108
SERVICE
SET POINT
120°
140°
MANUFACTURER/ MODEL No.
TYPE
A.O. SMITH NO. BT-65
NATURAL GAS
STORAGE
BTUH
65 GAL
ALL SELECTIONS BASED ON 5300 FT. ELEVATION
ELECTRICAL DATA
HW RECOVERY
OPERATING WEIGHT
POWER
Kw
Hz
PH
780 LBS
-
-
-
-
65,000
GPH RATE 67 GPH
PUMP SCHEDULE
INSTALL ON 4" HOUSE KEEPING PAD, ROUTE T&P RELIEF VALVE TO NEAREST FLOOR SINK, PROVIDE CONDENSATE NEUTRALIZATION KIT
ALL SELECTIONS BASED ON 5300 FT. ELEVATION
ELECTRICAL DATA SYMBOL
DESCRIPTION
LOCATION
TYPE
FLOW
TOTAL HEAD(FT) ILP-1
INLINE PUMP
JANITOR 108
SIMPLEX
1.5 GPM
8
RPM
MOTOR HP
VOLT
PHASE
AMPS
1750
1/12
115
1
2.0
MANUFACTURER/ MODEL No.
BASIN SIZE
BELL & GOSSETT NO. 100
5
REMARKS 120° DOMESTIC HOT WATER RETURN, BRONZE FLANGED, 3/4" CONNECTION SIZE. COORDINATE CONNECTION OF BMS WITH ELECTRICAL
N/A
B
AIR COMPRESSOR SCHEDULE SYMBOL
AG-1
AD-1
LOCATION
OUTSIDE
OUTSIDE
SERVICE
COMPRESSED AIR
AIR DRYER
TYPE TANK MOUNTED DUPLEX
NA
MANUFACTURER/ MODEL No.
CAPACITY @ RECEIVER OPER. TANK PRESSURE GALLONS
QUINCY COMPRESSOR QT15-15-2000
51(x2) ACFM @ 175 PSIG
QUINCY COMPRESSOR QED-100
100 CFM @ 100 PSIG
200
NA
OPERATING WEIGHT (LBS)
1900
150
DESCRIPTION
ROUGH-IN SIZE
TEMP.RATE 90°
ALL SELECTIONS BASED ON 5300 FT. ELEVATION
MOTOR
102840 I C E N S E E SS G IO N A L E N
Abbas 2016.02.15 13:18:49-07'00'
PROJECT
PLUMBING ROUGH-IN SCHEDULE SYMBOL
REMARKS
CW
HW
WASTE
VENT
TRAP
REMARKS
P1
WATER CLOSET - HANDICAP
1"
-
4"
2"
INTEGRAL
FLOOR MOUNT, CONCEALED MANUAL FLUSH, 1.6 GPF
P1a
WATER CLOSET - HANDICAP
1"
-
4"
2"
INTEGRAL
FLOOR MOUNT, CONCEALED MANUAL FLUSH, 1.6 GPF
P2
URINAL
3/4"
-
2"
2"
INTEGRAL
WALL MOUNT, ELECTRONIC FLUSH VALVE, 0.125 GPF
P2a
URINAL - HANDICAP
3/4"
-
2"
2"
INTEGRAL
WALL MOUNT, ELECTRONIC FLUSH VALVE, 0.125 GPF
P3
LAVATORY - HANDICAP
1/2"
1/2"
2"
1-1/2"
1-1/4" X 1-1/2"
P4
SERVICE SINK
3/4"
1/2"
2"
2"
3"
P5
DRINKING FOUNTAIN
1/2"
-
2"
1-1/2"
1-1/4"
P6
MULTI-STATION HAND SINK
1/2"
1/2"
2"
2"
1-1/2" X 1-1/2"
P7
WATER HAMMER ARRESTOR
PDI
-
-
-
-
INSTALL IN 14"X14" ACCESS PANEL
P8
EXPANSION TANK
3/4"
-
-
-
-
CENTRAL STERILE IHW SYSTEM
P9
WALL HYDRANT
3/4"
-
-
-
-
NON-FREEZE
A S
P4 SERVICE SINK: TYPE: FLOOR MOUNTED, 24" X 24" X 10" DEEP, MOLDED STONE, 3" DRAIN OPENING. MFG: FIAT NO. MSB-2424. FAUCET: POLISHED CHROME, WALL MOUNTED 42" ABOVE FLOOR, WALL BRACE, VACUUM BREAKER, INTEGRAL CHECK STOPS. MFG: CHICAGO NO. 897-CP-C. DRAIN: INTEGRAL WITH STAINLESS STEEL STRAINER. TRAP: 3" CAST IRON "P" TRAP. ACCESSORIES: HOSE AND HOSE BRACKET NO. 832AA, STAINLESS STEEL, 24" X 3" MOP HANGER NO. 889-CC, VINYL BUMPER GUARD NO. E-77-AA.
P9b HOSE BIBB: TYPE: SILL FAUCET WITH VACUUM BREAKER, 3/4" GARDEN HOSE OUTLET WITTH ATMOSPHERIC NON REMOVABLE VACUUM BREAKER, 1/2" IPS FEMALE FLANGED INLET, CONTROLLED KEY, BRASS FINISH. MFG: CHICAGO NO. 5T REQUIREMENTS: 1/2" CW
E O F T EX
ABBAS SHIRIAN OF
C
AT
L
P9a HOSE BIBB: TYPE: SILL FAUCET WITH VACUUM BREAKER, 3/4" GARDEN HOSE OUTLET WITTH ATMOSPHERIC NON REMOVABLE VACUUM BREAKER, 1/2" IPS FEMALE FLANGED INLET, CONTROLLED BY LOOS KEY HANDEL, POLISHED CHROME FINISH. MFG: CHICAGO NO. 5T REQUIREMENTS: 1/2" CW
SEAL
PR
P3 LAVATORY (HANDICAP): TYPE: WALL HUNG, VITREOUS CHINA, 21" X 18" OVERALL DIMENSIONS, 3-HOLE, 4"CENTERS. MFG: KOHLER NO. K-2005 "KINGSTON". FAUCET: 4" CENTERS, METAL WRISTBLADE HANDLES, CHROME PLATED, 0.5 GPM LAMINAR FLOW AERATOR MFG: CHICAGO No. 802-317CP SUPPLIES: 1/2" SWEAT WHEEL HANDLE ANGLE STOPS WITH 3/8" O.D. FLEXIBLE RISERS, CHROME PLATED FINISH. TRAP: 1-1/4" IN X 1-1/2" OUT, 17 GA, CHROME PLATED, ADJUSTABLE, CLEANOUT PLUG, SEMI-CAST P-TRAP. MFG: MCGUIRE NO. 8902. MTD HEIGHT: SEE ARCHITECTURAL DRAWINGS FOR MOUNTING HEIGHT. NOTE: INSULATE SUPPLY AND WASTE PIPING PER SPECIFICATIONS.
P9 WALL HYDRANT: TYPE: BRONZE HYDRANT, FREEZE-PROOF, INTEGRAL VACUUM BREAKER, WITH LOOSE-KEY, 3/4" INLET AND 3/4" GARDEN HOSE OUTLET, LOOSE KEY HANDLE, VERIFY WALL THICKNESS BEFORE ORDERING. MFG: ZURN NO. Z-1310.
R
FD1 FLOOR DRAIN: TYPE: 7" DIAMETER, ROUND TYPE "B" STRAINER. POLISHED BRONZE, CAST IRON BODY WITH BOTTOM OUTLET, COMBINATION INVERTABLE MEMBRANE CLAMP, DEEP SEAL P-TRAP, VANDAL-PROOF SECURED TOP, DIAMETER OF OUTLET AS SHOWN ON DRAWINGS. MFG: ZURN NO. Z-415-B-VP-Z1000. NOTE: PROVIDE WITH PROSET TRAP GUARD WATER SAVING DEVICE. SIZE AS INDICATED BY DRAIN.
EE
SYMBOL
D
FLOOR DRAIN/SINK SPECIFICATIONS
P1a WATER CLOSET (PUBLIC RESTROOMS-HANDICAP): TYPE: SAME AS Pb EXCEPT MOUNTING HEIGHT. SEE ARCH. PLANS.
IN
D
P1 WATER CLOSET: TYPE: FLOOR MOUNT, SIPHON JET, 1-1/2" TOP-SPUD, 1.28 GALLON PER FLUSH, ELONGATED, VITREOUS CHINA, MFG: KOHLER NO. K-4405 "HIGHLINE". SEAT: SOLID PLASTIC, OPEN FRONT, FIRE RETARDANT, ELONGATED, WITHOUT COVER, STAINLESS STEEL CHECK HINGE. MFG: OLSONITE NO. 95. FLUSH VALVE: EXPOSED, MANUAL, CHROME PLATED, DIAPHRAGM TYPE, FLUSHOMETER, 1.28 GALLON PER FLUSH. MFG: SLOAN NO. 111-1.28 "ROYAL" CARRIER: ZURN, WADE JOSAM OR SMITH (1,000 LBS. CAPACITY) MTD. HEIGHT: SEE ARCHITECTURAL DRAWINGS.
P5 DRINKING FOUNTAIN (HANDICAP): TYPE: WALL HUNG, ADA COMPLIANT, BI-LEVEL, FRONT PUSH BUTTON, 18 GA. STAINLESS STEEL, VANDAL RESISTANT CHROME PLATED BUBBLER, VANDAL RESISTANT BOTTOM PLATES, INLINE STRAINER, WITH BOTTLE FILLING STATION. MFG: ELKAY EZH20 VRCGRNTL8WSK ACCESSORY: APRON LKAPREZL SUPPLIES: 1/2" X 3/8" WHEEL ANGLE STOPS WITH 3/8" O.D. FLEX RISERS. TRAP: 1-1/4" 17 GA. POLISHED CHROME TUBULAR P-TRAP. CARRIER:CONCEALED BY ZURN, WADE, JOSAM, OR SMITH. MTD HEIGHT: SEE ARCHITECTURAL DRAWINGS.
COUNTERTOP, MANUAL FAUCET, 0.5 GPM LAMINAR AERATOR FLOOR MOUNTED, CORNER TYPE, INTEGRAL CHECK STOPS BI-LEVEL HANDICAPPED ACCESSIBLE WALL HUNG, STAINLESS STEEL
200 LONGHORN ST. VEGA, TX 79092
P10 THERMOSTATIC MIXING ASSEMBLY (DOMESTIC HOT WATER): TYPE: HIGH LOW DUAL STAGE THERMOSTATIC WATER MIXING SYSTEM SET FOR 120F. LARGE AND SMALL TYPE THERMOSTATIC WATER MIXING VALVES, ADJUSTABLE HIGH TEMPERATURE LIMIT STOP, INLET CHECKSTOPS, WALL SUPPORT, OUTLET BALL VALVE, 1 GPM MINIMUM FLOW CAPACITY, INLET MANIFOLD PIPING, OUTLET PRESSURE REGULATING VALVE AND PRESSURE GAUGES, COLOR-COATED DIAL THERMOMETER (0 TO 140F), FACTORY ASSEMBLED AND TESTED, ROUGH FINISH. INLET: 3/4". OUTLET: 1". MFG: LEONARD NO. TM-420A-LF-DT-IT-RF
DESCRIPTION
VEGA ISD CAREER TECHNOLOGY BUILDING
2
ST
1
REMARKS
HP
RPM
VOLTS/FLA
PH
HZ
15
923
460V
3
60
NA
223
115V
1
60
Addendum 004 INSTALL ON 4" HOUSE KEEPING PAD. AUTO LAG. ALTERNATOR PANEL, STARTER, FUSED DISCONNECTS, DOOR INTERLOCK, 120V CONTROL TRANSFORMER, NEMA 4 ENCLOSURE, START/STOP SWITCH, MANUAL DRAIN, DISCHARGE FLEX HOSE WITH DYER, FILTER, REGULATOR SYSTEM.
REVISIONS 4
02/05/16
ADDENDUM #02
5
02/15/16
ADDENDUM #04
INSTALL ON 4" HOUSE KEEPING PAD.
DATE REVIEWED BY
AS
DATE
02.15.2016 14-0424.002
PROJECT NO:
DRAWING NAME
A
2/15/2016 12:52:57 PM
PLUMBING SCHEDULES
SHEET NO
P700a 1
2
3
4
5
1
2
3
4
5
6
GENERAL SHEET NOTES A. B.
C.
D. E. F.
G.
E
H.
G R2.9
4
ALL HOT AND COLD WATER DROPS/RISES TO FIXTURES SHALL BEVERTICAL BETWEEN THE FRAMING STUDS. ALL WASTE, VENT, AND WATER PIPING IN PIPE CHASE SHALL BE RACKED TIGHT TO INTERIOR FRAME WALL, LEAVING CENTER OF CHASE CLEAR FOR MAINTENANCE. ANY CROSSOVER SHALL BE 7'-0 A.F.F. TO BOTTOM OF PIPE MINIMUM. PROVIDE BALL VALVES FOR ALL WATER ISOLATION AND SUPPLY TAKE-OFFS. ISOLATION VALVES FOR BRANCH PIPING TO BE LOCATED ABOVE LAYIN CEILING FOR EASY ACCESS BY MAINTENANCE. ISOLATION VALVES THAT CAN NOT BE LOCATED ABOVE LAY-IN CEILING MUST BE PROVIDED MAINTENANCE ACCESS IN THE FORM OF AN ACCESSIBLE PLUMBING CHASE OR AN ACCESS PANEL. ALL EQUIPMENT DRAINS AND SHOCK ABSORBERS SHALL HAVE MAINTENANCE ACCESS IN THE FORM OF AN ACCESSIBLE PLUMBING CHASE OR AN ACCESS PANEL. FLOOR DRAINS SHALL BE INSTALLED WITH NICKEL BRONZE AND HEEL PROOF GRATES. COORDINATE ALL VTR'S WITH MECHANICAL FRESH AIR INTAKES ON ROOF. VENTS SHALL MAINTAIN A MINIMUM OF 12'-0" CLEARANCE. SEE SPECIFICATION SECTION 23 0548, SEISMIC RESTRAINT AND VIBRATION ISOLATION, FOR PROJECT SEISMIC RESTRAINT REQUIREMENTS. WATER HEATERS SHALL BE ANCHORED OR STRAPPED TO RESIST HORIZONTAL DISPLACEMENT DUE TO EARTHQUAKE MOTION, STRAPPING SHALL BE AT POINTS WITHIN THE UPPER ONE-THIRD AND LOWER ONETHIRD OF ITS VERTICAL DIMENSIONS. AT THE LOWER POINT, A DISTANCE OF NOT LESS THAN FOUR INCHES SHALL BE MAINTAINED ABOVE THE CONTROLS WITH STRAPPING. ALL COUNTERTOP AND WALL MOUNTED PLUMBING FIXTURES (URINALS, LAVATORIES, COUNTERTOP MOUNTED SINKS, DRINKING FOUNTAINS, ETC.) SHALL BE PROVIDED WITH A T-PATTERN WALL CLEANOUT BELOW PLUMBING FIXTURE. CLEANOUT SHALL BE CAST IRON DRAINAGE T-PATTERN, 90 DEGREE BRANCH FITTINGS WITH SQUARE HEAD BRASS SCREW PLUGS OF THE SAME SIZE AS THE PIPE UP TO AND INCLUDING 4 INCHES, PER SPECIFICATION 22 1300. WALL CLEANOUTS IN FINISHED AREAS SHALL BE ZURN No. Z-1460-8 WITH POLISHED STAINLESS STEEL OR CHROME PLATED METAL COVER.
RV
~
FCO
3 3.1
5 P402
GIRLS B112
SAN
RU
GIRLS JV B113
4" SAN ~
~
SHEET KEYNOTES
FILM ROOM B107
1. 2.
REFER TO SEWAGE EJECTOR A5/P502. REFER TO ELEVATOR SUMP PUMP W/OIL INTERCEPTOR A2/P502.
5
ARCHITECT
3" V
XRB
~
ST
S
2 6 P401 P402
D
R
102840
Abbas 2016.02.15 13:26:35-07'00'
COACH RR B109
PA B102
A
I C E N S E E SS G IO N A L E N
OF
3" V
3" V
E O F T EX
L
R1.8
~
AT
ABBAS SHIRIAN
GIRLS COACH B108
PR
R2
D
4" SAN
~
B L100 P / A3
R7
EE
4" SAN
~
3" V
IN
GIRLS VARSITY B111
CORRIDOR B106
PROJECT
4" SAN
SAN
HALL B100A
RU
~
RS FILM ROOM B118
WCO SAN
RR ~
STOR B103
BOYS VARSITY B122
RQ RP GYMNASIUM B100
4" SAN
SAN
C
5
~
SANITARY PIPING IN CEILING SPACE
~
4" SAN SAN
4" SAN
HALL B100B
RN
~
4" SAN GI-1 ~
PD
2" V
RM
2" V
A
2" PD
~
4" SAN PIPING UP TO CEILING SPACE
~
2
OFFICIALS RR B129
OFFICIALS B128
200 Longhorn Street Vega, TX 79092
RT
VEGA ISD HIGH SCHOOL
BOYS COACH B119
3" FS1
1
B L100 P / A3
RK
SEWAGE EJECTOR (SEP-1)
B
RJ RG Addendum 004 RF REVISIONS
RE
4
02/05/16
ADDENDUM #02
5
02/15/16
ADDENDUM #04
KEY PLAN - NTS
AREA C
EXISTING
DRAWN BY
SP
REVIEWED BY
AS
DATE
R2.1
LEVEL 1 ABOVE MATCH LINE
A
02.15.2016
PROJECT NO:
14-0424.002
DRAWING NAME
LOWER LEVEL WASTE & VENT FLOOR PLAN AREA A
AREA B AREA A
A3
LOWER LEVEL WASTE & VENT FLOOR PLAN - AREA A SCALE: 1/8" = 1'-0"
0'
1
2
3
4
5
4'
8'
16'
NORTH
E NE H LLIIN CH ATTC M MA
2/15/2016 1:02:53 PM
NORTH
SHEET NO.
PL100A 6
1
2
3
4
5
6
GENERAL SHEET NOTES A. B.
C.
D. E. F.
G.
E
H.
ALL HOT AND COLD WATER DROPS/RISES TO FIXTURES SHALL BEVERTICAL BETWEEN THE FRAMING STUDS. ALL WASTE, VENT, AND WATER PIPING IN PIPE CHASE SHALL BE RACKED TIGHT TO INTERIOR FRAME WALL, LEAVING CENTER OF CHASE CLEAR FOR MAINTENANCE. ANY CROSSOVER SHALL BE 7'-0 A.F.F. TO BOTTOM OF PIPE MINIMUM. PROVIDE BALL VALVES FOR ALL WATER ISOLATION AND SUPPLY TAKE-OFFS. ISOLATION VALVES FOR BRANCH PIPING TO BE LOCATED ABOVE LAYIN CEILING FOR EASY ACCESS BY MAINTENANCE. ISOLATION VALVES THAT CAN NOT BE LOCATED ABOVE LAY-IN CEILING MUST BE PROVIDED MAINTENANCE ACCESS IN THE FORM OF AN ACCESSIBLE PLUMBING CHASE OR AN ACCESS PANEL. ALL EQUIPMENT DRAINS AND SHOCK ABSORBERS SHALL HAVE MAINTENANCE ACCESS IN THE FORM OF AN ACCESSIBLE PLUMBING CHASE OR AN ACCESS PANEL. FLOOR DRAINS SHALL BE INSTALLED WITH NICKEL BRONZE AND HEEL PROOF GRATES. COORDINATE ALL VTR'S WITH MECHANICAL FRESH AIR INTAKES ON ROOF. VENTS SHALL MAINTAIN A MINIMUM OF 12'-0" CLEARANCE. SEE SPECIFICATION SECTION 23 0548, SEISMIC RESTRAINT AND VIBRATION ISOLATION, FOR PROJECT SEISMIC RESTRAINT REQUIREMENTS. WATER HEATERS SHALL BE ANCHORED OR STRAPPED TO RESIST HORIZONTAL DISPLACEMENT DUE TO EARTHQUAKE MOTION, STRAPPING SHALL BE AT POINTS WITHIN THE UPPER ONE-THIRD AND LOWER ONETHIRD OF ITS VERTICAL DIMENSIONS. AT THE LOWER POINT, A DISTANCE OF NOT LESS THAN FOUR INCHES SHALL BE MAINTAINED ABOVE THE CONTROLS WITH STRAPPING. ALL COUNTERTOP AND WALL MOUNTED PLUMBING FIXTURES (URINALS, LAVATORIES, COUNTERTOP MOUNTED SINKS, DRINKING FOUNTAINS, ETC.) SHALL BE PROVIDED WITH A T-PATTERN WALL CLEANOUT BELOW PLUMBING FIXTURE. CLEANOUT SHALL BE CAST IRON DRAINAGE T-PATTERN, 90 DEGREE BRANCH FITTINGS WITH SQUARE HEAD BRASS SCREW PLUGS OF THE SAME SIZE AS THE PIPE UP TO AND INCLUDING 4 INCHES, PER SPECIFICATION 22 1300. WALL CLEANOUTS IN FINISHED AREAS SHALL BE ZURN No. Z-1460-8 WITH POLISHED STAINLESS STEEL OR CHROME PLATED METAL COVER.
SHEET KEYNOTES SEE DETAIL A2/P502 FOR ELEVATOR SUMP PUMP W/OIL INTERCEPTOR. CONDENSATE DRAIN FROM FAN COIL UNITS (FC) SHALL DRAIN TO SERVICE SINK IN CODE COMPLIANT MANNER.
ARCHITECT 5 AT
E O F T EX
A S
ST
1. 2.
ABBAS SHIRIAN R
D
Abbas 2016.02.15 13:26:23-07'00'
R8
R7
EE
OF
R9
L
D
IN
PR
102840 I C E N S E E SS G IO N A L E N
XRB
PROJECT
R6
R5 20
R3
RT P1 ~
FCO
P3
P1a
P3
1 P401
P1
RS
TRAINING B116
SAN
GIRLS FD1 B112 GIRLS JV B113
4" SAN
P8
FD1
RR
UNIFORM STOR B114
FD1
P11
~
GIRLS VARSITY B111
4" SAN
2" SAN
~
3" V SAN FILM ROOM B107
ELEC B121
3" V
P9
0A PL10 A3 /
FD1
P8
5 FC-04
ELEV 714
3" V
COACH RR B109 ~
3" V
3" V
2 P401
P3
3" V
JANITOR B115
~
PA B102
GIRLS COACH B108
~
P1a
FC-05
3" V
4" SAN
RP
2" V
2
C
RQ
2" SAN
2" V
CORRIDOR B106
4" VENT UP TO FIRST FLOOR 5" V
1
3" V
RN
4" SAN
SAN
4" V
HALL B100A P11
UNIFORM STOR B120
BOYS COACH B119
RM
200 Longhorn Street Vega, TX 79092
P1
VEGA ISD HIGH SCHOOL
P3
P3
2" PD ~
RK
PD
2" SAN
SAN
5 IN CEILING SPACE
FILM ROOM B118
WCO SAN
P8
BOYS JV B124
FD2
3 P401 4" V
~
STOR B103
FD2
BOYS VARSITY B122
B
4" V 4" V
FD1
P3
CORRIDOR B132
~
HALL B100B
FD1 P8
~
FD1
PD
~
~
2" V
P3
P1a
2" PD FD1
2" PD
OFFICIALS RR B129
P3
OFFICIALS B128
P1 P1a
Addendum 004
4 P401
REVISIONS 4
02/05/16
ADDENDUM #02
5
02/15/16
ADDENDUM #04
FD1
IN CEILING SPACE PD
4" SAN
~
RG RF
P8
~
SAN
4" SAN
SAN
2" PD
4" SAN 4" SAN
2" V
~
4" SAN
P2
P2a
4" V
FC-06
4" V
~
SAN
SANITARY PIPING IN CEILING SPACE
4" SAN PIPING UP TO CEILING SPACE
P3
P1 P3
GI-1
PD
P3
P1a 4" SAN
RJ
3" V
BOYS B123
P1a IN CEILING BOYS VISITOR SPACE B131
P3
RE
P2a
KEY PLAN - NTS
P3
GIRLS VISITOR B133
P3
3" FS1 SEWAGE EJECTOR (SEP-1)
P8
DRAWN BY
SP
REVIEWED BY
AS
0A PL10 / 3 A
DATE
A
LEVEL 1 ABOVE
02.15.2016
PROJECT NO:
14-0424.002
DRAWING NAME
LOWER LEVEL WASTE & VENT FLOOR PLAN AREA B
AREA B
R2.9
AREA A
0'
1
2
3
A3
LOWER LEVEL WASTE & VENT FLOOR PLAN - AREA B 4
SCALE: 1/8" = 1'-0"
5
4'
8'
16'
NORTH
INE CH L MAT
2/15/2016 1:02:55 PM
NORTH
SHEET NO.
PL100B 6
1
2
3
4
5
6
GENERAL SHEET NOTES A. B.
C.
P18
D. E. F.
P17 ~
A3 / PL101C
A3 / PL101C
G.
J
E
H.
3" GW P7 5
LIFESKILLS 130
5 P401
CLASSROOM 129
RR 130A
~
P8
2" V
4" SAN P7
4" SAN
P7
~
3" GW 2
4" SAN
~
2472
STOR 128A
P4
4" RD/ORD 2448
STOR 128B
4" ORD 4" RD
1
H
2" V
2" V
RD ORD
STOR 129A
P7
P3
SAN
RD ORD
3
2" SAN
3"FD1
2" V P5
P5
2" V
4" RD/ORD
STOR 125A
2472
4" DN1
SAN ~
2472
DCOTG
P1a
5
2" SAN
1
2" SAN
SHEET KEYNOTES
1 1/2" V
2448
4" SAN SAN
WARMING KITCHEN 128
2" SAN 2" SAN
ARCHITECT
RT
MEDIA CENTER 125
AT
E O F T EX
A
ABBAS SHIRIAN
~
OF
ART 123
102840 I C E N S E E SS G IO N A L E N
RS
L
G
PR
4" V
4" ROOF DRAIN/OVERFLOW DRAIN LEADER FROM ABOVE. REFER TO CIVIL DRAWING FOR CONTINUATION. 4" ROOF DRAIN/OVERFLOW DRAIN LEADER DOWN IN WALL TO DOWN SPROUT NOZZLE 6" ROOF DRAIN/OVERFLOW DRAIN LEADER DOWN IN WALL TO DOWN SPROUT NOZZLE.
S
P6 SAN
2" V
6 P401
D 4" V
1. 2. 3. 4.
P4
2" SAN
CONCESSION 127
A3 / PL101A
G.9
R
2" V
SAN
SAN
2" SAN
STOR 130B
D
2" SAN
ST
P7
EE
3" GW
IN
LAB 131
ALL HOT AND COLD WATER DROPS/RISES TO FIXTURES SHALL BEVERTICAL BETWEEN THE FRAMING STUDS. ALL WASTE, VENT, AND WATER PIPING IN PIPE CHASE SHALL BE RACKED TIGHT TO INTERIOR FRAME WALL, LEAVING CENTER OF CHASE CLEAR FOR MAINTENANCE. ANY CROSSOVER SHALL BE 7'-0 A.F.F. TO BOTTOM OF PIPE MINIMUM. PROVIDE BALL VALVES FOR ALL WATER ISOLATION AND SUPPLY TAKE-OFFS. ISOLATION VALVES FOR BRANCH PIPING TO BE LOCATED ABOVE LAYIN CEILING FOR EASY ACCESS BY MAINTENANCE. ISOLATION VALVES THAT CAN NOT BE LOCATED ABOVE LAY-IN CEILING MUST BE PROVIDED MAINTENANCE ACCESS IN THE FORM OF AN ACCESSIBLE PLUMBING CHASE OR AN ACCESS PANEL. ALL EQUIPMENT DRAINS AND SHOCK ABSORBERS SHALL HAVE MAINTENANCE ACCESS IN THE FORM OF AN ACCESSIBLE PLUMBING CHASE OR AN ACCESS PANEL. FLOOR DRAINS SHALL BE INSTALLED WITH NICKEL BRONZE AND HEEL PROOF GRATES. COORDINATE ALL VTR'S WITH MECHANICAL FRESH AIR INTAKES ON ROOF. VENTS SHALL MAINTAIN A MINIMUM OF 12'-0" CLEARANCE. SEE SPECIFICATION SECTION 23 0548, SEISMIC RESTRAINT AND VIBRATION ISOLATION, FOR PROJECT SEISMIC RESTRAINT REQUIREMENTS. WATER HEATERS SHALL BE ANCHORED OR STRAPPED TO RESIST HORIZONTAL DISPLACEMENT DUE TO EARTHQUAKE MOTION, STRAPPING SHALL BE AT POINTS WITHIN THE UPPER ONE-THIRD AND LOWER ONETHIRD OF ITS VERTICAL DIMENSIONS. AT THE LOWER POINT, A DISTANCE OF NOT LESS THAN FOUR INCHES SHALL BE MAINTAINED ABOVE THE CONTROLS WITH STRAPPING. ALL COUNTERTOP AND WALL MOUNTED PLUMBING FIXTURES (URINALS, LAVATORIES, COUNTERTOP MOUNTED SINKS, DRINKING FOUNTAINS, ETC.) SHALL BE PROVIDED WITH A T-PATTERN WALL CLEANOUT BELOW PLUMBING FIXTURE. CLEANOUT SHALL BE CAST IRON DRAINAGE T-PATTERN, 90 DEGREE BRANCH FITTINGS WITH SQUARE HEAD BRASS SCREW PLUGS OF THE SAME SIZE AS THE PIPE UP TO AND INCLUDING 4 INCHES, PER SPECIFICATION 22 1300. WALL CLEANOUTS IN FINISHED AREAS SHALL BE ZURN No. Z-1460-8 WITH POLISHED STAINLESS STEEL OR CHROME PLATED METAL COVER.
Abbas 2016.02.15 13:26:13-07'00'
PROJECT
4" VTR
SAN
VEST 124
RR 4" SAN ~
RQ
STOR 123A
KILN 123B
P1a
5 P403
P3 P1
P1 P2a
1
BOYS 118
4" RD/ORD 7 P401
P2 P1
FD1 P3
P2
RP
COMPUTER LAB 121
P3 FD1 GIRLS 119
P1
P3
E
P3
CORRIDOR A132
ELEC 117A
D.2 12
P1
P2
P10 P9
D
~
4" RD 4" ORD
ORD RD
4" SAN RD ORD
SAN
P3
STUDENT COMMONS 102
2" SAN 3"FD1 2" V P1a 4" SAN
ELEV 721 2" SAN
1
CLASSROOM 122
5" V UP FROM BELOW
RM
5" V
RK 3" V
3" V
FAM RR 116
RC RC
RN
4" RD/ORD 4" ORD 4" RD
C
5" V
4" SAN
OFFICE 115
TEST STOR 115A
M 122B W 122A
1 3"FD P1a
STAIR 1 713 4" SAN
1 3"FD P3
STAGE A124 1 7 P403 P402
P1a
P3 P3
3" V ~
FILES 113
P3
W 108
P1a 1 3"FD
RJ
1 3"FD
P1a
~
SAN
ORD RD
5" V
CONF 103A
STOR 122C
200 Longhorn Street Vega, TX 79092
P1
VEGA ISD HIGH SCHOOL
F
P1a
M 112
STOR 111
RG
CORRIDOR 106
5" V
C
4" SAN
RECEPTION 103 B
CORRIDOR 110
4" RD/ORD 4" SAN
2" SAN SAN
4" ORD 4" RD
5" V
RD ORD
1
ISS 107
SAN
5" VTR
4" SAN PIPING UP FROM SUMP PUMP BELOW
PROP STOR A125
P4
Addendum 004
RD
LOUNGE 109A
PRINC 105
VEST 101
2" V 2" SAN
5" V
RD ORD
RE
SAN 2" V
4" SAN
4" SAN
RF
WORKROOM 109
REVISIONS
B
RECEPTION 103
A
4
02/05/16
ADDENDUM #02
5
02/15/16
ADDENDUM #04
KEY PLAN - NTS TRACK 156
STOR 164 ORD RD
R9 R7
R8
R8.1 910
20
R2.9
A
R3
R5
11
AREA C
DRAWN BY
SP
REVIEWED BY
AS
EXISTING DATE
02.15.2016
PROJECT NO:
R6
14-0424.002
DRAWING NAME
MATCH LINE
LEVEL 1 WASTE & VENT PLAN AREA B
4 AREA B AREA A
A3
1
2
3
LEVEL 1 WASTE & VENT PLAN - AREA B SCALE: 1/8" = 1'-0"
0'
4
5
4'
8'
16'
NORTH
INE CH L MAT
2/15/2016 1:02:58 PM
NORTH
SHEET NO.
PL101B 6
1
2
3
4
5
6
GENERAL SHEET NOTES 1.9
2
3
4
5
A. B.
5.1
C.
D. E. F.
G.
E
VEST H.
A153
CLASSROOM
CLASSROOM
A151
A150
1
0.5
STOR
CORRIDOR
STOR
A151A
A152
A150A
1.9
2
3
4
ALL HOT AND COLD WATER DROPS/RISES TO FIXTURES SHALL BEVERTICAL BETWEEN THE FRAMING STUDS. ALL WASTE, VENT, AND WATER PIPING IN PIPE CHASE SHALL BE RACKED TIGHT TO INTERIOR FRAME WALL, LEAVING CENTER OF CHASE CLEAR FOR MAINTENANCE. ANY CROSSOVER SHALL BE 7'-0 A.F.F. TO BOTTOM OF PIPE MINIMUM. PROVIDE BALL VALVES FOR ALL WATER ISOLATION AND SUPPLY TAKE-OFFS. ISOLATION VALVES FOR BRANCH PIPING TO BE LOCATED ABOVE LAYIN CEILING FOR EASY ACCESS BY MAINTENANCE. ISOLATION VALVES THAT CAN NOT BE LOCATED ABOVE LAY-IN CEILING MUST BE PROVIDED MAINTENANCE ACCESS IN THE FORM OF AN ACCESSIBLE PLUMBING CHASE OR AN ACCESS PANEL. ALL EQUIPMENT DRAINS AND SHOCK ABSORBERS SHALL HAVE MAINTENANCE ACCESS IN THE FORM OF AN ACCESSIBLE PLUMBING CHASE OR AN ACCESS PANEL. FLOOR DRAINS SHALL BE INSTALLED WITH NICKEL BRONZE AND HEEL PROOF GRATES. COORDINATE ALL VTR'S WITH MECHANICAL FRESH AIR INTAKES ON ROOF. VENTS SHALL MAINTAIN A MINIMUM OF 12'-0" CLEARANCE. SEE SPECIFICATION SECTION 23 0548, SEISMIC RESTRAINT AND VIBRATION ISOLATION, FOR PROJECT SEISMIC RESTRAINT REQUIREMENTS. WATER HEATERS SHALL BE ANCHORED OR STRAPPED TO RESIST HORIZONTAL DISPLACEMENT DUE TO EARTHQUAKE MOTION, STRAPPING SHALL BE AT POINTS WITHIN THE UPPER ONE-THIRD AND LOWER ONETHIRD OF ITS VERTICAL DIMENSIONS. AT THE LOWER POINT, A DISTANCE OF NOT LESS THAN FOUR INCHES SHALL BE MAINTAINED ABOVE THE CONTROLS WITH STRAPPING. ALL COUNTERTOP AND WALL MOUNTED PLUMBING FIXTURES (URINALS, LAVATORIES, COUNTERTOP MOUNTED SINKS, DRINKING FOUNTAINS, ETC.) SHALL BE PROVIDED WITH A T-PATTERN WALL CLEANOUT BELOW PLUMBING FIXTURE. CLEANOUT SHALL BE CAST IRON DRAINAGE T-PATTERN, 90 DEGREE BRANCH FITTINGS WITH SQUARE HEAD BRASS SCREW PLUGS OF THE SAME SIZE AS THE PIPE UP TO AND INCLUDING 4 INCHES, PER SPECIFICATION 22 1300. WALL CLEANOUTS IN FINISHED AREAS SHALL BE ZURN No. Z-1460-8 WITH POLISHED STAINLESS STEEL OR CHROME PLATED METAL COVER.
5 5.1
COTG
Z
Z
SHEET KEYNOTES Y.9
5
1. 2. 3. 4. 5.
3" SAN
4" ROOF DRAIN/OVERFLOW DRAIN LEADER FROM ABOVE. REFER TO CIVIL DRAWING FOR CONTINUATION. 4" ROOF DRAIN/OVERFLOW DRAIN LEADER DOWN IN WALL TO DOWN SPROUT NOZZLE. REFER TO GREASE INTERCEPTOR DETAIL A1/P502. REFER TO ISLAND VENT DETAIL C1/P502. 5
ARCHITECT AT
E O F T EX
A S
ST
Y.9
ABBAS SHIRIAN D
Y
D2
LEVEL 1 WASTE & VENT PLAN - AREA C ALT SCALE: 1/8" = 1'-0"
0'
Abbas 2016.02.15 13:26:04-07'00'
SAN
NORTH 4" RD/ORD
4'
8'
16'
3
PROJECT
4" ORD 4" RD
4" ORD 4" RD
4" DN1
EE
IN
OF
D
R
102840 I C E N S E E SS G IO N A L E N
L
CLASSROOM 148
PR
CLASSROOM 149
5 RD ORD
4" RD/ORD
RD ORD
1
3" SAN
CLASSROOM 147 SAN
CLASSROOM 146
5 3" SAN
W.2 W.1
GIRLS 145
FD1
CORRIDOR 138
W 2 P402
P1a
P1
P1
P1
P3
P3
P3
STOR 137A
ELEC 150
P1a
P3
FC-02 FC-01
4" SAN
3/4" CD
4" RD/ORD CD
U
P2a
CORRIDOR 138
P2
VEST 142 4" VTR
3/4" CD
CD RD ORD
4" RD/ORD
RD ORD
1
4" ORD 4" RD
4" RD 4" ORD
4" DN1
P1a P2
~~
V
P3
P9
~
FD1
3 P402
P10
4" SAN
~
C
FD1
3
200 Longhorn Street Vega, TX 79092
VEGA ISD HIGH SCHOOL
X
SPEC ED 137 CLASSROOM 136 SAN
5
T P17
LAB 135
P18 5
V
2" SAN
S
P18 5
B
P12
V
P18
V
4" SAN 2" SAN
5
CLASSROOM 134 V
2" V
5
V
5
P18
V
P18
V
V
R
Addendum 004
P18 T
5 V
V 2" V
MECH 154
4 P402
P
STOR/PREP 133
4" RD
4" RD/ORD
V
Q
REVISIONS
P4
4" ORD
3"FS1
CORRIDOR 138
5
4" SAN
P4
V
V
V
P18
V
V
5
V
M
SAN
2" V 4" VTR 3" SAN P18
L
5
KEY PLAN - NTS
2" V
P18
WCO
4" SAN P18
5
P12
~
DCOTG
2
1
V
3
V
4" RD/ORD
SAN
~
V
4" DN1
RD ORD
T
N
4" SAN 4" SAN
P18
4
5
5
LAB 131
G1
A
CLASSROOM 132
02.15.2016
A3 / PL101B
14-0424.002
DRAWING NAME
MATCH LINE
LEVEL 1 WASTE & VENT PLAN AREA C
AREA B AREA A
3" GW NORTH
A3
LEVEL 1 WASTE & VENT PLAN - AREA C SCALE: 1/8" = 1'-0"
0'
3.1 4
5
4'
8'
16'
NORTH
INE CH L MAT
2/15/2016 1:03:02 PM
AS
PROJECT NO:
P18
~
3
REVIEWED BY DATE
A3 / PL101B
2
SP
2" SAN
J
1
DRAWN BY
AREA C
P17
3" GW
ADDENDUM #04
4" ORD 4" RD
2" SAN
RD ORD
02/15/16
SHEET NO.
PL101C 6
1
2
3
4
5
6
GENERAL SHEET NOTES A. B.
C.
D. E. F.
G.
E
H.
R1.8
R2
XXXX. ALL HOT AND COLD WATER DROPS/RISES TO FIXTURES SHALL BEVERTICAL BETWEEN THE FRAMING STUDS. ALL WASTE, VENT, AND WATER PIPING IN PIPE CHASE SHALL BE RACKED TIGHT TO INTERIOR FRAME WALL, LEAVING CENTER OF CHASE CLEAR FOR MAINTENANCE. ANY CROSSOVER SHALL BE 7'-0 A.F.F. TO BOTTOM OF PIPE MINIMUM. PROVIDE BALL VALVES FOR ALL WATER ISOLATION AND SUPPLY TAKE-OFFS. ISOLATION VALVES FOR BRANCH PIPING TO BE LOCATED ABOVE LAYIN CEILING FOR EASY ACCESS BY MAINTENANCE. ISOLATION VALVES THAT CAN NOT BE LOCATED ABOVE LAY-IN CEILING MUST BE PROVIDED MAINTENANCE ACCESS IN THE FORM OF AN ACCESSIBLE PLUMBING CHASE OR AN ACCESS PANEL. ALL EQUIPMENT DRAINS AND SHOCK ABSORBERS SHALL HAVE MAINTENANCE ACCESS IN THE FORM OF AN ACCESSIBLE PLUMBING CHASE OR AN ACCESS PANEL. FLOOR DRAINS SHALL BE INSTALLED WITH NICKEL BRONZE AND HEEL PROOF GRATES. COORDINATE ALL VTR'S WITH MECHANICAL FRESH AIR INTAKES ON ROOF. VENTS SHALL MAINTAIN A MINIMUM OF 12'-0" CLEARANCE. SEE SPECIFICATION SECTION 23 0548, SEISMIC RESTRAINT AND VIBRATION ISOLATION, FOR PROJECT SEISMIC RESTRAINT REQUIREMENTS. WATER HEATERS SHALL BE ANCHORED OR STRAPPED TO RESIST HORIZONTAL DISPLACEMENT DUE TO EARTHQUAKE MOTION, STRAPPING SHALL BE AT POINTS WITHIN THE UPPER ONE-THIRD AND LOWER ONETHIRD OF ITS VERTICAL DIMENSIONS. AT THE LOWER POINT, A DISTANCE OF NOT LESS THAN FOUR INCHES SHALL BE MAINTAINED ABOVE THE CONTROLS WITH STRAPPING. ALL COUNTERTOP AND WALL MOUNTED PLUMBING FIXTURES (URINALS, LAVATORIES, COUNTERTOP MOUNTED SINKS, DRINKING FOUNTAINS, ETC.) SHALL BE PROVIDED WITH A T-PATTERN WALL CLEANOUT BELOW PLUMBING FIXTURE. CLEANOUT SHALL BE CAST IRON DRAINAGE T-PATTERN, 90 DEGREE BRANCH FITTINGS WITH SQUARE HEAD BRASS SCREW PLUGS OF THE SAME SIZE AS THE PIPE UP TO AND INCLUDING 4 INCHES, PER SPECIFICATION 22 1300. WALL CLEANOUTS IN FINISHED AREAS SHALL BE ZURN No. Z-1460-8 WITH POLISHED STAINLESS STEEL OR CHROME PLATED METAL COVER.
R2.1
SHEET KEYNOTES
5.
ARCHITECT
BLEACHER
E O F T EX
D
OF
L
RU
EE
R
102840 I C E N S E E SS G IO N A L E N
IN
200B
D
Abbas 2016.02.15 13:25:55-07'00'
RV PROJECT
5
RT
XRB
A
ABBAS SHIRIAN PR
XRB
AT
S
RV
ROUTE PIPING HIGH IN CEILING SPACE. CONDENSATE DRAIN FROM ROOF TOP UNIT SHALL DRAIN ON ROOF IN CODE COMPLIANT MANNER. SEE DETAIL B3/P501 FOR DOUBLE CLEANOUT TO GRADE. PROVIDE GAS REGULATOR ASSEMBLY AT UNIT WITH AN INLET OF 2 PSI AND OUTLET PRESSURE OF 14" W.C., GAS SHUT-OFF VALVE, DIRTLEG AND UNION AT GAS FIRED EQUIPMENT. REFER TO CIVIL DRAWING FOR CONTINUATION.
ST
1. 2. 3. 4.
~
RS ~
SAN
3
DCW
DCOTG
1/2" DCW
RU
RR
RS
DCW
1/2" DCW
IN GYM CEILING SPACE
P10
RQ
1 2" VTR
RP
GYMNASIUM B100
RR STAIR 2
RQ
169
WEIGHT ROOM
TRACK
A155
156
C
RN
GYMNASIUM
~
RP
G
G
IN GYM CEILING SPACE
1 1/4" G
B100
1 G
STAIR 2
STOR
169
B138
RTU-27 150 CFH
1 1/2" G ON ROOF
2
RN
RK
4
200 Longhorn Street Vega, TX 79092
RT
VEGA ISD HIGH SCHOOL
2" SAN
RM RK RJ RG HALL
RF
B140
B
RJ RG RE RF
Addendum 004
RD
REVISIONS 5
RE
R2.1
RD
02/15/16
ADDENDUM #04
KEY PLAN - NTS
R2
RB RA
AREA C
EXISTING
DRAWN BY
SP
REVIEWED BY
AS
DATE
RB
LEVEL 1 ABOVE
PROJECT NO:
14-0424.002
DRAWING NAME
MATCH LINE
RA
A
02.15.2016
WASTE & VENT PLAN - AREA A ALTERNATE
AREA B AREA A
5
NORTH
A1
LOWER LEVEL WASTE & VENT PLAN - AREA A ALT SCALE: 1/8" = 1'-0"
1
0'
2
4'
8'
A3
16'
3
LEVEL 1 WASTE & VENT PLAN - AREA A ALT 0'
SCALE: 1/8" = 1'-0"
4
5
4'
8'
16'
NORTH
E NE H LLIIN CH ATTC M MA
2/15/2016 1:03:04 PM
NORTH
SHEET NO.
PL102A 6
1
2
3
4
5
6
GENERAL SHEET NOTES 1.9
2
3
4
A. B.
5.1
5
C.
1
D. E. F.
Z
G. 1 1/4" G
CAP
Y.9
2" G
H. RTU-02 80 CFH
1
2
RTU-03 80 CFH
1
2
1 1/4" G
Y 4" RD/ORD 1,915 SQ/FT
X
4" RD/ORD 2,320 SQ/FT
1 1/4" G
2" G RTU-04 80 CFH
W.2
1
2
1" G
2
SHEET KEYNOTES
1 1/4" G
CU-01
1.
V
1
2
CU-02
U
4" RD/ORD 1,360 SQ/FT
ARCHITECT
4" RD/ORD 1,920 SQ/FT
2
Abbas 2016.02.15 13:25:44-07'00'
RTU-08 80 CFH
EF-08 1 1/4" G
S
1
PROJECT
2
RTU-09 80 CFH
R 1 1/4" G
Q
1
2
1 1/4" G
N
RTU-11 80 CFH
GAS PIPE 4" G DROP DOWN TO DWH-1/DWH-2
L
2
4" RD/ORD 2,322 SQ/FT
1 1/4" G
M
1
1
VEGA ISD HIGH SCHOOL
2" G
2
1 1/4" G
EF-07
RTU-12 80 CFH
1
2
1
2
1
2
J 2" G GAS PIPE DROP DOWN TO KITCHEN EQUIPMENTS
RTU-15 G
1" G
60 CFH
3/4" G
4" RD/ORD
4" RD/ORD
RTU-16 120 CFH
1 1/4" G
G.9 R2.1
1
KEF-02
2
4" G
2
RTU-24 200 CFH
RTU-19 200 CFH
2 1/2" G
4" G 1 1/2" G
4" RD/ORD
CU-03
4" RD/ORD
6" G G 6" G
4" G
4
6" G
D.2
2" G
D
RTU-26A 350 CFH
4" RD/ORD G
1
E 6" G
6" GAS PIPE UP ALONG WALL TO ROOF
CU-04
2
3
1
1 1/4" G
CU-05
4" RD/ORD
RTU-20 120 CFH
RTU-23A 600 CFH
RT
1
2
2 3" G
1 1 1/2" G
1 1/4" G 3" G
RS
B
RTU-18 130 CFH
2
5
5
RU
F
RTU-25 200 CFH 1
5
XRB
CU-07
G
EF-03
4" RD/ORD
RV
4" RD/ORD 2,484 SQ/FT
EF-05
1 1/2" G 5
1 1/2" G 6" G
2" G 3" G
2
5
2 5
1
1 1/2" G
1
1 1/4" G G
2
RTU-14 150 CFH
G
1
1 1/4" G
1
5
RTU-17 80 CFH
2
G
R1.8
R2
G
5
MAU-01 105 CFH 1
~
G
H
RTU-13 80 CFH
200 Longhorn Street Vega, TX 79092
RTU-10 80 CFH
3" G
4" RD/ORD 2,816 SQ/FT
G
P
C
102840
OF
T
1
A
I C E N S E E SS G IO N A L E N
L
1" G
E O F T EX
ABBAS SHIRIAN PR
D
RTU-07 60 CFH
AT
S
2. 3. 4. 5.
PROVIDE GAS REGULATOR ASSEMBLY AT EACH UNITS WITH AN INLET OF 2 PSI AND OUTLET PRESSURE OF 14" W.C., GAS SHUT-OFF VALVE, DIRTLEG AND UNION AT GAS FIRED EQUIPMENT. CONDENSATE DRAIN FROM ROOF TOP UNIT SHALL DRAIN ON ROOF IN CODE COMPLIANT MANNER. CONNECT NEW 6" GAS PIPING TO EXISTING 8" @ 2 PSI OR LARGER ON ROOF. EXISTING GAS METER/REGULATOR SHALL SIZE FOR ADDITIONAL LOAD OF 5200 CFH. 4" RD/ORD DOWN ALONG WALL TO DOWNSPOUT NOZZLE.
R
RTU-06 80 CFH
5
D
EF-01
W
1
EE
W.1
IN
RTU-05 60 CFH
ST
E
ALL HOT AND COLD WATER DROPS/RISES TO FIXTURES SHALL BEVERTICAL BETWEEN THE FRAMING STUDS. ALL WASTE, VENT, AND WATER PIPING IN PIPE CHASE SHALL BE RACKED TIGHT TO INTERIOR FRAME WALL, LEAVING CENTER OF CHASE CLEAR FOR MAINTENANCE. ANY CROSSOVER SHALL BE 7'-0 A.F.F. TO BOTTOM OF PIPE MINIMUM. PROVIDE BALL VALVES FOR ALL WATER ISOLATION AND SUPPLY TAKE-OFFS. ISOLATION VALVES FOR BRANCH PIPING TO BE LOCATED ABOVE LAYIN CEILING FOR EASY ACCESS BY MAINTENANCE. ISOLATION VALVES THAT CAN NOT BE LOCATED ABOVE LAY-IN CEILING MUST BE PROVIDED MAINTENANCE ACCESS IN THE FORM OF AN ACCESSIBLE PLUMBING CHASE OR AN ACCESS PANEL. ALL EQUIPMENT DRAINS AND SHOCK ABSORBERS SHALL HAVE MAINTENANCE ACCESS IN THE FORM OF AN ACCESSIBLE PLUMBING CHASE OR AN ACCESS PANEL. FLOOR DRAINS SHALL BE INSTALLED WITH NICKEL BRONZE AND HEEL PROOF GRATES. COORDINATE ALL VTR'S WITH MECHANICAL FRESH AIR INTAKES ON ROOF. VENTS SHALL MAINTAIN A MINIMUM OF 12'-0" CLEARANCE. SEE SPECIFICATION SECTION 23 0548, SEISMIC RESTRAINT AND VIBRATION ISOLATION, FOR PROJECT SEISMIC RESTRAINT REQUIREMENTS. WATER HEATERS SHALL BE ANCHORED OR STRAPPED TO RESIST HORIZONTAL DISPLACEMENT DUE TO EARTHQUAKE MOTION, STRAPPING SHALL BE AT POINTS WITHIN THE UPPER ONE-THIRD AND LOWER ONETHIRD OF ITS VERTICAL DIMENSIONS. AT THE LOWER POINT, A DISTANCE OF NOT LESS THAN FOUR INCHES SHALL BE MAINTAINED ABOVE THE CONTROLS WITH STRAPPING. ALL COUNTERTOP AND WALL MOUNTED PLUMBING FIXTURES (URINALS, LAVATORIES, COUNTERTOP MOUNTED SINKS, DRINKING FOUNTAINS, ETC.) SHALL BE PROVIDED WITH A T-PATTERN WALL CLEANOUT BELOW PLUMBING FIXTURE. CLEANOUT SHALL BE CAST IRON DRAINAGE T-PATTERN, 90 DEGREE BRANCH FITTINGS WITH SQUARE HEAD BRASS SCREW PLUGS OF THE SAME SIZE AS THE PIPE UP TO AND INCLUDING 4 INCHES, PER SPECIFICATION 22 1300. WALL CLEANOUTS IN FINISHED AREAS SHALL BE ZURN No. Z-1460-8 WITH POLISHED STAINLESS STEEL OR CHROME PLATED METAL COVER.
CU-06
3" G
5
RTU-21 80 CFH
G
RR RQ
1 1/4" G
2 1/2" G
1-1/4"" GAS PIPE UP ALONG WALL TO ROOF
2
EF-04
2 RTU-23B 600 CFH
1
C
1
4" RD/ORD
RP
Addendum 004
RTU-22 4" RD/ORD 1 1/4" G
RN
1
IN GYM CEILING SPACE
RM
150 CFH
2
RTU-26B 350 CFH
REVISIONS
1
2
B
EF-09
A
1 1/4" G
4
02/05/16
ADDENDUM #02
5
02/15/16
ADDENDUM #04
KEY PLAN - NTS
RK 5
6.5 7
RJ 5
RG
5 4" RD/ORD
5
5
RF
4" RD/ORD
R2.9
5
RE
4" RD/ORD
A
R3 20
R5 R6
R7
R8
R8.1
8
9
10 11 13 14 15 16
8.8 R9 AREA C
DRAWN BY
SP
REVIEWED BY
AS
EXISTING DATE LEVEL 1 ABOVE
02.15.2016
PROJECT NO:
14-0424.002
DRAWING NAME
MATCH LINE
ROOF PLUMBING PLAN
RD RB AREA B
NORTH
A1
AREA A
ROOF PLUMBING PLAN SCALE: 1/16" = 1'-0"
0'
1
2
3
4
5
4'
8'
16'
NORTH
INE CH L MAT
2/15/2016 1:03:07 PM
RA
SHEET NO.
PL141 6
1
2
3
4
5
6
GENERAL SHEET NOTES A. B.
C.
D. E. F.
P17 2" DCW
~
A3 / PP101C
~
~ ~ ~
A3 / PP101C
1" DHW
~ 1" DHW 2" DHW
DHW DHW DHW
CLASSROOM 129 3/4" DCW
1/2" DCW
RR 130A
P8
DCW
FD1
DHW
DCW P1a
DCW DHW DHW
G.9
2" DHW
STOR 125A
1" DHW 120 DWH 140 DWH
1/2" 2 DHW 1/2" DCW
SHEET KEYNOTES
1/2" DCW
1. 2.
P4
ROUTE PIPING HIGH IN CEILING SPACE. PROVIDE GAS SHUT-OFF VALVE, DIRTLEG AND UNION AT GAS FIRED EQUIPMENT.
ARCHITECT AT
1" DHWR
MEDIA CENTER 125
102840
OF
I C E N S E E SS G IO N A L E N
L
RS
ART 123
D
A
ABBAS SHIRIAN
RT
PR
DHW
1
E O F T EX
S
P6
Abbas 2016.02.15 13:25:34-07'00'
DCW
DHW
DCW
H
P5
DHWR
WARMING KITCHEN 128
P5
2
DHW
DHW
5
2" DHW 2" DHW
G
2448
2448
3/4" G
R
DHW
P4
DCW DHW
2472
STOR 128B
G
2472
2472
G
STOR 129A
P7
P13
DHW
STOR 128A
DHW
P3
D
3/4" G
ST
P7
1" DHW
EE
P7
5
IN
1/2" DCW
DCW
G
DHW
1/2" DCW
1" DHWR DHWR
1/2" DCW
CLASSROOM 129
6 P403
H.
LIFESKILLS 130
P7
3/4" G P7
4 P403
DHW
2
2" DCW
G.
J
E
ALL HOT AND COLD WATER DROPS/RISES TO FIXTURES SHALL BEVERTICAL BETWEEN THE FRAMING STUDS. ALL WASTE, VENT, AND WATER PIPING IN PIPE CHASE SHALL BE RACKED TIGHT TO INTERIOR FRAME WALL, LEAVING CENTER OF CHASE CLEAR FOR MAINTENANCE. ANY CROSSOVER SHALL BE 7'-0 A.F.F. TO BOTTOM OF PIPE MINIMUM. PROVIDE BALL VALVES FOR ALL WATER ISOLATION AND SUPPLY TAKE-OFFS. ISOLATION VALVES FOR BRANCH PIPING TO BE LOCATED ABOVE LAYIN CEILING FOR EASY ACCESS BY MAINTENANCE. ISOLATION VALVES THAT CAN NOT BE LOCATED ABOVE LAY-IN CEILING MUST BE PROVIDED MAINTENANCE ACCESS IN THE FORM OF AN ACCESSIBLE PLUMBING CHASE OR AN ACCESS PANEL. ALL EQUIPMENT DRAINS AND SHOCK ABSORBERS SHALL HAVE MAINTENANCE ACCESS IN THE FORM OF AN ACCESSIBLE PLUMBING CHASE OR AN ACCESS PANEL. FLOOR DRAINS SHALL BE INSTALLED WITH NICKEL BRONZE AND HEEL PROOF GRATES. COORDINATE ALL VTR'S WITH MECHANICAL FRESH AIR INTAKES ON ROOF. VENTS SHALL MAINTAIN A MINIMUM OF 12'-0" CLEARANCE. SEE SPECIFICATION SECTION 23 0548, SEISMIC RESTRAINT AND VIBRATION ISOLATION, FOR PROJECT SEISMIC RESTRAINT REQUIREMENTS. WATER HEATERS SHALL BE ANCHORED OR STRAPPED TO RESIST HORIZONTAL DISPLACEMENT DUE TO EARTHQUAKE MOTION, STRAPPING SHALL BE AT POINTS WITHIN THE UPPER ONE-THIRD AND LOWER ONETHIRD OF ITS VERTICAL DIMENSIONS. AT THE LOWER POINT, A DISTANCE OF NOT LESS THAN FOUR INCHES SHALL BE MAINTAINED ABOVE THE CONTROLS WITH STRAPPING. ALL COUNTERTOP AND WALL MOUNTED PLUMBING FIXTURES (URINALS, LAVATORIES, COUNTERTOP MOUNTED SINKS, DRINKING FOUNTAINS, ETC.) SHALL BE PROVIDED WITH A T-PATTERN WALL CLEANOUT BELOW PLUMBING FIXTURE. CLEANOUT SHALL BE CAST IRON DRAINAGE T-PATTERN, 90 DEGREE BRANCH FITTINGS WITH SQUARE HEAD BRASS SCREW PLUGS OF THE SAME SIZE AS THE PIPE UP TO AND INCLUDING 4 INCHES, PER SPECIFICATION 22 1300. WALL CLEANOUTS IN FINISHED AREAS SHALL BE ZURN No. Z-1460-8 WITH POLISHED STAINLESS STEEL OR CHROME PLATED METAL COVER.
A3 / PP101A
PROJECT
1" DHW
RR
2" DHW
2" DCW
1 3/4" DCW
COMPUTER LAB 121
F
P3 P1
5 P403
P3
P1
E
P1 P2
FD1
P1 P3
1 3" DCW
P3
P2
DHW
DCW
P2
P3
DCW
P1
FD1
12
P1
DHW
P2 ~
BOYS ~ 118
GIRLS 119
~
~
P10
D
P3
RN
DWC/DWH/DWR DOWN TO BASEMENT
1" DHW
DHW
STUDENT COMMONS 102
D.2
3" DCW
DCW
2" DHW 1
C
RP
CORRIDOR A132
ELEV 721
RM
CLASSROOM 122
FD1 FAM RR P1a 116
2" DCW 1" DHW 1" DHW
STAGE A124
DHW
OFFICE 115
RK 1
RC RC
W 122A
DCW
DHW
TEST STOR 115A
STOR 122C
M 122B P1a
P3
7 P403
P1a
STAIR 1 713
CORRIDOR 104
P3
200 Longhorn Street Vega, TX 79092
P1a
2" DCW 1" DHW 2" DHW 1
KILN 123B
VEGA ISD HIGH SCHOOL
P1a
P9
RQ
STOR 123A
P3 P1a
CONF 103A
P1a
P3
FILES 113
M 112 ~~
W 108
2" DCW
RJ
STOR 111
RG
~~
DCW DHW
C
DHW
CORRIDOR 106
RF
1" DHW
RECEPTION 103
DCW DHW
DHW
B
1" DHW
ISS 107
WORKROOM 109 PROP STOR A125
CORRIDOR 110
1/2" DCW
RE
P4
1" DHW
Addendum 004
RD
DCW
1" DHW 1/2" DCW
DHW DHW
1
B
LOUNGE 109A
PRINC 105
REVISIONS
A
VEST 101
4
02/05/16
ADDENDUM #02
5
02/15/16
ADDENDUM #04
KEY PLAN - NTS STOR 164
R9 R7
R8
R8.1 910
20
R2.9
A
R3
R5
11
AREA C
DRAWN BY
SP
REVIEWED BY
AS
EXISTING DATE
02.15.2016
PROJECT NO:
R6
14-0424.002
DRAWING NAME
MATCH LINE
LEVEL 1 PRESSURE PIPING PLAN AREA B
AREA B AREA A
A3
1
2
3
LEVEL 1 PRESSURE PIPING PLAN - AREA B SCALE: 1/8" = 1'-0"
0'
4
5
4'
8'
16'
NORTH
INE CH L MAT
2/15/2016 1:03:10 PM
NORTH
SHEET NO.
PP101B 6
1
2
3
4
5
6
GENERAL SHEET NOTES 1.9
2
3
4
5
A. B.
5.1
C.
D. E. F.
G.
E
VEST H.
A153
CLASSROOM
CLASSROOM
A151
A150
0.5
STOR
CORRIDOR
STOR
A151A
A152
A150A
Z
1
1.9
2
3
4
ALL HOT AND COLD WATER DROPS/RISES TO FIXTURES SHALL BEVERTICAL BETWEEN THE FRAMING STUDS. ALL WASTE, VENT, AND WATER PIPING IN PIPE CHASE SHALL BE RACKED TIGHT TO INTERIOR FRAME WALL, LEAVING CENTER OF CHASE CLEAR FOR MAINTENANCE. ANY CROSSOVER SHALL BE 7'-0 A.F.F. TO BOTTOM OF PIPE MINIMUM. PROVIDE BALL VALVES FOR ALL WATER ISOLATION AND SUPPLY TAKE-OFFS. ISOLATION VALVES FOR BRANCH PIPING TO BE LOCATED ABOVE LAYIN CEILING FOR EASY ACCESS BY MAINTENANCE. ISOLATION VALVES THAT CAN NOT BE LOCATED ABOVE LAY-IN CEILING MUST BE PROVIDED MAINTENANCE ACCESS IN THE FORM OF AN ACCESSIBLE PLUMBING CHASE OR AN ACCESS PANEL. ALL EQUIPMENT DRAINS AND SHOCK ABSORBERS SHALL HAVE MAINTENANCE ACCESS IN THE FORM OF AN ACCESSIBLE PLUMBING CHASE OR AN ACCESS PANEL. FLOOR DRAINS SHALL BE INSTALLED WITH NICKEL BRONZE AND HEEL PROOF GRATES. COORDINATE ALL VTR'S WITH MECHANICAL FRESH AIR INTAKES ON ROOF. VENTS SHALL MAINTAIN A MINIMUM OF 12'-0" CLEARANCE. SEE SPECIFICATION SECTION 23 0548, SEISMIC RESTRAINT AND VIBRATION ISOLATION, FOR PROJECT SEISMIC RESTRAINT REQUIREMENTS. WATER HEATERS SHALL BE ANCHORED OR STRAPPED TO RESIST HORIZONTAL DISPLACEMENT DUE TO EARTHQUAKE MOTION, STRAPPING SHALL BE AT POINTS WITHIN THE UPPER ONE-THIRD AND LOWER ONETHIRD OF ITS VERTICAL DIMENSIONS. AT THE LOWER POINT, A DISTANCE OF NOT LESS THAN FOUR INCHES SHALL BE MAINTAINED ABOVE THE CONTROLS WITH STRAPPING. ALL COUNTERTOP AND WALL MOUNTED PLUMBING FIXTURES (URINALS, LAVATORIES, COUNTERTOP MOUNTED SINKS, DRINKING FOUNTAINS, ETC.) SHALL BE PROVIDED WITH A T-PATTERN WALL CLEANOUT BELOW PLUMBING FIXTURE. CLEANOUT SHALL BE CAST IRON DRAINAGE T-PATTERN, 90 DEGREE BRANCH FITTINGS WITH SQUARE HEAD BRASS SCREW PLUGS OF THE SAME SIZE AS THE PIPE UP TO AND INCLUDING 4 INCHES, PER SPECIFICATION 22 1300. WALL CLEANOUTS IN FINISHED AREAS SHALL BE ZURN No. Z-1460-8 WITH POLISHED STAINLESS STEEL OR CHROME PLATED METAL COVER.
5 5.1
Z
SHEET KEYNOTES Y.9
OF
Abbas 2016.02.15 13:25:24-07'00'
NORTH
LEVEL 1 PRESSURE PIPING PLAN - AREA C ALT 4'
8'
16' P16
STOR 148A
PROJECT
P16
DHW
0'
5
STOR 149A
DCW DHW
SCALE: 1/8" = 1'-0"
R
102840
Y
D2
A
I C E N S E E SS G IO N A L E N
L
D
E O F T EX
ABBAS SHIRIAN PR
CLASSROOM 148
CLASSROOM 149
AT
S
4. 5. 6.
ARCHITECT
D
3.
ROUTE PIPING ABOVE CEILING. 1-1/4" DCW & DHW TO EMERGENCY EYE WASH/SHOWER MIXING VALVE. PROVIDE 1-1/4" FROM MIXING VALVE TO EMERGENCY EYE WASH/SHOWER. GAS PIPING BELOW SLAB SHALL BE JOINTLESS PE COATED CSST. ENCASE BOTH SERVICES IN FLEXIBLE PE SLEEVE. TERMINATE SLEEVE 6" A.F.F. BOTH SIDES. ROUTE PIPING BELOW FLOOR. REFER TO LAB EQUIPMENT SUPPLIER FOR PIPIING CONNECTION AND REQUIREMENTS. COORDINATE LOCATION OF SECONDARY ELECTRICAL PANEL AND REMOTE PANIC PANEL WITH ARCHITECT PRIOR TO INSTALLATION. REFER TO DETAIL D1/P502.
EE
1. 2.
CLASSROOM 148
IN
CLASSROOM 149
ST
Y.9
DCW
STOR 147A
DCW
1
STOR 146A
3/4" DCW
3/4" DCW
CLASSROOM 146
DHW
DCW
DHW
1" DCW 2" DHW 2" DHW
VEGA ISD HIGH SCHOOL
CLASSROOM 147
W.2 GIRLS 145 P1a
2 P403
P1
P1
P1
P3
P3
~ ~ ~
CORRIDOR 138
W
C
~ ~ ~
W.1
STAFF RR 143
BOYS 144
P10
P1a
V
3 P403
JAN 139
P3
P3
P2a P2
P2
P1a
P9 P3 2" DHW
IDF 141
VEST 142
DHW
STOR 137A
DCW
ELEC 150
DHW
U 1
SPEC ED 137
2" DHW 2" DCW
200 Longhorn Street Vega, TX 79092
X
LAB 135
1/2" DCW 1/2" DHW
DCW
T
DHW
CLASSROOM 136
P17
2" DHW 2" DHW
P18
1/2" G
3 1/2" G
DHW
MECH 154
P
DWH-2
3/4" DHW 3/4" DCW
120 DWH
G
STOR/PREP 133 DHWR DHW DCW DHW DHWR P4
DHW
~
T
5
L 5
3 1/2" G P18
1/2" G DHW
DCW
STOR 134A
1" DHW 2" DHW
5 2 4
P18
P12
G
CLASSROOM 132
2/15/2016 1:03:13 PM
02/15/16
ADDENDUM #04
REVIEWED BY
AS 02.15.2016
PROJECT NO:
LEVEL 1 PRESSURE PIPING PLAN AREA C
120 DWH
A3 / PP101B
AREA B
~ ~ ~ AREA A
3.1
LEVEL 1 PRESSURE PIPING PLAN - AREA C SCALE: 1/8" = 1'-0"
0'
5
4'
8'
16'
NORTH
14-0424.002
DRAWING NAME
MATCH LINE
4
SP
DATE
140 DWH
P17 2" DCW
DRAWN BY
AREA C
INE CH L MAT
3
5
KEY PLAN - NTS
1" DHWR
NORTH
2
ADDENDUM #02
STOR 132A
1
~ ~
1
02/05/16
5
A3 / PP101B
A3
4
1" DHW 2" DCW
5
J
REVISIONS
P20 6
A 1/2" DHW 1/2" DCW
Addendum 004
2" DHW 2" DHW
140 DWH
2" DHW 1" DHWR
3 1/2" G 1/2" DHW 1/2" G 1/2" DCW P19 P18 P18a P18 DCW LAB DHW G 131 1/2" G 1/2" DHW 5 1/2" DCW 3 DCW P18 G DHW
M
5
P20 6
1" DCW
DWH-1
N
P19 P18a 5 3 1/2" G
P4 ~ ~ ~~ ~
Q
CLASSROOM 134
DCW
G 1" DHWR 2" DHW
~
8 P402
P18
1/2" G T
P12
5
DHW
P18 1/2" DCW 1/2" DHW
2
DHW DHW DHWR
R
DCW
DCW
1/2" G G
1/2" DCW 1/2" DHW
4
DHW
5
G DHW
P18
3
P18
DCW
B
G
DHW
5
DHW
DCW
DCW
DHW
S
DHW DCW
5
SHEET NO.
PP101C 6
1
2
3
4
5
6
1
1
5
5
5
5
OAKUM
A
2 LINK-SEAL
1
5
1 2
4
E
1
2 FLOW
_" MIN.
6" MIN.
2
3 3 2
6
5
3
4
A
2
FLOW EXTERIOR ELEVATION 3
SECTION 'A'
6
3
MECHANICAL JOINT FROM SUPPLY PIPE TO STAINLESS STEEL, CONTINUE INTO BUILDING WITH STAINLESS STEEL.
5
PIPE SLEEVE, SEE SPECIFICATIONS
6
MEGALUG PIPE RESTRAINT HARNESS
1
2
3
D1
D2
SCALE: NONE
4
DUCTILE, CAST-IRON, OR PVC WATER
FOR PIPE MATERIAL, SEE SPECIFICATIONS.
2
PIPE SLEEVE, SEE SPECIFICATIONS FOR MATERIALS, LENGTH OF SLEEVE AS REQUIRED.
CONCRETE THRUST BLOCK SIZED IN ACCORDANCE WITH UBC IF REQUIRED BY
5
PIPE SLEEVE, SEE SPECIFICATIONS
6
MEGALUG PIPE RESTRAINT HARNESS
MECHANICAL JOINT FROM SUPPLY PIPE TO STAINLESS STEEL, CONTINUE INTO BUILDING WITH STAINLESS STEEL
WATER ENTRY BELOW FOOTING
3/4" - 1"
1 1/2" 2"
1 1/2"
2 1/2"
2" - 2 1/2"
4"
3" - 4"
6"
6"
10"
4
EXTERIOR WALL PENETRATION
D3
SCALE: NONE
1 1/4"
1 1/4"
SEE STRUCTURAL DRAWINGS FOR CONSTRUCTION OF WALL.
3
1/2"
D4
SCALE: NONE
1
NATURAL GAS CARRIER LINE
2
FINISH GRADE
3
CONCRETE SLAB OR PAVING
4
SCOTCHRAP TAPE #51 (20 MIL.)
ARCHITECT
HARDSCAPE PENETRATION SCALE: NONE
PR
102840
OF
5
A
I C E N S E E SS G IO N A L E N
L
7
E O F T EX
ABBAS SHIRIAN
D 6
AT
S
WATER ENTRY THRU FOOTING
AMES IN-BUILDING RISER. STAINLESS STEEL TYPE 304. SEE PLANS FOR SIZE AND
1
R
DUCTILE, CAST-IRON, OR PVC WATER SERVICE.
CONCRETE THRUST BLOCK SIZED IN ACCORDANCE WITH UBC IF REQUIRED BY AHJ
D
2
4
EE
AMES IN-BUILDING RISER. STAINLESS STEEL TYPE 304. SEE PLANS FOR SIZE AND SERVICE
IN
1
MIN. PIPE SLEEVE (ID)
ST
PIPE SIZE
Abbas 2016.02.15 13:25:17-07'00'
10 PROJECT
7 4
5
8
5
6
4
2
2
4
ADJUSTABLE FLOOR CLEANOUT WITH INTERNAL BRONZE THREADED PLUG AND SCORIATED COVER SECURED TO PLUG WITH COUNTERSUNK SCREW
4
FINISHED WALL
1
9
9
9 12"-18"
FLOW
10
1
CAULK AS REQUIRED
10
CLEANOUT TEE
FLOW
5
BALANCE OF PIPING SAME AS CLEANOUT TO GRADE 1
C 2
3
4
WALL CLEANOUT
B1
FINISHED FLOOR
3
STAINLESS STEEL ACCESS COVER W/ COUNTERSUNK SCREW
CLEANOUT PLUG W/LINK SEAL
VEGA ISD HIGH SCHOOL
8
B2
SCALE: NONE
SERVICE LINE, SEE SPECIFICATIONS FOR PIPE MATERIALS.
5
CLEANOUT WITH HEAVY DUTY SCORIATED SECURED TOP .
6
SAME SIZE AS SERVICE LINE, THRU 4" PIPE, MAXIMUM 4" SIZE REQUIRED. CAST IRON SOIL PIPE RISER AND FITTINGS. COMPACTED EARTH, SEE SPECIFICATIONS.
WYE FITTING 1
SERVICE LINE, SEE SPECIFICATIONS FOR PIPE MATERIALS.
2
SAME SIZE AS SERVICE LINE, THRU 4" PIPE, MAXIMUM 4" SIZE REQUIRED.
FINISH HARDSCAPE. SEE SITE PLAN DRAWINGS FOR ELEVATION.
7
18"X18"X4" THICK CONCRETE COLLAR.
8
1/8TH BEND.
9
WYE FITTING.
10
2" CHAMFER ON ALL COLLARS IN EARTH.
CLEANOUT TO GRADE
3
CAST IRON SOIL PIPE RISER AND FITTINGS.
4
COMPACTED EARTH, SEE SPECIFICATIONS.
CLEANOUT WITH HEAVY DUTY SCORIATED SECURED TOP .
6
2" CHAMFER ON ALL COLLARS IN EARTH.
7
FINISH HARDSCAPE. SEE SITE PLAN DRAWINGS FOR ELEVATION.
8
4" THICK CONCRETE PAD.
9
1/8TH BEND.
10
WYE FITTING.
LENGTH TO SUIT
FLOW
GROUTED PLUG IN WYE FITTING OR 1/8 BEND IF CLEANOUT OCCURS AT END OF LINE
DOUBLE CLEANOUT TO GRADE
B3
SCALE: NONE
5
B4
SCALE: NONE
FLOOR CLEANOUT SCALE: NONE
200 Longhorn Street Vega, TX 79092
TOP OF CLEANOUT TO BE FLUSH WITH FINISHED FLOOR
3
# 2"
1 6
DHW
# 2"
# 2"
# 1"
# 2"
DCW DCW
G DHW
4
1-1/4"
# 1"
9
## GPM
13 10 DHC
2 12
# 2"
DHC
B
7 6
# 2"
5 G
3
D
2
Addendum 004
# 1"
1
2
9
11
6" MIN.
## GPM REVISIONS
3
1
7 2 3
8
4
5
SAN 8
4
02/05/16
ADDENDUM #02
5
02/15/16
ADDENDUM #04
FINISH FLOOR
14
1
EXPANSION TANK P15
8
4" MIN. HOUSEKEEPING PAD
2
FULL SIZED T&P RELIEF VALVE INDIRECTLY DISCHARGED TO FLOOR SINK, 2X PIPE DIA.
9
CIRCUIT SETTER/BALANCING VALVE
10
PETE'S PLUGS (TYPICAL)
3
PLUG VALVE W/DIRT LEG
11
HEAT TRAP PER MFG. SPEC'S
DRAWN BY
SP
4
THERMOMETER (TYPICAL)
12
UNION (TYPICAL)
REVIEWED BY
AS
5
THERMOSTATIC MIXING VALVE (TMV)
13
COMBUSTION AIR INTAKE AND FLUE BY MECHANICAL
DATE
6
IN-LINE PUMP ILP-1 14
DOMESTIC WATER HEATER, SEE SPEC'S
7 7 4 1
2
A
3
FLOOR DRAIN WITH ADJUSTABLE STRAINER, DOUBLE DRAINAGE FLANGE AND WEEP HOLES. SEE FLOOR DRAIN SPECIFICATIONS
5
5
CLAMP TO 24"x24" AND WATERPROOFING MEMBRANE (NOT REQUIRED FOR SINGLE POUR CONSTRUCTION)
6
7
2/15/2016 1:02:49 PM
A1
6 5
FINISHED FLOOR SLOPED IN ACCORDANCE WITH ARCH. DRAWINGS. COORDINATE WITH STRUCTURAL SEE PLUMBING FLOOR PLANS FOR SIZING AND P-TRAP REQUIREMENTS
CONCRETE FLOOR OF TWO POUR 8
4
TRAP GUARD WATER SAVING DEVICE SIZED PER DRAIN (IF SPECIFIED)
FOUR BAND HEAVY DUTY CLAMP, SEE SPECIFICATIONS
1
FLOOR SINK GRATING, SEE FLOOR SINK SPECIFICATIONS
2
DOME STRAINER
3
FINISHED FLOOR
4
COMPACTED EARTH
5
SEE PLUMBING FLOOR PLANS FOR SIZING AND P-TRAP REQUIREMENTS
6
TRAP GUARD WATER SAVING DEVICE (SPECIFIED)
7
STRUCTURAL SLAB
7
5
CAULK AS REQUIRED ON INSTALLATION ABOVE GRADE
FLOOR DRAIN
A2
SCALE: NONE
FLOOR SINK
A3
SCALE: NONE
02.15.2016
PROJECT NO:
14-0424.002
DRAWING NAME
SEISMIC STRAPPING PER UPC 508.2 (IF REQUIRED)
PLUMBING DETAILS
NOTE: INSTALL THERMOSTATIC MIXING VALVE ASSEMBLY IN ACCORDANCE WITH MANUFACTURERS RECOMMENDATION. PROVIDE PIPING SCHEMATIC WITH SUBMITTALS
DOMESTIC WATER HEATER (DWH 1 AND 2) SCALE: NONE
SHEET NO.
P501 1
2
3
4
5
6
1
2
3
4
5
6
EXHAUST FAN ON ROOF
NOTES: A. HOOD FAN STAYS ON DURING EMERGENCY SHUTDOWN. B. EMERGENCY CONDITION PURGE FAN SHALL REMAIN ON OR BE STARTED DURING PURGE, POWER, GAS, AND WATER SHALL SHUTDOWN. C. REFER TO HVAC CONTROLS DIAGRAM FOR FAN OPERATION. D. AIR HANDLING UNIT SHALL SHUTDOWN UNDER EMERGENCY CONDITION VIA DDC. E. ALL CONTROL WIRING SHALL BE A MIN. OF 18 AWG. DIV 22 CONTRACTOR SHALL INCLUDE INSTALLATION OF CONTROLS WITH CONTROLS CONTRACTOR AND DIV. 26 CONTRACTOR FOR A COMPLETE AND WORKING SYSTEM.
CLASSROOM EXHAUST
CONTROL WIRING BY CONTROLS CONTRACTOR
WALL
UTILITY CONTROL GAS
E
GAS ISLAND SINK
ISLAND SINK
CONTROL WIRING BY CONTROLS CONTRACTOR
G
TO ELECTRICAL CONTACTOR ENCLOSURE.
PE SLEEVE
PE SLEEVE
CONTROL WIRING BY CONTROLS CONTRACTOR
G
GAS PIPING BELOW SLAB SHALL BE JOINTLESS PE COATED CSST. ENCASE BOTH SERVICES IN FLEXIBLE PE SLEEVE. TERMINATE SLEEVE 6" A.F.F. BOTH SIDES.
DCW DHW
GAS
D1
102840
OF
CONTROL WIRING BY CONTROLS CONTRACTOR
A
I C E N S E E SS G IO N A L E N
L
SCALE = NONE
D UTILITY CONTROLLER SURFACE MOUNTED. SEE FLOOR PLANS FOR LOCATIONS OF CONTROLLERS. CONTROLLERS SHALL BE FURNISHED AND INSTALLED BY DIV. 22. COORDINATE WITH DIV. 22, 23, & CONTROLS CONTRACTOR.
E O F T EX
ABBAS SHIRIAN
TYPICAL ISLAND SINK DETAIL PR
D5
120V BY DIV. 26.
AT
S
CLASSROOM SAFETY SHUTOFF BY DIV. 22. INSTALLED BY DIV. 22. COORDINATE WITH CONTROLS CONTRACTOR.
ARCHITECT
ST
NOTE A:
G
R
5
D
120V BY DIV. 26.
EE
COMMON
IN
TO DDC SYSTEM BY DIV 23.
6"
REFER TO FLOOR PLANS FOR CIRCUITS ROUTED THROUGH CONTACTORS WHICH WILL BE SHUTOFF IN EVENT OF AN EMERGENCY.
6"
LINE
ELECTRICAL PANEL ABOVE CEILING IN EACH SCIENCE CLASSROOM. SEE ELECTRICAL DRAWINGS
Abbas 2016.02.15 13:25:10-07'00'
CLASSROOM SAFETY SHUTOFF SOLENOID PANEL BY DIV 22. INSTALLED BY DIV. 22
PROJECT
SCIENCE ROOM CONTROL PANEL SCALE: 1/4" = 1'-0"
GAS TURRET WALL 6" MIN. SINK TOP BRACKET
WCO
2"
ACID NEUT TANK
2"
PLATED ROD
2"
1/2"
INSULATE INSIDE OF HOOD W/1" FIBERBOARD
5
ROLLER CHAIR SADDLE WASHER
6"
2" WCO V
C
2"
GALVANIZED CHANNEL
GALVANIZED 16 GA. SHEET METAL HOOD
SOLDIER CONT. ALL AROUND
SAN
SPRING STRUT NUT
1-5/8"
DCW 10" MIN.
G
NOTE A:
9"
CAULKED WATERTIGHT SLEEVE
DHW
4"
12"
ROUTE PIPING IN TRENCH
WATER PIPING BELOW FIRST FLOOR SLAB SHALL BE JOINTLESS, TYPE "L" SOFT TEMPER COPPER.
BASE FLASHING MATERIAL
2" ELEVATION
NOTE B:
NOTE: C:
C1
GAS PIPING BELOW FIRST FLOOR SLAB SHALL BE JOINTLESS PE COATED CSST. ENCASE BOTH SERVICES IN FLEXIBLE PE SLEEVE. TERMINATE SLEEVE 6" A.F.F. BOTH SIDES.
ROOF TOP PIPE SUPPORT DETAIL
C5
INSTALLATION AT SOME SINKS IS SIMILAR BUT NOT IDENTICAL.
ISLAND VENT
C2
SCALE: 1/4" = 1'-0"
END VIEW
SCALE = NONE
200 Longhorn Street Vega, TX 79092
VEGA ISD HIGH SCHOOL
5
PIPE THRU ROOF DETAIL SCALE = NONE
SPLIT RUBBER SEAL BUSHING
ALC OVERRIDE CONTROL CORD LENGTH TO SUIT
PUMP CORD PUMP 2
2" VENT
DOUBLE C.O.T.G.
4" INLET 4" OUTLET
B
EXTEND TO MATCH FINISH CONCRETE
SUMP PUMP CONTROL PANEL
8-10" PIPE CUTOUT CONCRETE FILL ON BOTH SIDES OF PIPE CUTOUT AND SLOPE TO CHANNEL WATER INTO PIPE.
SAMPLING VAULT
PLAN VIEW
SAMPLING VAULT
SHAFT WALL
SEALED LID
SANITARY SEWER SEE PLANS FOR ROUTING AND SIZE 5
OIL INTERCEPTOR. (GI-1) 4" INLET
(4)FLOATS TYP.
6" MIN. 4"
WATER LINE
COMPACTED OR UNDISTURBED SOIL
12"
12"
A SECTION VIEW
8-10" PIPE CUTOUT CONCRETE FILL ON BOTH SIDES OF PIPE CUTOUT AND SLOPE TO CHANNEL WATER INTO PIPE.
REINFORCING: TOP WALLS AND BOTTOM; No. 4 AT 8"O.C. BOTH WAYS, COMPARTMENT DIVIDERS; No. 3 AND 6"O.C. EACH WAY 1,000 GALLON LIQUID CAPACITY PRECAST CONCRETE INTERCEPTOR
ALC OPERATING AND ALTERNATING LEVEL CONTROL. CORD LENGTH TO SUIT. INSTALL CONTROLS THRU THROUGH SUMP COVER. SEALS WITH "O"-RING
STEEL BASIN COVER EPOXY COATED. SEALED TO BASIN WITH CAULKING COMPOUND
SUMP PUMP BASIN
SUMP PUMP COUPLING
BASIN
COUPLING 5
NEMA 1 DUPLEX CONTROL BOX
SUPPORT FOOTING
CONDUIT
02/05/16
ADDENDUM #02
5
02/15/16
ADDENDUM #04
VENT
CONDUIT BUSHING
ELEVATION V
2"VENT
SEE PLAN FOR ROUTING AND SIZING CHECK VALVE S
HINGED ACCESS DOOR WITH HASP
2"PUMPED DISCHARGE
REVIEWED BY
AS 02.15.2016 14-0424.002
DRAWING NAME
SEWAGE EJECTORS, SEE EQUIPMENT SPECIFICATIONS 6"MIN
PLAN
SP
PROJECT NO:
SUMP BASIN "O" RING SEAL INLET FLANGE FOR INLET PIPE
DRAWN BY
DATE
FLCA ALARM CONTROL
INLET
SUMP PUMP
SEE STRUCTURAL DRAWINGS FOR LOCATION
4
3" DISCHARGE
ELEVATION
SUMP PUMPS SEE PLUMBING SCHEDULE AND SPECIFICATION
REVISIONS
SUBMERSIBLE PUMP
SANITARY SEWER, SEE PLANS FOR ROUTING AND SIZE
1-1/2" TRI-CHECK COMBINATION 30"x30"x30" CONCRETE SUMP WITH FRAME AND GRATE
Addendum 004
CAST IRON PUMP COVER SEALS WITH RUBBER GASKET
GUIDE RAILS
SUBMERSIBLE PUMP
SECURE UNISTRUT PIPE SUPPORTS TO FLOOR AND WALL OF ELEVATOR PIT
4"
1/3 OF CAPACITY
FLOOR SLAB
SUPPORT FOOTING
4" THICK PAD. SEE STRUCTURAL
2"PD
PD 2/3 OF CAPACITY
2"PUMPED DISCHARGE
VALVE BOX
INDIRECTLY DISCHARGE INTO FLOOR SINK
DOUBLE C.O.T.G.
2" VENT
PUMP 1
LEVEL CONTROL CORD
PLAN VIEW
PD
FINISHED CONCRETE
2" VENT LINE, SEE PLANS FOR ROUTING AND SIZING
2"PUMPED DISCHARGE
PUMP ROOM
24"DIA. C.I. MANHOLE FRAME AND SOLID COVER (GAS TIGHT SEAL ON COVER) ADJUST FRAME TO MATCH SLOPE OF CONCRETE PAD (TYPICAL)
6" CLEANOUT CAP
FLOOR SLAB
HINGED ACCESS DOOR WITH HASP GATE VALVE CHECK VALVE LINK SEAL GUIDE RAILS STEEL COVER
PD
2" VENT
PLUMBING DETAILS
6" MIN
2/15/2016 1:02:52 PM
SECTION/ELEVATION
A1
ELEVATOR SUMP PUMP INTERCEPTOR DETAIL A2 W/OIL SCALE = NONE
GREASE INTERCEPTOR DETAIL SCALE = NONE
A4
SUMP PUMP DETAIL
A5
SCALE = NONE
SEWAGE EJECTOR DETAIL SCALE = NONE SHEET NO.
P502 1
2
3
4
5
6
PLUMBING FIXTURE SPECIFICATIONS
SYMBOL
SYMBOL
SYMBOL
P1a WATER CLOSET (PUBLIC RESTROOMS-HANDICAP): TYPE: SAME AS P1 EXCEPT MOUNTING HEIGHT. SEE ARCH. PLANS. P2 URINAL: TYPE:
WALL MOUNTED, SIPHON JET FLUSHING, VITREOUS CHINA, 3/4" TOP SPUD, LOW CONSUMPTION, 0.125 GALLON PER FLUSH. MFG: KOHLER K-4904-ET "BARDON" CARRIER: FLOOR SUPPORTED, CONCEALED IN WALL. MFG: ZURN, WADE, JOSAM OR SMITH. FLUSH VALVE:EXPOSED, MANUAL, CHROME PLATED FLUSHOMETER. 0.125 GALLON PER FLUSH. MTD HEIGHT: SEE ARCHITECTURAL DRAWINGS.
P2a URINAL (HANDICAP): TYPE: SAME AS P2 EXCEPT MOUNTING HEIGHT. SEE ARCH. PLANS. P3 LAVATORY (HANDICAP): TYPE: WALL HUNG, VITREOUS CHINA, 21" X 18" OVERALL DIMENSIONS, 3-HOLE, 4"CENTERS. MFG: KOHLER NO. K-2005 "KINGSTON". FAUCET: 4" CENTERS, METAL WRISTBLADE HANDLES, CHROME PLATED, 0.5 GPM LAMINAR FLOW AERATOR MFG: CHICAGO No. 802-317CP SUPPLIES: 1/2" SWEAT WHEEL HANDLE ANGLE STOPS WITH 3/8" O.D. FLEXIBLE RISERS, CHROME PLATED FINISH. TRAP: 1-1/4" IN X 1-1/2" OUT, 17 GA, CHROME PLATED, ADJUSTABLE, CLEANOUT PLUG, SEMI-CAST P-TRAP. MFG: MCGUIRE NO. 8902. MTD HEIGHT: SEE ARCHITECTURAL DRAWINGS FOR MOUNTING HEIGHT. NOTE: INSULATE SUPPLY AND WASTE PIPING PER SPECIFICATIONS.
DESCRIPTION
P6 WALL MOUNTED KITCHEN SINK - ADULT TAS: TYPE: SINGLE COMPARTMENT BOWL, 20 GAUGE STAINLESS STEEL WALL MOUNTED, 20 x 16 INCHES, DECK MOUNTED FAUCET, LEVER DRAIN W/OVERFLOW, WRIST BLADE HANDLES, 3-1/2 INCH BASKET DRAIN, P-TRAP, WALL BRACKET. MFG: ADVANCE TABCO MODEL 7-PS-25 NOTE: NO SUBSTITUTIONS
P19 SCIENCE LAB SINK: TYPE: COUNTERTOP MOUNTED, SINGLE COMPARTMENT, OVERALL 14"L x 10"W x 5" DEEP, CORNER DRAIN, EPOXY RESIN. MFG: PRIME INDUSTRIES INC. MODEL DPL05ADA FAUCETS: SINGLE HOLE, GOOSENECK SPOUT WITH VACUUM BREAKER, 2-1/2" METAL VANDAL PROOF LEVER HANDLES WITH COLOR CODED BUTTONS, DECK MOUNTED, CHROME PLATED. MFG: ZURN MODEL Z826U1-6M. DRAIN: 3-5/16" DIAMETER, 1-1/2" INTEGRAL TAILPIECE. MFG: PRIME INDUSTRIES INC MODEL PSO3R. SUPPLIES: 1/2" O.D. x 3/8" LOOSE KEY ANGLE STOPS WITH 3/8" O.D. FLEX RISERS. TRAP: 1-1/2" ACID WASTE POLYPROPYLENE WITH MECHANICAL JOINTS. MFG: ORION MODEL NO 1-1/2" RBP. NOTE: DOMESTIC HOT AND COLD WATER PIPING AND P-TRAPS EXPOSED BELOW ADA SINKS SHALL BE INSULATED WITH PROFLOW PF292WH TRAP COVER
ORD1 OVERFLOW ROOF DRAIN: TYPE: ROOF SUMP RECEIVER, CAST IRON BODY, BOTTOM OUTLET, COMBINATION MEMBRANE FLASHING/GRAVEL GUARD, CAST IRON DOME, 2"HIGH NON-ADJUSTABLE WATER LEVEL REGULATOR, EXTENSION (AS REQUIRED), UNDERDECK CLAMP, SIZE AS INDICATED ON DRAWINGS MFG: ZURN NO. ZC-100-2-ERC DN1 DOWNSPOUT NOZZLE: TYPE: ALL NICKEL BRONZE BODY, OPTIONAL THREADED OR NO-HUB INLET AND DECORATIVE FACE OF WALL FLANGE AND OUTLET NOZZLE. SIZE AS INDICATED ON DRAWINGS. MFG: Z-199
ACCESSORIES: WHEEL HANDLE 1/4 TURN STOP. FLEXIBLE SUPPLIES. P7 COUNTERTOP SINK (HANDICAP): TYPE: TWO COMPARTMENT - SELF RIMMING-18 GAUGE STAINLESS STEEL, 33"x22"x9-1/4". MFG: KOHLER K-3847-3 "TOCCATA" FAUCET: 8" CENTERS, 7- 5/8"L TYPE SWING SPOUT, 2 3/8" METAL VANDAL PROOF WRIST BLADE HANDLES WITH COLOR CODED BUTTONS, DECK MOUNTED, CHROME PLATED SOLID BRASS CONSTRUCTION, 1.5 GPM. MFG: ZURN FAUCET MODEL No. Z871A4-XL-17F DRAIN: GRID WITH 1-1/4" TAIL PIECE. SUPPLIES: 1/2" SWEAT WHEEL HANDLE ANGLE STOPS WITH 3/8" O.D. RIGID RISERS. TRAP: 1-1/4" IN X 1-1/2" OUT, 17 GA, CHROME PLATED, ADJUSTABLE, CLEANOUT PLUG, SEMI-CAST P-TRAP. MFG: MCGUIRE NO. 8902 WITH 17 GAUGE CONTINUOUS WASTE. NOTE: INSULATE SUPPLY AND WASTE PIPING PER SPECIFICATIONS, MINIMUM CABINET SIZE 24"
P20 UTILITY CONTROL (CONTROL PANEL): TYPE: FLUSH MOUNTED, NEMA 1 PANEL, WITH WHITE POWDER COAT FINISH. TWO POSITION KEYED SELECTOR SWITCH, EMERGENCY STOP PUSH/PULL OPERATOR, ON/OFF UTILITY SELECTOR SWITCHES FOR EACH UTILITY, GREEN ENABLED PILOT LIGHT FOR EACH UTILITY ENABLED, RED PILOT LIGHT FOR EACH UTILITY OFF, 120 VAC INPUT, 24VDC, 5A OUTPUT, DESIGNATED DISCRETE INPUTS AND RELAY OUTPUTS, UL 508A CERTIFIED, FAN ENABLED. MFG: LAB SAFETY SYSTEMS CCS-UCP-SC-4U-PC-KL-F UTILITY CONTROL (SOLENOID PANEL): TYPE: FLUSH MOUNTED NEMA 1 PANEL WITH WHITE POWDER COAT FINISH. BRASS WATER CONNECTIONS, BLACK IRON GAS CONNECTIONS, ASCO GAS SOLENOID UL RATED FOR GAS SERVICE. UL RATED GAS BALL VALVES. LEAD FREE CONSTRUCTION, UL 508A CERTIFIED. MFG: LAB SAFETY SYSTEMS CSS-SP-3-111-120AC-PC-CL-WHA
5
UTILITY CONTROL (ELECTRIC PANEL): TYPE: FLUSH MOUNTED NEMA 1 PANEL WITH WHITE POWDER COAT FINISH. ELECTRICALLY HELD CONTACTORS, BRANCH CIRCUIT PROTECTION, UL 508A CERTIFIED. MFG: LAB SAFETY SYSTEMS CSS-EP-12-PCG-CL UTILITY CONTROL (REMOTE PANIC PANEL): TYPE: SURFACE MOUNTED NEMA 1 PANEL WITH GREY POWDER COAT, EMERGENCY STOP PUSH/PULL OPERATOR, UL 508A CERTIFIED. MFG: LAB SAFETY SYSTEMS CSS-RP-CC-SOL.. GI-1 OIL INTERCEPTOR: TYPE: STEEL INTERCEPTOR WITH GRAY DUCO COATING INSIDE AND OUTSIDE AND FLOW CONTROL FITTING. MODEL: SMITH NO. 8560 MFG: SMITH, HYDRCRETE, RINKER, OR APPROVED EQUAL.
B
SEP-1
5
ACCESSORIES: ELKAY MODEL GFOBG3017RSS BOTTOM GRID. WADE MODEL 5750 PLASTER TRAP. CHROME PLATE 17 GAGE BRASS P-TRAP WITH CLEAN-OUT PLUG AND ARM WITH ESCUTCHEON. WHEEL HANDLE 1/4 TURN STOP. FLEXIBLE SUPPLIES.
P18a GAS TURRET: TYPE: SINGLE TURRET WITH SERRATED TIP, CHROME PLATED BRASS BODY, 3/8" NPT FEMALE INLET IN BASE. BLACK PLASTIC BASE GASKET. FURNISH WITH "GAS" INDEX . MFG: T&S BRASS MODEL BL-4200-01.
RD1 ROOF DRAIN: TYPE: ROOF SUMP RECEIVER, POWDER COATED CAST IRON SIDE OUTLET ROOF DRAIN/ TOP OVERFLOW WITH FLASHING CLAMP, INTEGRAL GRAVEL STOP, SECURED DUCTILE, IRON DOME, UNDERDECK CLAMP,LOW PROFILE, OVERFLOW STRAINER, NO HUB OUTLETS, SIZE OF OUTLETS AS INDICATED ON DRAWINGS. MFG: FROET NO. 100C_LP-OFS-DC
R
D
PROJECT
ASME A112.18. 1M; CHROME PLATED BRASS SUPPLY WITH 8" GOOSENECK SPOUT, VANDAL PROOF WATER ECONOMY AERATOR WITH MAXIMUM 1.5 GPM FLOW, WRISTBLADE HANDLES AND 1/4 TURN CERAMIC DISK VALVE CARTRIDGES. MOEN MODEL 8225SMF15 NO SUBSTITUTIONS
MFG: NOTE:
P18 GAS TURRET: TYPE: TURRET WITH TWO 180 DEGREE SERRATED TIPS, CHROME PLATED BRASS BODY, 3/8" NPT FEMALE INLET IN BASE. BLACK PLASTIC BASE GASKET. FURNISH WITH "GAS" INDEX . MFG: T&S BRASS MODEL BL-4200-02..
ROOF DRAIN SPECIFICATIONS
Abbas 2016.02.15 13:25:02-07'00'
P5 ART ROOM STAINLESS STEEL SINK: TYPE: SINGLE COMPARTMENT BOWL. ASME A112.19.3; 36 x 20 x 9 INCH DEEP OUTSIDE DIMENSIONS, 18 GAGE THICK, TYPE 304 STAINLESS STEEL, UNDERMOUNT WITH 6-5/8" APRON, COVED CORNERS, AND POLISHED SATIN FINISH, UNDERCOATED, CRUMBCUP AND TAILPIECE. MFG: ELKAY ECTRUF30179R NOTE: NO SUBSTITUTIONS
TRIM:
102840 I C E N S E E SS G IO N A L E N
OF
FS1 FLOOR SINK: TYPE: CAST IRON BODY WITH WHITE ACID RESISTING ENAMEL BODY INTERIOR, SLOTTED 3/4 LOOSE SET GRATE ALUMINUM ANTI-SPASH DOME STRAINER, DEEP SEAL P-TRAP, DIAMETER OF OUTLET AS SHOWN ON DRAWINGS. MFG: ZURN NO. Z-1901-Z1000. NOTE: PROVIDE WITH PROSET TRAP GUARD WATER SAVING DEVICE. SIZE AS INDICATED BY DRAIN.
P17 SCIENCE LAB SINK (HANDICAP): TYPE: COUNTERTOP MOUNTED, SINGLE COMPARTMENT, OVERALL 25"L x 15"W x 4.8" DEEP, CORNER DRAIN, EPOXY RESIN. MFG: PRIME INDUSTRIES INC. MODEL PL55ADA FAUCET: SINGLE HOLE, GOOSENECK SPOUT WITH VACUUM BREAKER, 2-1/2" METAL VANDAL PROOF LEVER HANDLES WITH COLOR CODED BUTTONS, DECK MOUNTED, CHROME PLATED MFG: ZURN MODEL Z826U1-6M. DRAIN: 3-5/16" DIAMETER, 1-1/2" INTEGRAL TAILPIECE PRIME INDUSTRIES INC MODEL PSO3R. SUPPLIES: 1/2" O.D. x 3/8" LOOSE KEY ANGE STOPS WITH 3/8" O.D. FLEX RISERS. TRAP: 1-1/2" ACID WASTE POLYPROPYLENE WITH MECHANICAL JOINTS. MFG: ORION MODEL NO 1-1/2" RBP. NOTE: DOMESTIC HOT AND COLD WATER PIPING AND P-TRAPS EXPOSED BELOW ADA SINKS SHALL BE INSULATED WITH PROFLOW PF292WH TRAP COVER.
A
ABBAS SHIRIAN
P4 COUNTERTOP SINK (HANDICAP): TYPE: SINGLE COMPARTMENT, 18-GAUGE STAINLESS STEEL, TOP MOUNTED, 3-HOLE, 25"X22" . MFG: KOHLER MODEL NO. K-3348-3 FAUCET: POLISHED CHROME-PLATED 8", BRASS DECK FAUCET WITH A 3-1/2" SWING GOOSENECK SPOUT, QUARTER TURN CERAMIC DISC CARTRIDGES, 4" VANDAL RESISTANT COLORCODED METAL WRIST BLADE HANDLES, VANDAL-RESISTANT PRESSURE COMPENSATING FEMALE AERATOR. MFG: ZURN MODEL NO. Z871A4-XL-2F DRAIN: GRID WITH 1-1/4" TAIL PIECE. SUPPLIES: 1/2" SWEAT WHEEL HANDLE ANGLE STOPS WITH 3/8" O.D. RIGID RISERS. TRAP: 1-1/4" IN X 1-1/2" OUT, 17 GA, CHROME PLATED, ADJUSTABLE, CLEANOUT PLUG, SEMI-CAST P-TRAP. MFG : MCGUIRE NO. 8902. NOTE: INSULATE SUPPLY AND WASTE PIPING PER SPECIFICATIONS, MINIMUM CABINET SIZE 24"
P16 WALL HYDRANT: TYPE: BRONZE HYDRANT, FREEZE-PROOF, INTEGRAL VACUUM BREAKER, WITH LOOSE-KEY, 3/4" INLET AND 3/4" GARDEN HOSE OUTLET, LOOSE KEY HANDLE, VERIFY WALL THICKNESS BEFORE ORDERING. MFG: ZURN NO. Z-1310.
E O F T EX
L
FD2 FLOOR DRAIN: TYPE: PROLINE DRAIN, 18 GAUGE, 304 STAINLESS STEEL, 1-1/2" WIDTH, VERTICAL COVER, REFER TO ARCHITECTURAL PLAN FOR LENGTHS. MFG: QUICKDRAIN PROLINE DRAIN NOTE: PROVIDE WITH PROSET TRAP GUARD WATER SAVING DEVICE. SIZE AS INDICATED BY DRAIN.
5
PR
P15 EXPANSION TANK: TYPE: PRE-PRESSURED TANK WITH SEALED-IN AIR CHARGE OF 60 PSI. SIZE: 6.4 GAL, TOTAL VOLUME, 3.15 MAX. ACCEPTANCE. MFG: AMTROL NO. ST-12C.
AT
EE
DESCRIPTION
ARCHITECT
S
P14 WATER HAMMER ARRESTOR: TYPE: STAINLESS STEEL CONSTRUCTION, PRE-CHARGED, PERMANENTLY SEALED. SEE SHOCK ABSORBER SCHEDULE FOR UNIT SIZE MFG: JAY R. SMITH 5000 SERIES. NOTE: PROVIDE AND INSTALL BEHIND LOCKING 14"X14" ACCESS PANEL.
FD1 FLOOR DRAIN: TYPE: 7" DIAMETER, ROUND TYPE "B" STRAINER. POLISHED BRONZE, CAST IRON BODY WITH BOTTOM OUTLET, COMBINATION INVERTABLE MEMBRANE CLAMP, DEEP SEAL P-TRAP, VANDAL-PROOF SECURED TOP, DIAMETER OF OUTLET AS SHOWN ON DRAWINGS. MFG: ZURN NO. Z-415-B-VP-Z1000. NOTE: PROVIDE WITH PROSET TRAP GUARD WATER SAVING DEVICE. SIZE AS INDICATED BY DRAIN.
SYMBOL
P11 WASHER BOX: TYPE: CENTER DRAIN, BRASS 1/4 TURN VALVE WITH WATER HAMMER ARRESTERS, FRAME ACCOMMODATES UP TO 1" DRYWALL, BOTTOM OUTLET, BOX DIMENSIONS 8 1/4" X 6 1/8" X 3 3/4", FRAME DIMENSIONS 10 3/16" X 8 13/16". SUPPLIES: SEE PLUMBING ROUGH-IN SCHEDULE. MFG: IPS MODEL No: W4700HA.
IN
SYMBOL
P1 WATER CLOSET: TYPE: FLOOR MOUNT, SIPHON JET, 1-1/2" TOP-SPUD, 1.28 GALLON PER FLUSH, ELONGATED, VITREOUS CHINA, MFG: KOHLER NO. K-4405 "HIGHLINE". SEAT: SOLID PLASTIC, OPEN FRONT, FIRE RETARDANT, ELONGATED, WITHOUT COVER, STAINLESS STEEL CHECK HINGE. MFG: OLSONITE NO. 95. FLUSH VALVE: EXPOSED, MANUAL, CHROME PLATED, DIAPHRAGM TYPE, FLUSHOMETER, 1.28 GALLON PER FLUSH. MFG: SLOAN NO. 111-1.28 "ROYAL" CARRIER: ZURN, WADE JOSAM OR SMITH (1,000 LBS. CAPACITY) MTD. HEIGHT: SEE ARCHITECTURAL DRAWINGS.
P13 ICE MACHINE BOX: TYPE: SPACE SAVER DESIGNED FOR ICEMAKER HOOK-UP. ROUGH OPENING: 10"Wx8-3/4"Hx3-1/2"D. VALVE: COMPRESSION ANGLE VALVE 1/2" FIP INLETx1/4" OUTLET. MFG: GUY GRAY MODEL NO.BIM875.
FLOOR DRAIN/SINK SPECIFICATIONS
DESCRIPTION
P10 DRINKING FOUNTAIN (HANDICAP): TYPE: WALL HUNG, ADA COMPLIANT, BI-LEVEL, FRONT PUSH BUTTON, 18 GA. STAINLESS STEEL, VANDAL RESISTANT CHROME PLATED BUBBLER, VANDAL RESISTANT BOTTOM PLATES, INLINE STRAINER, WITH BOTTLE FILLING STATION. MFG: ELKAY EZH20 VRCGRNTL8WSK ACCESSORY: APRON LKAPREZL SUPPLIES: 1/2" X 3/8" WHEEL ANGLE STOPS WITH 3/8" O.D. FLEX RISERS. TRAP: 1-1/4" 17 GA. POLISHED CHROME TUBULAR P-TRAP. CARRIER:CONCEALED BY ZURN, WADE, JOSAM, OR SMITH. MTD HEIGHT: SEE ARCHITECTURAL DRAWINGS.
P12 EMERGENCY SHOWER/EYEWASH (HANDICAP): TYPE: COMBINATION SHOWER AND EYE/FACE WASH, STAINLESS STEEL 11" ROUND BOWL WITH LAMINAR FLOW SPRAY HEADS, ABS PLASTIC SHOWERHEAD WITH FLOW CONTROL, STAY OPEN BALL VALVE WITH STAINLESS STEEL BALL AND STEM, 1-1/4" IPS INLET. FURNISH WITH DUST COVER, LARGE SHOWER/EYE WASH SIGN, AND HAWS 9201H THERMOSTATIC MIXING VALVE. MFG: HAWS MODEL 8300-8309
G1 GREASE INTERCEPTOR: TYPE: PRE-CAST CONCRETE, 1500 GALLON LIQUID CAPACITY, TWO COMPARTMENT, TWO MANHOLES, CLEANOUT CAP, 4" WASTE CONNECTIONS, 2" VENT CONNECTION, INTERNAL PIPING, GAS KEYED NON-VENTED (GAS TIGHT) MANHOLE FRAME AND COVER, ADJUSTMENT RINGS, REINFORCED CONSTRUCTION. FURNISH AND INSTALL AN AERATION SYSTEM BY AERO-LIFE AERATION SYSTEMS (866-244-3335) TO INCLUDE ADEQUATELY SIZED SYSTEM FEATURING AIR PUMP, DIFFUSION, DIAPHRAGMS, PVC SUPPORT SKID, 3/8" AIR TUBING, 1-1/2" DIA. PIPE CONDUIT WITH LONG RADIUS BENDS, AND CONNECTIONS. MFG: SMITH, HYDROCRETE, RINKER, OR APPROVED EQUAL.
C
6
PLUMBING FIXTURE SPECIFICATIONS
RPZ REDUCED PRESSURE BACKFLOW PREVENTER: TYPE: 2-1/2" SIZE WITH THREADED CONNECTION, COMPLETE WITH 2 SPRING LOADED CHECK VALVES, BALL VALVES, TEST COCKS. 12 PSI LOSS AT 80 GPM. SERVICE:MECH. COOLING TOWER MAKE-UP. MFG: FEBCO NO. 860Y-AGD. NOTE: AIR GAP DRAIN SHALL BE PIPED TO NEAREST FLOOR DRAIN, FLOOR SINK, OR AS INDICATED ON DRAWINGS.
D
5
PLUMBING FIXTURE SPECIFICATIONS TMV THERMOSTATIC MIXING ASSEMBLY (DOMESTIC HOT WATER): TYPE: HIGH LOW DUAL STAGE THERMOSTATIC WATER MIXING SYSTEM SET FOR 120F. LARGE AND SMALL TYPE THERMOSTATIC WATER MIXING VALVES, ADJUSTABLE HIGH TEMPERATURE LIMIT STOP, INLET CHECKSTOPS, WALL SUPPORT, OUTLET BALL VALVE, 1 GPM MINIMUM FLOW CAPACITY, INLET MANIFOLD PIPING, OUTLET PRESSURE REGULATING VALVE AND PRESSURE GAUGES, COLOR-COATED DIAL THERMOMETER (0 TO 140F), FACTORY ASSEMBLED AND TESTED, ROUGH FINISH. INLET: 2". OUTLET: 2". MFG: LEONARD NO. TM-2020B-LF-DT.
E
4
P8 SHOWER (LOCKER ROOMS-HANDICAP): TYPE: BUILT-UP PER ARCHITECTURAL SPECIFICATIONS. VALVE: PRESSURE BALANCING TYPE, BRONZE/SS CONSTRUCTION, ADJUSTABLE HIGH TEMP LIMIT STOP, INTEGRAL CHECK STOPS, METAL LEVER HANDLE, ESCUTCHSON, 1.5 GPM SHOWER HEAD, 30" SLIDING BAR, HAND HELD SHOWER HEAD, SS 60" FLEXIBLE HOSE, VACUUM BREAKER, WALL FLANGE, ADA APPROVED. MFG: SYMMONS NO. 1-25-FSB-X. DRAIN: ZURN NO. Z-415-B-VP.
200 Longhorn Street Vega, TX 79092
3
VEGA ISD HIGH SCHOOL
2
ST
1
P9 SERVICE SINK: TYPE: FLOOR MOUNTED, 24" X 24" X 10" DEEP, MOLDED STONE, 3" DRAIN OPENING. MFG: FIAT NO. MSB-2424. FAUCET: POLISHED CHROME, WALL MOUNTED 42" ABOVE FLOOR, WALL BRACE, VACUUM BREAKER, INTEGRAL CHECK STOPS. MFG: CHICAGO NO. 897-CP-C. DRAIN: INTEGRAL WITH STAINLESS STEEL STRAINER. TRAP: 3" CAST IRON "P" TRAP. ACCESSORIES: HOSE AND HOSE BRACKET NO. 832AA, STAINLESS STEEL, 24" X 3" MOP HANGER NO. 889-CC, VINYL BUMPER GUARD NO. E-77-AA.
SEWAGE EJECTOR (CLEAR WATER WASTE) NON-CLOGGING BRONZE VORTEX IMPELLER, CAST IRON SWITCH CASE, BASE, MOTOR AND PUMP HOUSING, CAST IRON CLASS 25-30 CASTING, CORROSION RESISTANT POWDER COATED EPOXY FINISH, 75 GPM, 20 FOOT UL LISTED 3 WIRE NEOPRENE CORD-PLUG, 1/2 HP, 115V/SINGLE PHASE/60HZ, 15.5 AMPS, 3450 RPM, HERMETICALLY SEALED, AUTOMATIC RESET THERMAL OVERLOAD PROTECTION, CARBON AND CERAMIC SHAFT SEAL, 130 DEGREE F MAXIMUM FLUID TEMPERATURE, PASSES 3/4" SPHERICAL SOLIDS.
Addendum 004
BASIS OF DESIGN:ZOELLER MODEL NUMBER N161 HIGH HEAD FLOW MATE. ALTERNATOR PANEL: HAND-OFF-AUTO TOGGLE SWITCH FOR EACH PUMP, GREEN PUMP RUN PILOT LIGHT FOR EACH PUMP, ALARM TEST AND PILOT SWITCHES, RED ALARM BEACON, AUXILIARY DRY CONTACT, HIGH WATER ALARM, CIRCUIT BREAKER FOR EACH PUMP, MAGNETIC STARTER FOR EACH PUMP, ALTERNATING MECHANISM, NUMBER TERMINAL STRIP FOR CONNECTING PUMPS AND VARIABLE LEVEL FLOAT SWITCHES, NEMA 4X ENCLOSURE, INTEGRAL AUXILIARY TERMINAL BOARD BOARD CONNECTIONS FOR REMOTE ALARM, (3) VARIABLE LEVEL FLOAT SWITCH CONTROL OPERATION, (3) FLOAT SWITCHES INCLUDED WITH PACKAGE. 12"Hx10"Wx6"D. FURNISH 1 SET OF DRY CONTACTS FOR INTERFACE WITH FMS.
REVISIONS 4
02/05/16
ADDENDUM #02
5
02/15/16
ADDENDUM #04
BASIS OF DESIGN:ZOELLER MODEL NUMBER 10-1042 BASIN: 4 FOOT DIAMETER x 6'-6" DEEP FIBERGLASS SUMP WITH SIDE VALVE ACCESS. ANTIFLOAT BOTTOM, FURNISH WITH STAINLESS STEEL GUIDE RAILS, AND STEEL HINGED DOOR. SIDE DISCHARGE, VENT TO EXIT OUT THE SIDE OF THE BASIN. BASIS OF DESIGN: AK INDUSTRIES MODEL NO: BASIN: GB-48X078-201, VALVE BOX: GB-48x48-VB, COVER: LBS: 48VB COVER, 3" PIPE OUTLET PLAK300G-V, WITHOUT FLOATS.
DRAWN BY
SP
REVIEWED BY
AS
DATE PROJECT NO:
02.15.2016 14-0424.002
DRAWING NAME
A
2/15/2016 1:02:53 PM
PLUMBING SPECIFICATIONS
SHEET NO.
P701 1
2
3
4
5
6
1
2
3
4
5
6
GENERAL SHEET NOTES
I.
R2.9 RV
J. K. L.
100B T / A3
M. N. O.
RU
P.
GIRLS VARSITY B111
SHEET KEYNOTES T09
5
A S
OF
T33
(3) 1-1/4" CONDUITS.
E
2
XRB
E
G
SS
IS T E R G IO N A L E N
John Heck 2016.02.15 15:02:58-07'00'
INTERIOR, WALL MOUNTED SPEAKER, FOR DISTRIBUTED PAGING / INTERCOM SYSTEM. MOUNT AT +144” A.F.F. GAME AND SHOT CLOCK LOCATION. WALL MOUNTED A/V EQUIPMENT RACK FOR GYM SOUND SYSTEM. PROVIDE ROUGH-IN AND STRUCTURAL BACKING PER DETAIL A5 ON SHEET T504 . REFER TO A/V PATHWAY DIAGRAM ON SHEET T601 FOR BOX AND CONDUIT REQUIREMENTS.
T23 T33
82984
R
T21 J1
E O F T EX
AT
JOHN F. HECK IV PR
D
J
ARCHITECT
WIRELESS ACCESS POINT LOCATION. PROVIDE QTY (2) CAT 6 CABLES (AS SHOWN), AND TERMINATED WITH MALE RJ-45 MODULAR CONNECTORS AT LOCATION WITH MINIMUM 12" SLACK. AUDIO/VISUAL PLUG-IN CONNECTION PANEL FOR LOCAL SOUND SYSTEM. WIREMOLD FLOOR BOX MODEL # RFB6E-OG. PROVIDE (1) 1-1/4" CONDUIT FOR DATA CABLING AND (1) 3/4" CONDUIT FOR POWER AND (1) 1-1/4" CONDUITS FOR A/V AND (1) 1-1/4" FOR FUTURE USE. DO NOT DAISY CHAIN FLOOR BOXES FOR DATA CABLING PATHWAYS. REFER TO DETAIL B4 ON SHEET T502 FOR ADDITIONAL INFORMATION. REFER TO ELECTRICAL PLANS FOR ADDITIONAL INFORMATION.
T16 T18
PA B102
NOT ALL NOTES USED
R
H.
D
E
E
G.
EE
D. E. F.
IN
B. C.
PROPERLY FIRE STOP AND SEAL ALL PENETRATIONS THROUGH WALLS, FLOORS, CEILINGS, AND ROOF AS PER OWNER, CODE, AND AHJ. PRIOR TO INSTALLATION OF CABLE TRAY COORDINATE LOCATIONS WITH ALL OTHER TRADES. NOT ALL PARTS AND PIECES ARE SHOWN FOR A COMPLETE SYSTEM. CONTRACTOR IS RESPONSIBLE FOR PROVIDING A COMPLETE END-TO-END WARRANTED SOLUTION FOR THE HORIZONTAL CABLING. ALL CABLING TO BE PLENUM RATED THROUGHOUT THE BUILDING. ALL COMMUNICATIONS CABLING TO MEET OR EXCEED CAT6 STANDARDS. TELECOMMUNICATIONS OUTLETS TO BE MOUNTED AT +18" A.F.F. (BOTTOM OF BOX) UNLESS OTHERWISE NOTED. FOR EXAMPLE, DEVICES SPECIFIED AT +18" A.F.F. SHALL MATCH THE STANDARD MOUNTING HEIGHT FOR POWER RECEPTACLES AND TELECOMMUNICATIONS OUTLETS. DEVICES SPECIFIED AT + 48" A.F.F. SHALL MATCH THE STANDARD MOUNTING HEIGHT FOR LIGHT SWITCHES ETC. ALL CONDUITS FOR TELECOMMUNICATIONS OUTLETS SHALL BE STEEL, THINWALL ELECTRICAL METALLIC TUBING (TYPE EMT) UNLESS OTHERWISE NOTED. UNDER NO CIRCUMSTANCES SHALL FLEXIBLE CONDUIT BE USED FOR PATHWAYS INDICATED ON THIS SHEET. ALL CONDUITS ARE TO BE, AT A MINIMUM, 1” TRADE SIZE, UNLESS OTHERWISE NOTED. ALL CONDUITS FOR TELECOMMUNICATIONS OUTLETS ARE TO BE STUBBED TO NEAREST CABLE TRAY. CONTRACTOR IS TO ENSURE THAT NO CONDUIT EXCEEDS 40% FILL. CABLE TRAY SYSTEMS SHOWN ON THIS SHEET SHALL BE USED FOR VOICE AND DATA CABLING ONLY. ALL OTHER SYSTEMS INCLUDING, BUT NOT LIMITED TO, FIRE ALARM, SECURITY, HVAC CONTROL, ETC. SHALL BE SUPPORTED BY OTHER MEANS. J-HOOKS ATTACHED TO THE CABLE TRAY SUPPORTS WILL BE PERMITTED. LIKEWISE, ANY CONDUITS PROVIDED FOR VOICE AND DATA CABLING IS NOT TO BE USED BY ANY OTHER SYSTEM, HENCE, SEPARATE CONDUITS MAY NEED TO BE PROVIDED FOR THE SUPPORT OF THESE SYSTEMS. NUMBER ADJACENT TO TELECOMMUNICAITONS OUTLET SYMBOL REPRESENTS NUMBER OF CAT 6 CABLES TO BE INSTALLED AND TERMINATED AT THAT LOCATION. A "B" ADJACENT TO AN OUTLET LOCATION REPRESENTS A ROUGH-IN ONLY LOCATION, PROVIDE BOX, CONDUIT, AND BLANK FACEPLATE. FOR ALL EXTERIOR WALL-MOUNTED DEVICES, PROVIDE BACKBOX AND EXTENSION RING, TOTAL DEPTH AS REQUIRED TO MATCH THICKNESS OF COMPLETE WALL & INSULATION ASSEMBLY. WIRELESS ACCESS POINTS IN GYMNASIUM WILL HAVE WIRE GUARDS. ALL CONDUIT TURNS FOR A/V AND IT CONDUITS SHALL BE "SWEEP" TYPE, NO BEND FITTINGS ARE PERMITTED. ALL CONDUIT PATHWAYS SHALL BE PROVIDED WITH NYLON BUSHINGS TO PROTECT CABLES, REGARDLESS OF WHETHER THEY TERMINATE IN A DEVICE OR JUNCTION BOX. CONTRACTOR TO VERIFY ALL CABLE COUNTS AND NUMBER OF PATCH PANELS REQUIRED. GROUP DATA OUTLETS TOGETHER WITH POWER OUTLETS (WHERE APPLICABLE). REFER TO "EP" SERIES SHEETS FOR POWER OUTLET LOCATIONS. FOR ALL OUTLETS INSTALLED IN ARTS/MUSIC/DRAMA AREAS, CLASSROOMS, LABS, MISC. LEARNING AREAS, OFFICES AND OTHER ACOUSTICALLY-RATED PARTITIONS (AS INDICATED ON ARCHITECTURAL DRAWINGS): MAINTAIN A MINIMUM OF 12 INCHES SEPARATION BETWEEN OUTLETS ON OPPOSITE SIDES OF PARTITION. PROVIDE ACOUSTICAL OUTLET BACKER PUTTY (AS MANUFACTURED BY KINETICS NOISE CONTROL, OR EQUAL). PUTTY PADS SHALL MAINTAIN ACOUSTICAL RATINGS PER ASTM C 919 AND ASTM E 497, AND BE TESTED TO UL 263 (ASTM E119) AND UL 1479 (ASTM E814) STANDARDS.
ST
A.
PROJECT
5
RFB6E-OG 4 J3 5
RS
VEGA ISD HIGH SCHOOL
IC S
RT
T18 TYP.
T21 TYP.
RR
WAP
T09 TYP.
RQ RP
T16 J S IC
C
TYP.
J2 5
T23 TYP.
GYMNASIUM B100 TYP.
IC S
T23
STAIR 2 169 STOR B138
HALL B100B
RN
A RM
200 Longhorn Street Vega, TX 79092
RU
T09 TYP.
RK
WAP
T18 TYP.
100B T / A3
S IC
HALL B140 B
RJ RG Addendum 004 RF REVISIONS
RE
4
02/05/16
ADDENDUM #02
5
02/15/16
ADDENDUM #04
KEY PLAN - NTS
DRAWN BY AREA C
EXISTING
CSK/MAD
REVIEWED BY
GR
DATE
R2.1
LEVEL 1 ABOVE
R2
A
MATCH LINE
02.15.2016
PROJECT NO:
14-0424.002
DRAWING NAME
R1.8
LOWER LEVEL TECHNOLOGY SYSTEMS PLAN AREA A
AREA B AREA A
A3
LOWER LEVEL TECHNOLOGY SYSTEMS PLAN - AREA A SCALE: 1/8" = 1'-0"
0'
1
2
3
4
5
4'
8'
16'
NORTH
E NE H LLIIN CH ATTC M MA
2/15/2016 2:09:41 PM
NORTH
SHEET NO.
T100A 6
1
2
3
4
5
6
GENERAL SHEET NOTES
R2.9
4
H.
DS
DS
2 VEST 124
3
I.
CR
J. K. L.
3 WAP
G 6E-O RFB 4
M. N. O.
BOYS 118
T24
P.
TYP.
T18 TYP.
R7
G RE 6E-O SCO ER RFB P 4 KEE
T11
FILM
TYP.
SHEET KEYNOTES
J
FAM RR 116
J4
DS
5
T22
J J
DS
RU
SCOREBOARD LOCATION. SEE ARCHITECTURAL GYNUSMIUM EQUIPMENT SPECIFICAFTIONS. WALL MOUNTED WIRELESS ACCESS POINT LOCATION. PROVIDE QTY (2) CAT 6 CABLES (AS SHOWN), AND TERMINATED WITH MALE RJ-45 MODULAR CONNECTORS AT LOCATION WITH MINIMUM 12" SLACK. STANDARD TELECOMMUNICATIONS OUTLET ABOVE CEILING GRID WITH (2) CAT6 CABLES (UNLESS OTHERWISE NOTED).
T24
J5
RT
T28
OF
WAP
XRB
A
JOHN F. HECK IV 82984
E
E
BLEACHER 200B
E O F T EX
AT
R
G
SS
IS T E R G IO N A L E N
John Heck 2016.02.15 15:02:51-07'00'
PROJECT
VEGA ISD HIGH SCHOOL
T15
RS
2
RR
J S 1 J6
TYP.
5 J
0" 32' -
RQ
T11
T22
RP
J S 1 J6
T15
0" 17' -
0" 12' -
J S 2 J6
C
STAIR 2 169
0" 31' -
J J6
5
CORRIDOR 110
R5
S 2
0" 12' -
J S 1 J6 5
RN J S 1 J6
A
VEST 101
5
RM 0" 32' -
RK
STOR 164
200 Longhorn Street Vega, TX 79092
D
T15 T16 T18
3
PR
RV
STUDENT COMMONS 102
INTERIOR IP BASED SECURITY CAMERA POE LOCATION. PROVIDE (2) CAT6 CABLES (UNLESS OTHERWISE NOTED), TERMINATED WITH MALE RJ-45 MODULAR CONNECTORS AT LOCATION WITH MINIMUM 12" SLACK. 1-1/4" PATHWAY FOR TELECOMMUNICATIONS CABLING. AUDIO/VISUAL PLUG-IN CONNECTION PANEL FOR LOCAL SOUND SYSTEM. WIREMOLD FLOOR BOX MODEL # RFB6E-OG. PROVIDE (1) 1-1/4" CONDUIT FOR DATA CABLING AND (1) 3/4" CONDUIT FOR POWER AND (1) 1-1/4" CONDUITS FOR A/V AND (1) 1-1/4" FOR FUTURE USE. DO NOT DAISY CHAIN FLOOR BOXES FOR DATA CABLING PATHWAYS. REFER TO DETAIL B4 ON SHEET T502 FOR ADDITIONAL INFORMATION. REFER TO ELECTRICAL PLANS FOR ADDITIONAL INFORMATION.
S
G 6E-O RFB 4
T11
ARCHITECT
R
WAP
E
D
G
A3 / T101B
E
G.
EE
D. E. F.
IN
B. C.
PROPERLY FIRE STOP AND SEAL ALL PENETRATIONS THROUGH WALLS, FLOORS, CEILINGS, AND ROOF AS PER OWNER, CODE, AND AHJ. PRIOR TO INSTALLATION OF CABLE TRAY COORDINATE LOCATIONS WITH ALL OTHER TRADES. NOT ALL PARTS AND PIECES ARE SHOWN FOR A COMPLETE SYSTEM. CONTRACTOR IS RESPONSIBLE FOR PROVIDING A COMPLETE END-TO-END WARRANTED SOLUTION FOR THE HORIZONTAL CABLING. ALL CABLING TO BE PLENUM RATED THROUGHOUT THE BUILDING. ALL COMMUNICATIONS CABLING TO MEET OR EXCEED CAT6 STANDARDS. TELECOMMUNICATIONS OUTLETS TO BE MOUNTED AT +18" A.F.F. (BOTTOM OF BOX) UNLESS OTHERWISE NOTED. FOR EXAMPLE, DEVICES SPECIFIED AT +18" A.F.F. SHALL MATCH THE STANDARD MOUNTING HEIGHT FOR POWER RECEPTACLES AND TELECOMMUNICATIONS OUTLETS. DEVICES SPECIFIED AT + 48" A.F.F. SHALL MATCH THE STANDARD MOUNTING HEIGHT FOR LIGHT SWITCHES ETC. ALL CONDUITS FOR TELECOMMUNICATIONS OUTLETS SHALL BE STEEL, THINWALL ELECTRICAL METALLIC TUBING (TYPE EMT) UNLESS OTHERWISE NOTED. UNDER NO CIRCUMSTANCES SHALL FLEXIBLE CONDUIT BE USED FOR PATHWAYS INDICATED ON THIS SHEET. ALL CONDUITS ARE TO BE, AT A MINIMUM, 1” TRADE SIZE, UNLESS OTHERWISE NOTED. ALL CONDUITS FOR TELECOMMUNICATIONS OUTLETS ARE TO BE STUBBED TO NEAREST CABLE TRAY. CONTRACTOR IS TO ENSURE THAT NO CONDUIT EXCEEDS 40% FILL. CABLE TRAY SYSTEMS SHOWN ON THIS SHEET SHALL BE USED FOR VOICE AND DATA CABLING ONLY. ALL OTHER SYSTEMS INCLUDING, BUT NOT LIMITED TO, FIRE ALARM, SECURITY, HVAC CONTROL, ETC. SHALL BE SUPPORTED BY OTHER MEANS. J-HOOKS ATTACHED TO THE CABLE TRAY SUPPORTS WILL BE PERMITTED. LIKEWISE, ANY CONDUITS PROVIDED FOR VOICE AND DATA CABLING IS NOT TO BE USED BY ANY OTHER SYSTEM, HENCE, SEPARATE CONDUITS MAY NEED TO BE PROVIDED FOR THE SUPPORT OF THESE SYSTEMS. NUMBER ADJACENT TO TELECOMMUNICAITONS OUTLET SYMBOL REPRESENTS NUMBER OF CAT 6 CABLES TO BE INSTALLED AND TERMINATED AT THAT LOCATION. A "B" ADJACENT TO AN OUTLET LOCATION REPRESENTS A ROUGH-IN ONLY LOCATION, PROVIDE BOX, CONDUIT, AND BLANK FACEPLATE. FOR ALL EXTERIOR WALL-MOUNTED DEVICES, PROVIDE BACKBOX AND EXTENSION RING, TOTAL DEPTH AS REQUIRED TO MATCH THICKNESS OF COMPLETE WALL & INSULATION ASSEMBLY. WIRELESS ACCESS POINTS IN GYMNASIUM WILL HAVE WIRE GUARDS. ALL CONDUIT TURNS FOR A/V AND IT CONDUITS SHALL BE "SWEEP" TYPE, NO BEND FITTINGS ARE PERMITTED. ALL CONDUIT PATHWAYS SHALL BE PROVIDED WITH NYLON BUSHINGS TO PROTECT CABLES, REGARDLESS OF WHETHER THEY TERMINATE IN A DEVICE OR JUNCTION BOX. CONTRACTOR TO VERIFY ALL CABLE COUNTS AND NUMBER OF PATCH PANELS REQUIRED. GROUP DATA OUTLETS TOGETHER WITH POWER OUTLETS (WHERE APPLICABLE). REFER TO "EP" SERIES SHEETS FOR POWER OUTLET LOCATIONS. FOR ALL OUTLETS INSTALLED IN ARTS/MUSIC/DRAMA AREAS, CLASSROOMS, LABS, MISC. LEARNING AREAS, OFFICES AND OTHER ACOUSTICALLY-RATED PARTITIONS (AS INDICATED ON ARCHITECTURAL DRAWINGS): MAINTAIN A MINIMUM OF 12 INCHES SEPARATION BETWEEN OUTLETS ON OPPOSITE SIDES OF PARTITION. PROVIDE ACOUSTICAL OUTLET BACKER PUTTY (AS MANUFACTURED BY KINETICS NOISE CONTROL, OR EQUAL). PUTTY PADS SHALL MAINTAIN ACOUSTICAL RATINGS PER ASTM C 919 AND ASTM E 497, AND BE TESTED TO UL 263 (ASTM E119) AND UL 1479 (ASTM E814) STANDARDS.
ST
A.
TRACK 156
WAP
BLEACHERS 200A
RG
B
G 6E-O RFB 4
3
RF G 6E-O RFB 4
T11 TYP.
G 6E-O RFB M4
RE
101B T / A3
RJ
Addendum 004
T18
FIL
REVISIONS
TYP.
DS
RD
DS
T24
4
02/05/16
ADDENDUM #02
5
02/15/16
ADDENDUM #04
TYP. WAP
T28
KEY PLAN - NTS
TYP.
3
RB DRAWN BY
RA
CSK/MAD
REVIEWED BY
R2.1
AREA C
GR
EXISTING DATE
R2
02.15.2016
PROJECT NO:
R1.8 A
14-0424.002
DRAWING NAME
MATCH LINE
LEVEL 1 TECHNOLOGY SYSTEMS PLAN AREA A
AREA B AREA A
A3
1
2
3
LEVEL 1 TECHNOLOGY SYSTEMS PLAN - AREA A SCALE: 1/8" = 1'-0"
0'
4
5
4'
8'
16'
NORTH
INE CH L MAT
2/15/2016 2:10:03 PM
NORTH
SHEET NO.
T101A 6
1
2
3
4
5
6
GENERAL NOTES A. SPECIFIED DEVICE MOUNTING ELEVATIONS SHALL BE COORDINATED WITH OTHER DEVICE MOUNTING HEIGHTS UNLESS OTHERWISE NOTED. FOR EXAMPLE, DEVICES SPECIFIED AT 18" AFF SHALL MATCH THE STANDARD MOUNTING HEIGHT FOR POWER RECEPTACLES & TELECOM OUTLETS. DEVICES SPECIFIED AT 48" AFF SHALL MATCH THE STANDARD MOUNTING HEIGHT FOR LIGHT SWITCHES ETC. B. ALL JUNCTION BOXES SHALL BE PROVIDED WITH A COVER UNLESS OTHERWISE NOTED. WHERE RAISED COVERS ARE SPECIFIED, MATCH COVER DEPTH TO WALL THICKNESS. WHERE JUNCTION BOXES ARE MOUNTED AT OR ABOVE FINISHED CEILING HEIGHT, INSTALL BOX WITH OPEN SIDE (OR SCREW COVER SIDE) FACING DOWN. C. PROVIDE A NYLON BUSHING ON ALL CONDUIT STUBS AND NONTERMINATED CONDUIT ENDS TO PROTECT WIRE PULLS. D. SEAL ALL PENETRATIONS THROUGH WALLS, FLOOR, CEILINGS AND ROOF PER ARCHITECTURAL SPECIFIED REQUIREMENTS. SEAL SHALL MATCH THE FIRE RATING OF EACH PENETRATION LOCATION. E. ALL CONDUITS FOR SPECIAL SYSTEMS SHALL BE STEEL, THIN-WALL ELECTRICAL METALLIC TUBING (TYPE EMT) UNLESS OTHERWISE NOTED OR PREVIOUSLY APPROVED VIA FORMAL RFI. UNDER NO CIRCUMSTANCES SHALL FLEXIBLE CONDUITS BE USED FOR PATHWAYS INDICATED ON THIS SHEET. F. POWER OUTLETS (LABELED "P" ON DIAGRAMS) ARE SHOWN FOR COORDINATION/REFERENCE PURPOSES ONLY. PATHWAYS FOR POWER OUTLETS ARE NOT INDICATED ON THIS SHEET. PROVIDE ADDITIONAL, DEDICATED PATHWAYS FOR POWER AS NEEDED. G. JUNCTION AND/OR PULL BOXES INDICATED HEREIN ARE FOR THE PURPOSE OF IDENTIFYING END POINTS ONLY. THE CONTRACTOR SHALL PROVIDE ADDITIONAL PULL BOXES AS NECESSARY TO ENSURE THAT NO SECTION OF A CONDUIT RUN EXCEEDS 100 FEET IN LENGTH OR CONTAINS MORE THAN QTY(2) NINETY-DEGREE TURNS. H. CONDUIT SIZES IDENTIFIED HEREIN REPRESENT STANDARD "TRADE SIZES" AND ARE THE MINIMUM SIZE SPECIFIED FOR THE CABLING DESIGN PARAMETERS. I. CONDUIT ROUTING IS AT THE CONTRACTOR'S DISCRETION. J. PROVIDE NYLON PULL STRINGS IN ALL CONDUITS WITH PULL RINGS AT BOTH ENDS. K. PROVIDE A MEASURING TRACER WIRE IN ALL CONDUITS. L. ALL CONDUIT TURNS SHALL BE "SWEEP" TYPE, NO BEND FITTINGS ARE PERMITTED.
5
E (1)3/4" EMT (EACH) GYMNASIUM #B100 J4 J J
J S
J
S1
S S1
S S1
OVERHEAD COUNT FILL SPEAKER (ZONE 3)
NORTH BLEACHER FILL SPEAKER (ZONE 1)
MICROPHONE & ALS ANTENNAS
PULL BOX J J5
S S2
S
J6
S S1
S1 SOUTH BLEACHER FILL SPEAKER (ZONE 2)
(1)1-1/4" EMT
PA #B102 (1)1" EMT
ARCHITECT
OF
5
E
E
TO
1. REFER TO DETAIL A5 ON SHEET T504 FOR BOX MOUNTING HEIGHT AND INTERNAL DEVICE CONFIGURATION. MOUNT BOX IN PARTITION WALL WITH ACCESS COVER/DEVICE SIDE FACING AWAY FROM WALL. PROVIDE DUPLEX POWER RECEPTACLE AND MOUNT SIDEWAYS INSIDE BOX. COORDINATE FINAL LOCATION WITH ALL OTHER DISCIPLINES PRIOR TO INSTALLATION.
82984
R
J1
PR
D
JOHN F. HECK IV
SHEET KEYNOTES
P
A S
5 A/V RACK
E O F T EX
AT
G
SS
R
J6
J
D
J
J
E
J6
IS T E R G IO N A L E N
EE
J6
J6
IN
J6
ST
STRUCTURAL CEILING
John Heck 2016.02.15 15:02:46-07'00'
PROJECT J6 J
AUDIO INPUT PANEL (1)3/4" RNC
SCORE KEEPER FLOOR BOX
(1)1-1/4" RNC (FOR A/V)
A/V PATHWAY DIAGRAM: GYMNASIUM
D1
SCALE: NO SCALE
ZONE 1
A/V PATHWAY DIAGRAM SYMBOLS LEGEND
C
NORTH BLEACHER FILL SPEAKER (ZONE 1) S
ANTENNA SPLITTER
1
WIRELESS MICROPHONE Rx1
P
POWER JUNCTION BOX, OUTLET BOX (REFER TO EP SHEETS)
J
AUDIOVISUAL JUNCTION/PULL BOX (REFER TO T SHEETS)
LV
LOW VOLTAGE JUNCTION/PULL BOX
TO
TELECOM OUTLET VOICE/DATA
S
LOUDSPEAKER RECESSED FLUSH IN CELING
ZONE 2
CONDUIT STUB WIRELESS MICROPHONE Rx2
WIRELESS MICROPHONE ANTENNAS
SOUTH BLEACHER FILL SPEAKER (ZONE 2) A/V EQUIPMENT RACK AUDIO DSP
WIRELESS MICROPHONE Rx3
S
AUDIO AMPLIFIER
200 Longhorn Street Vega, TX 79092
VEGA ISD HIGH SCHOOL
J3 P A/V TO
FLOOR
1
J J4 LINE
5 WIRELESS MICROPHONE Rx4
LINE 70V
LINE LINE
INPUT PANEL 1
S CEILING SPEAKERS TAP AT 60W
L
2
LINE
M
J2 J
OVERHEAD COUNT FILL SPEAKER (ZONE 3)
AUDIO AMPLIFIER
MIC
MIC
B
ZONE 3
R
5
5 SUMMING ADAPTER
Addendum 004
INPUT PANEL 2 MIC J3
LINE
M
5
ASSISTIVE LISTENING TRANSMITTER
MIC
L
SUMMING ADAPTER
5
02/15/16
ADDENDUM #04
AUDIO
MIC
MIC IN 6
AUX IN
REVISIONS
5
ALS ANTENNA
RACK CONNECTION PANEL
R
J J3
L
L/R AUDIO
R
RECORD OUT
AUDIO OUT ETHERNET SWITCH
DRAWN BY
NETWORK A/V CONTROL
REVIEWED BY DATE PROJECT NO: A/V CONTROL PROCESSOR
TOUCH PANEL
A
02.15.2016 14-0424.002
DRAWING NAME
2/15/2016 2:10:15 PM
AUDIO-VISUAL DIAGRAMS
SOUND SYSTEM FUNCTIONAL DIAGRAM: GYM - A/V SYSTEM TYPE A
A1
SHEET NO.
SCALE: NO SCALE
T601 1
2
3
4
5
6
1
2
3
4
5
6
GENERAL SHEET NOTES 4
5.1
5
Z Y.9 E
CLASSROOM 146
SPRINKLER SYSTEM PIPING AND SPRINKLER HEAD LOCATIONS ARE THE RESPONSIBILITY OF THE FIRE PROTECTION CONTRACTOR. FIELD COORDINATION DURING CONSTRUCTION AND WITH OTHER TRADES SHALL BE NECESSARY PRIOR TO INSTALLATION.
D.
ALL ROOM OCCUPANCIES ARE CLASSIFIED AS LIGHT HAZARD UNLESS OTHERWISE NOTED.
X
W.2 W.1 W
SHEET KEYNOTES
IDF 141
3
1. 2.
U
3
3. 4.
CLASSROOM 136
5. 6.
AT
E O F T EX
102840
OF
5
L
I C E N S E E SS G IO N A L E N
Abbas 2016.02.15 13:21:11-07'00'
S
20
A
ABBAS SHIRIAN PR
T
LAB 135
D
7.
ARCHITECT
S
SPEC ED 137
LEVEL 1 FLOOR CONTROL ASSEMBLY. REFER TO DETAIL C5/FX501. FIRE PROTECTION MAINS SIZED AND CONTINUED BY FIRE PROTECTION CONTRACTOR. THIS AREA ORDINARY HAZARD GROUP 1 OCCUPANCY. PROTECT THE TOP OF THE ELEVATOR SHAFT(S) WITH A FIRE SPRINKLER HEAD, FED FROM A CONTROL ASSEMBLY. REFER TO DETAIL C5/FX501. 6" FIRE PROTECTION DOWN TO BASEMENT. SPRINKLER ALARM VALVE , SEE DETAIL D5/FX501. CONNECT NEW 6" TO EXISTING RISER AND MODIFY EXISTING RISER AS NEEDED TO INSTALL NEW SPRINKLER ALARM VALVE FOR THE NEW ADDITION. PROVIDE HIGH TEMPERATURE SPRIRKLER HEAD AS REQUIRED.
R
BOYS 144
V
STOR 137A
3
C.
D
ELEC 150
CORRIDOR 138
COORDINATE FIRE SPRINKLER SYSTEM PIPING WITH GENERAL CONTRACTOR AND OTHER TRADES AND PROVIDE NECESSARY OFFSETS TO AVOID CONFLICTS AND TO MAINTAIN REQUIRED EQUIPMENT ACCESS AND SERVICE ABILITY.
EE
GIRLS 145
B.
Y
CLASSROOM 148
CLASSROOM 147
REFER TO ARCHITECTURAL DRAWINGS FOR LOCATION OF FIRE RATED AND/OR SMOKE RATED WALLS AND ASSEMBLIES. PIPING PENETRATIONS OF FIRE, SMOKE AND FULL HEIGHT WALLS SHALL BE CAULKED AIR-TIGHT TO THE ADJACENT STRUCTURE BY MEANS OF U.L. APPROVED FIRE SYSTEM.
IN
CLASSROOM 149
A.
ST
3
PROJECT
R T
LAB 131
CORRIDOR 138
CLASSROOM 132
M L
T
12 J STOR 130B
2448
XRB
6
STOR 3 125A
2472
H
3
RR 130A
STOR 128B
2472
STOR 128A
2472
CLASSROOM 129
LIFESKILLS 130
G.9 RT
MAINTENANCE A135
RS
2448
C
STOR A134
MEDIA CENTER 125
CONCESSION 127
RR 6" FP
G 5
ELEC A133.2
CORRIDOR 110 STOR 123A
COMPUTER LAB 121 GIRLS 119
BOYS 118
RV
FAM RR 116
4
~
RN CLASSROOM 122
5
FILES 113
RECEPTION 103
STAGE A124
STOR 111
RG
3
C
3
TRACK 156
PRINC 105
GYMNASIUM B100
LOUNGE 109A
STOR 164
Addendum 004
PROP STOR A125
B
VEST 100
VEST 101
RD
RE
RF
WORKROOM 109
ISS 107
AUDITORIUM A119
RJ
STOR 122C
3
STAIR 2 169
RM
RK
CONF 103A
STUDENT COMMONS 102
E
D.2 D
FP
~ ~ ELEV 721
6" FP
6" FP
3
B
CORRIDOR A132
FP
OFFICE 115
RCRC
RU
2
~
2" FP
F
7
FP
2
JANITOR 120
KILN 123B
3
ELEC 117A ~
RE SCO ER P KEE
RP
1
3 FILM
RQ
FP
R1.8 R2
ART 123
WARMING KITCHEN 128 3
R2.1
REVISIONS
A RB 6.5
7
810 9
11
131415
5
02/15/16
ADDENDUM #04
16
DRAWN BY
Author
REVIEWED BY
R6
AREA C
Approver
EXISTING DATE
R3
LEVEL 1 ABOVE
R2.9
02.15.2016
PROJECT NO:
14-0424.002
DRAWING NAME
MATCH LINE
LEVEL 1 FIRE PROTECTION PLAN
1.9 0.5
ADDENDUM #02
R9 R5
2
1
02/05/16
KEY PLAN - NTS
R8.1 R7R8
A
4
8.8
RA
FILM
200 Longhorn Street Vega, TX 79092
3
Q P N
CLASSROOM 134
STOR/PREP 3 133
VEGA ISD HIGH SCHOOL
MECH 154
AREA B AREA A
A3
1
2
3
LEVEL 1 FIRE PROTECTION PLAN SCALE: 1/16" = 1'-0"
0'
4
5
8'
16'
32'
NORTH
INE CH L MAT
2/15/2016 12:59:17 PM
NORTH
SHEET NO.
FX101 6
1
2
3
4
5
6
TO SPRINKLERS N.C. OS&Y CHECK VALVE BY PASS
WATER PRESSURE GAUGE
5
PRESSURE SWITCH GALV. PIPE AND FITTINGS (TO ALARM)
POST INDICATOR VALVE ASSEMBLY (PIV) WAFER ENDS, UL LISTEDN AND/OR FM APPROVED, WITH SUPERIVISORY SWITCH. MFR: "GEM" MODEL F750
5
RETARD CHAMBER
DRAIN FROM WATER MOTOR GONG
SUPERVISORY SWITCH
FULL SIZE 4'' (10 CM) FLANGED CHECK VALVE
WRECH
4 X 2 (10 X 6.4 CM) TWO WAY F.D. CONN., 45 DEG. PATTERN WHEN MORE THAN 24'' (61 CM) ABOVE GRADE
FLEXIBLE CONDUIT TARGET WINDOW FP
FINISHED GRADE
IN CEILING SPACE
D 4'' GALV. (10 CM)
12" INSTALL FLANGED TAPER REDUCER WHEN REDUCTION IN SIZE IS REQUIRED 3" MINIMUM OR 6" MAXIMUM TO TOP OF SLEEVE
FEBCO MODEL 880V REDUCED PRESS. BACKFLOW PREVENTER OR APPROVED EQUAL.
2" BLUE DETECTABLE WARNING TAPE
SLEEVE BONNET
D
DUCTILE IRON PIPE DUCTILE IRON FLANGE AND SPIGOT PC
SEE AIR GAP DRAIN ASSEMBLY DETAIL (SIDE VIEW) SLEEVE
NON-RISING STEM GAGE VALVE
2" GALV.
PIPE SUPPORT
D
MIN. 4" MAX. 8"
D
2" VANE-TYPE WATER FLOW SWITCH 1 " AIR GAP
GRADE
P8 FLOOR SINK
RODS COATED WITH ASPHALT FINISH GRADE
DRAIN TO OUTSIDE
A
FIRE SUPPLY ENTRANCE
D4
SCALE: 1/4" = 1'-0"
CAST IRON PIPE RODS COATED W/ ASPHALT
INSTALL PER N.F.P.A. 24 & N.F.P.A. 1 3 NOTE: TIE RODS WITH THRUST BLOCK ARE REQUIRED.
POST INDICATOR VALVE
102840 I C E N S E E SS G IO N A L E N
OF
D2
E O F T EX
UNDISTURBED EARTH
L
CLOSE TO FLOOR
CONCRETE SPLASH BLOCK
PR
SUPPORT VALVE ON UNDISTURBED EARTH OR CONCRETE BLOCKS
3'' (7.6 CM) MIN. OR 6'' (15.2 CM) MAX. TO TOP OF SLEEVE. FILL WITH NON HARDENING MASTIC
INSPECTORS TEST DRAIN
AT
ABBAS SHIRIAN
THRUST BLOCK INSTALL PER NFPA-24 NOTE: TIE RODS WITH THRUST BLOCK ARE REQUIRED
D
Abbas 2016.02.15 13:21:04-07'00'
PROJECT
D.I. FLG. & SPIGOT PC.
THRUST BLOCK
SCALE: 1/4" = 1'-0"
SCALE: 1/4" = 1'-0"
ALARM VALVE PIPING WITH RPBFP (TYPICAL)
A1
FLOOR CONTROL ASSEMBLY SEE DETAIL C5/FX501
SPRINKLER PRE-ACTION ALARM VALVE SCALE: 1/4" = 1'-0"
ROOF
FIRST FLOOR
C
UL/FM CHECK VALVE
PRESSURE GAUGE
INDICATING TYPE FLOOR CONTROL VALVE WITH SUPERVISORY SWITCH
WATERFLOW SWITCH FEED MAIN TO WET PIPE FIRE SPRINKLER SYSTEM
6" SIGHT GLASS
BUILDING WALL 48" AFF LOCKING A.P.
FP FP
RISER
TOP OF ELEVATOR
FP
SEE DETAIL D1/FX501
5
FLOOR CONTROL ASSEMBLY SEE DETAIL C5/FX501
UNION WITH CORROSION RESISTANT ORIFICE GIVING FLOW EQUIVALENT TO SMALLEST SPRINKLER ORIFICE IN THE SYSTEM
FIRST
BASEMENT FLOOR
FP
6"
B5
POST INDICATOR VALVE SEE DETAIL D4/FX501
FDC
SCALE: 1/4" = 1'-0"
BASEMENT
FIRE DEPARTMENT CONNECTION
B
FIRE SYSTEM FLOOR CONTROL VALVE
BOTTOM OF ELEVATOR
SPRONKLER ALARM VALVE DETAIL D5/FX501
BFP
TEST VALVE TO DRAIN
FLOOR
6"
BUILDING WALL
SECTIONAL DRAIN VALVE
200 Longhorn Street Vega, TX 79092
C5
SCALE = NONE
VEGA ISD HIGH SCHOOL
D1
ARCHITECT
S
12" A.F.G.
AIR GAP DRAIN & FUNNEL
2" DRAIN
WATER SERVICE LINE
UNDISTURBED EARTH
SEAL WALL PENETRATION WATERTIGHT
%%129'' (1.25 CM) BALL DRIP
FILL W/ NONHARDENING MASTIC
TERMINATE IN CODE COMPLAINT MANNER GROUND FLOOR
O.S. & Y VALVE IN/ELECTRIC MONITOR SWITCH
R
SLEEVE - FILL WITH NON-HARDENING MASTIC
DRAIN LINE
O.S. & Y VALVE IN/ELECTRIC MONITOR SWITCH REDUCED PRESSURE BACKFLOW PREVENTION ASSEMBLY
D
EXTERIOR WALL
ALARM CHECK VALVE
EE
INSPECTORS TEST VALVE
ALARM TEST VALVE (N.C.)
IN
FIRE SPRINKLER SUPPLY LINE
RUN TO FIRE ALARM CONTROL PANEL
ALARM SHUTOFF VAVLE & CHECK VALVE (N.0.) WITH ELECTRICAL MONITOR SWITCH SIGHT GLASS
ST
E
FLOOR
W 6"
FP BUILDING WALL
6" WATER ENTRY THRU FOOTING PER D2/FX501
Addendum 004 5 REVISIONS
B1
FIRE PROTECTION RISER
5
02/15/16
ADDENDUM #04
SCALE: NONE
DRAWN BY
SP
REVIEWED BY
AS
DATE
02.15.2016
PROJECT NO:
14-0424.002
DRAWING NAME
A
2/15/2016 12:59:19 PM
FIRE PROTECTION DETAILS
SHEET NO.
FX501 1
2
3
4
5
6
1
2
3
4
5
6
GENERAL SHEET NOTES A. B. C. D. E. F.
SEE SHEET E603 FOR FIRE ALARM RISER DIAGRAM AND ADDITIONAL INFORMATION. REFER TO SHEET SERIES "EP" FOR ELECTRICAL ROOM EQUIPMENT LAYOUTS AND EQUIPMENT SIZES. REFER TO SHEET SERIES "C", "AS", "M" AND "P" FOR OTHER UTILITIES WITHIN ROUTING PATH OF ELECTRICAL RACEWAYS. REFER TO SHEET E601 FOR ELECTRICAL EQUIPMENT, CONDUIT SIZE AND ADDITIONAL INFORMATION ON ELECTRICAL DISTRIBUTION SYSTEM. REFER TO SHEET SERIES "T" FOR MDF AND IDF ROOMS, EQUIPMENT LAYOUTS AND EQUIPMENT SIZES. CONTRACTOR WILL REFER TO "C" SHEET SERIES FOR OTHER NEW AND EXISTING UTILITIES. CONTRACTOR WILL COORDINATE THE INSTALLATION OF ANY UTILITIES SHOWN ON THIS SHEET PRIOR TO COMMENCEMENT OF ANY WORK FOR BEST LOCATION OF THESE UTILITIES.
E
SHEET KEYNOTES
ES04
UG
P
OH
EX
P
NEW AG BUILDING
EX
ES09
CT
T02
UT
EXISTING AG BUILDING
OF
ES08
E
E
ES07
82984
R
D
PR
ES06
JOHN F. HECK IV G
SS
R
UG
D
P
A S
EX
E O F T EX
AT
E
ES03
ARCHITECT
IS T E R G IO N A L E N
EE
ES02
APPROXIMATE LOCATION OF FIRE ALARM CONTROL PANEL (FACP). REFER TO SHEET E603 FOR ADDITIONAL INFORMATION. REFER TO SHEET SERIES "EP" FOR ELECTRICAL ROOMS AND EQUIPMENT LAYOUTS. POLE MOUNTED LUMINAIRE. REFER TO POLE BASE DETAIL D5 ON SHEET E501. PROVIDE (2)#6 & 1#10 GND. IN 1" CONDUIT. EXTEND THESE CONDUCTORS TO EACH POLE ON THE CIRCUIT INDICATED AND HOMERUN. CIRCUIT WILL BE ROUTED THROUGH A TIME CLOCK LOCATED IN THE SAME ELECTRICAL ROOM AS PANEL SERVING LUMINAIRE. REFER TO SHEET AD101 FOR DEMOLITION INFORMATION ON SIDE OF BUILDING OR ON TOP. ALL LIGHTING WILL BE REMOVED. EXISTING CIRCUIT WILL BE REMOVED BACK TO SOURCE OR NEXT LUMINAIRE DEVICE REMAINING ON EXISTING CIRCUIT. REMOVE CIRCUITS SERVING MECHANICAL UNIT BEING REMOVED BACK TO SOURCE ALONG WITH CONDUIT. REFER TO SHEET AD101 FOR INTERIOR DEMOLITION INFORMATION. EXISTING LUMINAIRES WILL BE REMOVED IN DEMOLITION AREA. EXISTING CIRCUIT WILL REMAIN AND BE REVISED IN NEW DESIGN. REFER TO SHEET EL101B FOR ADDITIONAL INFORMATION. REFER TO SHEET MD101D FOR MECHANICAL UNIT DEMOLITION/REMOVAL. REMOVE CIRCUIT, CONDUCTOR AND RACEWAY PATH BACK TO SOURCE. PROVIDE POWER FOR IRRIGATION CONTROLLER AND HEAT TAPE. LOCATION OF ACTUAL EQUIPMENT TO BE VERIFIED WITH ARCHITECT, ARCHITECTURAL SITE PLAN, AND LANDSCAPE DOCUMENTS TERMINATE TO CONTROLLER AND HEAT TAPE PER EQUIPMENT INSTALLER DIRECTION.
IN
ES01
ST
5
John Heck 2016.02.15 13:46:54-07'00'
PROJECT
S4L1
EX
ES04
S4L1
S4L1
S4L1
PRE-K (METAL BUILDING)
H1B - 1
(MEAS. 1062.39')
S4L1
(MEAS. 1059.76')
P
TYP.
TECHNOLOGY SHEET KEYNOTES
BID LOT NO.4
C
EXISTING BUILDING
S4L2
MUSIC
ES02 ES04
UG
F
H1B - 3
ES01
P
ES03
T01. QTY. (2) 4" UNDERGROUND CONDUIT PATHWAY SCH 80 SOLID WALL. FROM IDF 141 TO STORAGE 103 IN FUTURE AG BUILDING. T02. 4'-0" X 4'-0" HAND-HOLE WITH 4" STUBS FOR SERVICE PROVIDER USE. PROVIDE APPROPRIATE DRAINAGE FOR HANDHOLE. GROUND AND BOND PER HAND-HOLE MANUFACTURES RECOMMENDATIONS. T03. PROVIDE CONCRETE DUCTBANK ENCASEMENT FOR CONDUIT PATHWAY TO BE TRAFFIC RATED. PROVIDE TRACER WIRE.
EX
TYP.
S4L2
5
BUS
FF
L1A - 55,57
J
200 Longhorn Street Vega, TX 79092
OH
ES03
T01
UG
S UG
P
VEGA ISD HIGH SCHOOL
T03
CT
ES09
UT 5
ES08
MSB
R OH X S X
S4L2
S
ES02 F
ES07 ES08 F
J
ES02
4TH STREET
B
BID LOT NO.3
RC RC
ES06
NEW CONSTRUCTION
ES08
Addendum 004 ES03
H1A - 1
TYP.
S4L2
5
S4L2
S4L2
S4L2
S4L2
REVISIONS 5
S4L2
ES04
4
02/05/16
ADDENDUM #02
5
02/15/16
ADDENDUM #04
(MEAS. 1058.96')
(MEAS. 83.00')
HH
(MEAS. 83.00')
LONGHORN STREET
DRAWN BY
Author
REVIEWED BY DATE
JMM 02.15.2016
PROJECT NO:
14-0424.002
DRAWING NAME
A NORTH
SCALE: 1" = 50'-0"
0'
25'
50'
100'
2/15/2016 8:42:07 AM
A1
ELECTRICAL SITE PLAN
ELECTRICAL SITE PLAN
SHEET NO.
ES101 1
2
3
4
5
6
1
2
3
4
5
6
GENERAL SHEET NOTES 5
E
A3 / EL100B
A. ALL EXIT SIGNS, TYPES "E", "E2" OR "EG", WILL BE CONNECTED TO CIRCUIT SERVING THE ROOM THEY ARE LOCATED IN AND FROM NO OTHER CIRCUIT. B. REFER TO SHEET E701 FOR ELECTRICAL LUMINAIRE SCHEDULE. C. REFER TO SHEET SERIES "EP" FOR ELECTRICAL ROOMS AND ELECTRICAL EQUIPMENT LAYOUT. D. REFER TO SHEET E604 FOR LIGHTING DIAGRAMS AND SEQUENCE OF OPERATION. E. REFER TO DETAILS C5 AND D3 ON SHEET E501 FOR LUMINAIRE MOUNTING. F. REFER TO ARCHITECTURAL SHEET SERIES "AE" FOR ADDITIONAL CEILING GRID MOUNTING SUPPORT INFORMATION. ALL LUMINAIRES WILL BE SECURELY SUPPORTED SEPARATELY FROM CEILING GRIDS TO CEILING STRUCTURE. G. REFER TO ARCHITECTURAL SHEETS FOR EXTERIOR LIGHTING ELEVATIONS. H. ALL EXTERIOR BUILDING LUMINAIRES WILL BE ROUTED THROUGH A TIME CLOCK AND CONTACTOR LOCATED IN THE ELECTRICAL ROOM WHERE THE PANEL FEEDING THOSE LUMINAIRES IS LOCATED. REFER TO DIAGRAM E3 ON SHEET E605 FOR ADDITIONAL INFORMATION. THE EXTERIOR BUILDING LUMINAIRES AND SITE LUMINAIRES MUST BE CONTROLLED SEPERATELY. I. CORRIDOR LUMINAIRES WILL BE ROUTED THROUGH A TIME CLOCK AND CONTACTOR LOCATED IN THE ELECTRICAL ROOM WHERE THE PANEL FEEDING THOSE LUMINAIRES IS LOCATED. REFER TO DIAGRAM C3 ON SHEET E605 FOR ADDITIONAL INFORMATION. J. ALL LUMINAIRES IN DASHED AREA WILL BE CONNECTED TO CIRCUIT INDICATEDUNLESS OTHERWISE NOTED.
ARCHITECT
ST
S
B L100 E / A3
A
D
E
IS T E R G IO N A L E N
IN
OF
E
SS
EE
R
E
PA B102
82984 G
R
JOHN F. HECK IV PR
D
E O F T EX
AT
John Heck 2016.02.15 13:47:08-07'00'
KEYNOTES OS K
EL01
EM
EL02
EL13 EG H1A - 18
C6L HALL C6L B100A
EL03
EL04
EL02 5
3
EL12
BL EL13
DIGITAL "KEYPAD" LIGHTING CONTROL STATION CONSISTING OF ONE (OR MORE) 1-GANG PUSHBUTTON DEVICES WITH MULTIPLE ENGRAVED "SCENE RECALL" BUTTONS FOR CONTROL OF PRE-PROGRAMMED LIGHTING WITHIN ROOM. REFER TO CONTROL DIAGRAMS AND SEQUENCE OF OPERATION ON SHEET E604. ONE SWITCH; SWITCH TYPE AS INDICATED. WILL CONTROL THE LUMINAIRES IN ROOM. WALL-MOUNTED OCCUPANCY SENSOR, WATT STOPPER PW-100 OR APPROVED EQUAL. LOCATE PER MANUFACTURER'S RECOMMENDATIONS. SHOWN HERE FOR BID PURPOSES. REFER TO SHEET E604 FOR WIRING DIAGRAM AND ADDITIONAL INFORMATION ON SENSOR TYPE. CEILING-MOUNTED SENSOR, WATT STOPPER DT-355 OR APPROVED EQUAL. LOCATE PER MANUFACTURER'S RECOMMENDATIONS. SHOWN HERE FOR BID PURPOSES. DIGITAL "KEYPAD" LIGHTING CONTROL STATION WHICH WILL ONLY CONTROL MEZZANINE AREA LIGHTING. LABEL SWITCH "SEATING AREA". REFER TO CONTROL DIAGRAMS AND SEQUENCE OF OPERATION ON SHEET E604. ONE SWITCH; A KEYED MOMENTARY OVERRIDE SWITCH. THIS SWITCH WILL CONTROL CORRIDOR LIGHTING. IT WILL ALSO PROVIDE OVERRIDE OF LIGHTING BETWEEN 11 PM AND 5 AM. IF LIGHTING IS TURNED ON DURING THE NIGHT, THE LIGHTING WILL AUTOMATICALLY TURN OFF AFTER 30 MINUTES. LIGHTING WILL SIGNAL WITH A BLINK OF THE LIGHTS (5) FIVE MINUTES BEFORE SHUT DOWN. LABEL SWITCH "CORRIDOR CONTROL".
VEGA ISD HIGH SCHOOL
BL
EL01
BL
EL04 OS
RQ RP
BL
BL
STOR B103
C
EL02 GYMNASIUM B100
3
BL
BL
STAIR 2 169
EL02 EL04 5
OS
RN
BL
EG H1A - 18
STOR B138
EL13
C6L EM
C6L
EL03
K
OS
H1A - 2 RM
HALL B100B
EL01
BL
BL
200 Longhorn Street Vega, TX 79092
PROJECT
EL03
PUMP ROOM B130
RK BL
H1A - 12
K,3
EL13
EL04 HALL B140
B
B L100 E / A3
EL12
OS
EG H1A - 17
A1Sa
EM
RJ RG
5
ALL KEYNOTE NUMBERS HAVE BEEN REVISED ON THIS SHEET
RF R2.9
Addendum 004 REVISIONS 4
02/05/16
ADDENDUM #02
5
02/15/16
ADDENDUM #04
KEY PLAN - NTS N.T.S.
DRAWN BY AREA C
EXISTING
REVIEWED BY DATE
R2.1
LEVEL 1 ABOVE MATCH LINE
A
KIS JMM 02.15.2016
PROJECT NO:
14-0424.002
DRAWING NAME
LOWER LEVEL LIGHTING PLAN AREA A
AREA B AREA A
A3
LOWER LEVEL LIGHTING PLAN - AREA A SCALE: 1/8" = 1'-0"
0'
1
2
3
4
5
4'
8'
16'
NORTH
INE CH L MAT
2/15/2016 8:44:21 AM
NORTH
SHEET NO.
EL100A 6
1
2
3
4
5
6
GENERAL SHEET NOTES 5
E
A. ALL EXIT SIGNS, TYPES "E", "E2" OR "EG", WILL BE CONNECTED TO CIRCUIT SERVING THE ROOM THEY ARE LOCATED IN AND FROM NO OTHER CIRCUIT. B. REFER TO SHEET E701 FOR ELECTRICAL LUMINAIRE SCHEDULE. C. REFER TO SHEET SERIES "EP" FOR ELECTRICAL ROOMS AND ELECTRICAL EQUIPMENT LAYOUT. D. REFER TO SHEET E604 FOR LIGHTING DIAGRAMS AND SEQUENCE OF OPERATION. E. REFER TO DETAILS C5 AND D3 ON SHEET E501 FOR LUMINAIRE MOUNTING. F. REFER TO ARCHITECTURAL SHEET SERIES "AE" FOR ADDITIONAL CEILING GRID MOUNTING SUPPORT INFORMATION. ALL LUMINAIRES WILL BE SECURELY SUPPORTED SEPARATELY FROM CEILING GRIDS TO CEILING STRUCTURE. G. REFER TO ARCHITECTURAL SHEETS FOR EXTERIOR LIGHTING ELEVATIONS. H. ALL EXTERIOR BUILDING LUMINAIRES WILL BE ROUTED THROUGH A TIME CLOCK AND CONTACTOR LOCATED IN THE ELECTRICAL ROOM WHERE THE PANEL FEEDING THOSE LUMINAIRES IS LOCATED. REFER TO DIAGRAM E3 ON SHEET E605 FOR ADDITIONAL INFORMATION. THE EXTERIOR BUILDING LUMINAIRES AND SITE LUMINAIRES MUST BE CONTROLLED SEPERATELY. I. CORRIDOR LUMINAIRES WILL BE ROUTED THROUGH A TIME CLOCK AND CONTACTOR LOCATED IN THE ELECTRICAL ROOM WHERE THE PANEL FEEDING THOSE LUMINAIRES IS LOCATED. REFER TO DIAGRAM C3 ON SHEET E605 FOR ADDITIONAL INFORMATION. J. ALL LUMINAIRES IN DASHED AREA WILL BE CONNECTED TO CIRCUIT INDICATEDUNLESS OTHERWISE NOTED.
ARCHITECT
R9 ST
SS
R
D
E
IS T E R G IO N A L E N
EE
G
IN
OF
GIRLS JV B113
E
E
20
82984
R
PR
John Heck 2016.02.15 13:47:21-07'00'
KEYNOTES A1Sa A1Sa
GIRLS VARSITY B111
A1Sa
GIRLS B112
EL04
EL02
A1Sa
EM
EL02 A1Sa
K EG
K
A1Sa
H1A - 6
EL02 EL04
K
EM
EG
FILM ROOM B107
EM A1Sa OS
A L100 E / A3
EL03
A1Sa
RR
A1Sa
EG
EM
A1Sa
EL01 EL06
RQ
ELEC B121
EL08
RP
BL
EL06
EL11
EL02 EM
BL
EL03
EM
EL02 A1Sa
A1Sa
EG
EL02
EM
EM
COACH RR B109
ELEV 714
A1Sa WL L0A - 37
A1Sa A1Sa
EM A1Sa
5
EL31
ELEC B117
A1Sa
EL02
CORRIDOR B106
OS
BL
H1A - 8
EL23 E2
EL13
EL06
H1A - 15
OS
GIRLS COACH B108 A1Sa
EL18 EL23 EL31
REFER TO SHEET EP100B FOR CIRCUIT INFORMATION FOR LUMINAIRE IN ELEVATOR PIT. EXTEND 120V CIRCUIT FROM RECEPTACLE ON EP100B. EXIT SIGN WILL BE MOUNTED WITH ROD SECURELY ATTACHED TO STRUCTURE. BATTERY INVERTER "B0A" WILL BE RATED FOR 4800 VA AND MAXIMUM DIMENSION SIZE OF 40"W x 48"H x 25"D.
RN
A1Sa
EL18 UNIFORM STOR B120
EG
EL02
EL04
EM
BOYS COACH B119
OS
5
EL02
OS
A1Sa
H1A - 4
A1Sa
FILM ROOM B118
RK
STAIR 1 713
BL
A1Sa
RM
H1A - 10
A1Sa
EL03
EL04 OS
EM
EM
BL
A1Sa
A1Sa
5
A1Sa A1Sa
A1Sa
EL04
EG EM
K
A1Sa
EL04
EL04
EL05
BL
OS
EM
RC
EM
EL02
A1Sa
EL04
JANITOR B115
A1Sa
A1Sa
EL04
EL08
EL03
EL04
EM
TRAINING B116
A1Sa
A1Sa
A1Sa
C
OS
OS
EL03
EM
UNIFORM STOR B114 BL
EL02
A1Sa
A1Sa
A1Sa
A1Sa A1Sa
A1Sa
OS
EL04
EM
EL02
RS
EL11
K
A1Sa
5
OS
EG
OS
EM
A1Sa EM
RT
B4 E604
DIGITAL "KEYPAD" LIGHTING CONTROL STATION CONSISTING OF ONE (OR MORE) 1-GANG PUSHBUTTON DEVICES WITH MULTIPLE ENGRAVED "SCENE RECALL" BUTTONS FOR CONTROL OF PRE-PROGRAMMED LIGHTING WITHIN ROOM. REFER TO CONTROL DIAGRAMS AND SEQUENCE OF OPERATION ON SHEET E604. ONE SWITCH; SWITCH TYPE AS INDICATED. WILL CONTROL THE LUMINAIRES IN ROOM. WALL-MOUNTED OCCUPANCY SENSOR, WATT STOPPER PW-100 OR APPROVED EQUAL. LOCATE PER MANUFACTURER'S RECOMMENDATIONS. SHOWN HERE FOR BID PURPOSES. REFER TO SHEET E604 FOR WIRING DIAGRAM AND ADDITIONAL INFORMATION ON SENSOR TYPE. CEILING-MOUNTED SENSOR, WATT STOPPER DT-355 OR APPROVED EQUAL. LOCATE PER MANUFACTURER'S RECOMMENDATIONS. SHOWN HERE FOR BID PURPOSES. COORDINATE WITH TELECOMMUNICATIONS RACK EQUIPMENT AND CABLE TRAY PLACEMENT FOR LUMINAIRE LOCATION. REFER SHEET SERIES "T" FOR TECHNOLOGY DETAILS. REFER TO SHEET SERIES "EP" FOR ELECTRICAL EQUIPMENT LAYOUT IN THIS ROOM. LIGHTING ROOM CONTROLLER(S) FOR LIGHTING CONTROL SYSTEM IN THIS ROOM. REFER TO SHEET E604 FOR WIRING DIAGRAM AND ADDITIONAL INFORMATION ON ROOM CONTROLLER TYPE. CEILING-MOUNTED OCCUPANCY SENSOR, LOCATE PER MANUFACTURER'S RECOMMENDATIONS. SHOWN HERE FOR BID PURPOSES. REFER TO SHEET E604 FOR WIRING DIAGRAM AND ADDITIONAL INFORMATION ON SENSOR TYPE. ONE SWITCH; A KEYED MOMENTARY OVERRIDE SWITCH. THIS SWITCH WILL CONTROL CORRIDOR LIGHTING. IT WILL ALSO PROVIDE OVERRIDE OF LIGHTING BETWEEN 11 PM AND 5 AM. IF LIGHTING IS TURNED ON DURING THE NIGHT, THE LIGHTING WILL AUTOMATICALLY TURN OFF AFTER 30 MINUTES. LIGHTING WILL SIGNAL WITH A BLINK OF THE LIGHTS (5) FIVE MINUTES BEFORE SHUT DOWN. LABEL SWITCH "CORRIDOR CONTROL".
EG
A1Sa OS
K
K
EL02
BOYS B123
EL04
K
B
A1Sa
EL23 A1Sa
H1A - 8 CORRIDOR B132
EL04 EM
OS
GIRLS VISITOR B133 OS
A1Sa A1Sa
A1Sa
A1Sa
EM
EM
EL04
EM
A1Sa
5
K
K
A1Sa
BOYS VISITOR OS B131
EL02
A1Sa
EL02
RF
A1Sa EM
A1Sa
OS
RG
EM
A1Sa
EL03
BL BL EG
EM
RJ
EM A1Sa
A1Sa
A1Sa
EM
EL05
K,3
E2
A1Sa
A1Sa
A1Sa
OS
EL13
EL04
EG
EM K
OS
A1Sa
EM
A1Sa
EM
EL02
OS
EL02
BOYS JV B124
A1Sa
EM
A1Sa
OS
A1Sa
EL02
A1Sa
A1Sa BOYS VARSITY B122
200 Longhorn Street Vega, TX 79092
PROJECT EL01
VEGA ISD HIGH SCHOOL
R3
JOHN F. HECK IV
XRB
R6
R5
D
R8
A S
R7
E O F T EX
AT
EM EM
A1Sa
OS
ALL KEYNOTE NUMBERS HAVE BEEN REVISED ON THIS SHEET
RE A1Sa
A1Sa OS A1Sa
EL04
EL04
Addendum 004 REVISIONS 4
02/05/16
ADDENDUM #02
5
02/15/16
ADDENDUM #04
EM A1Sa
KEY PLAN - N.T.S.
A1Sa
A L100 E / A3
A1Sa
OFFICIALS B128
OFFICIALS RR B129 DRAWN BY REVIEWED BY DATE LEVEL 1 ABOVE
R2.9
A
KIS JMM 02.15.2016
PROJECT NO:
14-0424.002
DRAWING NAME
LOWER LEVEL LIGHTING PLAN AREA B
AREA B AREA A
A3
1
2
3
LOWER LEVEL LIGHTING PLAN - AREA B SCALE: 1/8" = 1'-0"
0'
4
5
4'
8'
16'
NORTH
INE CH L MAT
2/15/2016 8:45:31 AM
NORTH
SHEET NO.
EL100B 6
1
2
3
4
5
6
GENERAL SHEET NOTES 5
R2.9
A3 / EL101B VEST 124
H1B - 2 C6LWE
E
C6L
EL16
A. ALL EXIT SIGNS, TYPES "E", "E2" OR "EG", WILL BE CONNECTED TO CIRCUIT SERVING THE ROOM THEY ARE LOCATED IN AND FROM NO OTHER CIRCUIT. B. REFER TO SHEET E701 FOR ELECTRICAL LUMINAIRE SCHEDULE. C. REFER TO SHEET SERIES "EP" FOR ELECTRICAL ROOMS AND ELECTRICAL EQUIPMENT LAYOUT. D. REFER TO SHEET E604 FOR LIGHTING DIAGRAMS AND SEQUENCE OF OPERATION. E. REFER TO DETAILS C5 AND D3 ON SHEET E501 FOR LUMINAIRE MOUNTING. F. REFER TO ARCHITECTURAL SHEET SERIES "AE" FOR ADDITIONAL CEILING GRID MOUNTING SUPPORT INFORMATION. ALL LUMINAIRES WILL BE SECURELY SUPPORTED SEPARATELY FROM CEILING GRIDS TO CEILING STRUCTURE. G. REFER TO ARCHITECTURAL SHEETS FOR EXTERIOR LIGHTING ELEVATIONS. H. ALL EXTERIOR BUILDING LUMINAIRES WILL BE ROUTED THROUGH A TIME CLOCK AND CONTACTOR LOCATED IN THE ELECTRICAL ROOM WHERE THE PANEL FEEDING THOSE LUMINAIRES IS LOCATED. REFER TO DIAGRAM E3 ON SHEET E605 FOR ADDITIONAL INFORMATION. THE EXTERIOR BUILDING LUMINAIRES AND SITE LUMINAIRES MUST BE CONTROLLED SEPERATELY. I. CORRIDOR LUMINAIRES WILL BE ROUTED THROUGH A TIME CLOCK AND CONTACTOR LOCATED IN THE ELECTRICAL ROOM WHERE THE PANEL FEEDING THOSE LUMINAIRES IS LOCATED. REFER TO DIAGRAM C3 ON SHEET E605 FOR ADDITIONAL INFORMATION. J. ALL LUMINAIRES IN DASHED AREA WILL BE CONNECTED TO CIRCUIT INDICATEDUNLESS OTHERWISE NOTED.
EM C6LWE H1B - 2
EL30 W2LE FL H1B - 2
5
W2L
EL30 W2LE 5
W2L
EL30 W2LE
FL H1B - 2
5
W2L
EL30 W2LE FL H1B - 2
OS
EL10
5
W2L
ARCHITECT
EL30 W2LE
A S
5
W2L
ST
H1A - 20
E O F T EX
AT
OS
KEYNOTES EG
EG
EL16 FLE H1B - 2
BTL EL04
RT
RC RC EL08
BTL
RS
EL08 BTL
EL10
OS
EL10
H1A - 16
BTL
RR
EL12
D1 E604 BTL
BTL
EL13
RQ RP
BTL
EL12
K,3
EG
BTL
BTL
OS
EL10
EL13 A1Sa
H1A - 19
EL16
H1A - 18
BTL
EL24 EL25
EM OS
C
BTL
EL04
EL25 FL H1B - 2
EL30
H1A - 21
BTL
LUMINAIRE WILL BE CONNECTED TO LIGHTING BATTERY INVERTER "B1B" LOCATED IN ELEC 150. REFER TO DETAIL A1 ON SHEET E605 FOR TYPICAL EMERGENCY LIGHTING BATTERY INVERTER DIAGRAM. BID LOT #3. REFER TO SHEET EL102A FOR ADDITIONAL INFORMATION. SHOULD BID LOT #3 BE ACCEPTED, THIS LUMINAIRE WILL BE LOCATED AS INDICATED ON SHEET EL102A. LUMINAIRE WILL BE CONNECTED TO LIGHTING BATTERY INVERTER "B0A" LOCATED IN ELEC 117. REFER TO DETAIL A1 ON SHEET E605 FOR TYPICAL EMERGENCY LIGHTING BATTERY INVERTER DIAGRAM.
EL10
STAIR 2 169
H1A - 14
BTL
BTL
BTL
EL12
RM
A
BTL
BTL
EL24
DIGITAL "KEYPAD" LIGHTING CONTROL STATION WHICH WILL ONLY CONTROL MEZZANINE AREA LIGHTING. LABEL SWITCH "SEATING AREA". REFER TO CONTROL DIAGRAMS AND SEQUENCE OF OPERATION ON SHEET E604. ONE SWITCH; A KEYED MOMENTARY OVERRIDE SWITCH. THIS SWITCH WILL CONTROL CORRIDOR LIGHTING. IT WILL ALSO PROVIDE OVERRIDE OF LIGHTING BETWEEN 11 PM AND 5 AM. IF LIGHTING IS TURNED ON DURING THE NIGHT, THE LIGHTING WILL AUTOMATICALLY TURN OFF AFTER 30 MINUTES. LIGHTING WILL SIGNAL WITH A BLINK OF THE LIGHTS (5) FIVE MINUTES BEFORE SHUT DOWN. LABEL SWITCH "CORRIDOR CONTROL".
EG
OS
H1A - 12
RN
ONE SWITCH; SWITCH TYPE AS INDICATED. WILL CONTROL THE LUMINAIRES IN ROOM. CEILING-MOUNTED SENSOR, WATT STOPPER DT-355 OR APPROVED EQUAL. LOCATE PER MANUFACTURER'S RECOMMENDATIONS. SHOWN HERE FOR BID PURPOSES. LIGHTING ROOM CONTROLLER(S) FOR LIGHTING CONTROL SYSTEM IN THIS ROOM. REFER TO SHEET E604 FOR WIRING DIAGRAM AND ADDITIONAL INFORMATION ON ROOM CONTROLLER TYPE. PROVIDE A HIGH BAY, LINE VOLTAGE, OCCUPANCY SENSOR CAPABLE OF 360 DEGREE VIEWING RANGE AND MOUNTED TO BOTTOM OF JOISTS ABOVE BASKETBALL COURT FINISH FLOOR. WATT STOPPER LMPC-100 OR APPROVED EQUAL. PROVIDE PROPER VIEWING LENS HBL4 SERIES. QUANTITY OF DEVICES SHOWN SHOULD BE VERIFIED WITH MANUFACTURER FOR EXACT QUANTITY AND LOCATION FOR THIS INSTALLATION. SHOWN HERE FOR BID PURPOSES. REFER TO SHEET E604 FOR WIRING DIAGRAM.
A1Sa BTL
H1A - 17
A1Sa EM
BTL
OS
RK
D
E
EE
PROJECT EL02
VEGA ISD HIGH SCHOOL
RU
IS T E R G IO N A L E N John Heck 2016.02.15 13:47:33-07'00'
IN
SS
EL12
EL10
82984 G
EL10
200 Longhorn Street Vega, TX 79092
EL12
OF
XRB
E
E
BLEACHER 200B
R
D
PR
RV
R
JOHN F. HECK IV
BTL
EL25 FL H1B - 2
BTL
BTL A1Sa
RJ
OS
EL10
BLEACHERS 200A
RG
B
W2L
RF
5
H1A - 22
EL30 W2L 5
OS
EL10
EL30
RE
5
EL30
ALL KEYNOTE NUMBERS HAVE BEEN REVISED ON THIS SHEET
W2LE
W2LE
FL H1B - 2
W2L
EG
EL16
5
FL H1B - 2
W2L
EL12
RD
W2LE
5
FLE H1B - 2
EL30
EL30
REVISIONS 4
02/05/16
ADDENDUM #02
5
02/15/16
ADDENDUM #04
W2LE
W2L 5
Addendum 004
FL H1B - 2
KEYPLAN - N.T.S.
W2LE
FL H1B - 2
RB DRAWN BY
RA
REVIEWED BY AREA C
JMM
EXISTING DATE
02.15.2016
PROJECT NO:
A
KIS
14-0424.002
DRAWING NAME
MATCH LINE
LEVEL 1 LIGHTING PLAN - AREA A AREA B AREA A
A3
1
2
3
LEVEL 1 LIGHTING PLAN - AREA A SCALE: 1/8" = 1'-0"
0'
4
5
4'
8'
16'
NORTH
INE CH L MAT
2/15/2016 8:57:11 AM
NORTH
SHEET NO.
EL101A 6
1
2
3
4
5
6
GENERAL SHEET NOTES 5
A3 / EL101C
A3 / EL101C
J
E
AKb STOR 129A
RC
ARLD
A1Fb
ARaD A2 E604
EL01
BL
EL04
EL03
RR 130A
LIFESKILLS 130
ARb
OS 3
OS
EL02 C6L
BL
BL
EL03
EL16
EL16 AKa
a,b
a,b
OS c
EL14
EM
VEST 124 N8CL
N8CL
C6L
C6L
E
C6L
E2
N4CL
EL13
C6L
C6L
EM
N6CL
H1A - 7
C6L
BOYS 118
N8CL
C6L JANITOR 120
N8CL
BL
EL02
N8CL
N8CL
EM
EL13
N8CL
EL13
N8CL N8CL
N8CL
ARb
E2
H1A - 9
H1A - 7 OS
N8CL
TEST STOR 115A
N8CL
N8CL
FILES 113
EL02
E
N8CL
N8CL N8CL
L0A - 28 P4L
C6L
P4L C6L L0A - 28 C6LWW P4L L0A - 28 L0A - 28 P4L
EL20
E
K
EL02
E
EL02 C6L
C6L
P4L L0A - 28
C6L
VEST 101
EL33
K
EL20 C6L
BL
A1Fb EM
EL03
EL04
EL03 EL33
OS
BL
CORRIDOR EM 106
EL34
STOR 111
C6L
C6L
SS
IS T E R G IO N A L E N
John Heck 2016.02.15 13:47:45-07'00'
DIGITAL "KEYPAD" LIGHTING CONTROL STATION CONSISTING OF ONE (OR MORE) 1-GANG PUSHBUTTON DEVICES WITH MULTIPLE ENGRAVED "SCENE RECALL" BUTTONS FOR CONTROL OF PRE-PROGRAMMED LIGHTING WITHIN ROOM. REFER TO CONTROL DIAGRAMS AND SEQUENCE OF OPERATION ON SHEET E604. ONE SWITCH; SWITCH TYPE AS INDICATED. WILL CONTROL THE LUMINAIRES IN ROOM. WALL-MOUNTED OCCUPANCY SENSOR, WATT STOPPER PW-100 OR APPROVED EQUAL. LOCATE PER MANUFACTURER'S RECOMMENDATIONS. SHOWN HERE FOR BID PURPOSES. REFER TO SHEET E604 FOR WIRING DIAGRAM AND ADDITIONAL INFORMATION ON SENSOR TYPE. CEILING-MOUNTED SENSOR, WATT STOPPER DT-355 OR APPROVED EQUAL. LOCATE PER MANUFACTURER'S RECOMMENDATIONS. SHOWN HERE FOR BID PURPOSES. LIGHTING ROOM CONTROLLER(S) FOR LIGHTING CONTROL SYSTEM IN THIS ROOM. REFER TO SHEET E604 FOR WIRING DIAGRAM AND ADDITIONAL INFORMATION ON ROOM CONTROLLER TYPE. CEILING-MOUNTED OCCUPANCY SENSOR, LOCATE PER MANUFACTURER'S RECOMMENDATIONS. SHOWN HERE FOR BID PURPOSES. REFER TO SHEET E604 FOR WIRING DIAGRAM AND ADDITIONAL INFORMATION ON SENSOR TYPE. ONE SWITCH; A KEYED MOMENTARY OVERRIDE SWITCH. THIS SWITCH WILL CONTROL CORRIDOR LIGHTING. IT WILL ALSO PROVIDE OVERRIDE OF LIGHTING BETWEEN 11 PM AND 5 AM. IF LIGHTING IS TURNED ON DURING THE NIGHT, THE LIGHTING WILL AUTOMATICALLY TURN OFF AFTER 30 MINUTES. LIGHTING WILL SIGNAL WITH A BLINK OF THE LIGHTS (5) FIVE MINUTES BEFORE SHUT DOWN. LABEL SWITCH "CORRIDOR CONTROL". ONE SWITCH. WILL CONTROL THE PENDANT MOUNTED LUMINAIRES IN ROOM. LABEL SWITCH "PENDANTS". ONE PROGRAMMABLE TIME CLOCK WITH ROOF MOUNTED PHOTO CELL AND 4 POLE 20A CONTACTOR FOR EXTERIOR BUILDING LIGHTING. REFER TO DETAIL E3 ON SHEET E605 FOR ADDITIONAL INFORMATION. LUMINAIRE WILL BE CONNECTED TO LIGHTING BATTERY INVERTER "B1B" LOCATED IN ELEC 150. REFER TO DETAIL A1 ON SHEET E605 FOR TYPICAL EMERGENCY LIGHTING BATTERY INVERTER DIAGRAM. ONE SWITCH. WILL CONTROL THE PENDANT MOUNTED LUMINAIRES IN THE CENTER OF THE COVES IN THE STUDENT COMMONS AREA. LABEL SWICH "PENDANTS IN COVE" MOUNT EXIT SIGN TO MULLION IN GLAZED STOREFRONT SYSTEM. BRANCH CIRCUIT SHALL BE STANDARD 20-AMP IN 3/4-INCH CONDUIT. TRANSITION TO 3/8-INCH MC CABLING AT THE STOREFRONT GLAZING AREA, AND CONCEL THE MC CABLING INSIDE MULLIONS TO TERMINATE AT THE EXIT SIGN. COORDINATE WITH ARCHITECT PRIOR TO COMMENCING ANY ROUGH-IN WORK. ONE SWITCH. WILL CONTROL THE PENDANT MOUNTED LUMINAIRES OVER RECEPTION DESK. LABEL SWITCH "PENDANTS". LUMINAIRES IN THE DASHED AREA WILL BE CONNECTED TO EXISTING 120V CIRCUIT. EXISTING SWITCH LOCATION WILL BE ADJUSTED/MODIFIED WITH MODIFICATION OF WALLS. EXISTING SWITCH CONTROL WILL BE RECONNECTED FOR CONTROL OF LUMINAIRES IN DASHED AREA. REFER TO DETAIL A1 ON SHEET AE222 FOR ADDITIONAL INFORMATION ON LUMINIARES OVER RECEPTION DESK. LUMINAIRE WILL BE CONNECTED TO LIGHTING BATTERY INVERTER "B0A" LOCATED IN ELEC 117. REFER TO DETAIL A1 ON SHEET E605 FOR TYPICAL EMERGENCY LIGHTING BATTERY INVERTER DIAGRAM. ONE PROGRAMMABLE TIME CLOCK WITH ROOF MOUNTED PHOTO CELL AND 4 POLE 20A CONTACTOR FOR CORRIDOR LIGHTING. REFER TO DETAIL C3 ON SHEET E605 FOR ADDITIONAL INFORMATION. PENDANT OVER RECEPTION DESK WILL BE CONTROLLED WITH TOGGLE SWITCH. REFER TO KEYNOTE EL21 ON THIS SHEET FOR ADDITIONAL INFORMATION. PENDANT IN CENTER OF COVE WILL BE CONTROLLED WITH TOGGLE SWITCH IN RECEPTION 103. REFER TO KEYNOTE EL19 ON THIS SHEET FOR ADDITIONAL INFORMATION.
EM
EL02
5
EL13
EL04
EM C6L
OS
EL02 OS
ISS 107
C6L
WORKROOM 109 ARb ARb
EL04
ARb
EM
PROP STOR A125
EM ARb
EL14
b a
ARb
EL02
EM
ARb
LOUNGE 109A
EL02
ARb a
EL04
5
H1A - 5
OS
a
P21L L0A - 28
ALL KEYNOTE NUMBERS HAVE BEEN REVISED ON THIS SHEET
5 K
b
OS
5
E
C6L
5
EL13 C6L
5
EL13
VEST 100
C6L
C6L
C6L E
K
C6L
H1A - 9
Addendum 004 REVISIONS 4
02/05/16
ADDENDUM #02
5
02/15/16
ADDENDUM #04
EL04 FLE H1B - 2
PRINC 105
C6LWW
EM
EL29 EL30
ARb
TYP.
EL28
STAGE A124
BL
M 112
A1Fb W EM 108 OS
EL03
C6L a NURSE 114 EM
C6LWW
P4L L0A - 28
EL13
W 122A EM A1Fb
BL OS
C6L
E
a a C6L
TYP.
N8CL
AUDITORIUM A119
EL02
M 122B EM A1Fb
OS
H1A - 9
EL29
EL19
EL20 P27L P27L
EL21
EL02
CORRIDOR 110
N8CL
EL21
BVL
OS
C6L
3
C6L
B
EL19
BVL
BVL
H1A - 7
C6L RECEPTION EM C6L 103
EM
EM
BVL
OS
N8CL
OS
EL16
EL32
EM
CONF 103A N8CL
EL04
BVL
BL
ARb
EL02
EL15
BVL
EM
ARb
EL04
3
ARb
K
EL13
H1A - 3
STAIR 1 713
CORRIDOR 104
OS
OS
N8CL
ARb
EL13
EL20
C6L
ARb
N8CL
ARb
EL14
BVL
ARb EM
C6L
P27L L1A - 45
ARb
OS
ARb
EM
E2
EL11
STOR 122C
TYP.
N8CL
E2
CORRIDOR A132
EL03
H1A - 5
EM
EL34
N8CL
K C6L
BVL
EM
ARb
N8CL
5
EL04
OFFICE ARb 115
BL
N8CL
5
H1A - 10
C6L
OS
N8CL
EL08
EL13
CLASSROOM 122
ARb
EL04
EL04
EL28
C6L
EL02
EL03
N8CL
EM
E
KILN 123B
ARaD
A1Fb
EL03
N8CL
P27L L1A - 45
K,3
BVL
EL02
EM
EM
EL03 EM
EL13
EL13
ELEV 721
OS EM
N8CL
N8CL
K
EL02
C6L
EM
C6L
5
ARb
FAM RR 116
OS
EL03
STOR 123A
A2 E604
ARaD
ARb
K
C
OS
ARb
CORRIDOR 117
RQ
ARb
K
OS
EM
K
a,b
A
PROJECT
E
ELEC 117A
E
C6L C6L
C6L
a,b
ARb
K
EL03
82984 G
KEYNOTES EL01
BL
b,c
b,c
C6L
H1A
E
RR
EL01
ARaD
COMPUTER LAB 121
E
H1A - 13
EL02
L2C
L1C
EL02
BL EM
ARaD a,c
EM
A1Fb
C6L
EM
N8CL
P27L L1A - 45
EL01
H1A - 11
A1Fb A1Fb
EL11
L2C
a,b
EL08
RC
A1Fb
OS
EM
N8CL N8CL STUDENT COMMONS 102
EL32
A1Fb
OS
EL11
RC
EL15
A1Fb
EL04
OS
EM OS
C6L
ARaD b,c ARaD a,c
A1Fb
N8CL
RS
a,b
E
b,c
EL04
A1Fb
EM
H1A - 3
BACK OF ROOM
T FRON OF OM EM RO
EL01
GIRLS 119
N8CL
ARaD a,c
E O F T EX
AT
JOHN F. HECK IV
b,c
EM
C6L
EM N6CL
b,c ARaD E
N6CL P27L L1A - 45
ARaD
c
RT
B2 E604
L2C
5
EL01 a,b
5
RC
5
EL08
K
a,b
ARCHITECT
EL08
EL14
a,b
RC
N6CL
a,b
a,b L3C
E
L2C
a,b
L3C
EL01
L2C
L2C
a,b
3
EL11
OF
E
a,b
ART 123
P9L c L1A - 19
L3C
ARb
a,b
A3 / EL101A
EL11
a,b
AKbE
a,b
E
AKa
L2C
R
D
L2C
P9L c L1A - 19
A1 E604
L3C
EL02
a,b
S
EL11
EL16
a,b
PR
AKaE
L2C
OS
P9L c L1A - 19
OS
L3C
EL02
L2C
P9L c L1A - 19
L3C
H1B - 11 EL16
L1A - 19 c P12L
H1B - 12
MEDIA CENTER 125
EM
AKa
L1A - 19 c P12L
a,b
BL
ARb
AKaE
WARMING KITCHEN 128
EL16
STOR 125A
BL
L1A - 19 c P12L
L3C
OS
STOR 128B
OS
AKaE
L1A - 19 c P12L
EL02
EL03
AKaE
FL H1B - 2
EL04
STOR 128A BL
BACK OF ROOM
b,c
R
ARaD
EL02
C6LS
EL08
b,c
BACK OF ROOM
A4 E604
b,c
EM
D
b,c
ARLD
EL03
E
RC
EM
ARLD
OS
EE
EM
EL02
AKb
ARb STOR 130B
a,c
ARLD
BL
OS
EL04
a,c
IN
E
EL01
OS
C6L
C6L
200 Longhorn Street Vega, TX 79092
CLASSROOM 129
AKb
E
FRONT OF ROOM
EL11
OS
EL11
EL13
EM a,c RC RC C6L
OS
a,c
EL01
VEGA ISD HIGH SCHOOL
ARaD a,c a,c FRONT OF ROOM
K
EL08
ST
ARaD
ARaD
AKb
EM
A. ALL EXIT SIGNS, TYPES "E", "E2" OR "EG", WILL BE CONNECTED TO CIRCUIT SERVING THE ROOM THEY ARE LOCATED IN AND FROM NO OTHER CIRCUIT. B. REFER TO SHEET E701 FOR ELECTRICAL LUMINAIRE SCHEDULE. C. REFER TO SHEET SERIES "EP" FOR ELECTRICAL ROOMS AND ELECTRICAL EQUIPMENT LAYOUT. D. REFER TO SHEET E604 FOR LIGHTING DIAGRAMS AND SEQUENCE OF OPERATION. E. REFER TO DETAILS C5 AND D3 ON SHEET E501 FOR LUMINAIRE MOUNTING. F. REFER TO ARCHITECTURAL SHEET SERIES "AE" FOR ADDITIONAL CEILING GRID MOUNTING SUPPORT INFORMATION. ALL LUMINAIRES WILL BE SECURELY SUPPORTED SEPARATELY FROM CEILING GRIDS TO CEILING STRUCTURE. G. REFER TO ARCHITECTURAL SHEETS FOR EXTERIOR LIGHTING ELEVATIONS. H. ALL EXTERIOR BUILDING LUMINAIRES WILL BE ROUTED THROUGH A TIME CLOCK AND CONTACTOR LOCATED IN THE ELECTRICAL ROOM WHERE THE PANEL FEEDING THOSE LUMINAIRES IS LOCATED. REFER TO DIAGRAM E3 ON SHEET E605 FOR ADDITIONAL INFORMATION. THE EXTERIOR BUILDING LUMINAIRES AND SITE LUMINAIRES MUST BE CONTROLLED SEPERATELY. I. CORRIDOR LUMINAIRES WILL BE ROUTED THROUGH A TIME CLOCK AND CONTACTOR LOCATED IN THE ELECTRICAL ROOM WHERE THE PANEL FEEDING THOSE LUMINAIRES IS LOCATED. REFER TO DIAGRAM C3 ON SHEET E605 FOR ADDITIONAL INFORMATION. J. ALL LUMINAIRES IN DASHED AREA WILL BE CONNECTED TO CIRCUIT INDICATEDUNLESS OTHERWISE NOTED.
EL16
C6L
KEYPLAN - N.T.S.
C6L
EL04 C6LWE H1B - 2
OS BL
EL16 C6LW H1B - 2
H1A - 7
DRAWN BY C6LWE H1B - 2
BL
EL16
STOR 164
20
A
REVIEWED BY
R9
C6LW H1B - 2
R7
C6LWE H1B - 2
R5
R8
9
10
11
13
14
15
16
AREA C
KIS JMM
EXISTING DATE
R8.1
02.15.2016
PROJECT NO:
14-0424.002
DRAWING NAME
MATCH LINE
LEVEL 1 LIGHTING PLAN - AREA B
R6 AREA B AREA A NORTH
A3
1
2
3
LEVEL 1 LIGHTING PLAN - AREA B SCALE: 1/8" = 1'-0"
0'
4
5
4'
8'
16'
NORTH
INE CH L MAT
2/15/2016 10:24:28 AM
R3
SHEET NO.
EL101B 6
1
2
3
4
5
6
GENERAL SHEET NOTES 5
1.9
2
3
4
5 5.1
5
EL16
FLE H1B - 2
E a,c
A4 E604
a,c
FRONT OF ROOM
a,c
FRONT OF ROOM
a,c
A4 E604
a,c
a,c
C6L ARaD
ARaD
ARaD
ARaD b,c
BACK OF ROOM ARaD
ARaD
5
EL08
K
E
BACK b,c OF ROOM ARaD
b,c
b,c
EL03
ARaD
BL
Z
EL01 EM
1.9
0.5
H1B - 18
2
3
b,c
ARaD
ARb
EL26
C6L
H1B - 6 CORRIDOR
C6L
OS
ARaD
BL
CLASSROOM
EL01
EL03
EL16 FLE H1B - 2
A150
EM
5 5.1
Z
A152
a,c
153
ARb
a,c
b,c
b,c
ARaD
C6L
ARaD
EL13 BACK OF ROOM
b,c OS
ARaD
4'
8'
16'
Y
b,c RC RC
OS
EL03
ARaD
BL
STOR 147A
CLASSROOM 147
BL
EL03
OS
X
RC RC
b,c A4 E604
H1B - 6
EL11 OS
b,c
BACK OF ROOM
b,c
ARaD
ARaD
ARaD
ARaD
ARaD
a,c
a,c
A1Fb
EL02
OS
A1Fb
A1Fb
EL04
EL16
BL
EL02
b,c
ARaD
ARaD
ARaD
ARaD
ARaD
ARaD
a,c
BACK OF ROOM
a,c
a,c
FRONT OF ROOM
T
STOR 137A
A1Fb
EL05
BL
b,c ARaD
EM
E
C6L
ARLD
ARLD
OS
a,c
ARb
C6L
b,c
b,c
EM
b,c
OS
ARb
b,c
b,c
ARaD
ARaD
ARaD
ARaD
ARaD
ARaD
ARaD
ARaD
FRONT OF ROOM
a,c
a,c
a,c
OS
P
H1B - 9
EL07
b,c
ARaD
ARaD
ARaD
a,c
a,c
BVL
TW
BVL
H1B - 8 a,c
a,c
a,c
ARaD
ARaD 5
b,c
b,c
ARaD
ARaD A4 E604
a,c
M
ARaD
ARaD
LAB 131
a,c
ARb
EL01
C6L
E
EL01
CORRIDOR 138 E
a,c
ARaD
OS ARaD
EM a,c
b,c
OS
BVL STOR/PREP 133 3 EM
N FRONT OF ROOM
EM
ALL KEYNOTE NUMBERS HAVE BEEN REVISED ON THIS SHEET
OS
b,c
BVL
MECH 154
EL03
a,c
RC RC
EL02
EL32
ONE PROGRAMMABLE TIME CLOCK WITH ROOF MOUNTED PHOTO CELL AND 4 POLE 20A CONTACTOR FOR EXTERIOR BUILDING LIGHTING. REFER TO DETAIL E3 ON SHEET E605 FOR ADDITIONAL INFORMATION. LUMINAIRE WILL BE CONNECTED TO LIGHTING BATTERY INVERTER "B1B" LOCATED IN ELEC 150. REFER TO DETAIL A1 ON SHEET E605 FOR TYPICAL EMERGENCY LIGHTING BATTERY INVERTER DIAGRAM. BATTERY INVERTER "B1B" WILL BE RATED FOR 1000 VA AND MAXIMUM DIMENSION SIZE OF 24"Hx26"Wx10"D. SHOULD BID LOT #4 BE ACCEPTED, THE LUMINAIRES AND DEVICES IN THIS DASHED AREA WILL BE RE-LOCATED AS INDICATED ON D1/EL101C. REFER TO DETAIL C6 ON SHEET SF503 FOR ALL CONDUITS ROUTED THROUGH WALL IN DASHED AREA. ONE PROGRAMMABLE TIME CLOCK WITH ROOF MOUNTED PHOTO CELL AND 4 POLE 20A CONTACTOR FOR CORRIDOR LIGHTING. REFER TO DETAIL C3 ON SHEET E605 FOR ADDITIONAL INFORMATION.
b,c ARaD
BACK b,c OF ROOM ARaD
ARb
C6L
EL01
EL04
EL27
DIGITAL "KEYPAD" LIGHTING CONTROL STATION CONSISTING OF ONE (OR MORE) 1-GANG PUSHBUTTON DEVICES WITH MULTIPLE ENGRAVED "SCENE RECALL" BUTTONS FOR CONTROL OF PRE-PROGRAMMED LIGHTING WITHIN ROOM. REFER TO CONTROL DIAGRAMS AND SEQUENCE OF OPERATION ON SHEET E604. ONE SWITCH; SWITCH TYPE AS INDICATED. WILL CONTROL THE LUMINAIRES IN ROOM. WALL-MOUNTED OCCUPANCY SENSOR, WATT STOPPER PW-100 OR APPROVED EQUAL. LOCATE PER MANUFACTURER'S RECOMMENDATIONS. SHOWN HERE FOR BID PURPOSES. REFER TO SHEET E604 FOR WIRING DIAGRAM AND ADDITIONAL INFORMATION ON SENSOR TYPE. CEILING-MOUNTED SENSOR, WATT STOPPER DT-355 OR APPROVED EQUAL. LOCATE PER MANUFACTURER'S RECOMMENDATIONS. SHOWN HERE FOR BID PURPOSES. COORDINATE WITH TELECOMMUNICATIONS RACK EQUIPMENT AND CABLE TRAY PLACEMENT FOR LUMINAIRE LOCATION. REFER SHEET SERIES "T" FOR TECHNOLOGY DETAILS. REFER TO SHEET SERIES "EP" FOR ELECTRICAL EQUIPMENT LAYOUT IN THIS ROOM. SWITCH WILL BE A 0-12 HOUR TWIST TIMER SWITCH. LOCATE ADJACENT TO LIGHTING CONTROL. SWITCH WILL BE MOTOR RATED FOR 1HP; INTERMATIC #FF12HH OR APPROVED EQUAL. LIGHTING ROOM CONTROLLER(S) FOR LIGHTING CONTROL SYSTEM IN THIS ROOM. REFER TO SHEET E604 FOR WIRING DIAGRAM AND ADDITIONAL INFORMATION ON ROOM CONTROLLER TYPE. CEILING-MOUNTED OCCUPANCY SENSOR, LOCATE PER MANUFACTURER'S RECOMMENDATIONS. SHOWN HERE FOR BID PURPOSES. REFER TO SHEET E604 FOR WIRING DIAGRAM AND ADDITIONAL INFORMATION ON SENSOR TYPE. ONE SWITCH; A KEYED MOMENTARY OVERRIDE SWITCH. THIS SWITCH WILL CONTROL CORRIDOR LIGHTING. IT WILL ALSO PROVIDE OVERRIDE OF LIGHTING BETWEEN 11 PM AND 5 AM. IF LIGHTING IS TURNED ON DURING THE NIGHT, THE LIGHTING WILL AUTOMATICALLY TURN OFF AFTER 30 MINUTES. LIGHTING WILL SIGNAL WITH A BLINK OF THE LIGHTS (5) FIVE MINUTES BEFORE SHUT DOWN. LABEL SWITCH "CORRIDOR CONTROL".
A4 E604
ARaD
ARaD
EM 3
EL26
EL11 E
John Heck 2016.02.15 13:47:56-07'00'
OS
ARaD EM
BL
ARaD
FRONT OF ROOM
H1B - 13
RC RC
a,c
CLASSROOM 136
ARaD
ARaD
EL08
FLE H1B - 2
STOR 136A
b,c
b,c
FRONT OF ROOM
b,c
ARaD
EL11 BACK OF ROOM
A4 E604
EL08
STOR 134A
EM
STOR 132A
EL08 CLASSROOM 132
C6L RC RC
E
ARaD
EL03
Addendum 004 REVISIONS 4
02/05/16
ADDENDUM #02
5
02/15/16
ADDENDUM #04
BL
EM
EL01 C6L
IS T E R G IO N A L E N
EL11
BACK OF ROOM ARb
EL16
EM
ARLD a,c
EL16
EL17
EL08
EL01
E
b,c
ARLD
EL15
VEST 142
EM
ARaD
a,c
A1Fb
C6L
ARb
RC RC
A4 E604
b,c
EL13 E
ARLD
EL11
A1Fb
K
CORRIDOR 138
ARb
b,c
ARLD
A1Fb
OS
IDF 141
b,c b,c
EL03
EM
EL01
BOYS 144
EL04 OS
A1Fb
E2
EL02
EL13 EM
BL
ARb
EM
BL
EL08
ARaD
B
EL02
EM
OS
H1B - 7 LAB 135
H1B - 9
JAN 139
EM
RC RC
FLE H1B - 2
EL07
EL11
C6L
STAFF RR 143
EL17
SPEC ED 137
EL16
EL06
EL08
FRONT OF ROOM
EL13
EM
EL03
BVL ELEC EM 150
FLE H1B - 2
Q
EL05
b,c
K
A1Fb
EL32
H1B H1B - 15
R
OS
b,c
K
C6L
EL03
H1B - 14 H1B - 16
EL06
S
OS
A4 E604
ARaD
K
EL15
U
EL03
EL03
K
EM
EM
EL04
H1B - 9
V
EL02
b,c
EL11
ARb
FRONT OF ROOM
BL
FL H1B - 2
C6L
GIRLS 145
W
RC RC
BACK OF ROOM
EL13
a,c
CLASSROOM 146
ARaD
EM
EL27
W.1
E
ARb
SS
PROJECT EL01
STOR 146A
EL08
EL01 C6L
82984 G
KEYNOTES
EL03
STOR 148A
H1B - 4
b,c
ARaD
ARaD
W.2
C6L
BL
EL08
EM
b,c
ARaD
b,c
C
ARb
E
OS
EL01
C6L
EM
EL01
E
ARaD
EM
EL08
A4 E604
b,c
E
C6L
EM
JOHN F. HECK IV
ARaD
RC RC
152
EL01
H1B - 5
b,c
CORRIDOR
E
EL08
STOR 149A FL H1B - 2
EM
b,c
OS
0'
ARb
A
b,c
OF
SCALE: 1/8" = 1'-0"
BACK b,c b,c OS OF ROOM ARaD ARaD CLASSROOM 148 ARaD
K
E O F T EX
AT
E
LEVEL 1 LIGHTING PLAN - BID LOT #4
EL11
E
CLASSROOM 149 ARaD
ARCHITECT
ARaD
R
A4 E604
ARaD
PR
ARaD
ARaD
S
EL11
D1
a,c
EM ARaD
ARaD
NORTH
a,c
R
a,c
D
a,c
E
Y.9
EE
A150A
FRONT OF ROOM
IN
A151A
VEST
FRONT OF ROOM
200 Longhorn Street Vega, TX 79092
STOR
VEGA ISD HIGH SCHOOL
STOR
ST
Y.9
D
4
RC RC ARaD
CLASSROOM A151
ARaD
b,c
RC RC
OS
b,c
5
EL08
b,c
1
OS
EL13
H1B - 18
ARaD
ARaD
EL11 b,c
OS
ARaD
A153
EL11
b,c
ARaD
VEST
A. ALL EXIT SIGNS, TYPES "E", "E2" OR "EG", WILL BE CONNECTED TO CIRCUIT SERVING THE ROOM THEY ARE LOCATED IN AND FROM NO OTHER CIRCUIT. B. REFER TO SHEET E701 FOR ELECTRICAL LUMINAIRE SCHEDULE. C. REFER TO SHEET SERIES "EP" FOR ELECTRICAL ROOMS AND ELECTRICAL EQUIPMENT LAYOUT. D. REFER TO SHEET E604 FOR LIGHTING DIAGRAMS AND SEQUENCE OF OPERATION. E. REFER TO DETAILS C5 AND D3 ON SHEET E501 FOR LUMINAIRE MOUNTING. F. REFER TO ARCHITECTURAL SHEET SERIES "AE" FOR ADDITIONAL CEILING GRID MOUNTING SUPPORT INFORMATION. ALL LUMINAIRES WILL BE SECURELY SUPPORTED SEPARATELY FROM CEILING GRIDS TO CEILING STRUCTURE. G. REFER TO ARCHITECTURAL SHEETS FOR EXTERIOR LIGHTING ELEVATIONS. H. ALL EXTERIOR BUILDING LUMINAIRES WILL BE ROUTED THROUGH A TIME CLOCK AND CONTACTOR LOCATED IN THE ELECTRICAL ROOM WHERE THE PANEL FEEDING THOSE LUMINAIRES IS LOCATED. REFER TO DIAGRAM E3 ON SHEET E605 FOR ADDITIONAL INFORMATION. THE EXTERIOR BUILDING LUMINAIRES AND SITE LUMINAIRES MUST BE CONTROLLED SEPERATELY. I. CORRIDOR LUMINAIRES WILL BE ROUTED THROUGH A TIME CLOCK AND CONTACTOR LOCATED IN THE ELECTRICAL ROOM WHERE THE PANEL FEEDING THOSE LUMINAIRES IS LOCATED. REFER TO DIAGRAM C3 ON SHEET E605 FOR ADDITIONAL INFORMATION. J. ALL LUMINAIRES IN DASHED AREA WILL BE CONNECTED TO CIRCUIT INDICATEDUNLESS OTHERWISE NOTED.
BL
OS
b,c
KEYPLAN - N.T.S.
FL H1B - 2
EL03
b,c ARaD
L
ARaD
BACK OF ROOM
b,c
b,c
ARaD
b,c
b,c OS
ARaD
ARaD
EL08
EL11 b,c
ARb RC RC
b,c
b,c
A4 E604
BACK OF ROOM
EM
b,c
A
ARb ARaD
J
ARaD
ARaD
ARaD
EL13
H1B - 7
K
FRONT OF ROOM
ARaD
EL11 b,c
H1B - 10
REVIEWED BY OS
b,c ARaD
ARaD
ARaD
ARaD
ARaD
a,c
A4 E604
KIS JMM
AREA C
b,c
ARaD
a,c
DRAWN BY
DATE
02.15.2016
PROJECT NO:
14-0424.002
DRAWING NAME
MATCH LINE
LEVEL 1 LIGHTING PLAN - AREA C
a,c
A3 / EL101B
AREA B AREA A
A3
1
2
3
LEVEL 1 LIGHTING PLAN - AREA C SCALE: 1/8" = 1'-0"
0'
4
5
4'
8'
16'
NORTH
INE CH L MAT
2/15/2016 10:56:56 AM
NORTH
SHEET NO.
EL101C 6
1
2
3
4
5
6
GENERAL SHEET NOTES 5
E
A. ALL EXIT SIGNS, TYPES "E", "E2" OR "EG", WILL BE CONNECTED TO CIRCUIT SERVING THE ROOM THEY ARE LOCATED IN AND FROM NO OTHER CIRCUIT. B. REFER TO SHEET E701 FOR ELECTRICAL LUMINAIRE SCHEDULE. C. REFER TO SHEET SERIES "EP" FOR ELECTRICAL ROOMS AND ELECTRICAL EQUIPMENT LAYOUT. D. REFER TO SHEET E604 FOR LIGHTING DIAGRAMS AND SEQUENCE OF OPERATION. E. REFER TO DETAILS C5 AND D3 ON SHEET E501 FOR LUMINAIRE MOUNTING. F. REFER TO ARCHITECTURAL SHEET SERIES "AE" FOR ADDITIONAL CEILING GRID MOUNTING SUPPORT INFORMATION. ALL LUMINAIRES WILL BE SECURELY SUPPORTED SEPARATELY FROM CEILING GRIDS TO CEILING STRUCTURE. G. REFER TO ARCHITECTURAL SHEETS FOR EXTERIOR LIGHTING ELEVATIONS. H. ALL EXTERIOR BUILDING LUMINAIRES WILL BE ROUTED THROUGH A TIME CLOCK AND CONTACTOR LOCATED IN THE ELECTRICAL ROOM WHERE THE PANEL FEEDING THOSE LUMINAIRES IS LOCATED. REFER TO DIAGRAM E3 ON SHEET E605 FOR ADDITIONAL INFORMATION. THE EXTERIOR BUILDING LUMINAIRES AND SITE LUMINAIRES MUST BE CONTROLLED SEPERATELY. I. CORRIDOR LUMINAIRES WILL BE ROUTED THROUGH A TIME CLOCK AND CONTACTOR LOCATED IN THE ELECTRICAL ROOM WHERE THE PANEL FEEDING THOSE LUMINAIRES IS LOCATED. REFER TO DIAGRAM C3 ON SHEET E605 FOR ADDITIONAL INFORMATION. J. ALL LUMINAIRES IN DASHED AREA WILL BE CONNECTED TO CIRCUIT INDICATEDUNLESS OTHERWISE NOTED.
ARCHITECT E O F T EX
A S
ST
AT
KEYNOTES PROJECT
EL02 3
RP
GYMNASIUM
BVL BVL
C
B100
STAIR 2
WEIGHT ROOM
169
A155
5
VEGA ISD HIGH SCHOOL
EL04
ONE SWITCH; SWITCH TYPE AS INDICATED. WILL CONTROL THE LUMINAIRES IN ROOM. CEILING-MOUNTED SENSOR, WATT STOPPER DT-355 OR APPROVED EQUAL. LOCATE PER MANUFACTURER'S RECOMMENDATIONS. SHOWN HERE FOR BID PURPOSES.
BVL FL H1B - 2
TRACK BVL
RN
156
EL04 OS
BVL
BVL
H1A - 23
RM
200 Longhorn Street Vega, TX 79092
EL02
200B
EL02
D
John Heck 2016.02.15 13:48:36-07'00'
BLEACHER
3
E
IS T E R G IO N A L E N
IN
OF
E
SS
EE
R
PR
E
D
82984 G
R
JOHN F. HECK IV
BVL
RK
BVL
5
BVL
FL H1B - 2 BVL
BLEACHERS 200A
B
RJ RG Addendum 004 REVISIONS 4
02/05/16
ADDENDUM #02
5
02/15/16
ADDENDUM #04
KEYPLAN - N.T.S.
DRAWN BY
R2
AREA C
EXISTING
REVIEWED BY DATE
LEVEL 1 ABOVE
JMM 02.15.2016
PROJECT NO:
14-0424.002
DRAWING NAME
MATCH LINE
A
KIS
LIGHTING PLAN BID LOT #3 AREA B AREA A
NORTH
LEVEL 1 LIGHTING PLAN - BID LOT #3 SCALE: 1/8" = 1'-0"
0'
4'
8'
16' NORTH
1
2
3
4
5
E NE H LLIIN CH ATTC M MA
2/15/2016 11:05:02 AM
A4
SHEET NO.
EL102A 6
1
2
3
4
5
6
GENERAL SHEET NOTES A. GFCI RECEPTACLES WILL BE INSTALLED AT ALL LOCATIONS AS REQUIRED BY THE LATEST VERSION OF NEC, STATE AND LOCAL CODES WHETHER INDICATED ON PLANS OR NOT. SOME LOCATIONS WILL BE WITHIN 6'-0" OF SINKS, EXTERIOR DOORS AND WET LOCATIONS. ALL EXTERIOR RECEPTACLE LOCATIONS WILL BE GFCI RATED AND WEATHERPROOF. B. MOUNT DEVICES IN CMU WALLS PER DETAIL B3 ON SHEET E501.
E
G 27
3
G 29
GIRLS B112
EP01 GIRLS VARSITY B111
ARCHITECT
ST
100B
S
SS
47
95
EP10
EP14 EP32
EP14 95
EP10 L0A - 97
51 EP33 47
93
EP34 EP54
STOR B103 EP61
RQ
GYMNASIUM B100
103
RP
R5
VEGA ISD HIGH SCHOOL
EP02
L0A - 31 L0A - 33
MOUNT DEVICE 6" ABOVE COUNTER TOP BACK SPLASH, TABLE TOP OR SINK. RECEPTACLE WILL BE GFCI RATED. MOUNTING HEIGHTS TO BE COORDINATED WITH ARCHITECT PRIOR TO COMMENCEMENT OF ANY WORK. MOUNT DEVICE 6" ABOVE COUNTER TOP BACK SPLASH OR TABLE TOP. MOUNTING HEIGHTS TO BE COORDINATED WITH ARCHITECT PRIOR TO COMMENCEMENT OF ANY WORK. DEVICE IS FOR SCOREKEEPER'S TABLE MOUTED AT 18" A.F.F. LOCATE ADJACENT TO LOW-VOLTAGE SIGNAL PULL BOX. REFER TO SHEET SERIES “T" FOR ADDITIONAL INFORMATION. LOCATE DEVICE OUTSIDE OF PADS PERIMETER. BASKETBALL RAISE/LOWER CONTROL DEVICE. PROVIDE CONDUCTORS BETWEEN CONTROL DEVICE AND MOTORS PER NOTE 31, AS WELL AS ARCHITECTURAL SPECIFICATIONS AND MANUFACTURER'S RECOMMENDATIONS. MAKE ALL NECESSARY TERMINATIONS FOR A COMPLETE AND OPERABLE SYSTEM. PROVIDE ONE SWITCH TO CONTROL EACH GOAL. JUNCTION BOX FOR SHOT CLOCK. LOCATE ADJACENT TO LOW-VOLTAGE SIGNAL PULL BOX FOR CONTROL. REFER TO ARCHITECTURAL INTERIOR ELEVATIONS FOR MOUNTING BEHIND SHOT CLOCK. AUDIO-VISUAL EQUIPMENT CABINET. INSTALL RECEPTACLE DEVICE IN BACK BOX RACK. REFER TO SHEET SERIES “T" FOR ADDITIONAL INFORMATION. SUMP PUMP CONTROL PANEL COMES COMPLETE WITH CONTROLS AND DISCONNECTING MEANS. COORDINATE EXACT LOCATION WITH INSTALLER PRIOR TO COMMENCEMENT OF WORK. PROVIDE 3/4" CONDUIT TO SUMP PUMP LOCATED IN PUMP ROOM B130. REFER TO SHEET E701 & SHEET SERIES "P" FOR ADDITIONAL INFORMATION. PROVIDE ADEQUATE SIZE OF OUTLET TO HOUSE FOUR BIG ASS FAN CONTROL DEVICES. DEVICE AND WIRING FOR BIG ASS FANS BY SPECIFICATION OF UNITS BY OTHERS. INSTALL AND TERMINATE PER SAME SPECIFICATIONS.
EP14
C
95
EP33 J
EP33 J
STAIR 2 169
49
L0A - 99
L0A - 101
RJ
EP14 93
RN
RG
HALL B100B
STOR B138
L0A - 69,71,73
103
63
RF SP-2
EP54
A
RM 95
RK
R
200 Longhorn Street Vega, TX 79092
PROJECT EP01
EP32
D
E
John Heck 2016.02.15 13:48:50-07'00'
EP33 EP34
EP61 CIRCUITS WITHIN DASHED AREA ARE FED FROM PANEL "L0A" UNLESS NOTED OTHERWISE
EE
IS T E R G IO N A L E N
IN
OF
E
E
EP A3 /
R
82984 G
KEYNOTES PA B102
A
JOHN F. HECK IV PR
D
E O F T EX
AT
PUMP ROOM B130
93
100B
EP14 93
EP A3 /
103
HALL B140
B
95 103
RJ RG
5
ALL KEYNOTE NUMBERS HAVE BEEN REVISED ON THIS SHEET
RF R2.9
Addendum 004 REVISIONS 4
02/05/16
ADDENDUM #02
5
02/15/16
ADDENDUM #04
KEY PLAN - N.T.S.
DRAWN BY AREA C
EXISTING
REVIEWED BY DATE
R2.1
LEVEL 1 ABOVE
R2
A
MATCH LINE
KIS JMM 02.15.2016
PROJECT NO:
14-0424.002
DRAWING NAME
R1.8
LOWER LEVEL POWER PLAN AREA A
AREA B AREA A
A3
1
2
3
LOWER LEVEL POWER PLAN - AREA A SCALE: 1/8" = 1'-0"
0'
4
5
4'
8'
16'
NORTH
INE CH L MAT
2/15/2016 11:07:33 AM
NORTH
SHEET NO.
EP100A 6
1
2
3
4
5
6
GENERAL SHEET NOTES A. GFCI RECEPTACLES WILL BE INSTALLED AT ALL LOCATIONS AS REQUIRED BY THE LATEST VERSION OF NEC, STATE AND LOCAL CODES WHETHER INDICATED ON PLANS OR NOT. SOME LOCATIONS WILL BE WITHIN 6'-0" OF SINKS, EXTERIOR DOORS AND WET LOCATIONS. ALL EXTERIOR RECEPTACLE LOCATIONS WILL BE GFCI RATED AND WEATHERPROOF. B. MOUNT DEVICES IN CMU WALLS PER DETAIL B3 ON SHEET E501.
E
ARCHITECT
R9 ST
25
G 27
1
EP53
EP01
G 29
GIRLS JV B113
L0A - 7
EP51
UNIFORM STOR B114
25
TYP.
9
21
L0A - 23
0A EP10 / 3 A
RQ
EP26
EP51
EP55
TYP.
J
19
B1 EP100B
91
EP26
L0A - 35
9 25
EP27 17
GIRLS COACH B108
G
EP01
9
9 G
EP29
17
ELEC B117
EP28
9
17
COACH RR B109
CORRIDOR B106
EP29
ELEV 714
EP27 EP28
RN
G 37 SP-1
EP35
47
T0A
49
BOYS COACH B119
47
EP08
L0A - 39
47 51
J
53
47 51 LDP0A
RQ
TO CU-05 ON ROOF
FC-05
57
51
53 FILM ROOM B118
EP55 L0A - 55
EP51
BOYS VARSITY B122
EP23 L0A - 39 TO CU-04 ON ROOF
51
EP15
B0A
91
A1 EP100B
TYP.
59 G
EP23 61
57
EP01
BOYS B123
EP01
IT B127
59 57 G
RJ RG
G
61 G
RF CORRIDOR B132
BOYS VISITOR B131
91
5
EP51
B1
ENLARGED ELEC B117 & B121
GIRLS VISITOR B133
R9
OFFICIALS RR B129
F
EP23
EP15
EP22 TO CU-06 ON ROOF L0A - 87
A
L0A - 89
EP01 63
TYP. G 65
EP51 TYP. OFFICIALS 65 B128
63
EP01 G
63
ALL KEYNOTE NUMBERS HAVE BEEN REVISED ON THIS SHEET
RE
G 63 G 65
67
65
L0A - 77 L0A - 83 L0A - 85
EP35
REVISIONS 4
02/05/16
ADDENDUM #02
5
02/15/16
ADDENDUM #04
67
67
KEY PLAN - N.T.S.
63
DRAWN BY
KIS
REVIEWED BY DATE
R2.9
RG
Addendum 004
65
A P100 E / A3
L0A - 75
67
EP51
65
EP01
FC-06
TYP.
67
SCALE: 1/4" = 1'-0" G
D
5
EP51
EP51
EP30
E
STAIR 1 713
57
FATC0
SUMP PUMP CONTROL PANEL COMES COMPLETE WITH CONTROLS AND DISCONNECTING MEANS. COORDINATE EXACT LOCATION WITH INSTALLER PRIOR TO COMMENCEMENT OF WORK. PROVIDE 3/4" CONDUIT TO SUMP PUMP LOCATED IN BOTTOM OF ELEVATOR PIT. REFER TO SHEET E701 & SHEET SERIES "P" FOR ADDITIONAL INFORMATION. FIRE ALARM CONTROL PANEL (FACP) OR FIRE ALARM TERMINAL CABINET (FATC). REFER TO SHEET E603 FOR ADDITIONAL INFORMATION. PROVIDE 120V POWER. TELECOMMUNICATIONS MAIN GROUNDING BUS BAR. REFER TO DETAIL A5 ON SHEET E501 AND ELECTRICAL GROUNDING DIAGRAM ON SHEET E603 FOR ADDITIONAL INFORMATION. USB CHARGER DUPLEX RECEPTACLE, HUBBELL # USB20X2. COLOR PER SPECIFICATION. DEVICE IS FOR FUTURE TRAINING EQUIPMENT. PROVIDE DEDICATED CIRCUIT. JUNCTION BOX FOR LOCKER ROOM CLOCK. LOCATE ADJACENT TO LOW-VOLTAGE SIGNAL PULL BOX FOR CONTROL. REFER TO ARCHITECTURAL INTERIOR ELEVATIONS FOR MOUNTING BEHIND LOCKER ROOM CLOCK. BATTERY INVERTER, PROVIDE 277V CIRCUIT. REFER TO SHEET EL100B AND DIAGRAM A1 ON SHEET E605 FOR ADDITIONAL INFORMATION.
39
59
TYP.
F
B
59
CLOTHES WASHER. MOUNT DEVICE AT 48” A.F.F. AND PROVIDE DEDICATED CIRCUIT. CLOTHES DRYER. MOUNT DEVICE AT 48” A.F.F. AND PROVIDE DEDICATED CIRCUIT. PROVIDE A GFCI RATED RECEPTACLE IN THE PIT OF THE ELEVATOR NEAR THE ENTRANCE TO THE PIT. MOUNT DEVICE 6" BELOW LOWER LEVEL OR AS DIRECTED BY ELEVATOR INSTALLER. PROVIDE A METAL END USE COVER PLATE. EXTEND CIRCUIT TO LUMINAIRE IN PIT. REFER TO SHEET SERIES "EL" FOR ADDITIONAL INFORMATION.
61
BOYS JV B124
61
EP63
MOUNT DEVICE 6" ABOVE COUNTER TOP BACK SPLASH, TABLE TOP OR SINK. RECEPTACLE WILL BE GFCI RATED. MOUNTING HEIGHTS TO BE COORDINATED WITH ARCHITECT PRIOR TO COMMENCEMENT OF ANY WORK. MOUNT DEVICE 6" ABOVE COUNTER TOP BACK SPLASH OR TABLE TOP. MOUNTING HEIGHTS TO BE COORDINATED WITH ARCHITECT PRIOR TO COMMENCEMENT OF ANY WORK. MAIN GROUNDING ELECTRODE GROUND BAR. REFER TO DETAIL A5 ON SHEET E501 AND ELECTRICAL GROUNDING DIAGRAM ON SHEET E603 FOR ADDITIONAL INFORMATION. DEVICE IS FOR MICROWAVE. COORDINATE ROUGH-IN HEIGHT WITH EQUIPMENT INSTALLER. REFER TO SHEET AE222 FOR ADDITIONAL INFORMATION. REFER TO SHEET E701 FOR ADDITIONAL ELECTRICAL CONNECTION REQUIREMENTS. REFER TO SHEET M701 FOR MECHANICAL / ELECTRICAL INFORMATION. EXTEND POWER CIRCUIT TO CONDENSING UNIT ON ROOF. REFER TO EP141C FOR ADDITIONAL INFORMATION. CONDENSATE LIFT PUMP. PLUMBING IN-LINE PUMP AND WATER HEATER. PROVIDE A THERMAL OVERLOAD TOGGLE SWITCH FOR IN-LINE PUMP, 1/2 HP MOTOR RATED. FOR WATER HEATER, PROVIDE A JUNCTION BOX AND THERMAL SWITCH SIMILAR TO PUMP. REFER TO SHEET SERIES "P" FOR MORE INFORMATION. REFER TO SHEET E701 FOR ELECTRICAL CIRCUITS AND ADDITIONAL ELECTRICAL CHARACTERISTICS FOR THIS UNIT.
53
M0A
EP22
FC-04
EP63
ELEC B117
L0A
F
RP
EP53 EP55
39
TYP.
57
EP22
RK
UNIFORM STOR B120
53
EP15
EP51
EP26
49
49
RM
L0A - 41
EP27
HDP0A
ELEC B121
EP30 L0A - 43,45
91
RR
EP23 EP25
RP
ELEC B121
G 17 JANITOR B115
21
19
21
C
L0A - 11 L0A - 13,15
19
FILM ROOM B107 19
R9
EP22 1
21
27
EP15
RR
EP25
25
TYP.
EP11
3
3
27
EP51
RS
EP08
29
GIRLS VARSITY B111
EP02
TRAINING B116
29
GIRLS B112
EP01
EP01
RT
29
G
PROJECT
L0A - 5 1
27
25
G
29
KEYNOTES EP53
200 Longhorn Street Vega, TX 79092
R3
John Heck 2016.02.15 13:49:06-07'00'
VEGA ISD HIGH SCHOOL
20
IS T E R G IO N A L E N
IN
OF
3
E
R5
SS
EE
R
E
R6
D
82984 G
R
JOHN F. HECK IV
XRB PR
R7
A S
R8
E O F T EX
AT
LEVEL 1 ABOVE
L0A - 79
JMM 02.15.2016
PROJECT NO:
14-0424.002
DRAWING NAME
LOWER LEVEL POWER PLAN AREA B
L0A - 81
AREA B
A1
1
ENLARGED IT B127
NORTH
A3
SCALE: 1/4" = 1'-0"
2
3
LOWER LEVEL POWER PLAN - AREA B SCALE: 1/8" = 1'-0"
0'
4
5
4'
8'
16'
NORTH
INE CH L MAT
2/15/2016 12:25:20 PM
AREA A
SHEET NO.
EP100B 6
1
2
3
4
5
6
GENERAL SHEET NOTES A. GFCI RECEPTACLES WILL BE INSTALLED AT ALL LOCATIONS AS REQUIRED BY THE LATEST VERSION OF NEC, STATE AND LOCAL CODES WHETHER INDICATED ON PLANS OR NOT. SOME LOCATIONS WILL BE WITHIN 6'-0" OF SINKS, EXTERIOR DOORS AND WET LOCATIONS. ALL EXTERIOR RECEPTACLE LOCATIONS WILL BE GFCI RATED AND WEATHERPROOF. B. MOUNT DEVICES IN CMU WALLS PER DETAIL B3 ON SHEET E501.
A3 / EP101B E
EP48
R2.9
J
J
TYP.
L1A - 47
VEST 124 WG L1A - 53
22
EP51 CIRCUITS WITHIN DASHED AREA ARE FED FROM PANEL "L1A" UNLESS NOTED OTHERWISE
2
TYP.
24
20
4
6 2
EP51
4
TYP.
6
2
ARCHITECT
4
F
OF
XRB
G
SS
IS T E R G IO N A L E N
John Heck 2016.02.15 13:50:57-07'00'
KEYNOTES RU
PROJECT T
F
EP31
J
EP48
L1A - 26
RT
22
M0A - 1,3,5 EP51
RS
EP58
EP31
T
EP59 EP60
22
J L1A - 28 WG L1A - 53
BASKETBALL GOAL HOIST MOTOR. PROVIDE A 3/4" CONDUIT DOWN TO OUTLET FOR CONTROL LOCATED PER NOTE 32. PUSH BUTTON ACTUATOR FOR MOTORIZED DOOR OPERATOR(S). COORDINATE ROUGH-IN AND WIRING REQUIREMENTS WITH DOOR INSTALLER. WIRE ALL DEVICES COMPLETE FOR OPERATION. REFER TO DETAIL C3 ON SHEET E501. USB CHARGER DUPLEX RECEPTACLE, HUBBELL # USB20X2. COLOR PER SPECIFICATION. JUNCTION BOX FOR CEILING MOUNTED SCORE BOARD. COORDINATE BEST LOCATION WITH SCOREBOARD INSTALLER. BID LOT #3 . REFER TO SHEET EP102A FOR ADDITIONAL INFORMATION. MOUNT DISCONNECT OUTSIDE OF THE DIAMETER OF THE FAN IN AN ACCESSIBLE LOCATION FOR MAINTENANCE. PROVIDE A 3/4" CONDUIT TO CONTROL LOCATION. REFER TO KEYNOTE EP61 ON THIS SHEET AND SHEET EP100A FOR LOCATION OF CONTROL. COORDINATE WITH MANUFACTURER'S INSTRUCTIONS PRIOR TO COMMENCEMENT OF WORK.
VEGA ISD HIGH SCHOOL
EP60
EP31
RR 14
RQ EP59
EP31
T
J
16
RP
L1A - 36 20
18
EP58 24
J
14
C
L1A - 38
STAIR 2 169 16 T
J
RN
EP51 TYP.
EP31
L1A - 30 18
A 24
14
RM
J
RK
T
16 L1A - 34
EP31
200 Longhorn Street Vega, TX 79092
D
E
E
M0A - 7,9,11
82984
R
24
PR
RV
R
JOHN F. HECK IV
6
D
EP60
E
2
4
A S
TYP.
E O F T EX
AT
ST
6
EE
EP51
IN
20
18
J
EP60
T 14
L1A - 32
F
EP31
22 M0A - 8,10,12
16
RJ RG
B
8
EP60
F
10
12 8
M0A - 2,4,6
RF
EP51 TYP.
10
ALL CIRCUITING HAS BEEN REVISED ON THIS SHEET
20
12
8 20 10
WG L1A - 53
EP51 TYP.
RE
REVISIONS
12
12
24
8
10
RD
Addendum 004 4
02/05/16
ADDENDUM #02
EP51 TYP.
22
KEY PLAN - N.T.S.
RB DRAWN BY
RA
KIS
REVIEWED BY AREA C
DATE
02.15.2016
PROJECT NO:
A
JMM
EXISTING
14-0424.002
DRAWING NAME
MATCH LINE
LEVEL 1 POWER PLAN - AREA A AREA B AREA A
A3
1
2
3
LEVEL 1 POWER PLAN - AREA A SCALE: 1/8" = 1'-0"
0'
4
5
4'
8'
16'
NORTH
INE CH L MAT
2/15/2016 12:31:43 PM
NORTH
SHEET NO.
EP101A 6
1
2
3
4
5
6
GENERAL SHEET NOTES R9 RR
A. GFCI RECEPTACLES WILL BE INSTALLED AT ALL LOCATIONS AS REQUIRED BY THE LATEST VERSION OF NEC, STATE AND LOCAL CODES WHETHER INDICATED ON PLANS OR NOT. SOME LOCATIONS WILL BE WITHIN 6'-0" OF SINKS, EXTERIOR DOORS AND WET LOCATIONS. ALL EXTERIOR RECEPTACLE LOCATIONS WILL BE GFCI RATED AND WEATHERPROOF. B. MOUNT DEVICES IN CMU WALLS PER DETAIL B3 ON SHEET E501.
EP62
M1A
EP64
RQ
ELEC 117A
A3 / EP101C
A3 / EP101C J
12
12
7
EP04
3
25
23
G
EP01
EP51
G
EP01
H
EP51 EP02
EP51
EP01
TYP.
TYP.
9
9
5
G
23
G.9
25
EP51 5
RT
3
WARMING KITCHEN 128
9
EP09
EP02 EP51
L1A - 15
TYP.
RS
23
25
JOHN F. HECK IV
5
EP51
A3 / EP101A
52
9 7
TYP.
3
5
T
T
54
56
L0A - 64
T
EP01
EP51
G 48
TO CU-07 STOR ON ROOF L1A - 31 123A 23 KILN L1A - 27,29 123B
COMPUTER LAB 121
EP04
50
EP37
EP03
EP04
52
E
52
EP07 58
CORRIDOR A132
54 48
EP51
G
56
ELEC 117A
BOYS 118
39
F
EP36
GIRLS 119
EP01
EP51
EP02
RP
T T
41
F
EP21
EP01
EP23
25
T
43
RQ
EP15
54
EP51
56 52
CORRIDOR 117
G
RN
EP09
D.2
EP11
RM
EP12 EP13
G
39
L0A - 60
JANITOR 120
A5 EP101B
L0A - 62
48 G
CLASSROOM 122
HDP0A
EP51 C
EP56 41
EP15
D
42
58
EP21
RK
42
EP57
EP22
EP02
EP23 EP29
44
STUDENT COMMONS 102
EP51
FAM RR 116 43
ELEV 721
48
EP04
58
42
58
46
G
EP01
46 40
EP51
OFFICE 115
44 38
41
40
EP51
CORRIDOR 104
34 39
EP02
32
G
CONF 103A
EP02 EP09
EP04
34
EP51 EP51
STAGE A124
32
B
EP50 36
26
EP03
CORRIDOR 110
16
58
ISS 107
22
22
20
C EP03
L0A - 10
TYP. J
26
26
EP03
PRINC 105
16
18
PROP STOR A125
G
EP01
B
L0A - 14 4
6
DEVICE IS FOR WALL MOUNTED SHORT-THROW PROJECTOR MOUNTED IN MULTI-SERVICE BOX. REFER TO MOUNTING DETAILS ON SHEET SERIES “T” FOR ADDITIONAL INSTALLATION INFORMATION. WASHER & DRYER ARE STACKED ONE ON TOP OF THE OTHER. RECEPTACLES WILL BE MOUNTED AT 18" A.F.F. AND 36" A.F.F., PROVIDE DEDICATED CIRCUITS. FLOORBOX. PROVIDE A 3/4" CONDUIT BETWEEN EACH DEVICE AND FOR HOMERUN. REFER TO SHEET SERIES "ET" FOR FLOORBOX DETAILS AND ADDITIONAL INFORMATION. CIRCUIT INDICATED WILL SERVE ALL DEVICES IN FLOORBOX. REFER TO SHEET SERIES "EL" FOR ADDITIONAL INFORMATION. DEVICE IS FOR MICROWAVE. COORDINATE ROUGH-IN HEIGHT WITH EQUIPMENT INSTALLER. REFER TO SHEET AE222 FOR ADDITIONAL INFORMATION. MOUNT DEVICE AT 48” A.F.F FOR REFRIGERATOR, PROVIDE DEDICATED CIRCUIT. DEVICE IS FOR COPIER, PROVIDE DEDICATED CIRCUIT. CONTRACTOR WILL MATCH NEMA CONFIGURATION OF RECEPTACLE WITH UNIT PLUG. COORDINATE PRIOR TO ORDERING RECEPTACLE DEVICE. REFER TO SHEET E701 FOR ADDITIONAL ELECTRICAL CONNECTION REQUIREMENTS. REFER TO SHEET M701 FOR MECHANICAL / ELECTRICAL INFORMATION. MOUNT DEVICE AT 30” FOR RANGE, PROVIDE DEDICATED CIRCUIT. CONTRACTOR WILL MATCH NEMA CONFIGURATION OF RECEPTACLE WITH UNIT PLUG. COORDINATE PRIOR TO ORDERING RECEPTACLE DEVICE. EXTEND POWER CIRCUIT TO CONDENSING UNIT ON ROOF. REFER TO EP141C FOR ADDITIONAL INFORMATION. CONDENSATE LIFT PUMP. SUMP PUMP CONTROL PANEL COMES COMPLETE WITH CONTROLS AND DISCONNECTING MEANS. COORDINATE EXACT LOCATION WITH INSTALLER PRIOR TO COMMENCEMENT OF WORK. PROVIDE 3/4" CONDUIT TO SUMP PUMP LOCATED IN BOTTOM OF ELEVATOR PIT. REFER TO SHEET E701 & SHEET SERIES "P" FOR ADDITIONAL INFORMATION. ELECTRIC KILN. CONTRACTOR WILL MATCH NEMA CONFIGURATION OF RECEPTACLE WITH UNIT PLUG. COORDINATE PRIOR TO ORDERING RECEPTACLE DEVICE. DOWNDRAFT VENTILATION SYSTEM (EXHAUST BLOWER) FOR ELECTRIC KILN. CONTRACTOR WILL MATCH NEMA CONFIGURATION OF RECEPTACLE WITH UNIT PLUG. COORDINATE PRIOR TO ORDERING RECEPTACLE DEVICE. DEVICE IS FOR EXHAUST HOOD ABOVE RANGE. COORDINATE ROUGH-IN HEIGHT WITH EQUIPMENT INSTALLER. CONTROL SWITCH FOR EXHAUST HOOD ABOVE RANGE. COORDINATE ROUGH-IN HEIGHT WITH EQUIPMENT INSTALLER. PUSH BUTTON ACTUATOR FOR MOTORIZED DOOR OPERATOR(S). COORDINATE ROUGH-IN AND WIRING REQUIREMENTS WITH DOOR INSTALLER. WIRE ALL DEVICES COMPLETE FOR OPERATION. REFER TO DETAIL C3 ON SHEET E501. MOTORIZED COILING GATE/DOOR. PROVIDE POWER INDICATED AND A 3/4" CONDUIT TO SWITCH FOR CONTROL OF DOOR. USB CHARGER DUPLEX RECEPTACLE, HUBBELL # USB20X2. COLOR PER SPECIFICATION. REFER TO SHEET E601 FOR ELEVATOR ELECTRICAL EQUIPMENT, TERMINATION INFORMATION AND POWER REQUIREMENTS. COORDINATE ALL REQUIREMENTS WITH ELEVATOR MANUFACTURER FOR A COMPLETE AND OPERATIONAL SYSTEM. 120V POWER FOR ELEVATOR CAB LIGHTS AND ALARMS. COORDINATE ALL REQUIREMENTS WITH ELEVATOR MANUFACTURER FOR A COMPLETE AND OPERATIONAL SYSTEM. TIME CLOCK, PROVIDE A 277V CIRCUIT. REFER TO SHEET EL101B AND DIAGRAM C3 ON SHEET E605 FOR ADDITIONAL INFORMATION. TIME CLOCK, PROVIDE A 277V CIRCUIT. REFER TO SHEET EL101B AND DIAGRAM E3 ON SHEET E605 FOR ADDITIONAL INFORMATION.
ALL KEYNOTE NUMBERS HAVE BEEN REVISED ON THIS SHEET
4
EP11
LOUNGE 109A
MOUNT DEVICE 6" ABOVE COUNTER TOP BACK SPLASH, TABLE TOP OR SINK. RECEPTACLE WILL BE GFCI RATED. MOUNTING HEIGHTS TO BE COORDINATED WITH ARCHITECT PRIOR TO COMMENCEMENT OF ANY WORK. MOUNT DEVICE 6" ABOVE COUNTER TOP BACK SPLASH OR TABLE TOP. MOUNTING HEIGHTS TO BE COORDINATED WITH ARCHITECT PRIOR TO COMMENCEMENT OF ANY WORK. REFER TO CASEWORK DETAILS INDICATED ON "A" SHEET SERIES FOR MOUNTING OF DEVICE IN OR ON CASEWORK. CONDUIT WILL STUB THROUGH WALL OR FLOOR AND INTO DEVICE. MOUNTING HEIGHTS TO BE COORDINATED WITH ARCHITECT PRIOR TO COMMENCEMENT OF ANY WORK IF HEIGHTS ARE NOT INDICATED IN CASE WORK DETAILS.
5
8
VEST 100
L0A - 2
A
Addendum 004 REVISIONS 4
02/05/16
ADDENDUM #02
5
02/15/16
ADDENDUM #04
WG L1A - 53
16
L1A - 51
John Heck 2016.02.15 13:52:32-07'00'
RD
J
24
EP48
EP01
EP02
18
VEST 101
43
18
4
G 6
8
16
EP64
8
L0A - 12
22
EP03
EP62
RE
8
EP02
EP12
L1A - 49
EP57
6
6
EP13
24
EP48
EP56
4
20
24
EP51
RF
STOR 111
8
RECEPTION 103
EP48
RG
20 41
EP40
44
WORKROOM 109
39
EP39
58
CORRIDOR 106
32
30
RJ
46
STOR 122C
G
M 112
EP01
30
43
EP37
EP01 W 108
FILES 113
CIRCUITS WITHIN DASHED AREA ARE FED FROM PANEL "L0A" UNLESS NOTED OTHERWISE
46 36
36 36
46
G
44 36 G
34
EP51
EP01 EP01
32
EP36
44
M 122B
W 122A
40
TEST STOR 115A
EP51
43
38
IS T E R G IO N A L E N
PROJECT
FC-07
23
54
EP51
SS
KEYNOTES
EP03
50
3
E
25
5
EP51
82984 G
21 23
EP51
41
OF
EP51
L1A - 13
EP09
RR
E
9
L1A - 35
A
7
L1A - 11
EP09
D
E O F T EX
AT
R
CONCESSION 127
EP04
21
TYP.
G
PR
EP11
EP02 EP51
EP01
ARCHITECT
S
MEDIA CENTER 125
EP13 L1A - 17
ART 123
R
L1B - 30 L1B - 26,28 L1B - 24
7
D
9
SCALE: 1/4" = 1'-0"
E
EP01
2448
2448
1
3
STOR 125A
10
ENLARGED ELEC 117A
EE
G
2472
2472
2472
STOR 128B
5
A5
CIRCUITS WITHIN DASHED AREA ARE FED FROM PANEL "L1A" UNLESS NOTED OTHERWISE
12 G
J
L1B - 18,20
EP01
3
EP01 G
L1B - 22
G 7
EP15 A3 E401
EP12
IN
EF-02
EP40
200 Longhorn Street Vega, TX 79092
T
STOR 129A
EP01
EP11
L1B - 16 10 G
T F
39
EP23
EP21 EP07
L1B - 14
FC-03
EP15
EP39
EP01 T
L0A - 48 F
8 CIRCUITS WITHIN DASHED AREA ARE FED FROM PANEL "L1B" UNLESS NOTED OTHERWISE
RR 130A
L1A - 37
RP
EP22
EP04 STOR 130B
H1A
VEGA ISD HIGH SCHOOL
CLASSROOM 129
8
10
L1A - 33
? ?
TO CU-03 ON ROOF
ST
LIFESKILLS 130
EP50
L1A
J
E
TYP.
EP48
KEY PLAN - N.T.S.
TYP. J
R9
STOR 164 CIRCUITS WITHIN DASHED AREA ARE FED FROM PANEL "L1A" UNLESS NOTED OTHERWISE
R7
WG L1A - 53
39
R8
R8.1 DRAWN BY
KIS
REVIEWED BY
13
14
15
16
AREA C
DATE
02.15.2016
PROJECT NO:
A
14-0424.002
DRAWING NAME
MATCH LINE
R5
JMM
EXISTING
LEVEL 1 POWER PLAN - AREA B
R6
2/15/2016 12:36:31 PM
1
2
AREA A NORTH
A3 R3
3
LEVEL 1 POWER PLAN - AREA B SCALE: 1/8" = 1'-0"
0'
4
5
4'
8'
16'
NORTH
INE CH L MAT
1A EP10 A3 /
AREA B
SHEET NO.
EP101B 6
1
2
3
4
5
6
GENERAL SHEET NOTES 1.9 2
3
4
A. GFCI RECEPTACLES WILL BE INSTALLED AT ALL LOCATIONS AS REQUIRED BY THE LATEST VERSION OF NEC, STATE AND LOCAL CODES WHETHER INDICATED ON PLANS OR NOT. SOME LOCATIONS WILL BE WITHIN 6'-0" OF SINKS, EXTERIOR DOORS AND WET LOCATIONS. ALL EXTERIOR RECEPTACLE LOCATIONS WILL BE GFCI RATED AND WEATHERPROOF. B. MOUNT DEVICES IN CMU WALLS PER DETAIL B3 ON SHEET E501.
5.1
5
EP48 L1B - 87 WG
TYP.
84
80
82
E
86
J
80
EP04
90
86
VEST
88 90
EP04
A153
84 82
88 J
1
88
CLASSROOM 82
CLASSROOM
L1B - 66
A151
84
0.5
A150
90
1.9
2
3
4
5
5.1
56
EP49 86
A151A
Z
EP02
EP02
CORRIDOR
EP02
EP02
EP02
EP02
90 STOR
EP48
A150A
TYP.
A152 82
84
88
82
90
88
L1B - 87 WG
Z 5
Y.9
Y.9
1
3
EP04
5
32
J
1
36
32
3
34 5
EP04
34
36
J
ARCHITECT E O F T EX
AT
A S
ALL KEYNOTE NUMBERS HAVE BEEN REVISED ON THIS SHEET
ST
80 84 STOR
4'
8'
16'
Y
CLASSROOM 149
1
CLASSROOM 148
32
5
EP02
EP02
EP02
3
EP02
5
9
STOR 147A
3
11
EP02
EP02
EP02
34
9
36
40
EP02
EP02 34
42
EP02
40
EP02
EP02
11
EP01
EP02
STOR 146A
EP03
38
CLASSROOM 147
X
2
CLASSROOM 146
56
EP04 9
11
40
42
EP06
L1B
V
L1B - 13
11
EP16 M1B
TO CU-01 ON ROOF
EP15
C
EP22
B1B
11
7
7
38
GIRLS 145
T1B
V
L1B - 58 G
13 G
L1B - 87 WG
EP23
ELEC 150
C1 EP101C
ENLARGED ELEC 150
EP01
13 G
L1B - 60
48
EP02
EP02
EP04 33
FC-02
L1B - 15 TO CU-02 ON ROOF
B L1B - 17 L1B - 19
S
EP15
41 G
39
45 G
43 G
EP02 41 G
LAB 135
J
G 39
37
TYP.
TYP.
F
EP35 EP23
R
U
41 G
G
37
41 G
EP09
J
T
L1B - 51
T
43 G
5
Q P 1.9
A1 EP101C
MECH 154
L1B - 87 WG
STOR/PREP 133
N
2
65
EP51 54
63 UH-01
MECH 154
L1B - 65
EP25
Q
L
EP25
L1B - 83 L1B - 85
EP02
J
4
65 L1B - 73
G 67
EP19
J G 69
G
71
EP02 DHW-2
DHW-1 G
J
J
G
63
J
G 67
EP02
54
02/15/16
ADDENDUM #04
EP02
STOR 132A
EP02 6
56 T T
CLASSROOM 132
DRAWN BY
6
4
KIS
REVIEWED BY
JMM
AREA C DATE
02.15.2016
PROJECT NO:
G 69
EP01
4
G G
D
5
KEY PLAN - N.T.S.
4
65
63
EP04 2
2
6
14-0424.002
DRAWING NAME
MATCH LINE
6
LEVEL 1 POWER PLAN - AREA C
4
A3 / EP101B
A3 / EP101B
N
ADDENDUM #02
52
G 71
63
02/05/16
STOR 134A
L1B - 77
LAB 131 65
EP02
EP03
69
4
2
69
G G 71
G 67
EP02
6
EP02
EP20 L1B - 75 G 71
67 G
J
TYP.
P
ILP-1 F
ILP-1 F
G 71
EP06 EP51 EP50 TYP.
L1B - 81
EP24 A
EP15
G 69
REVISIONS
54
G
J
EP09
Addendum 004
50
L1B - 57
63 L1B - 79
EP52
L1B - 62
EP04
J
CLASSROOM 134
TELECOMMUNICATIONS MAIN GROUNDING BUS BAR. REFER TO DETAIL A5 ON SHEET E501 AND ELECTRICAL GROUNDING DIAGRAM ON SHEET E603 FOR ADDITIONAL INFORMATION. DISHWASHER. INSTALL OUTLET WITHIN BASE CABINETRY AT ACCESSIBLE LOCATION. COORDINATE WITH EQUIPMENT INSTALLER. REFER TO DETAIL C6 ON SHEET SF503 FOR ALL CONDUITS ROUTED THROUGH WALL IN DASHED AREA. PUSH BUTTON ACTUATOR FOR MOTORIZED DOOR OPERATOR(S). COORDINATE ROUGH-IN AND WIRING REQUIREMENTS WITH DOOR INSTALLER. WIRE ALL DEVICES COMPLETE FOR OPERATION. REFER TO DETAIL C3 ON SHEET E501. SHOULD BID LOT #4 BE ACCEPTED, THE DEVICES IN THIS DASHED AREA WILL BE RE-LOCATED AS INDICATED ON D1/EP101C. MOTORIZED COILING GATE/DOOR. PROVIDE POWER INDICATED AND A 3/4" CONDUIT TO SWITCH FOR CONTROL OF DOOR. USB CHARGER DUPLEX RECEPTACLE, HUBBELL # USB20X2. COLOR PER SPECIFICATION. DEVICE IS FOR PRINTER. PROVIDE DEDICATED CIRCUIT.
EP03 EP52
63
61 G 67
52
52
EP04
M
EP49
65 G 61
EP48
54
EP50
L1B - 55
EP38
61
EP04
52
EP44
56
J
37
EP12 EP01
37
52
L1B - 53
G 39
EP19
54
50
EP20
35
J
SCALE: 1/4" = 1'-0"
1
L1B - 59
T
B1
35
45
G
EP04
T
39
46 48
50
EP03
J
EP04
EP35
44 44
35
ENLARGED IDF 141
L1B - 64
EP38
J
45 G
43 G
48
EP04
45
EP06 EP51
EP22
46
L1B - 49
G
J
43
G
EP01
43 G
45
41 G G
EXTEND POWER CIRCUIT TO CONDENSING UNIT ON ROOF. REFER TO EP141C FOR ADDITIONAL INFORMATION. CONDENSATE LIFT PUMP. EMERGENCY POWER OFF (EPO) RED MUSHROOM HEAD PUSH BUTTON FOR WATER HEATER EMERGENCY SHUT OFF. TERMINATE CONDUCTORS TO EACH WATER HEATER PER MANUFACTURER'S DIRECTION. PLUMBING IN-LINE PUMP AND WATER HEATER. PROVIDE A THERMAL OVERLOAD TOGGLE SWITCH FOR IN-LINE PUMP, 1/2 HP MOTOR RATED. FOR WATER HEATER, PROVIDE A JUNCTION BOX AND THERMAL SWITCH SIMILAR TO PUMP. REFER TO SHEET SERIES "P" FOR MORE INFORMATION. REFER TO SHEET E701 FOR ELECTRICAL CIRCUITS AND ADDITIONAL ELECTRICAL CHARACTERISTICS FOR THIS UNIT.
EP23 EP24
46
MAIN GROUNDING ELECTRODE GROUND BAR. REFER TO DETAIL A5 ON SHEET E501 AND ELECTRICAL GROUNDING DIAGRAM ON SHEET E603 FOR ADDITIONAL INFORMATION. FLOORBOX. PROVIDE A 3/4" CONDUIT BETWEEN EACH DEVICE AND FOR HOMERUN. REFER TO SHEET SERIES "ET" FOR FLOORBOX DETAILS AND ADDITIONAL INFORMATION. CIRCUIT INDICATED WILL SERVE ALL DEVICES IN FLOORBOX. REFER TO SHEET SERIES "EL" FOR ADDITIONAL INFORMATION. MOUNT DEVICE AT 48” A.F.F FOR REFRIGERATOR, PROVIDE DEDICATED CIRCUIT. REFER TO SHEET E701 FOR ADDITIONAL ELECTRICAL CONNECTION REQUIREMENTS. REFER TO SHEET M701 FOR MECHANICAL / ELECTRICAL INFORMATION. TIME CLOCK, PROVIDE A 277V CIRCUIT. REFER TO SHEET EL101C AND DIAGRAM E3 ON SHEET E605 FOR ADDITIONAL INFORMATION. BATTERY INVERTER, PROVIDE 277V CIRCUIT. REFER TO SHEET EL101C AND DIAGRAM A1 ON SHEET E605 FOR ADDITIONAL INFORMATION. TIME CLOCK, PROVIDE A 277V CIRCUIT. REFER TO SHEET EL101C AND DIAGRAM C3 ON SHEET E605 FOR ADDITIONAL INFORMATION. JUNCTION BOX FOR FUME HOOD. CONTRACTOR TO PROVIDE POWER TO FUME HOOD WHICH INCLUDES LIGHTING AND RECEPTACLES. IN ADDITION, PROVIDE POWER TO HOOD CONTROLLER PROVIDED BY MECHANICAL. COORDINATE WITH MANUFACTURER'S REQUIREMENTS AND SHEET SERIES "M" PRIOR TO COMMENCEMENT OF WORK.
EP22
EP25
37
EP19
L1B - 47
48
29
29
37
EP02 IDF 141
33
31 39
CORRIDOR 138
DEVICE IS FOR WALL MOUNTED SHORT-THROW PROJECTOR MOUNTED IN MULTI-SERVICE BOX. REFER TO MOUNTING DETAILS ON SHEET SERIES “T” FOR ADDITIONAL INSTALLATION INFORMATION. CONTRCATOR WILL PROVIDE GFCI RATED DEVICE AND COVER PLATE IN CASEWORK. CASEWORK WILL BE PROVIDED WITH OPENINGS PRE-MILLED. CONTRACTOR WILL INSTALL RACEWAY BACK TO FLOOR JUNCITON BOX THROUGH CASEWORK IN A WAY SO AS NOT TO HAMPER THE USE OF THE CASEWORK DRAWERS/CABINET FUNCTIONALITY. CONTRACTOR WILL COORDINATE WITH OHTER ULITIES PRIOR TO COMMENCEMENT OF ANY WORK FOR BEST ROUTING PATHS OF ALL UTILITIES IN CASEWORK. CONTRACTOR WILL REFER TO SHEET SERIES "AE" FOR CASEWORK DETAILS AND ADDITIONAL INFORMATION.
JUNCTION BOX FOR ISIMET CONTROL PANEL. CONTRACTOR WILL COORDINATE QUANTITY OF CIRCUITS TO BE ROUTED THROUGH UNIT SUPPLIED BY CONTRACTOR. ALL POWER CIRCUITS WITHIN ROOM WILL BE SHUT OFF IN THE EVENT OF AN EMERGENCY. REFER TO SHEET SERIES "P" FOR ADDITIONAL INFORMATION.
48
CLASSROOM 136
MOUNT DEVICE 6" ABOVE COUNTER TOP BACK SPLASH, TABLE TOP OR SINK. RECEPTACLE WILL BE GFCI RATED. MOUNTING HEIGHTS TO BE COORDINATED WITH ARCHITECT PRIOR TO COMMENCEMENT OF ANY WORK. MOUNT DEVICE 6" ABOVE COUNTER TOP BACK SPLASH OR TABLE TOP. MOUNTING HEIGHTS TO BE COORDINATED WITH ARCHITECT PRIOR TO COMMENCEMENT OF ANY WORK. REFER TO CASEWORK DETAILS INDICATED ON "A" SHEET SERIES FOR MOUNTING OF DEVICE IN OR ON CASEWORK. CONDUIT WILL STUB THROUGH WALL OR FLOOR AND INTO DEVICE. MOUNTING HEIGHTS TO BE COORDINATED WITH ARCHITECT PRIOR TO COMMENCEMENT OF ANY WORK IF HEIGHTS ARE NOT INDICATED IN CASE WORK DETAILS.
EP20
44
EP02
3
WG L1B - 87
STOR 136A
EP02
SPEC ED 137
31
J
46
31
CIRCUITS WITHIN DASHED AREA ARE FED FROM PANEL "L1B" UNLESS NOTED OTHERWISE
EP19
VEST 142 46
29
EP18
TYP.
J
L1B - 68
U
T
J
B1 EP101C
33
EP17
EP48
IDF 141
33
SCALE: 1/4" = 1'-0"
EP16
56
STOR 137A
EP12 EP15
EP01
G 13 JAN 139
G
STAFF RR 143
13 G
U
F
L1B - 27 L1B - 23 L1B - 25 L1B - 21
38
BOYS 144
56
EP01
EP08
42
EP08 40 EP09
W
HDP1B
C1
EP04
W.1
EP17
FC-01
9
EP44
ELEC 150
42
40
EP04
W.2
H1B
EP18
9
E
PROJECT
STOR 148A
42 7
1.9
KEYNOTES
36
STOR 149A
John Heck 2016.02.15 13:53:41-07'00'
200 Longhorn Street Vega, TX 79092
0'
IS T E R G IO N A L E N
VEGA ISD HIGH SCHOOL
SCALE: 1/8" = 1'-0"
SS
EE
OF
E
E
LEVEL 1 POWER PLAN - BID LOT #4
82984 G
IN
34
R
D1
36
PR
D
5
3
NORTH
R
JOHN F. HECK IV
L1B - 66
AREA B AREA A
A1
ENLARGED MECH 154
A3
SCALE: 1/4" = 1'-0"
LEVEL 1 POWER PLAN - AREA C SCALE: 1/8" = 1'-0"
0'
3.1 1
2
3
4
5
4'
8'
16'
NORTH
INE CH L MAT
2/15/2016 12:39:34 PM
NORTH
SHEET NO.
EP101C 6
1
2
3
4
5
6
GENERAL SHEET NOTES A. GFCI RECEPTACLES WILL BE INSTALLED AT ALL LOCATIONS AS REQUIRED BY THE LATEST VERSION OF NEC, STATE AND LOCAL CODES WHETHER INDICATED ON PLANS OR NOT. SOME LOCATIONS WILL BE WITHIN 6'-0" OF SINKS, EXTERIOR DOORS AND WET LOCATIONS. ALL EXTERIOR RECEPTACLE LOCATIONS WILL BE GFCI RATED AND WEATHERPROOF.
F
A3 / EP141B
L1A - 40
KEF-02
T F DH-01
L1A - 40 G
EP15 E
EP41
G
L1A - 40
R2.9
G
EP41
3
ARCHITECT E O F T EX
A S
ST
AT
John Heck 2016.02.15 13:54:11-07'00'
KEYNOTES
RV
D
E
IS T E R G IO N A L E N
IN
OF
E
SS
EE
R
PR
E
D
82984 G
R
JOHN F. HECK IV
PROJECT EP15
XRB
EP41
RU
EP47
REFER TO SHEET E701 FOR ADDITIONAL ELECTRICAL CONNECTION REQUIREMENTS. REFER TO SHEET M701 FOR MECHANICAL / ELECTRICAL INFORMATION. RECEPTACLE IS GFCI AND WEATHER PROOF AND WILL BE PART OF UNIT. CONTRACTOR WILL PROVIDE CIRCUIT INDICATED. BID LOT #3 IN DASHED AREA.
RS
R5
RR RQ RP C
RN RTU-27
EP15 G
RM
EP41
M0A - 13,15,17 L0A - 80
RK
B
200 Longhorn Street Vega, TX 79092
VEGA ISD HIGH SCHOOL
R6
RT
RJ 141B
EP47
EP A3 /
RG
5
ALL KEYNOTE NUMBERS HAVE BEEN REVISED ON THIS SHEET
RF
Addendum 004 REVISIONS 4
02/05/16
ADDENDUM #02
5
02/15/16
ADDENDUM #04
RE
KEY PLAN - N.T.S.
RD
DRAWN BY REVIEWED BY AREA C
RB
JMM
EXISTING DATE
02.15.2016
PROJECT NO:
RA
A
KIS
14-0424.002
DRAWING NAME
MATCH LINE
ROOF ELECTRICAL PLAN - AREA A
AREA B AREA A
A3
1
2
3
ROOF ELECTRICAL PLAN - AREA A SCALE: 1/8" = 1'-0"
0'
4
5
4'
8'
16'
NORTH
INE CH L MAT
2/15/2016 12:40:21 PM
NORTH
SHEET NO.
EP141A 6
1
2
3
4
5
6
GENERAL SHEET NOTES A. GFCI RECEPTACLES WILL BE INSTALLED AT ALL LOCATIONS AS REQUIRED BY THE LATEST VERSION OF NEC, STATE AND LOCAL CODES WHETHER INDICATED ON PLANS OR NOT. SOME LOCATIONS WILL BE WITHIN 6'-0" OF SINKS, EXTERIOR DOORS AND WET LOCATIONS. ALL EXTERIOR RECEPTACLE LOCATIONS WILL BE GFCI RATED AND WEATHERPROOF.
10
E
12
A3 / EP141C
A3 / EP141C
J
11
GEF-02
F
GEF-01
F
T
T K - 53
RTU-15
K - 51
EP15
M1A - 1,3,5 G L1B - 91
EP41 RTU-13 M1A - 7,9,11
EP15
H
F
K - 57
K - 55
F
L1A - 68,70,72
G.9
T
EP41
M1A - 37,39,41 T
F
L1A - 40
GEF-03
GEF-04
GEF-05
G
L1A - 58
T
EP42 M1A - 8,10,12
MAU-01
RTU-17
EP15 M1A - 2,4,6
L1A - 42 OF
SS
KEYNOTES
EP41 EP15
L1A - 52
M1A - 25,27,29
RR
CU-07
RTU-19
EP15
EP41
EP15
T
EP41
M1A - 19,21,23 L1A - 48
EF-05
F
L1A - 44 G
EP15
EP42
EP45
RQ
L1A - 64,66
RTU-24
EP15
EP42 EP43 EP45
F
FA08
EF-03
EP15
F T
L1A - 42
E
RTU-18
EP15 M1A - 43,45,47
EP42
CU-05
EP45
RTU-20
EP45
EP42
D.2
M1A - 14,16,18
D
RTU-26A
L1A - 59,61
EP15
CU-04
G
12
CU-03
EP15
G L1A - 44
L1A - 44
L1A - 42 G
EP15
EP41
RP
M1A - 38,40,42
EP41
M1A - 31,33,35
EP15
G
L1A - 44 G
EP41
RTU-23A
EP41
EP15
RTU-25
REFER TO SHEET E701 FOR ADDITIONAL ELECTRICAL CONNECTION REQUIREMENTS. REFER TO SHEET M701 FOR MECHANICAL / ELECTRICAL INFORMATION. RECEPTACLE IS GFCI AND WEATHER PROOF AND WILL BE PART OF UNIT. CONTRACTOR WILL PROVIDE CIRCUIT INDICATED. PEDESTAL MOUNTED DISCONNECT SWITCH. REFER TO DETAIL A3 ON SHEET E501. ROOF PEDESTAL MOUNTED RECEPTACLE. REFER TO DETAIL B5 ON SHEET E501. EXTEND POWER CIRCUIT TO FAN COIL UNIT INSIDE OF BUILDING. REFER TO SHEET E701 FOR ADDITIONAL INFORMATION. DUCT DETECTOR PROVIDED BY DIVISION 28, INSTALLED BY DIVISION 23, AND WIRED BY DIVISION 26/28.PROVIDE INDICATOR LIGHTIN CEILING TO IDENTIFY THIS DEVICE IF DETECTOR IS MOUNTED IN DUCTS IN CEILING SPACE.
EP15
EP15
EP41
L1A - 67,69
EP42
EP45 M1A - 20,22,24 L1A - 63,65
L1A - 60,62 L1A - 54 EF-06
EP42
EP45
T
F
M1A - 26,28,30
CU-06
EP15
EP15 RTU-21
R
EP15
L1A - 46 M1A - 49,51,53
200 Longhorn Street Vega, TX 79092
PROJECT
EP41
FA08
D
IS T E R G IO N A L E N
John Heck 2016.02.15 13:54:29-07'00'
L1A - 40 G
C
G
L1A - 40 G
EP15
A3 / EP141A
E
E
T F DH-01
82984
R
KEF-02
PR
EP15
T F
A
JOHN F. HECK IV
G
RTU-14
E
K - 49
G
L1A - 40
EP41
E O F T EX
AT
EE
EP15
EP41
S
M1A - 13,15,17
D
L1A - 42
RTU-16
IN
EP15
K - 61
ARCHITECT
G
VEGA ISD HIGH SCHOOL
K - 59
T
EP43
EP15
KEF-01
ST
GEF-06 F
G
G L1A - 46
EP41 EP41
RTU-22 EF-04
EP15
T F
RTU-23B
EP15
M1A - 32,34,36
C
EP15
L1A - 50
EP41
FA08
M1A - 44,46,48 L1A - 46 G
B
EP41
L1A - 46 G
5
ALL KEYNOTE NUMBERS HAVE BEEN REVISED ON THIS SHEET
RTU-26B
EP15
EP15
EF-09
F T
B
L1A - 56
A
Addendum 004 REVISIONS 4
02/05/16
ADDENDUM #02
5
02/15/16
ADDENDUM #04
KEY PLAN - N.T.S. R9 R7 R5
11
R8.1 DRAWN BY REVIEWED BY
R6
AREA C
DATE
JMM 02.15.2016
PROJECT NO:
R3
KIS
EXISTING
20
R2.9
A
R8
9
14-0424.002
DRAWING NAME
MATCH LINE
ROOF ELECTRICAL PLAN - AREA B
AREA B AREA A
A3
1
2
3
ROOF ELECTRICAL PLAN - AREA B SCALE: 1/8" = 1'-0"
0'
4
5
4'
8'
16'
NORTH
INE CH L MAT
2/15/2016 12:41:48 PM
NORTH
SHEET NO.
EP141B 6
1
2
3
4
5
6
GENERAL SHEET NOTES 1.9
2
3
4
A. GFCI RECEPTACLES WILL BE INSTALLED AT ALL LOCATIONS AS REQUIRED BY THE LATEST VERSION OF NEC, STATE AND LOCAL CODES WHETHER INDICATED ON PLANS OR NOT. SOME LOCATIONS WILL BE WITHIN 6'-0" OF SINKS, EXTERIOR DOORS AND WET LOCATIONS. ALL EXTERIOR RECEPTACLE LOCATIONS WILL BE GFCI RATED AND WEATHERPROOF.
5 5.1
E
M1B - 37,39,41
RTU-01B G
L1B - 92
0.5
EP41
M1B - 31,33,35
1
1.9
2
3
4
5 5.1
RTU-01A G
L1B - 92
EP15
EP15
EP41
Z
Z
Y.9
Y.9 ARCHITECT E O F T EX
AT
M1B - 1,3,5 G
SCALE: 1/8" = 1'-0"
0'
4'
8'
16'
SS
IS T E R G IO N A L E N
Y RTU-03
John Heck 2016.02.15 13:54:51-07'00'
KEYNOTES
M1B - 7,9,11
EP15
D
E
G
EE
OF
ROOF ELECTRICAL PLAN - BID LOT #4
E
E
D1
EP41
82984
R
PR
NORTH
R
JOHN F. HECK IV
L1B - 89
IN
EP15
D
A S
ST
RTU-02
PROJECT
G
EP15
L1B - 89
EP41
EP41 EP42 EP43 EP45
X
REFER TO SHEET E701 FOR ADDITIONAL ELECTRICAL CONNECTION REQUIREMENTS. REFER TO SHEET M701 FOR MECHANICAL / ELECTRICAL INFORMATION. RECEPTACLE IS GFCI AND WEATHER PROOF AND WILL BE PART OF UNIT. CONTRACTOR WILL PROVIDE CIRCUIT INDICATED. PEDESTAL MOUNTED DISCONNECT SWITCH. REFER TO DETAIL A3 ON SHEET E501. ROOF PEDESTAL MOUNTED RECEPTACLE. REFER TO DETAIL B5 ON SHEET E501. EXTEND POWER CIRCUIT TO FAN COIL UNIT INSIDE OF BUILDING. REFER TO SHEET E701 FOR ADDITIONAL INFORMATION.
VEGA ISD HIGH SCHOOL
M1B - 13,15,17
EP15 G
L1B - 89
EP41
RTU-05
M1B - 19,21,23
EP15 L1B - 89
W.2
G
EP41
EP43
W.1 F
F
EF-01
T
W
C
EP15
EP15
CU-01
CU-02
L1B - 70
RTU-06 M1B - 25,27,29
EP15
V
G L1B - 89
EP45
EP45
EP41
L1B - 97,99
L1B - 93,95
U
EP42 EP41
M1B - 2,4,6
RTU-07
EP41
EP15
200 Longhorn Street Vega, TX 79092
RTU-04
L1B - 89 G M1B - 8,10,12
T
RTU-08
L1B - 74
EF-08
EP15
F
L1B - 91
T
EF-10
G
F
T
L1B - 76
EP41 M1B - 14,16,18
S
RTU-09
EP15
B
G L1B - 91
EP41
R
5
ALL KEYNOTE NUMBERS HAVE BEEN REVISED ON THIS SHEET
M1B - 20,22,24
Q
RTU-10
EP15 G
P
Addendum 004 REVISIONS 4
02/05/16
ADDENDUM #02
5
02/15/16
ADDENDUM #04
L1B - 91
EP41
N
KEY PLAN - N.T.S. EF-11
F T
M
M1B - 26,28,30 L1B - 78 RTU-11
EP41
EP15
DRAWN BY
L
KIS
L1B - 91 REVIEWED BY
G
JMM
AREA C DATE
M1B - 32,34,36 L1B - 72
EF-07
PROJECT NO:
RTU-12
F
A
EP41
EP15
T
ROOF ELECTRICAL PLAN - AREA C
G
A3 / EP141B
A3 / EP141B
14-0424.002
DRAWING NAME
MATCH LINE
L1B - 91
J
02.15.2016
AREA B AREA A
A3
1
2
3
ROOF ELECTRICAL PLAN - AREA C SCALE: 1/8" = 1'-0"
0'
4
5
4'
8'
16'
NORTH
INE CH L MAT
2/15/2016 12:41:55 PM
NORTH
SHEET NO.
EP141C 6
1
2
3
4
5
6
GENERAL SHEET NOTES IT IS THE INTENT OF THESE DOCUMENTS TO SHOW A BASIC REPRESENTATION OF THE FIRE ALARM SYSTEM. DEVICES INDICATED ON THESE DOCUMENTS ARE IN NO WAY IMPLIED TO BE COMPREHENSIVE OF THE FINAL DESIGN. IT IS THE RESPONSIBILITY OF THE FIRE ALARM CONTRACTOR TO PROVIDE A DESIGN/BUILD FIRE ALARM SYSTEM BASED UPON A THOROUGH REVIEW OF ALL CONTRACT DOCUMENTS. IT IS THE RESPONSIBILITY OF THE FIRE ALARM CONTRACTOR TO ENSURE THAT THE FIRE ALARM SYSTEM IS CODE COMPLIANT, MEETS THE REQUIREMENTS OF THE AHJ AND COMPREHENSIVELY COVERS AND INCLUDES ALL NECESSARY PARTS AND LABOR ASSOCIATED WITH OTHER TRADES AND SYSTEMS IMPACTING THE FIRE ALARM SYSTEM. NO CHANGE ORDERS SHALL BE APPROVED FOR THE BASE SCOPE OF WORK.
A. REFER TO SHEET E603 FOR FIRE ALARM RISER DIAGRAM. B. ALL STROBES IN CORRIDORS AND COMMON AREAS WILL FLASH AT THE SAME TIME. C. ALL FIRE ALARM DEVICES IN GYMS WILL BE PROVIDED WITH A PROTECTIVE SHIELD.
E
ARCHITECT
R9 ST
FA03
RS
R
D
E
EE
IN
IS T E R G IO N A L E N
John Heck 2016.02.15 13:55:29-07'00'
RR
P
RQ
ELEC B121
FILM ROOM B107
P
RP R/F
R/F
JANITOR B115 GIRLS COACH B108 COACH RR B109
FA02
R/F P FATC0
ELEC B117
P
FA05 CORRIDOR B106
S FS T
FA03 FA05
P
R/F
RN
ELEV 714
P
B1 E501
BOYS COACH B119
RM
UNIFORM STOR B120 P
RK
STAIR 1 713
FILM ROOM B118
200 Longhorn Street Vega, TX 79092
TRAINING B116
UNIFORM STOR B114 GIRLS VARSITY B111
FA05
FIRE ALARM TERMINAL CABINET (FATC). REFER TO FIRE ALARM RISER DIAGRAM ON SHEET E603 FOR ADDTIONAL INFORMATION. COORDINATE FLOW AND TAMPER SWITCH LOCATION WITH PLUMBING DRAWINGS. PROVIDE INDICATOR LIGHT TO INDICATE LOCATION OF FLOW AND TAMPER SWITCHES THAT ARE ABOVE THE CEILING. DEVICES TO BE MOUNTED AT BOTTOM OF ELEVATOR PIT.
VEGA ISD HIGH SCHOOL
GIRLS JV B113
GIRLS B112
A A100 F / A3
S
OF
SS
PROJECT FA02
RT
C
G
KEYNOTES
20
R3
E
R5
82984
R
E
R6
D
A
JOHN F. HECK IV
XRB
PR
R7
R8
E O F T EX
AT
F BOYS JV B124
RJ
BOYS VARSITY B122
STOR B103
BOYS B123 P
R/F
RG
B
RF CORRIDOR B132 5
BOYS VISITOR B131
HALL B100B
ALL KEYNOTE NUMBERS HAVE BEEN REVISED ON THIS SHEET
RE
5
GIRLS VISITOR B133 OFFICIALS B128
PUMP ROOM B130
Addendum 004 REVISIONS 4 4
02/05/16
ADDENDUM #02
5
02/15/16
ADDENDUM #04
KEYPLAN
A A100 F / A3
OFFICIALS RR B129
DRAWN BY REVIEWED BY DATE LEVEL 1 ABOVE
R2.9
A
KIS JMM 02.15.2016
PROJECT NO:
14-0424.002
DRAWING NAME
LOWER LEVEL FIRE ALARM PLAN - AREA B
AREA B AREA A
A3
1
2
3
LOWER LEVEL FIRE ALARM PLAN - AREA B SCALE: 1/8" = 1'-0"
0'
4
5
4'
8'
16'
NORTH
INE CH L MAT
2/15/2016 12:51:47 PM
NORTH
SHEET NO.
FA100B 6
GENERAL SHEET NOTES IT IS THE INTENT OF THESE DOCUMENTS TO SHOW A BASIC REPRESENTATION OF THE FIRE ALARM SYSTEM. DEVICES INDICATED ON THESE DOCUMENTS ARE IN NO WAY IMPLIED TO BE COMPREHENSIVE OF THE FINAL DESIGN. IT IS THE RESPONSIBILITY OF THE FIRE ALARM CONTRACTOR TO PROVIDE A DESIGN/BUILD FIRE ALARM SYSTEM BASED UPON A THOROUGH REVIEW OF ALL CONTRACT DOCUMENTS. IT IS THE RESPONSIBILITY OF THE FIRE ALARM CONTRACTOR TO ENSURE THAT THE FIRE ALARM SYSTEM IS CODE COMPLIANT, MEETS THE REQUIREMENTS OF THE AHJ AND COMPREHENSIVELY COVERS AND INCLUDES ALL NECESSARY PARTS AND LABOR ASSOCIATED WITH OTHER TRADES AND SYSTEMS IMPACTING THE FIRE ALARM SYSTEM. NO CHANGE ORDERS SHALL BE APPROVED FOR THE BASE SCOPE OF WORK.
A. REFER TO SHEET E603 FOR FIRE ALARM RISER DIAGRAM. B. ALL STROBES IN CORRIDORS AND COMMON AREAS WILL FLASH AT THE SAME TIME. C. ALL FIRE ALARM DEVICES IN GYMS WILL BE PROVIDED WITH A PROTECTIVE SHIELD.
E
CONCESSION 127
G
A3 / FA101B F
R2.9 VEST 124
E O F T EX A
D
E
OF
E
D
IN
IS T E R E SS G IO N A L E N
EE
R
82984 G
R
JOHN F. HECK IV PR
FILM
RE SCO ER P E KE
AT
S
ST
ARCHITECT
John Heck 2016.02.15 13:58:27-07'00'
KEYNOTES PROJECT
RV
FA11
BLEACHER 200B
XRB
BID LOT #3. REFER TO SHEET FA102A FOR ADDITIONAL INFORMATION.
F
F
VEGA ISD HIGH SCHOOL
RT RS
TRACK 156
RR RQ RP
C
F
TRACK 156
RN
F
A
FAA
200 Longhorn Street Vega, TX 79092
RU
RM STAIR 2 169
RK
B
FA11
RJ
BLEACHERS 200A
5
RG
ALL KEYNOTE NUMBERS HAVE BEEN REVISED ON THIS SHEET
RF
Addendum 004 REVISIONS 3 4
02/05/16
ADDENDUM #02
5
02/15/16
ADDENDUM #04
KEYPLAN RE
FILM
RD F KIS
DRAWN BY REVIEWED BY AREA C
02.15.2016
DATE PROJECT NO:
RB A
14-0424.002
DRAWING NAME
MATCH LINE
RA
JMM
EXISTING
LEVEL 1 FIRE ALARM PLAN AREA A
AREA B AREA A
A3
1
2
3
LEVEL 1 FIRE ALARM PLAN - AREA A SCALE: 1/8" = 1'-0"
0'
4
5
4'
8'
16'
NORTH
INE CH L MAT
2/15/2016 12:54:09 PM
NORTH
SHEET NO.
FA101A 6
1
2
3
4
5
6
GENERAL SHEET NOTES 1.9
2
3
4
E
VEST
5
A. REFER TO SHEET E603 FOR FIRE ALARM RISER DIAGRAM. B. ALL STROBES IN CORRIDORS AND COMMON AREAS WILL FLASH AT THE SAME TIME. C. ALL FIRE ALARM DEVICES IN GYMS WILL BE PROVIDED WITH A PROTECTIVE SHIELD.
IT IS THE INTENT OF THESE DOCUMENTS TO SHOW A BASIC REPRESENTATION OF THE FIRE ALARM SYSTEM. DEVICES INDICATED ON THESE DOCUMENTS ARE IN NO WAY IMPLIED TO BE COMPREHENSIVE OF THE FINAL DESIGN. IT IS THE RESPONSIBILITY OF THE FIRE ALARM CONTRACTOR TO PROVIDE A DESIGN/BUILD FIRE ALARM SYSTEM BASED UPON A THOROUGH REVIEW OF ALL CONTRACT DOCUMENTS. IT IS THE RESPONSIBILITY OF THE FIRE ALARM CONTRACTOR TO ENSURE THAT THE FIRE ALARM SYSTEM IS CODE COMPLIANT, MEETS THE REQUIREMENTS OF THE AHJ AND COMPREHENSIVELY COVERS AND INCLUDES ALL NECESSARY PARTS AND LABOR ASSOCIATED WITH OTHER TRADES AND SYSTEMS IMPACTING THE FIRE ALARM SYSTEM. NO CHANGE ORDERS SHALL BE APPROVED FOR THE BASE SCOPE OF WORK.
5.1
F
A153
CLASSROOM
CLASSROOM
A151
A150
0.5
P STOR
CORRIDOR
P STOR
A151A
A152
A150A
Z
1
1.9
2
3
4
5 5.1
Z
Y.9
Y.9
FA13
F ARCHITECT
ST
SS
STOR 149A
STOR 148A
STOR 147A
STOR 146A
3
FA09
P FA13
CLASSROOM 147
COORDINATE FLOW AND TAMPER SWITCH LOCATION WITH PLUMBING DRAWINGS. PROVIDE INDICATOR LIGHT TO INDICATE LOCATION OF FLOW AND TAMPER SWITCHES THAT ARE ABOVE THE CEILING. REFER TO DETAIL C6 ON SHEET SF503 FOR ALL CONDUITS ROUTED THROUGH WALL IN DASHED AREA. REFER TO SHEET SERIES "MH" FOR LOCATION OF FIRE SMOKE DAMPERS OF DUCT DETECTOR LOCATIONS. PROVIDE INDICATED LIGHT AT CEILING LEVEL TO IDENTIFY LOCATION OF DEVICE. DEVICE WILL BE MOVED SHOULD BID LOT #4 BE ACCEPTED TO LOCATION INDICATED IN BID LOT #4 PLAN.
VEGA ISD HIGH SCHOOL
X
CLASSROOM 146
W.2
FA09
W.1 C
JAN 139
GIRLS 145
W
STAFF RR 143
V
R/F
IDF 141
P P
BOYS 144
STOR 137A
ELEC 150
CORRIDOR 138
R/F P
VEST 142
R/F
U
R
PROJECT FA03
FA10 P
John Heck 2016.02.15 13:59:01-07'00'
KEYNOTES
P
D
E
Y P
EE
IS T E R G IO N A L E N
IN
E
16'
G
F P
STOR 136A SPEC ED 137
200 Longhorn Street Vega, TX 79092
8'
OF
D
4'
E
0'
82984
R
SCALE: 1/8" = 1'-0"
JOHN F. HECK IV PR
D1
LEVEL 1 FIRE ALARM PLAN - BID LOT #4
CLASSROOM 148
A S
CLASSROOM 149
NORTH
E O F T EX
AT
CLASSROOM 136
T
S B
FA10
R
LAB 135
CLASSROOM 134
5
ALL KEYNOTE NUMBERS HAVE BEEN REVISED ON THIS SHEET
T
FA03 FS TS
Q
P
P
R/F
STOR/PREP 133
MECH 154
P P
STOR 134A
CORRIDOR 138
N
Addendum 004 REVISIONS 5 4
02/05/16
ADDENDUM #02
5
02/15/16
ADDENDUM #04
KEYPLAN
STOR 132A
T
P
M L
DRAWN BY
CLASSROOM 132
FA10
KIS
REVIEWED BY
JMM
AREA C DATE
LAB 131
02.15.2016
PROJECT NO:
A
DRAWING NAME
MATCH LINE
J
LEVEL 1 FIRE ALARM PLAN AREA C
CORRIDOR 138
A3 / FA101B
A3 / FA101B
14-0424.002
AREA B AREA A
A3
LEVEL 1 FIRE ALARM PLAN - AREA C SCALE: 1/8" = 1'-0"
0'
3.1 1
2
3
4
5
4'
8'
16'
NORTH
INE CH L MAT
2/15/2016 12:46:49 PM
NORTH
SHEET NO.
FA101C 6
1
2
3
4
5
6
GENERAL SHEET NOTES
Branch Panel: K A.I.C. Rating: 10,000 Mains Type: MLO Mains Rating: 400 A
EQUIPMENT NUMBER K-1 K-3 K-4 K-6 K-7 K-8 K-12 K-14 K-15 K-17 K-18 K-18A K-20 K-21 K-22 K-24
Notes:
E
2
KIT EQP #6 (OPEN AIR COOLER) KIT EQP #7 (30" REFRIGERATOR) KIT EQP #8 (30" FREEZER) KIT EQP #12 (KITCHEN HOOD) KIT EQP #14 (CHAR BROILER) SHUNT TRIP
20 A 20 A 20 A 20 A 20 A --
1 1 1 1 1 --
KIT EQP #15 (FRYER)
75 A
2
--
--
SHUNT TRIP
720 VA 1997 VA
20 A
180 VA
1080 VA
6032 VA
720 VA
720 VA
2250 VA 886 VA
180 VA
4800 VA
2250 VA
1500 VA 240 VA
1200 VA
1080 VA
696 VA
2250 VA
1500 VA 840 VA
1080 VA
1500 VA
696 VA
0 VA
696 VA
0 VA
180 VA
1500 VA
696 VA
0 VA 0 VA
0 VA
0 VA 0 VA
0 VA
0 VA
0 VA 0 VA
0 VA
0 VA
0 VA
0 VA
25690 VA 222 A
0 VA 0 VA 26273 VA 227 A
2
20 A
NC DRYER, STOR 129A
1 1 1 1
20 A 20 A 20 A 20 A
REC COOKING STATIONS, CLASSROOM 129 REC COOKING STATIONS, CLASSROOM 129 REC COOKING STATIONS, CLASSROOM 129 REC COOKING STATIONS, CLASSROOM 129
2
20 A
REC RANGE, CLASSROOM 129
1 1
20 A 20 A
NC EXHAUST HOOD, CLASSROOM 129 REC MICROWAVE, CLASSROOM 129
2
20 A
REC RANGE, CLASSROOM 129
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 ----
20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A ----
NC EXHAUST HOOD, CLASSROOM 129 REC MICROWAVE, CLASSROOM 129 REC REFRIGERATOR, CLASSROOM 129 REC FREEZER, CLASSROOM 129 NC EXHAUST HOOD, CLASSROOM 129 REC MICROWAVE, CLASSROOM 129 NC EXHAUST HOOD, CLASSROOM 129 REC MICROWAVE, CLASSROOM 129 SPARE SPARE SPARE SPARE SPARE SPARE SPARE SPARE SPARE SPARE SPARE SPARE SPARE SPACE ONLY SPACE ONLY SPACE ONLY
CKT 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 52 54 56 58 60 62 64 66 68 70 72 74 76 78 80 82 84
3/4" 1 1/2" 3/4" 3/4" 3/4" 3/4" 3/4"
ARCHITECT
E
EK02
EK04
Demand Factor 100.00% 100.00% 67.93% 65.00% 0.00%
Estimated Demand 5120 VA 4584 VA 18944 VA 21815 VA 0 VA
Panel Totals Total Conn. Load: Total Est. Demand: Total Conn. Current: Total Est. Demand Current:
A
SS
IS T E R G IO N A L E N
John Heck 2016.02.15 13:59:12-07'00'
PROJECT EK01
EK03
Connected Load 5120 VA 4584 VA 27888 VA 33561 VA 0 VA
82984 G
KEYNOTES
Legend:
Load Classification NC MTR REC KIT LTG
E O F T EX
AT
JOHN F. HECK IV OF
0 VA
0 VA
Circuit Description REC AUDIO/VISUAL, CLASSROOM 129 REC CLASSROOM 129 REC CLASSROOM 129 & STOR 129A REC SEWING MACHINES, CLASSROOM 129 REC SEWING MACHINES, CLASSROOM 129 REC WASHER, STOR 129A
S
1356 VA
Trip 20 A 20 A 20 A 20 A 20 A 20 A
RECEPTACLE RECEPTACLE RECEPTACLE HARDWIRE JUNCTION BOX RECEPTACLE RECEPTACLE HARDWIRE JUNCTION BOX RECEPTACLE HARDWIRE JUNCTION BOX HARDWIRE JUNCTION BOX HARDWIRE JUNCTION BOX HARDWIRE JUNCTION BOX HARDWIRE JUNCTION BOX RECEPTACLE RECEPTACLE RECEPTACLE
E
20 A 1 40 A 1 20 A 1 1800 VA 180 VA 20 A 1 20 A 1 20 A 1 1200 VA 1128 VA 20 A 1 20 A 1 20 A 1 696 VA 180 VA 20 A 1 20 A 1 20 A 1 696 VA 0 VA 20 A 1 20 A 1 20 A 1 408 VA 0 VA 20 A 1 20 A 1 20 A 1 0 VA 0 VA 20 A 1 20 A 1 20 A 1 0 VA 0 VA 20 A 1 20 A 1 --0 VA 0 VA ----Total Load: 19189 VA Total Amps: 160 A
Poles 1 1 1 1 1 1
3/4" 3/4" 3/4" 3/4" 3/4" 3/4" 3/4" 3/4"
R
KIT EQP #18A (DISHWASHER HOOD) KIT EQP #18 (DISHWASHER) KIT EQP #20 (ICE MACHINE) KIT EQP #21 (DRINK REFRIGERATOR) KIT EQP #22 (ICE CREAM STORAGE) KIT EQP #24 (PIZZA PREP) KIT WARMING KITCHEN 128 REC CONCESSION 127 & WARMING KITCHEN 128 MTR DH-01, ROOF MTR GEF-01, ROOF MTR GEF-02, ROOF MTR GEF-03, ROOF MTR GEF-04, ROOF MTR GEF-06, ROOF MTR KEF-02, ROOF SPARE SPARE SPARE SPARE SPARE SPARE SPARE SPARE SPACE ONLY SPACE ONLY SPACE ONLY
600 VA
2200 VA
3 886 VA
840 VA
720 VA
2250 VA 886 VA
KIT EQP #17 (DISPOSAL)
540 VA
1080 VA 6032 VA
0 VA
1997 VA
2200 VA 780 VA
0 VA
720 VA
720 VA 1320 VA
1128 VA
C
(2) #12 & (1) #12 GND (2) #12 & (1) #12 GND (3) #10 & (1) #10 GND (2) #12 & (1) #12 GND (2) #12 & (1) #12 GND (2) #12 & (1) #12 GND (2) #12 & (1) #12 GND (2) #12 & (1) #12 GND (3) #10 & (1) #10 GND (4) #12 & (1) #12 GND (3) #8 & (1) #10 GND (2) #12 & (1) #12 GND (2) #12 & (1) #12 GND (2) #12 & (1) #12 GND (2) #12 & (1) #12 GND (2) #12 & (1) #12 GND
R
30 A
B 960 VA
15 6 19.2 11 7 9.4 5 1.5 58 3.2 40 2 11.3 10 15 10
D
KIT EQP #4 (4-WELLS UNIT)
A 180 VA
1 1 1 1 1 1 1 1 1 3 1 1 1 1 1 1
E
Poles 1 1
120 120 208 120 120 120 120 120 208 208 120 120 120 120 120 120
EE
Trip 20 A 20 A
CASHIER STAND FROST TOP UNIT 4-WELLS UNIT OPEN AIR COOLER 30" REFRIGERATOR 30" FREEZER KITCHEN HOOD CHAR BROILER (WORK TABLE) FRYER (WORK TABLE) DISPOSAL (SOLID DISH TABLE) DISHWASHER DISHWASHER HOOD ICE MACHINE DRINK REFRIGERATOR ICE CREAM STORAGE PIZZA PREP
EQUIPMENT TERMINATION REQUIREMENTS
ST
Circuit Description KIT EQP #1 (CASHER STAND) KIT EQP #3 (FROST TOP UNIT)
EQUIPMENT DESCRIPTION
A. CONTRACTOR WILL BE RESPONSIBLE FOR REVIEWING THE KITCHEN EQUIPMENT SHOP DRAWINGS FOR ELECTRICAL CHARACTERISTIC DISCREPANCIES AS WELL AS ROUGH-INS, LOCATION AND SIZE. CONTRACTOR WILL NOTIFY THE ARCHITECT AND KITCHEN CONSULTANT IN WRITING PRIOR TO COMMENCEMENT OF ANY WORK. B. INFORMATION PROVIDED HEREIN (E401) IS FOR BIDDING PURPOSES AND DOES NOT REPRESENT EXACT INFORMATION AS DELIVERED TO THE PROJECT SITE. KITCHEN EQUIPMENT DOCUMENTS ("FS" SERIES) WILL GOVERN. CONTRACTOR WILL VERIFY EXACT REQUIREMENTS OF ALL EQUIPMENT AS DELIVERED TO PROJECT SITE AND WILL PROVIDE AND INSTALL ALL NECESSARY ATTACHMENTS AND ADJUSTMENTS THAT MAY BE REQUIRED. COORDINATE PRIOR TO COMMENCEMENT OF ANY WORK. C. CONTRACTOR WILL EXTEND ALL RACEWAYS AND CONDUCTORS AND PROVIDE AND INSTALL ALL ELECTRICAL EQUIPMENT AS REQUIRED BY: 1) PROJECT SPECIFICATION, 2) NEC (NFPA-70); STATE AND OR LOCAL CODES. CONTRACTOR WILL MAKE FINAL TERMINATION TO KITCHEN EQUIPMENT AS DIRECTED BY KITCHEN EQUIPMENT SUPPLIER/INSTALLER AND LEAVE IN OPERABLE AND COMPLETE CONDITION. D. REFER TO KITCHEN EQUIPMENT SPECIFICATIONS AND FS SHEET SERIES FOR ADDITIONAL EQUIPMENT CHARACTERISTICS AND INFORMATION FOR PROPER INSTALLATION OF KITCHEN AND ELECTRICAL EQUIPMENT AND ROUGH-IN. E. COORDINATE WITH FIRE SUPPRESSION INSTALLER FOR ALL REQUIRED CONNECTIONS. PROVIDE AND INSTALL ALL ELECTRICAL EQUIPMENT, RACEWAY AND CONDUCTORS AS DIRECTED. COORDINATE ALL TERMINATION TO SHUNT TRIP CIRCUIT BREAKERS, FIRE ALARM PANEL AND HOOD PRIOR TO ROUGH-IN. LEAVE SUPPRESSION SYSTEM IN A COMPLETE AND OPERABLE CONDITION. F. THROUGHOUT KITCHEN, ALL 15 AND 20 AMP, 120 VOLT RECEPTACLES, WHETHER OR NOT THE RECEPTACLE SERVES COUNTERTOP APPLIANCES, WILL BE 1 HP MOTOR RATED GFCI AND INSTALLED PER NEC 2014, ARTICLE 210.8B2. ALL DEVICES WILL BE MOUNTED SO EASY ACCESS TO DEVICE IS POSSIBLE. IF THEY ARE INSTALLED BEHIND LARGE EQUIPMENT, THEN BRANCH CIRCUIT WILL BE PROTECTED USING A GFCI TYPE OVERCURRENT PROTECTIVE DEVICE. G. PROVIDE PASS & SEYMOUR MODEL 2095 GFCI DEVICES AS INDICATED BY MANUFACTURER'S RECOMMENDATIONS. H. GFCI RECEPTACLES WILL BE INSTALLED AT ALL LOCATIONS AS REQUIRED BY THE LATEST VERSION OF NEC, STATE AND LOCAL CODES WHETHER INDICATED ON PLANS OR NOT. SOME LOCATIONS WILL BE WITHIN 6'-0" OF SINKS, EXTERIOR DOORS AND WET LOCATIONS. ALL EXTERIOR RECEPTACLE LOCATIONS WILL BE GFCI RATED AND WEATHERPROOF.
PR
D
CKT 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 51 53 55 57 59 61 63 65 67 69 71 73 75 77 79 81 83
EQUIPMENT LOAD CHARATERISTICS BRANCH CIRCUIT CONDUIT CONDUCTOR DESCRIPTION SIZE AMPS VOLTAGE PHASE
IN
120/208 Wye 3 4 84
EK05
71153 VA 50463 VA 198 A 140 A
CIRCUITS WITHIN DASHED AREA ARE FED FROM PANEL "K" UNLESS NOTED OTHERWISE
EK07
EK08 G 24
Notes:
G 20
J
G
K - 34,36
18
G 18
K - 38
EP01
EP39
EP40
EP01
EP39
C
EP11 G 22 K - 40
20
4
6
EP04
EP01
20
EP01
18
EK09
K-2
EP21
EP11 EP01
2
G
K - 26,28
K - 30
EP21
G
G 22
J
K - 32
6
G
4
CLASSROOM 129
EP03 24 G
EP12
10 EK10
K - 42
EP05
EP01 G 22
K - 44 G
8
EP03
K - 48 24 G
EP01
18
EP03 20
EP01
K - 52
6 G
EP01 G
EP40
EP39
K - 46
EP01
EP39
18 G
J
10
EP04
STOR 129A
18
K - 50
EP01
20 22 G
4
EP11
EP11
H
G 20 G
8
24 G
J
10
8
8
10
EP05 EP07 EP11
G.9
EP12 EP21
4
2448
G
EK05
EK09
G
K−7
G K - 47
G K - 47
K - 39
EK05
K - 11
EK02
K−12
K−24
K - 43
K−14
WARMING KITCHEN 128
K−4
K−3
EK01 EK03 EK07 J
K - 17 K−15 K - 21,23
5
ALL KEYNOTE NUMBERS HAVE BEEN REVISED ON THIS SHEET
K−1
K-3
K - 37
K−20
K-1
J
G
EK01
J
DEVICE IS FOR WALL MOUNTED SHORT-THROW PROJECTOR MOUNTED IN MULTI-SERVICE BOX. REFER TO MOUNTING DETAILS ON SHEET SERIES “T” FOR ADDITIONAL INSTALLATION INFORMATION. MOUNT DEVICE AT 48” A.F.F FOR FREEZER, PROVIDE DEDICATED CIRCUIT. WASHER & DRYER ARE STACKED ONE ON TOP OF THE OTHER. RECEPTACLES WILL BE MOUNTED AT 18" A.F.F. AND 36" A.F.F., PROVIDE DEDICATED CIRCUITS. DEVICE IS FOR MICROWAVE. COORDINATE ROUGH-IN HEIGHT WITH EQUIPMENT INSTALLER. REFER TO SHEET AE222 FOR ADDITIONAL INFORMATION. MOUNT DEVICE AT 48” A.F.F FOR REFRIGERATOR, PROVIDE DEDICATED CIRCUIT. MOUNT DEVICE AT 30” FOR RANGE, PROVIDE DEDICATED CIRCUIT. CONTRACTOR WILL MATCH NEMA CONFIGURATION OF RECEPTACLE WITH UNIT PLUG. COORDINATE PRIOR TO ORDERING RECEPTACLE DEVICE. DEVICE IS FOR EXHAUST HOOD ABOVE RANGE. COORDINATE ROUGH-IN HEIGHT WITH EQUIPMENT INSTALLER. CONTROL SWITCH FOR EXHAUST HOOD ABOVE RANGE. COORDINATE ROUGH-IN HEIGHT WITH EQUIPMENT INSTALLER.
K - 15
K - 13
K - 5,7 K−6
2448
EK08
HOOD MOUNT CONTROL FOR EXHAUST FROM MECHANICAL EQUIPMENT.CONTROL WILL BE WITH PILOT LIGHT TYPE SWITCH TO INDICATE WHEN THE HOOD IS ON. REFER TO "FS" DRAWINGS FOR EXACT LOCATION AND ADDITIONAL TERMINATION REQUIREMENTS. MOUNT DEVICE 6" ABOVE COUNTER TOP BACK SPLASH, TABLE TOP OR SINK. RECEPTACLE WILL BE GFCI RATED. MOUNTING HEIGHTS TO BE COORDINATED WITH ARCHITECT PRIOR TO COMMENCEMENT OF ANY WORK. REFER TO CASEWORK DETAILS INDICATED ON "A" SHEET SERIES FOR MOUNTING OF DEVICE IN OR ON CASEWORK. CONDUIT WILL STUB THROUGH WALL OR FLOOR AND INTO DEVICE. MOUNTING HEIGHTS TO BE COORDINATED WITH ARCHITECT PRIOR TO COMMENCEMENT OF ANY WORK IF HEIGHTS ARE NOT INDICATED IN CASE WORK DETAILS.
K - 45
K−8
K - 45 G
EP40
EK03 EK07
J
G K - 45
EK02
EK02
K-9
G K - 45
G
EK05
EK05
STOR 128B
K−21
2472
2472
2472
K - 47
EP39
EK02
EP07 K - 12
B
K - 45
K - 14,16
STOR 128A
UNIT WILL BE HARD-WIRE CONNECTED WITH WATER-TIGHT FLEX CONDUIT. PROVIDE 6'-0" OF FLEX FOR MOVEMENT OF UNITS FOR CLEANING. CIRCUIT BREAKER IN PANEL WILL ACT AS UNIT DISCONNECTING MEANS. UNIT WILL INCORPORATE A PLUG AND CORD. CONTRACTOR WILL MATCH NEMA CONFIGURATION OF RECEPTACLE WITH UNIT PLUG PER "FS" DRAWINGS OR MANUFACTURER'S RECOMMENDATIONS COORDINATE PRIOR TO ORDERING RECEPTACLE DEVICE. PANEL CIRCUIT BREAKER WILL BE USED AS DISCONNECTING MEANS FOR THIS UNIT. PROVIDE LOCK OUT / TAG OUT CIRCUIT BREAKER. PROVIDE A PEDESTAL RECEPTACLE FOR UNIT. DEVICE WILL BE MOUNTED 2" ABOVE FINISHED FLOOR. PROVIDE HUBBELL LO-CON SERIES (SC3098A / SS309B) OR APPROVED EQUAL DEVICE PROVIDED WILL BE COORDINATED WITH KITCHEN EQUIPMENT INSTALLER FOR PROPER DEVICE AND DEVICE PLATES. MOUNT DEVICE(S) 6" ABOVE COUNTER TOP BACKSPLASH, TABLE TOP, OR SINK DEVICE WILL BE GFCI RATED. THIS PIECE OF EQUIPMENT WILL AUTOMATICALLY SHUT OFF WHEN FIRE SUPPRESSION SYSTEM DETECTS A PROBLEM. CIRCUIT BREAKER WILL BE SHUNT TRIP TYPE. JUNCTION BOX FOR HOOD LIGHTS. MAKE ALL CONNECTIONS TO EXHAUST AND HOOD LUMINAIRES PER MANUFACTURER'S RECOMMENDATIONS. HOOD LUMINAIRES WILL BE PART OF HOOD PACKAGE. LOCATE SWITCH CONTROL PER ARCHITECT'S RECOMMENDATIONS. JUNCTION BOX WILL BE FOR FIRE SUPPRESSION CONNECTION TO FIRE ALARM PANEL AND SHUNT TRIP CIRCUIT BREAKERS. KITCHEN EQUIPMENT UNDER HOOD WILL AUTOMATICALLY SHUT DOWN IN THE EVENT OF AN EMERGENCY. ALL ELECTRICAL CIRCUIT BREAKERS WILL BE SHUNT TRIP TYPE AND CONNECTED TO SUPPRESSION AND FIRE ALARM SIGNAL. THE KEC WILL PROVIDE FIRE SUPPRESSION WITH HOOD AND HOOD SHOP DRAWINGS. THIS WILL ALSO INCLUDE DIAGRAMS AND TERMINATION REQUIREMENTS. REFER TO "FS" DRAWINGS. COORDINATE WITH KEC FOR REQUIREMENTS PRIOR TO COMMENCMENT OF ANY WORK. REFER TO SHEET E603 FOR MORE FIRE ALARM INFORMATION. POWER WILL ALSO SERVE CONTROL PANEL AT IT'S FINAL INSTALLED LOCATION. COORDINATE GAS SOLENOID VALVE REQUIREMENTS WITH PLUMBING AND PROVIDE ADEQUATE TERMINATION TO FIRE ALARM SYSTEM.
200 Longhorn Street Vega, TX 79092
Volts: Phases: Wires: Spaces:
WARMING KITCHEN 128 LDP0A Surface Type 1
VEGA ISD HIGH SCHOOL
Location: Supply From: Mounting: Enclosure:
ELECTRICAL KITCHEN EQUIPMENT SCHEDULE
EK02 EK04
K
K - 47
K - 45
EK01
G
G
Addendum 004 REVISIONS 4
02/05/16
ADDENDUM #02
5
02/15/16
ADDENDUM #04
J
EK02 EK04
G
EK02
K - 27,29,31
EK01 K−22
K - 41 K−18A
CONCESSION 127 K - 47 G
G K - 47
K - 35 K - 33
J
KEYPLAN
K−17
EK10
K−18
J
G
J
DRAWN BY
EK01 EK08
REVIEWED BY DATE PROJECT NO:
0.5
A
1.9
2
3
3.1
JMM 02.15.2016 14-0424.002
DRAWING NAME
ENLARGED CONCESSION KITCHEN 128, HOME EC 129 & STORAGES
ENLARGED CONCESSION KITCHEN 128, HOME EC 129 & STORAGES SCALE: 1/4" = 1'-0"
2/15/2016 12:59:32 PM
A3
1
Author
SHEET NO.
E401 1
2
3
4
5
6
1
2
3
4
5
6
LUMINAIRE TYPE AS INDICATED ON LUMINAIRE SCHEDULE
FIXTURE POLE AND BASE PLATE FURNISHED AS INTEGRAL PART OF FIXTURE
FUSE BOX AT BASE OF POLE
BASE COVER
E
BUSH CONDUIT ENDS
5
NO. 12 GAUGE WIRE HANGER TO BUILDING FRAMING OR STRUCTURAL MEMBERS. SUSPEND FROM EACH END OF FIXTURE. CEILING SYSTEM HANGER WIRES (TYP.)
2'-6"
12"X12"X12" HANDHOLE
FINISH GRADE
GRADE
CONDUIT FEEDER. SEE UTILITY / SITE PLAN FOR ROUTING (2)1"C
18" BELOW CEILING (MINIMUM) REFER TO SHEET EL-101 FOR EXACT MOUNTING HEIGHT
NOTE: 1. POLE BASE DETAILS SHOWS INSTALLATION OF RACEWAY PATHS FOR POLE POWER AND GROUNDING ONLY. CONCRETE, REBAR AND MOUNTING SHALL BE SPECIFIED/APPROVED BY THE STRUCTURAL ENGINEER. REFER TO SHEET SERIES "AS" FOR ADDITIONAL INFORMATION.
ARCHITECT
S
POLE BASE DETAIL
SS
R
D
E
G
IS T E R G IO N A L E N
EE
OF
SCALE: NONE
D5
E
E
LINEAR DIRECT-INDIRECT SUPPORT DETAIL
82984
R
D3
A
JOHN F. HECK IV PR
D
E O F T EX
AT
ST
2. HAND HOLE NEAR POLE BASE WILL BE A 12"x12"x12" VEHICULAR RATED FOR 15k LBS. WITH A TAMPER PROOF COVER LABELED "LIGHTING". QUAZITE OR APPROVED EQUAL.
IN
CEILING SUSPENSION SYSTEM (TYP.)
John Heck 2016.02.15 13:59:23-07'00'
SCALE: NO SCALE PROJECT
CEILING SYSTEM HANGER WIRES (TYP.)
INSIDE
ELECTRIC DOOR OPERATOR AT TOP OF DOOR FRAME
3/4"C. DO
ELECTRIC OPERATOR
NO. 12 GAUGE WIRE HANGER TO BUILDING FRAMING OR STRUCTURAL MEMBERS). SUSPEND FROM ALL FOUR CORNERS OF FIXTURE.
OUTSIDE
VEGA ISD HIGH SCHOOL
DRILLED HOLE IN FRAME AND CONDUIT FOR PNEUMATIC TUBE
PUSHBUTTON
DOOR FRAME DOOR STOP
TO OTHER PUSHBUTTONS AS NECESSARY (1/2"C.)
~
DOOR
INSIDE ELEVATION VIEW
CEILING SYSTEM HANGER WIRES (TYP.)
PLAN VIEW
DO=ADA DOOR OPERATOR ABOVE ACCESSIBLE CEILING OR IN SERVICE ROOM. ALL CONDUIT NOT IN SERVICE ROOM SHALL BE CONCEALED. REFER TO PLAN DRAWINGS FOR OUTLET BOX LOCATIONS OR COORDINATE CONTROL DEVICE REQUIREMENTS WITH SYSTEM SUPPLIER IF NOT SHOWN. ALL OUTLETS TO BE 1-GANG VERTICAL AND +46" UNLESS OTHERWISE NOTED. COORDINATE OUTLET LOCATIONS AND CONDUCTOR TYPES PRIOR TO COMMENCEMENT OF ANY WORK WITH ARCHITECT AND HARDWARE MANUFACTURER.
C
C3
HANDICAP DOOR SYSTEM DETAIL SCALE: NO SCALE
LAY-IN LUMINAIRE
LUMINAIRE SUPPORT DETAIL
C5
SCALE: NO SCALE
CAST METAL "WHILE-IN-USE" WATERPROOF COVER(S) & RECEPTACLE(S)
1" CONDUIT & CONNECTOR 4" SQUARE, 2-1/8" DEEP (4SD-1" BOX) JUNCTION BOX WITH KNOCKOUTS.
SMOKE DETECTOR CONNECTED TO FIRE ALARM SYSTEM
ELEVATOR MOTOR/CONTROLLER
TELECOM OUTLET FOR CAR PHONE/COMM.
CB
"ELEVATOR CAB" 120VAC CIRCUIT
SECTION "A-A"
120VAC CIRCUIT P
P
GFI
R/F
ELEVATOR MOTOR/CONTROLLER 480VAC/3PHASE CIRCUIT
B
RIGID STEEL 3/4" CONDUIT FOR WIRING
GFI P
F1
12" MAX
FB816 BRACKET
J
CAST METAL, 2-GANG, NEMA 3R JUNCTION BOX WITH THREADED HUBS
RIGID STEEL CONDUIT FOR SUPPORT PER N.E.C. ART. 314
SMOKE & HEAT DETECTORS AT PIT
DISCONNECT CB, LOCKABLE
SEISMIC FIXTURE CLAMPS: REQUIRED AT ALL (4) LUMINAIRE CORNERS WITH (2) #10 SELF-TAPPING SCREWS. AGI SEISMIC PRODUCTS OR EQUAL. AC 184 COMPLIANT.
R/F
P
PANEL LP
SMOKE DETECTOR AT EACH LOBBY
2-GANG JUNCTION BOX
SMOKE & HEAT DETECTORS AT TOP OF SHAFT
3/4" CONDUIT ELEVATION NOTE: REFER TO STRUCTURAL AND ARCHITECTURAL DRAWINGS FOR SECURELY ATTATCHING TO ROOF STRUCTURE AND FLASHING
MAIN POWER DISCONNECT SWITCH SHUNT TRIP TYPE, LOCKABLE. BUSSMAN POWER MODULE # PS-3-T48-R2-K-G-N6-B-F1
B3
OUTLET BOX IN CMU BLOCK DETAIL SCALE: NO SCALE
RECEPTACLE ROOF MOUNTING DETAIL
B5
Addendum 004
SCALE: NO SCALE
REVISIONS 1
REFERENCES: A. B. C. D. E.
200 Longhorn Street Vega, TX 79092
CONDUIT TO CONTROLLER
NEC 620 (ELEVATORS). NFPA 72: (RECALL OPERATION) & (ELEVATOR SHUTDOWN). ASME/ANSI 17.1 (SAFETY CODE FOR ELEVATORS). NFPA 101 (HIGH RISE / STANDBY POWER). UFC 3003 (EMERGENCY OPERATIONS).
4
02/05/16
ADDENDUM #02
5
02/15/16
ADDENDUM #04
A
DISCONNECT. REFER TO PLANS FOR SIZE.
NOTES:
B. C. D.
ALL INFORMATION HAS BEEN BASED ON KONE TRACTION TYPE ELEVATOR. DIFFERENT EQUIPMENT MAY HAVE DIFFERENT REQUIREMENTS. COORDINATE ELEVATOR MOTOR SIZE WITH OWNER OR ARCHITECT. ALL JUNCTION AND DEVICE BOXES IN THE ELEVATOR SHAFT, PIT, AND MACHINE ROOM ARE TO BE WEATHER-PROOF. ALL DEVICE BOXES IN THE ELEVATOR SHAFT, PIT, AND MACHINE ROOM ARE TO HAVE WEATHER-PROOF WHILE-IN-USE COVERS.
A
12" MAX
A.
RIGID STEEL 2" STRUT SUPPORT PER N.E.C. ART. 314
RIGID STEEL 3/4" CONDUIT FOR WIRING
COPPER BUS BAR (REFER TO DIAGRAM AND KEYED NOTE ON SHEET E-602.)
DRAWN BY
KIS
REVIEWED BY SECTION "A-A"
JMM
DATE
02.15.2016
PROJECT NO: STAND-OFFS
NOTE:
A
BOLT CONNECTION WITH COMPRESSION SPADE LUG FITTING (TYPICAL)
ELEVATOR PHASE I & II RECALL SEQUENCE OF OPERATION SHALL BE SO THE APPROPRIATE SMOKE SENSOR SHALL ACTIVATE FIREFIGHTERS SERVICE PHASE I RECALL OPERATION. THE ELEVATOR SHALL RETURN TO THE DESIGNATED FLOOR LEVEL AND REMAIN OPEN WITHOUT RESPONDING TO ANY OTHER HALLWAY OR CAR PUSH BUTTONS.
14-0424.002
DRAWING NAME
ELECTRICAL DETAILS
2-GANG JUNCTION BOX 3/4" CONDUIT ELEVATION 2700V INSULATORS
2/15/2016 1:07:03 PM
NOTE: REFER TO STRUCTURAL AND ARCHITECTURAL DRAWINGS FOR SECURELY ATTATCHING TO ROOF STRUCTURE AND FLASHING
ELEVATOR TYPICAL DETAILS
A1
A3
SCALE: SCALE: NONE
1
2
3
UNISTRUT MOUNTED DISCONNECT DETAIL SCALE: NO SCALE
4
TO SERVICE ENTRANCE GROUND
MAIN GROUNDING ELECTRODE BUS BAR DETAIL
A5
E501
SCALE: NO SCALE
5
SHEET NO.
6
1
2
3
4
5
6
GENERAL SHEET NOTES Neutral LIGHTING CONTROL DESCRIPTION Scene (A) 50% Light Level of Gym Floor Luminaires or Manual-ON/Auto-OFF Scene (B) 100% Light Level of Gym Floor Luminaires or Manual-ON/Auto-OFF Scene (C) 50% Light Level of Mezzanine Luminaires or Manual-ON/Auto-OFF Scene (D) 100% Light Level of Mezzanine Luminaires or Manual-ON/Auto-OFF Scene (E) 100% Light Level of Gym Floor Luminaires & 50% Light Level of Mezzanine Luminaires or Manual-ON/Auto-OFF
B.
Gym Luminaires
ROOM CONTROLLER LMRC-212
a = FLOOR - 50% LIGHT LEVEL
E
b = FLOOR - 100% LIGHT LEVEL Hot
Hot
120/277
120/277
1
LMPC-100
LMPC-100
LMPC-100
2
Five Button Switch LMSW-105
LMPC-100
c = MEZZANINE - 50% LIGHT LEVEL
c = MEZZANINE - 50% LIGHT LEVEL d = MEZZANINE - 100% LIGHT LEVEL e = SPORTING EVENTS FLOOR - 100% LIGHT LEVEL & MEZZANINE - 50% LIGHT LEVEL
Five Button Switch LMSW-105
d = MEZZANINE - 100% LIGHT LEVEL
LIGHTING CONTROL DESCRIPTION PLACARD
LIGHTING CONTROL DESCRIPTION PLACARD
MOUNT ADJACENT TO FIVE BUTTON SWITCHES
MOUNT ADJACENT TO TWO BUTTON SWITCHES
CAT5e LMRJ-Watt Stopper Cable
LMPC-100
DIAGRAMS ARE SHOWN FOR BIDDING PURPOSES. CONTRACTOR WILL PROVIDE ACCURATE AND COORDINATED DIAGRAMS FOR SHOP DRAWING SUBMITTALS. CONTRACTOR WILL PROVIDE ENGRAVED SWITCHES AND A PLACARD WITH CONTROL DESCRIPTION. PLACARD WILL BE PER ARCHITECTURAL REQUIREMENTS, PLACARD WILL BE NO LARGER THAN A SWITCH COVER PLATE.
Mezzanine Luminaires
CAT5e LMRJ-Watt Stopper Cable
ROOM CONTROLLER LMRC-212
LMPC-100
A.
Two Button Switch LMSW-102
Two Button Switch LMSW-102
Two Button Switch LMSW-102
Two Button Switch LMSW-102
Two Button Switch LMSW-102
Two Button Switch LMSW-102
c
c
c
c
c
c
d
d
d
d
d
d
Watt Stopper
Watt Stopper
Watt Stopper
Watt Stopper
Watt Stopper
Watt Stopper
LIGHTING SEQUENCE OF OPERATION b
SCALE: NO SCALE B.
Neutral
Neutral
Lighting Load (a) LIGHTING CONTROL DESCRIPTION Load (a) ALL Inboard Lamps = Manual-ON/Auto-OFF Load (b) ALL Outboard Lamps = Manual-ON/Auto-OFF
Lighting Load (a) LIGHTING CONTROL DESCRIPTION Load (a) ALL Inboard Lamps = Manual-ON/Auto-OFF Load (b) ALL Outboard Lamps = Manual-ON/Auto-OFF
Lighting Load (b)
Lighting Load (b)
5
a = INNER LAMPS
Hot
a = INNER LAMPS
Hot
120/277
120/277 b = OUTER LAMPS
b = OUTER LAMPS
ROOM CONTROLLER LMRC-212
C.
ROOM CONTROLLER LMRC-212 D.
C
LIGHTING CONTROL DESCRIPTION PLACARD
LIGHTING CONTROL DESCRIPTION PLACARD
MOUNT ADJACENT TO SWITCHES
MOUNT ADJACENT TO SWITCHES
E. CAT5e LMRJ-Watt Stopper Cable
CAT5e LMRJ-Watt Stopper Cable
Two Button Switch LMSW-102
LMDC-100
Lighting Loads (a), (b)
Two Button Switch LMSW-102
LMDC-100
Lighting Loads (a), (b)
a
b Watt Stopper
SEE INSTALLATION INSTRUCTIONS FOR TERMINATION TYPE.
F.
a
E.
b Watt Stopper
SEE INSTALLATION INSTRUCTIONS FOR TERMINATION TYPE.
RJ45 (TYPICAL)
RJ45 (TYPICAL)
F. G.
REFER TO SHEET SERIES "EL" FOR QUANTITIES AND ADDITIONAL INFORMATION
B2
REFER TO SHEET SERIES "EL" FOR QUANTITIES AND ADDITIONAL INFORMATION
WATT STOPPER "DLM" WIRING DIAGRAM
B4
SCALE: NO SCALE
WATT STOPPER "DLM" WIRING DIAGRAM
OF
WATT STOPPER "DLM" WIRING DIAGRAM
E
E
D1
A
G
SS
R
D
82984
R
D
E O F T EX
AT
JOHN F. HECK IV PR
REFER TO SHEET SERIES "EL" FOR QUANTITIES AND ADDITIONAL INFORMATION
ARCHITECT
S
RJ45 (TYPICAL)
CLASSROOMS (VARIOUS ROOMS WILL HAVE DIFFERING CONTROL LOADS. SEE DIAGRAMS AND ROOMS FOR ADDITIONAL INFORMATION. INFORMATION BELOW IS TYPICAL: 1. UNOCCUPIED MODE: WHEN ROOM IS UNOCCUPIED, ALL LIGHTING SHALL BE DISABLED AND DE-ENERGIZED BY OCCUPANCY SENSOR(S) IN ROOM. 2. OCCUPIED MODE: a. LIGHTING CONTROL IN ROOM WILL BE ENABLED BY SWITCHES IN ROOM. NO LUMINAIRES WILL AUTOMATICALLY ENERGIZE. b. DURING OCCUPANCY AT THREE BUTTON SWITCH: - TOP BUTTON (a) WILL CONTROL INBOARD LAMP OF LUMINAIRES IN FRONT OF CLASSROOM. - MIDDLE BUTTON (b) WILL CONTROL INBOARD LAMP OF LUMINAIRES IN BACK OF CLASSROOM - BOTTOM BUTTON (c) WILL CONTROL OUTBOARD LAMPS OF LUMINAIRES IN ENTIRE CLASSROOM. c. WHEN PERSONNEL LEAVE THE ROOM AND OCCUPANCYSENSOR TIMES OUT, THE SYSTEM SHALL RESET TO THE UNOCCUPIED MODE. GYMNASIUM: 1. UNOCCUPIED MODE: WHEN ROOM IS UNOCCUPIED, ALL LIGHTING SHALL BE DISABLED AND DE-ENERGIZED BY OCCUPANCY SENSORS IN ROOM. 2. OCCUPIED MODE: a. LIGHTING CONTROL IN ROOM WILL BE ENABLED BY SWITCHES IN ROOM. NO LUMINAIRES WILL AUTOMATICALLY ENERGIZE. b. DURING OCCUPANCY AT FIVE BUTTON SWITCH: - FIRST BUTTON (a) WILL CONTROL GYM FLOOR LUMINAIRES TO 50% LIGHT LEVEL. - SECOND BUTTON (b) WILL CONTROL GYM FLOOR LUMINAIRES TO 100% LIGHT LEVEL. - THIRD BUTTON (c) WILL CONTROL MEZZANINE LUMINAIRES TO 50% LIGHT LEVEL. - FOURTH BUTTON (d) WILL CONTROL MEZZANINE LUMINAIRES TO 100% LIGHT LEVEL. - FIFTH (LARGE) BUTTON (e) WILL CONTROL SPORTS LIGHTING TO 100% LIGHT LEVEL OF LUMINAIRES OVER COURT AND 50% LIGHT LEVEL OF LUMINAIRES OVER MEZZANINE. c. DURING OCCUPANCY AT TWO BUTTON SWITCH: - TOP BUTTON (c) WILL CONTROL MEZZANINE LUMINAIRES TO 50% LIGHT LEVEL. - BOTTOM BUTTON (d) WILL CONTROL MEZZANINE LUMINAIRES TO 100% LIGHT LEVEL. 3. WHEN PERSONNEL LEAVE THE ROOM AND OCCUPANCY SENSOR TIMESOUT, THE SYSTEM SHALL RESET TO THE UNOCCUPIED MODE. LOCKER ROOMS: DUAL TECHNOLOGY (ULTRASONIC/INFRARED) CEILING MOUNTED SENSOR WILL CONTROL LUMINAIRES ON AND OFF AUTOMATICALLY. KEYED SWITCH WILL BE SECONDARY MEANS OF CONTROL RESTROOMS, SMALL AND LARGE: DUAL TECHNOLOGY (ULTRASONIC/INFRARED) CEILING MOUNTED SENSOR WILL CONTROL LUMINAIRES ON AND OFF AUTOMATICALLY. KEYED SWITCH WILL BE SECONDARY MEANS OF CONTROL. STORAGE & JANITOR ROOMS: WALL MOUNTED VACANCY SENSOR WILL CONTROL THE LUMINAIRE(S) IN THE ROOM. OFFICES: 1. UNOCCUPIED MODE: WHEN ROOM IS UNOCCUPIED, ALL LIGHTING SHALL BE DISABLED AND DE-ENERGIZED BY VACANCY SENSOR IN ROOM. 2. OCCUPIED MODE: a. LIGHTING CONTROL IN ROOM WILL BE ENABLED BY SWITCHES IN ROOM. NO LUMINAIRES WILL AUTOMATICALLY ENERGIZE. b. WHEN PERSONNEL LEAVE THE ROOM AND VACANCY SENSOR TIMES OUT, THE SYSTEM SHALL RESET TO THE UNOCCUPIED MODE. CORRIDORS, STAIRWELLS AND COMMON AREAS: 1. LOCAL CONTROL OF LUMINAIRES WILL BE VIA A KEYED MOMENTARY SWITCH. 2. OVERALL CONTROL WILL BE PROGRAMMED ON AT 5 AM AND OFF AT 11 PM. 3. OVERRIDE SWITCH TO OPERATE PROGRAMMED CONTROL BETWEEN 11 PM AND 5 AM. OVERRIDE WILL TURN LIGHTS ON FOR 30 MINUTE INCREMENTS. EXTERIOR BUILDING LIGHTING: 1. ALL EXTERIOR BUILDING LIGHTING WILL BE PROGRAMMED TO COME ON A 1/2 HOUR BEFORE DUSK AND OFF A 1/2 HOUR AFTER DAWN. SITE LIGHTING: 1. ROADWAY LIGHTING WILL BE PROGRAMMED TO COME ON A 1/2 HOUR BEFORE DUSK AND OFF A 1/2 HOUR AFTER DAWN. 2. PARKING LOT AREA LIGHTING WILL BE PROGRAMMED TO COME ON A 1/2 HOUR BEFORE DUSK AND OFF A 1/2 HOUR AFTER DAWN. 3. WALKWAY LIGHTING WILL COME ON A 1/2 HOUR BEFORE DUSK AND OFF A 1/2 HOUR AFTER DAWN.
E
Watt Stopper
A.
IS T E R G IO N A L E N
EE
d
IN
c
d Watt Stopper
SEE INSTALLATION INSTRUCTIONS FOR TERMINATION TYPE.
e
c
John Heck 2016.02.15 13:59:42-07'00'
PROJECT
200 Longhorn Street Vega, TX 79092
b
VEGA ISD HIGH SCHOOL
e
a
ST
a
SCALE: NO SCALE
Neutral Neutral
Neutral
Lighting Load (a)
B LIGHTING CONTROL DESCRIPTION Load (a) ALL Inboard Lamps = Manual-ON/Auto-OFF Load (b) ALL Outboard Lamps = Manual-ON/Auto-OFF
Lighting Load (a) LIGHTING CONTROL DESCRIPTION Load (a) Inboard Lamps for Front of Room = Manual-ON/Auto-OFF Load (b) Inboard Lamps for Back of Room = Manual-ON/Auto-OFF Load (c) ALL Outboard Lamps = Manual-ON/Auto-OFF
Lighting Load (b)
Lighting Load (b)
Lighting Load (a) LIGHTING CONTROL DESCRIPTION Load (a) Inboard Lamps for Front of Room = Manual-ON/Auto-OFF Load (b) Inboard Lamps for Back of Room = Manual-ON/Auto-OFF Load (c) ALL Outboard Lamps = Manual-ON/Auto-OFF
Lighting Load (b) Lighting Load (c)
Lighting Load (c)
a = INNER LAMPS
Hot 120/277
Hot
Hot
120/277
120/277
Hot
Hot
120/277
120/277
ROOM CONTROLLER LMRC-212
b = OUTER LAMPS ROOM CONTROLLER LMRC-212
ROOM CONTROLLER LMRC-212
ROOM CONTROLLER LMRC-212
a = FRONT CLASS SINGLE LAMP
Addendum 004 REVISIONS 5
02/15/16
ADDENDUM #04
ROOM CONTROLLER LMRC-212
b = BACK CLASS SINGLE LAMP
LIGHTING CONTROL DESCRIPTION PLACARD MOUNT ADJACENT TO SWITCHES
c = ENERGY SAVINGS CAT5e LMRJ-Watt Stopper Cable
CAT5e LMRJ-Watt Stopper Cable
CAT5e LMRJ-Watt Stopper Cable
DRAWN BY
LIGHTING CONTROL DESCRIPTION PLACARD
LMDC-100
MOUNT ADJACENT TO SWITCHES
LMDC-100
LMDC-100
Two Button Switch LMSW-102 Lighting Loads (a), (b)
A
a
b Watt Stopper
SEE INSTALLATION INSTRUCTIONS FOR TERMINATION TYPE.
Two Button Switch LMSW-102 Lighting Loads (a), (b)
LMDC-100
Three Button Switch LMSW-103 Lighting Loads (a), (b) & (c)
a
b Watt Stopper
Three Button Switch LMSW-103 Lighting Loads (a), (b) & (c)
b c Watt Stopper
SEE INSTALLATION INSTRUCTIONS FOR TERMINATION TYPE.
RJ45 (TYPICAL)
a
b = BACK CLASS SINGLE LAMP
b
RJ45 (TYPICAL)
c = ENERGY SAVINGS
PROJECT NO:
c Watt Stopper
SEE INSTALLATION INSTRUCTIONS FOR TERMINATION TYPE.
RJ45 (TYPICAL)
a
2/15/2016 1:11:34 PM
A1
02.15.2016 14-0424.002
LIGHTING DIAGRAMS & SEQUENCE OF OPERATION
MOUNT AT ENTRY DOOR ADJACENT TO SWITCH.
REFER TO SHEET SERIES "EL" FOR QUANTITIES AND ADDITIONAL INFORMATION
WATT STOPPER "DLM" WIRING DIAGRAM
A2
SCALE: NO SCALE
1
JMM
DRAWING NAME LIGHTING CONTROL DESCRIPTION PLACARD
REFER TO SHEET SERIES "EL" FOR QUANTITIES AND ADDITIONAL INFORMATION REFER TO SHEET SERIES "EL" FOR QUANTITIES AND ADDITIONAL INFORMATION
KIS
REVIEWED BY DATE
b
Watt Stopper
Three Button Switch LMSW-103 Lighting Loads (a), (b) & (c)
a
c
a = FRONT CLASS SINGLE LAMP
2
WATT STOPPER "DLM" WIRING DIAGRAM SCALE: NO SCALE
3
WATT STOPPER "DLM" WIRING DIAGRAM
A4
SHEET NO.
E604
SCALE: NO SCALE
4
5
6
1
2
3
4
Branch Panel: L1A Location: Supply From: Mounting: Enclosure:
A.I.C. Rating: 18,000 Mains Type: MLO Mains Rating: 400 A
120/208 Wye 3 4 126
Location: Supply From: Mounting: Enclosure:
Volts: Phases: Wires: Spaces:
ELEC 150 HDP1B Surface Type 1
A.I.C. Rating: 18,000 Mains Type: 400A MCB Mains Rating: 400 A
120/208 Wye 3 4 126
Notes:
1
REC STUDENT COMMONS 102 REC STUDENT COMMONS 102 & TABLE STOR 164 LTG PENDANT IN CENTER OF COVE, STUDENT COMMONS 102 NC MOTORIZED DOOR OPERATORS, VEST 124 NC MOTORIZED DOOR OPERATORS, CORRIDOR 110 NC MOTORIZED DOOR OPERATORS, VEST 101 REC EXTERIOR
20 A 20 A 20 A 20 A 20 A 20 A 20 A
1 1 1 1 1 1 1
20 A
2
MTR CU-03 / FC-03, ROOF
15 A
2
MTR CU-04 / FC-04, ROOF
15 A
2
MTR CU-05 / FC-05, ROOF
15 A
2
SPARE SPARE SPARE SPARE SPARE SPARE SPARE SPARE SPARE SPARE SPARE SPARE SPARE SPARE SPARE SPARE SPARE SPACE ONLY SPACE ONLY SPACE ONLY SPACE ONLY SPACE ONLY SPACE ONLY SPACE ONLY SPACE ONLY SPACE ONLY SPACE ONLY SPACE ONLY
20 A 1 20 A 1 20 A 1 20 A 1 20 A 1 20 A 1 20 A 1 20 A 1 20 A 1 20 A 1 20 A 1 20 A 1 20 A 1 20 A 1 20 A 1 20 A 1 20 A 1 ----------------------Total Load: Total Amps:
1800 VA
720 VA 1800 VA
960 VA
900 VA 1080 VA
5760 VA
1200 VA 5760 VA
180 VA
1200 VA 696 VA
1200 VA 180 VA
100 VA
600 VA 1080 VA
720 VA 900 VA
900 VA
720 VA 210 VA
720 VA 1740 VA
960 VA
696 VA 960 VA
696 VA 900 VA
200 VA
408 VA 500 VA
696 VA 1352 VA
1352 VA
1352 VA 1352 VA
1352 VA 1352 VA
1352 VA
924 VA 0 VA 0 VA 0 VA 0 VA 0 VA 0 VA 0 VA 0 VA 0 VA 0 VA 0 VA 0 VA 0 VA 0 VA 0 VA
0 VA
0 VA 0 VA
0 VA 0 VA
0 VA
0 VA
0 VA 0 VA
0 VA
0 VA
0 VA 0 VA
0 VA
0 VA
0 VA 0 VA
0 VA
0 VA
0 VA 0 VA
0 VA
0 VA
0 VA 0 VA
0 VA
0 VA
0 VA 0 VA
0 VA
2
20 A
MTR CU-07 / FC-07, ROOF
3
15 A
MTR MAU-01, ROOF
924 VA
0 VA 0 VA
0 VA
MTR CU-06 / FC-06, ROOF
924 VA 1352 VA
0 VA
1352 VA
20 A
0 VA
0 VA 0 VA
18328 VA 153 A
0 VA
27398 VA 240 A
0 VA 0 VA 27692 VA 242 A
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 ------------
20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A ------------
SPARE SPARE SPARE SPARE SPARE SPARE SPARE SPARE SPARE SPARE SPARE SPARE SPARE SPARE SPARE SPARE SPACE ONLY SPACE ONLY SPACE ONLY SPACE ONLY SPACE ONLY SPACE ONLY SPACE ONLY SPACE ONLY SPACE ONLY SPACE ONLY SPACE ONLY
Legend:
5
Circuit Description REC AUDIO/VISUAL, CLASSROOM 149 REC CLASSROOM 149 REC CLASSROOM 149 & STOR 149A REC AUDIO/VISUAL, CLASSROOM 147 REC CLASSROOM 147 REC CLASSROOM 147 & STOR 147A REC JAN 139, STAFF RR 143, BOYS 144, GIRLS 145 & ELEC 150 NC NORTH WALL, IDF 141 NC SOUTH WALL, IDF 141 NC WEST WALL, IDF 141 NC TWISTLOCK ABOVE RACK, IDF 141 NC QUAD ABOVE RACK, IDF 141 NC TWISTLOCK ABOVE RACK, IDF 141 NC QUAD ABOVE RACK, IDF 141 REC AUDIO/VISUAL, SPEC ED 137 REC SPEC ED 137 REC SPEC ED 137 & STOR 137A REC AUDIO/VISUAL, LAB 135 REC STOR/PREP 133 & LAB 135 REC STOR/PREP 133 & LAB 135 REC TABLES, LAB 135 REC TABLES, LAB 135 REC TABLES, LAB 135 REC FUME HOOD, LAB 135 REC MICROSCOPE CHARGING CABINET, LAB 135 REC GOGGLE CABINET, LAB 135 REC ISIMET CONTROL PANEL, LAB 135 REC REFRIGERATOR, STOR/PREP 133 REC DISHWASHER, STOR/PREP 133 REC STOR/PREP 133 REC AUDIO/VISUAL, LAB 131 REC LAB 131 & STOR/PREP 133 REC LAB 131, STOR/PREP 133 & MECH 154 REC TABLES, LAB 131 REC TABLES, LAB 131 REC TABLES, LAB 131 REC FUME HOOD, LAB 131 REC GOGGLE CABINET, LAB 131 REC MICROSCOPE CHARGING CABINET, LAB 131 REC ISIMET CONTROL PANEL, LAB 131 REC DWH-1, MECH 154 REC DWH-2, MECH 154 MTR UH-01, MECH 154 REC EXTERIOR REC ROOF MOUNTED REC ROOF MOUNTED
Trip 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 30 A 20 A 30 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A
Poles 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
MTR CU-01 / FC-01, ROOF
20 A
2
MTR CU-02 / FC-02, ROOF
20 A
2
SPARE SPARE SPARE SPARE SPARE SPARE SPARE SPARE SPARE SPARE SPARE SPARE SPARE
20 A 1 20 A 1 20 A 1 20 A 1 20 A 1 20 A 1 20 A 1 20 A 1 20 A 1 20 A 1 20 A 1 20 A 1 20 A 1 Total Load: Total Amps:
A 1140 VA
B 1140 VA 900 VA
1140 VA
540 VA
1500 VA
2200 VA
1500 VA
1500 VA
600 VA
600 VA
2250 VA 1140 VA
180 VA
1560 VA
900 VA
1140 VA 720 VA
1080 VA
900 VA
540 VA
2250 VA 1500 VA
540 VA
900 VA
2200 VA 2496 VA
2496 VA
900 VA
135 VA 1500 VA
1500 VA
900 VA
960 VA 900 VA
900 VA
C
900 VA
1140 VA 900 VA
900 VA 900 VA
900 VA
900 VA
1140 VA 900 VA
900 VA 180 VA
180 VA
180 VA 600 VA
696 VA
600 VA
900 VA
1080 VA
900 VA
1352 VA
0 VA
0 VA
0 VA
0 VA
0 VA
0 VA
0 VA
0 VA
0 VA
360 VA 0 VA
0 VA 0 VA
0 VA 0 VA
0 VA 0 VA
0 VA 0 VA
0 VA
180 VA
900 VA
0 VA 0 VA
696 VA
900 VA
0 VA 0 VA
900 VA 696 VA
1352 VA 0 VA
2280 VA
696 VA
1352 VA 1352 VA
1080 VA
200 VA
1140 VA 720 VA
1080 VA
600 VA
1140 VA 600 VA
360 VA
180 VA
600 VA
696 VA 180 VA
180 VA
900 VA
1740 VA 900 VA
180 VA
180 VA
180 VA 1080 VA
900 VA
900 VA
1080 VA 1800 VA
1560 VA
900 VA
1140 VA
0 VA
0 VA 0 VA
33669 VA 282 A
0 VA
30462 VA 256 A
0 VA 0 VA 29124 VA 243 A
Poles 1 1 1 1 1 1 1 1
Trip 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A
Circuit Description REC AUDIO/VISUAL 132 REC CLASSROOM 132 REC CLASSROOM 132 & STOR 132A REC AUDIO/VISUAL, LIFESKILLS 130 REC LIFE SKILLS 130 & RR 130A REC LIFE SKILLS 130 & 130B EQP EF-02, RR 130A REC WASHER, LIFESKILLS 130
2
20 A
NC DRYER, LIFESKILLS 130
1 1
20 A 20 A
REC REFRIGERATOR, LIFESKILLS 130 REC MICROWAVE, LIFESKILLS 130
2
20 A
NC RANGE, LIFESKILLS 130
1 1 1 1 1
20 A 20 A 20 A 20 A 20 A
REC EXHAUST HOOD, LIFESKILLS 130 REC AUDIO/VISUAL, CLASSROOM 148 REC CLASSROOM 148 REC CLASSROOM 148 & STOR 148A REC AUDIO VISUAL, CLASSROOM 146
1
20 A
REC CLASSROOM 146
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A
REC CLASSROOM 146 & STOR 146A REC AUDIO/VISUAL, CLASSROOM136 REC CLASSROOM 136 REC CLASSROOM 136 & STOR 136A REC AUDIO/VISUAL, CLASSROOM 134 REC CLASSROOM 134 REC CLASSROOM 134 & STOR 134A REC CORRIDORS B134 & 138 REC WATER COOLER, CORRIDOR 138 REC WATER COOLER, CORRIDOR 138 REC PRINTER, CORRIDOR 138 MTR FIRE/SMOKE DAMPERS, CORRIDOR 138 NC MOTORIZED DOOR OPERATORS, VEST 153 NC MOTORIZED DOOR OPERATORS, VEST 142 MTR EF-01, ROOF MTR EF-07, ROOF MTR EF-08, ROOF MTR EF-10, ROOF MTR EF-11, ROOF BID LOT #4 - REC AUDIO/VISUAL, CLASSROOM A151 BID LOT #4 - REC CLASSROOM A151 BID LOT #4 - REC CLASSROOM A151 & STOR A151A BID LOT #4 - REC AUDIO/VISUAL, CLASSROOM A150 BID LOT #4 - REC CLASSROOM A150 BID LOT #4 - REC CLASSROOM A150 & STOR A150A BID LOT #4 - REC ROOF MOUNTED SPARE SPARE SPARE SPARE SPARE SPARE SPARE SPARE SPARE SPARE SPARE SPARE SPARE SPARE SPARE SPARE SPARE
CKT 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 52 54 56 58 60 62 64 66 68 70 72 74 76 78 80 82 84 86 88 90 92 94 96 98 100 102 104 106 108 110 112 114 116 118 120 122 124 126
ARCHITECT
Connected Load 17176 VA 27648 VA 28200 VA 394 VA
Demand Factor 100.00% 100.00% 67.73% 125.00%
Estimated Demand 17176 VA 27648 VA 19100 VA 493 VA
Panel Totals Total Conn. Load: Total Est. Demand: Total Conn. Current: Total Est. Demand Current:
73418 VA 64417 VA 204 A 179 A
Notes:
Load Classification NC MTR REC
Connected Load 25592 VA 9583 VA 58080 VA
Demand Factor 100.00% 100.00% 58.61%
Estimated Demand 25592 VA 9583 VA 34040 VA
E
82984 G
SS
IS T E R G IO N A L E N
John Heck 2016.02.15 13:59:53-07'00'
PROJECT
Panel Totals Total Conn. Load: Total Est. Demand: Total Conn. Current: Total Est. Demand Current:
A
JOHN F. HECK IV
Legend:
Load Classification NC MTR REC LTG
E O F T EX
AT
R
20 A
360 VA
CKT 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 51 53 55 57 59 61 63 65 67 69 71 73 75 77 79 81 83 85 87 89 91 93 95 97 99 101 103 105 107 109 111 113 115 117 119 121 123 125
D
REC STUDENT COMMONS 102
720 VA
CKT 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 52 54 56 58 60 62 64 66 68 70 72 74 76 78 80 82 84 86 88 90 92 94 96 98 100 102 104 106 108 110 112 114 116 118 120 122 124 126
E
1 1 1 1
1080 VA
Circuit Description REC BELOW NORTH COUNTERS SEATING AREA, GYMNASIUM... REC BELOW NORTH COUNTERS SEATING AREA, GYMNASIUM... REC BELOW NORTH COUNTERS SEATING AREA, GYMNASIUM... REC BELOW SOUTH COUNTERS SEATING AREA, GYMNASIUM... REC BELOW SOUTH COUNTERS SEATING AREA, GYMNASIUM... REC BELOW SOUTH COUNTERS SEATING AREA, GYMNASIUM... REC BELOW WEST COUNTER, TRACK 156 REC BELOW WEST COUNTER, TRACK 156 REC BELOW WEST COUNTER, TRACK 156 REC TRACK 156 REC TRACK 156 REC TRACK 156 & STAIR 2 169 MTR BASKETBALL GOAL, GYMNASIUM B100-2 MTR BASKETBALL GOAL, GYMNASIUM B100-2 MTR BASKETBALL GOAL, GYMNASIUM B100-2 MTR BASKETBALL GOAL, GYMNASIUM B100-2 MTR BASKETBALL GOAL, GYMNASIUM B100-2 MTR BASKETBALL GOAL, GYMNASIUM B100-2 NC SCOREBOARD, GYMNASIUM B100-2 REC ROOF MOUNTED REC ROOF MOUNTED REC ROOF MOUNTED REC ROOF MOUNTED MTR EF-03, ROOF MTR EF-04, ROOF MTR EF-05, ROOF MTR EF-06, ROOF MTR EF-09, ROOF MTR GEF-05, ROOF
EE
20 A 20 A 20 A 20 A
1080 VA
Trip 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A
IN
REC EXHAUST BLOWER, KILN 123B NC COILING DOOR, CORRIDOR 138 REC MICROWAVE, CORRIDOR 138 MTR FIRE/SMOKE DAMPERS, CORRIDOR 138
720 VA
Poles 1 1 720 VA 1 1 1 720 VA 1 1 1 540 VA 1 1 1 900 VA 1 1 1 1200 VA 1 1 1 1200 VA 1 1 1 720 VA 1 1 1 696 VA 1 1 1 864 VA 1 1 1 1352 VA 2
93255 VA 69215 VA 259 A 192 A
200 Longhorn Street Vega, TX 79092
2
1080 VA
C
VEGA ISD HIGH SCHOOL
20 A
B
S
NC ELECTRIC KILN, KILN 123B
NC LANDSCAPE CONTROLLER / HEAT TAPE, EXTERIOR
Poles A 1 600 VA 720 VA 1 1 1 1080 VA 720 VA 1 1 1 360 VA 720 VA 1 1 1 184 VA 900 VA 1 1 1 900 VA 1200 VA
OF
Trip 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A 20 A
E
Circuit Description REC AUDIO/VISUAL, MEDIA CENTER 125 REC MEDIA CENTER 125 & STOR 125A REC MEDIA CENTER 125 & STOR 125A REC MEDIA CENTER 125 & STOR 125A REC MEDIA CENTER 125 & STOR 125A REC FLOOR BOX, MEDIA CENTER 125 REC FLOOR BOX, MEDIA CENTER 125 REC COPIER, MEDIA CENTER 125 REC COPIER, MEDIA CENTER 125 LTG PENDANT LIGHTING, MEDIA CENTER 125 REC AUDIO/VISUAL, ART 123 REC ART 123 & KILN 123B REC ART 123 & STOR 123A
R
C
Volts: Phases: Wires: Spaces:
ELEC 117A LDP0A Surface Type 1
PR
D
Branch Panel: L1B
Notes:
CKT 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 51 53 55 57 59 61 63 65 67 69 71 73 75 77 79 81 83 85 87 89 91 93 95 97 99 101 103 105 107 109 111 113 115 117 119 121 123 125
6
ST
E
5
Notes:
B
Addendum 004 REVISIONS 5
KEY PLAN
N.T.S.
02/15/16
ADDENDUM #04
DRAWN BY
KIS
REVIEWED BY
JMM
DATE
02.15.2016
PROJECT NO:
14-0424.002
DRAWING NAME
A
L1B
2/15/2016 1:17:41 PM
L1A
ELECTRICAL PANEL SCHEDULES
SHEET NO.
E703 1
2
3
4
5
6
1
2
3
4
5
GENERAL SHEET NOTES A.
ALL EXIT SIGNS, TYPES "E" OR "EG", WILL BE CONNECTED TO CIRCUIT SERVING THE ROOM THEY ARE LOCATED IN AND FROM NO OTHER CIRCUIT. REFER TO SHEET E700a FOR ELECTRICAL LUMINAIRE SCHEDULE. REFER TO SHEET EP101 FOR ELECTRICAL ROOMS AND ELECTRICAL EQUIPMENT LAYOUT. REFER TO SHEET E500a FOR LIGHTING DIAGRAMS AND SEQUENCE OF OPERATION. REFER TO DETAIL D2 ON SHEET E500a FOR LUMINAIRE MOUNTING. REFER TO ARCHITECTURAL SHEET SERIES "AE" FOR ADDITIONAL CEILING GRID MOUNTING SUPPORT INFORMATION. ALL LUMINAIRES WILL BE SECURELY SUPPORTED SEPARATELY FROM CEILING GRIDS TO CEILING STRUCTURE. REFER TO ARCHITECTURAL SHEETS FOR EXTERIOR LIGHTING ELEVATIONS. ALL EXTERIOR BUILDING LUMINAIRES WILL BE ROUTED THROUGH A TIME CLOCK AND CONTACTOR LOCATED IN THE ELECTRICAL ROOM WHERE THE PANEL FEEDING THOSE LUMINAIRES IS LOCATED. REFER TO DIAGRAM D1 ON SHEET E500a FOR ADDITIONAL INFORMATION. ALL LUMINAIRES IN DASHED AREA WILL BE CONNECTED TO CIRCUIT INDICATED UNLESS OTHERWISE NOTED.
B. C.
B
C
D
E
F
G
D. E. F. G. H.
D
AL08
DPHAG - 3
FLE DPHAG - 1
1 EM
AL01
FLE DPHAG - 1
A2
ARaD
ARb OFFICE 104
AL01
ARaD
3
E FLE DPHAG - 1
AL07
BL EM
4a b c d e
OS
OS
AL04
A1Fb
A1Fb BOYS 109
ELEC./COMP. 107
BVL
BVL
b
b
c
c
d
d
e
e
BVL
BVL
BVL
BVL
BVL
BVL
BVL
BVL
EM
AL04
b
b
c
c
d
d
e
e
BVL
BVL
BVL
BVL
BVL
BVL
BVL
BVL
DPHAG - 7
DPHAG - 9
DPHAG - 11
b
b
c
c
d
d
e
e
BVL
BVL
BVL
BVL
BVL
BVL
BVL
BVL
SHEET KEYNOTES AL01
EM
AL02 AL03
AL04
b
b
c
c
d
d
e
e
BVL
BVL
BVL
BVL
BVL
BVL
BVL
BVL
AL05
AL06
EM BVL
BVL
AL07
BVL EM
OS A1Fb
BVL
AL02
EM
O R T E I-V 3 K 5 4 G H C _ C N H U A IS T L E
A1Fb GIRLS 110
BVL
O R T E I-V 3 K 5 4 G H C _ C N H U A IS T L E
O R T E I-V 3 K 5 4 G H C _ C N H U A IS T L E
TOOL BL STORAGE BL 106
a
a
AL02
AL02
EG
a
a
BVL
BVL
EM 4a
5
a
a
BVL
BVL
EM
FLE DPHAG - 1
a
a
AL02
BVL EM
EG
SEAL
.
E
0'
4'
8'
82984 G
SS
IS T E R G IO N A L E N
PROJECT
3a
AL08
AG SHOP LIGHTING PLAN SCALE: 1/8" = 1'-0"
A
Digitally signed by John F. Heck Date: 2016.02.15 11:46:50-07'00'
NORTH
B1
E O F T EX
AT
JOHN F. HECK IV
FLE DPHAG - 1
DPHAG - 3
AL08
AL08
DIGITAL "KEYPAD" LIGHTING CONTROL STATION CONSISTING OF ONE (OR MORE) 1-GANG PUSHBUTTON DEVICES WITH MULTIPLE ENGRAVED "SCENE RECALL" BUTTONS FOR CONTROL OF PRE-PROGRAMMED LIGHTING WITHIN ROOM. REFER TO CONTROL DIAGRAMS AND SEQUENCE OF OPERATION ON SHEET E500a. ONE SWITCH; SWITCH TYPE AS INDICATED. WILL CONTROL THE LUMINAIRES IN ROOM. WALL-MOUNTED OCCUPANCY SENSOR, WATT STOPPER PW-100 OR APPROVED EQUAL. LOCATE PER MANUFACTURER'S RECOMMENDATIONS. SHOWN HERE FOR BID PURPOSES. CEILING-MOUNTED SENSOR, WATT STOPPER DT-355 OR APPROVED EQUAL. LOCATE PER MANUFACTURER'S RECOMMENDATIONS. SHOWN HERE FOR BID PURPOSES. LIGHTING ROOM CONTROLLERS FOR LIGHTING CONTROL SYSTEM IN THIS ROOM. REFER TO SHEET E500a FOR WIRING DIAGRAM AND ADDITIONAL INFORMATION ON ROOM CONTROLLER TYPE. CEILING-MOUNTED VACANCY SENSOR, LOCATE PER MANUFACTURER'S RECOMMENDATIONS. SHOWN HERE FOR BID PURPOSES. REFER TO SHEET E500a FOR WIRING DIAGRAM AND ADDITIONAL INFORMATION ON SENSOR TYPE. ONE PROGRAMMABLE TIME CLOCK WITH ROOF MOUNTED PHOTO CELL AND 4 POLE 20A CONTACTOR FOR EXTERIOR BUILDING LIGHTING. REFER TO DETAIL D1 ON SHEET E500a FOR ADDITIONAL INFORMATION. LUMINAIRE WILL BE CONNECTED TO LIGHTING BATTERY INVERTER "BAG1" LOCATED IN ELECTRICAL ROOM 107. REFER TO DETAIL B2 ON SHEET E500a FOR TYPICAL EMERGENCY LIGHTING BATTERY INVERTER DIAGRAM.
OF
4
AL02
DPHAG
AL03 BL
EM
BVL
E
EM
A1Fb
BVL
R
AL02
EM
BVL
EG
AL02 3
OS
K
A1Fb
ARb
JANITOR EM 108
K
C
ARb
EM
AL02
PR
3
a
S
ARb
HALLWAY 101
a
BVL
DPHAG - 5
EM
AL02
a
SHOP 105
ARb
AL08
a
R
ARaD
a
D
AL01
AL03
ARaD
DPHAG - 13
a
BL
OS ARaD
AL02
EM
E500a
OS
ARaD
a
EE
AL06
3a
E
AL05
RC
EG
EM
IN
CLASSROOM 102
RC
AL03
ARaD
EM
16'
B
200 LONGHORN ST. VEGA, TX 79092
ARaD
4a
FLE DPHAG - 1
EG a
STORAGE 103
OS
ARaD
2
EM
BL
I.
VEGA ISD CAREER TECHNOLOGY BUILDING
E
AL08
AL08
.
ST
A
Addendum 004 REVISIONS 4
02/05/16
ADDENDUM #02
5
02/15/16
ADDENDUM #04
DATE REVIEWED BY
Approver
DATE
02.15.2016 14-0424.002
PROJECT NO:
DRAWING NAME
A
AG SHOP LIGHTING PLAN
5
2/15/2016 9:31:38 AM
ALL KEYNOTE NUMBERS HAVE BEEN REVISED ON THIS SHEET SHEET NO
EL101 1
2
3
4
5
1
2
3
4
5
GENERAL SHEET NOTES A.
A
B
C
D
D
AP08 AP06
1 2
T
T
AG-RH-01
CLASSROOM 102
AP12 E500a
R/F
LAG2 - 29,31
AP06
R/F
R/F
R/F
LAG2 - 80
R/F
LAG2 - 82
LAG2 - 84
AP05
AG-FC-01
3
T
AP01
ELEC./COMP. 107
O R T E I-V 3 K 5 4 G H C _ C N H U A IS T L E
LAG1 - 35
AG-RH-06
T
AG-RH-07
T
T
LAG1 - 38
LAG2 - 32
LAG2 - 1,3
LAG2 - 81 LAG2 - 9,11
LAG2 - 2
AP08
O R T E I-V 3 K 5 4 G H C _ C N H U A IS T L E
O R T E IV C _ C N H U A IS T L E -3 K 5 4 G H I H N L E I
AP05
G
LAG2 - 13,15
G
G
F
LAG2 - 17,19
LAG2 - 6 G
G
LAG1 - 73,75,77
G
AP07
LAG2 - 10
AP09 T F
AP08
LAG2 - 8
LAG2 - 5,7 LAG2 - 4
LAG2 - 34
LAG1 - 59,61
P
AP09
LAG2 - 12
LAG2 - 36
LAG1 - 27
3
AG-RH-08 AP07
LAG1 - 9
4
TOOL STORAGE 106
AP06 AG-RH-05
AP10 AP11
G G
F
G
F T
AP09
AP12
5 AF03
DPHAG - 2,4,6
J
WG 14 LAG1 - 37
AG-AC-1
AP01
AP10
G
AP09
WG
AP08
AP09 AP08
AP09 LAG1 - 23
AP09
AP08
AP08 AP09
WG 16
LAG1 - 21
AP09
AP13
AP08
AP14
LAG1 - 16
AP15
LAG1 - 66 FA
AP04
AP01
AG-EF-04
LAG1 - 68,70,72
LAG1 - 6,8 AG-RTU-01
LAG1 - 25
AP01
AG-CU-01 LAG1 - 40,42
AP09
AD-1
AG-EF-05
AP17
AP13 PIV
AP14
FA
HOT BOX
AP18
AP13
AP19 5
JOHN F. HECK IV
E
0'
4'
8'
SS
IS T E R G IO N A L E N
PROJECT
AG SHOP POWER / FIRE ALARM PLAN SCALE: 1/8" = 1'-0"
82984 G
Digitally signed by John F. Heck Date: 2016.02.15 11:47:08-07'00'
NORTH
B1
A S
R/F
AP03 AP04
E O F T EX
AT
R
TJ LAG2 - 72
SEAL
D
AF03
FIRE ALARM CONTROL PANEL (FACP). REFER TO FIRE ALARM RISER DIAGRAM ON SHEET E601a FOR ADDTIONAL INFORMATION. REFER TO SHEET SERIES "MH" FOR LOCATION OF FIRE SMOKE DAMPERS OF DUCT DETECTOR LOCATIONS. PROVIDE INDICATOR LIGHT AT CEILING LEVEL TO IDENTIFY LOCATION OF DEVICE. REFER TO SHEET E701a FOR ADDITIONAL ELECTRICAL CONNECTION REQUIREMENTS. REFER TO "M700" SHEET SERIES FOR MECHANICAL / ELECTRICAL INFORMATION. CONDENSATE PUMP. RECEPTACLE IS GFCI AND WEATHER PROOF AND WILL BE PART OF UNIT. CONTRACTOR WILL PROVIDE CIRCUIT INDICATED. EXTEND POWER CIRCUIT TO FAN COIL UNIT INSIDE OF BUILDING. REFER TO SHEET E701a FOR ADDITIONAL ELECTRICAL CONNECTION REQUIREMENTS. DEVICE WILL BE RATED FOR 208-240V, 3PH & 50A. (4) #8 & (1) #10 GND IN 1 1/2" CONDUIT. MOUNT AT 42" A.F.F. DEVICE WILL BE RATED FOR 208-240V, 3PH, & 30A. (4) #8 & (1) #10 GND IN 1 1/2" CONDUIT. MOUNT AT 42" A.F.F. DEVICE WILL BE RATED FOR 208-240V, 1PH & 50A. (3) #8 & (1) #10 GND IN 1 1/4" CONDUIT. MOUNT AT 42" A.F.F. DEVICE WILL BE RATED FOR 120V, 1PH & 30A. (2) #10 & (1) #10 GND IN 1" CONDUIT. MOUNT AT 42" A.F.F. JUNCTION BOX WILL SERVE AD-1 AND ALSO HEAT TAPE ASSOCIATED WITH AC-1. PROVIDE A DROP CORD REEL RATED FOR 208V, 1PH & 50A. SECURLEY MOUNT TO CEILING STRUCTURE. DROP CORD WILL REACH 42" A.F.F. FROM FLOOR. PROVIDE A DROP CORD REEL RATED FOR 120V, 1PH & 30A. SECURLEY MOUNT TO CEILING STRUCTURE. DROP CORD WILL REACH 42" A.F.F. FROM FLOOR. PROVIDE A 1" CONDUIT TO FACP FOR FIRE ALARM CONNECTION TO SITE EQUIPMENT. REFER TO SHEET E601a FOR ADDITIONAL INFORMATION. PROVIDE A 1" CONDUIT WITH (2) #10 & (1) #10 GND FOR EACH CIRCUIT INDICATED. TIME CLOCK, PROVIDE A 277V CIRCUIT. REFER TO SHEET EL103 AND DIAGRAM D1 ON SHEET E500a FOR ADDITIONAL INFORMATION. MAIN GROUNDING ELECTRODE GROUND BAR. REFER TO DETAIL A4 ON SHEET E500a AND ELECTRICAL GROUNDING DIAGRAM ON SHEET E602 FOR ADDITIONAL INFORMATION. EXTEND POWER CIRCUIT TO CONDENSING UNIT IN EXTERIOR. REFER TO EP101 FOR ADDITIONAL INFORMATION. DEVICE IS FOR WALL MOUNTED SHORT-THROW PROJECTOR MOUNTED IN MULTI-SERVICE BOX. REFER TO MOUNTING DETAILS ON SHEET SERIES “T” FOR ADDITIONAL INSTALLATION INFORMATION.
EE
LAG1 - 19
AP11
AP12
AP03
J
ILP-1
AG-EF-01
AF01
LAG2 - 38
LAG1 - 39
P R/F
BOYS 109
LAG2 - 21,23
LAG1 - 64
AP09
T F
3 AG-UH-01
B4 E500a
OF
G
SHOP 105
SHEET KEYNOTES
AP08
LAG2 - 14
AP11
AP09
AP01
A3 EP101
R/F
LAG2
LAG2 - 25,27
E
T F
TAG2
R/F
R
DWH-1
R/F
E
B1 E500a
AP18
R/F
LAG1 - 63,65
B4 E500a
3
C
AP09
LAG1 - 80,82,84
PR
G
LAG2 - 78
R/F
2
LAG1 - 4 HALLWAY 101 LAG1 - 12 LAG1 - 3 JANITOR LAG1 - 10 108
T F
AG-RH-04
LAG2 - 76
LAG1 - 62
LAG2 - 40
G
LAG1 - 1
LAG1 - 34
AP08
LAG2 - 16
3
4
T
AG-RH-02
AP09
B1
4 WG
GIRLS 110
G
IN
4
F
T
AG-RH-02
LAG2 - 74
LAG1 - 41
OFFICE 104
LAG1 - 14
LAG1 - 43,45
AP07
LAG1 - 17
AP09
3
LAG1 - 51,53
F
LAG2 - 20 LAG2 - 33,35 LAG2 - 37,39 LAG1 - 79,81,83 LAG2 - 79 LAG2 - 22 LAG2 - 18
LAG1 - 47,49
LAG1 - 13
G
LAG2 - 26
LAG1 - 5
1
G
AP09
F T
G
G
AP09
WG
AG-EF-03
LAG2 - 24
LAG2 - 42
1
AP19 2 1
G
AP09
18
AP09
AP09
16'
B
200 LONGHORN ST. VEGA, TX 79092
2
AP08
G
LAG2 - 30 LAG1 - 11 LAG1 - 7 LAG2 - 28 LAG1 - 55,57 LAG1 - 74,76,78 LAG1 - 36
P LAG1 - 2
F
G
FACP
F 2
AP09
AG-EF-02 WG
VEGA ISD CAREER TECHNOLOGY BUILDING
WG 14
1
AP08
LAG1 - 15
F T
AF01
G
ST
1
F
LAG1 - 18
AP09 STORAGE 103
E
GFCI RECEPTACLES WILL BE INSTALLED AT ALL LOCATIONS AS REQUIRED BY THE LATEST VERSION OF NEC, STATE AND LOCAL CODES WHETHER INDICATED ON PLANS OR NOT. SOME LOCATIONS WILL BE WITHIN 6'-0" OF SINKS, EXTERIOR DOORS AND WET LOCATIONS. ALL EXTERIOR RECEPTACLE LOCATIONS WILL BE GFCI RATED AND WEATHERPROOF.
Addendum 004 AP17
TAG1
REVISIONS
DPHAG
ELEC./COMP. 107
4
02/05/16
ADDENDUM #02
5
02/15/16
ADDENDUM #04
LAG1
AP15
A3
ENLARGED ELEC./COMP 107 - AG BLDG
DATE
SCALE: 1/4" = 1'-0" REVIEWED BY DATE
Approver
02.15.2016 14-0424.002
PROJECT NO:
DRAWING NAME
A
5
2/15/2016 9:43:49 AM
ALL KEYNOTE NUMBERS HAVE BEEN REVISED ON THIS SHEET
AG SHOP POWER / FIRE ALARM PLAN
SHEET NO
EP101 1
2
3
4
5
